Pavilion 1bus50 g6: laptop does not start. Screen remains blank, but the caps lock and keys turns on wifi.

Similar Questions

• My iPod 5th generation does not start (it will stay on the apple logo) and will not be detected by iTunes.

  Last night I tried to turn on my iPod that has not been loaded. I plugged it so that it can start loading. I think the iPod as was the accused, has no need for me to start and should have done by itself. When I pressed the button home to start using it, I noticed it was not on. Then I pressed the power button and then saw he was showing the Apple logo and then it turns off again. I tried pressing the "home" button and the Start button / stop at the same time and the same thing will happen. I also tried connecting to my computer and it did not recognize.

  Try the remaining actines of the:

  - iOS: do not respond or does not light

  -Also try DFU mode recovery mode post-test

  How to put iPod touch / iPhone in DFU "Karthik doodles."

  -If failed and that you cannot completely turn completely the iOS device, leave the battery to drain completely. After loading a hour repeat the foregoing.

  -Try a different cable

  -Try on another computer

  S ' there is still not successful that usually indicates a hardware problem and an appointment at an Apple store Genius Bar is in order.

  Shop Apple Store - Genius Bar

• Installed new module memory for laptop, found original was bad, while windows Vista does not start by going blank after the "status bar".

  I have a Windows Vista running on a Sony VIAO laptop and has been updated with level 3 to 4 GB of memory. During the memory test, I found that 2 GB of original module was bad and replace it with the new 2 GB module end back where I started with 3 GB. However, Windows starts only at a little past the rectangle with 3 points moving ("State Bar"?) and them it goes to black and the desktop never appears. I tried to roll back to the last working version of Windows settings, but always the same results.

  What can I do now? Is there a way to check and fix disk errors?  Is it possible to install Windows XP Pro or I have to go to Windows 7.  I even has System Mechanic Pro running on this laptop and it did help some casued the problem. It's as if the disc is damaged for some reason any.  Only with Vista felt this helpless.

  It seems to me that the new memory you have installed is bad or incompatible with the system.  First, remove all chips and reinstall them and then try to make sure that they are correct and secure again - don't just press them in place, effectively remove and the replacement and make sure they are in the right direction.

  Boot from the Installation of Windows Vista genuine disc (or you can borrow from someone) or a recovery disc with recovery options included in this topic. If you do not have a floppy disk, you can make a bootable recovery disk by using http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/ with burning software like: http://www.snapfiles.com/get/active-isoburner.html and, of course, a blank CD (perhaps made on another computer, or perhaps in SafeMode with network if it does not - that would be a good sign if it is true). You may need to change the BIOS to do first the CD drive in the boot sequence to boot from the CD.  To do this, hold the screen that tells you the key F to push to enter the menu start or start of installation.  Push it quickly. Make the changes, save your work and exit.  Put the CD in the drive and reboot.  When you are prompted, press any key to boot from the CD.  Select recovery options and follow the instructions until you see the menu.  Once there, select the Windows Memory Diagnostic tool and run it and see what it says.  If it detects problems (and I suspect it might), you may need to replace the new chip memory.

  I hope this helps.  If this isn't the case, after return and we will try other options.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Laptop does not start... says windows 'the Proxy Server is not responding.

  Laptop has just received an automatic update of windows and after that, I get the message on the remote control unit does not accept the connection... I only put in place that I use a router w/data cable to connect two computers remotely

  Whasssup, "Jay"?

  Were there any changes made on the computer before the show?

  You can get this error if there is no proxy server is configured on the computer or due to a third-party program. Follow these methods to solve the problem:

  Method 1:

  I suggest you to follow these steps and check if that helps:

  1. open Internet Explorer.

  2. click on Tools and then click options Internet.

  3. click on the tab connections , and then click LAN settings.

  4. uncheck the option use a proxy server for your LAN.

  5 place a check on automatically detect connection settings.

  6. click OK twice.

  You can also see the article for more information:

  Change the proxy server settings in Internet Explorer

  http://Windows.Microsoft.com/en-in/Windows7/change-proxy-server-settings-in-Internet-Explorer

  Method 2:

  Refer to the article to verify if a violin is the cause of the problem:

  [Violinist] Difficulty "the proxy server is not responding" problem caused by a violin

  http://blogs.msdn.com/b/tfang/archive/2012/07/18/Fiddler-fix-quot-the-proxy-server-isn-t-responding-quot-problem-caused-by-Fiddler.aspx

  Let us know if it helps.

  Good luck, mate!

• HP Pavilion 15-n200: laptop does not start up - gel

  My laptop has been recently upgraded to Windows 10 by a local COMPUTER company. After about a week of normal operation, it is no longer starts. E HP logo appears then freezes completely. I tried to re start several times, but it has not solved the problem of thew

  some of my documents (Word, exel, etc. are saved, but many are saved locally. These documents are really important to me and I can't save as I can't start my lap top.

  Any help would be greatly appreciated Br

  Thank you very much

  Carl

  Hello Visruth,

  Well good news, laptop fixed and running like a dream.

  I performed a chattr computer who has lost all the apps that have been sorted to the question of the gel. Since installed all apps and personal settings and everything works perfectly again.

  Thank you very much

  Carl

• 2000-2D02TU HP: HP 2000-2D02TU Power LED power switch but the laptop does not start.

  Someone help me.

  HP 2000-2D02TU Power LED power switch but the laptop does not start.

  What I'm doing.

  Please help me

  Model No. - HP 2000-2D02TU

  Hello @Alok_Bhai,

  Thank you for visiting the HP Forums! A place where you can find solutions for your problems, with the help of the community!

  I read your post on the laptop won't start does not and wanted to help you!

  You indicate that the lights are flashing, but the laptop does not start?  If this is the case, try to review the following document and let me know how it goes:

  Computer does not start and emits a LED or beep Code

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution' , this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• Pavilion dv6: computer HP pavilion laptop does not start and I do not see the screen because it's broken

  I have the HP pavilion computer laptop windows 7 and I broke the screen about a year, I can't see the start menus. I have been using an external monitor and it has always worked well, but now I can't see how to fix my computer to boot.  I did a hard boot but nothing happened, and with a broken screen, I can't see any of my options on how to fix it.  It does not start.  Looks like it is, but because I don't see the menu F8 or Boot, I can't call themselves that the screen can be done.  Help, please.

  Hello @SPKaler,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums, I would like to draw your attention to the HP Forums Guide first time here? Learn how to publish and more.

  I read your post on the issue with the laptop won't start does not and wanted to help you!  I understand that the screen is damaged and you are using the external monitor to view the screen.  However, now that the laptop does not start, you can see is more of the external screen to see what is happening.

  From my understanding, you should not be able to see an image on the external monitor, until you start the operating system.  You can try to perform a system restore by using this document:

  HP computers - performing a recovery of system HP (Windows 7)

  You may be able to follow along, long enough until the image is displayed on the external monitor.  Otherwise, you can contact HP support by phone, for additional options.

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• Laptop does not start the screen to the top/black/blue

  Laptop will not start. HP Elite Book 250. Doesn't boot. Tried start run but says departure until a failed. Help, please.

  Hello Everlast87,

  Welcome to the HP Forums! I hope you enjoy your experience!

  I understand that your computer will not start correctly. I will do my best to help you with this problem! For help, try the procedure described in this document from HP: computer does not start

  This document contains the steps such as resetting the laptop and more, corresponding to the exact symptoms. I believe that this document will solve the problem. If this isn't the case, I would contact HP support by phone using equipment. You can use this Web site for information about how to contact HP properly, based on your region: Contact HP worldwide

  Since it a commercial product, you should post your question on the card for laptop of HP Enterprise Forumsfor more information.

  Please let me know if you have any questions or concerns. Thank you for bringing This problem on the HP Forums. Have a great day!

  Mario

• Laptop does not start

  My laptop froze and I had to force a stop to turn it off. Since then, it does not start upward. It shows the Toshiba screen briefly as usual then goes to a screen asking me to start up as usual, or try to repair the startup problem.

  If I choose to start up as usual it displays the Windows logo and then after a short period back to the previous screen, if I choose the option repair the screen turns white with a white arrow cursor display and then nothing seems to happen. I left this white screen on during a few hours, but nothing.

  Any ideas?

  Start your laptop and press F8 to display the advanced startup options.
  It work?

  If Yes please try to start the operating system in safe mode. Can you do this?

• My laptop does not start after cleaning

  Hello
  I knew an overheating problem on my laptop.
  I therefore decided to remove a processor heat sink and empty dust. It was released with processor...
  There was a huge load of dust, so I cleaned it, put new thermal paste...

  Now computer laptop does not start loading Windows.
  It checks only the CD, HARD disk, and that's it.
  Screen is blank, ON the indicator led is on.
  Two fans periodically start to turn (when they stop radiator heat - so the processor works)

  Where is the problem?

  Thank you

  Hi Dubas,
  You can access the BIOS when you try to start your laptop? This can give you a clue as to why the OS will not charge.

  Kind regards

• HP-gs61-110sa: help! laptop does not start

  Help, please! Laptop does not start. Looking at the black screen with cursor flashing at the top left.

  Hello

  If you do not, use another PC to create a Windows 7 repair CD.  Download the ISO from the link below.

  Windows 7 64 bit

  You must use an app like ImgBurn to burn the ISO to a CD ( Note: you can deselect additional software during installation of ImgBurn options)- hereis a guide on the use of ImgBurn to write an ISO on a disc.

  One time created, or if you already have this, typing away at the esc key when you launch Notepad to open the Start Menu.  Insert the CD to repair.  Select boot options ( f9 ), use the arrow keys to select the CD/DVD drive and press ENTER.  You can also get a prompt to "Press any key to" continuous - it if requested.

  When loading, select repair your computer and choose the command line.  When this charge, enter the following commands and press on enter after everyone – including spaces as shown.

  Bootrec.exe

  bcdedit/export C:\BCD_Backup

  c:

  Boot CD

  BCD attrib s h - r

  Ren c:\boot\bcd BCD.old

  Bootrec /RebuildBcd

  Bootrec /fixmbr

  Bootrec /fixboot

  Remove the CD from repair and try to restart the laptop.

  Kind regards

  DP - K

• Laptop does not start > how to delete data

  Separated from this thread.

  How can you get your data off when the laptop does not start again? "catch fire or explode"... in a suitcase on a train or plane? This sounds like a product ready for the market yet? More I explore this question of "overheating" in the line it worse it seems: my machine was like a hot plate not a laptop when it has been completely unfolded in a cool room: about right to mention briefly without getting hurt. (And my data is still inside of her, if it is not melted...)

  Well, unlike a laptop where you can remove the hard drive, these tablets are pretty well fixed and specifically your case, (it will not explode or catch fire) is to locate the device next to an air conditioner or a blowing unit to blow fresh air into the vents.

  At this point, press on and hold the volume button upwards and at the same time, press and hold the power button for about 15 seconds, then release it.

  If you can get it to feed and at least screen troubleshooting, see if you can get the machine to run in safe mode.

  If you can get to the desktop, you can down all your data by opening the file manager, click on 'This computer' and open the 'users' folder, go to your account name folder and copy all the files on a USB key.

  It is the only way to get your data out of these tablets.  You can't have the SSD card to remove it to try to force the machine to run at least once.

  Now, I think that your machine is still active, just overheating.  Get off in any case data.

  A RESET and reinstall updates are the only thing you can do.  I have the i3 model myself and am on it now and no problems with it.  Some games will heat, but never to the point that everyone is a report.

  If all fails, send the replacement machine.

• my power green LED flashes and the laptop does not start

  Mr President, I have laptop computer Sony vaio, when I press the power button, my power LED green light begins to blink, sometimes sometimes brighter Sun, but nothing else happened, my fan remains closed, screen remains black, just POWER green LED flashing, flashing in the same way as orange light flashes in case of in standby mode, it is usually solid green , but now it flashes and the laptop does not start, what should I do Sir...

  My model number is the model of Sony VAIO PCG-61911W... His VPCEG18FG of the product name

  ankurgupta53,

  It seems that your device is not post.  You can try reinstalling the ram or simply by using a single module at a time, but other that that the device would need service...

• Laptop: laptop does not start

  My laptop does not start, how can he?

  Hey,.

  First, a good thing to try is a hard reset of the computer.  The steps are different depending on whether your battery is removable or not.  See http://support.hp.com/us-en/document/c01684768 for steps and videos covering this first easy step.

  If you are still having problems starting to walk through the steps in the troubleshooting online here documents:

  Windows 10 - http://support.hp.com/us-en/document/c04718479

  Windows 8 - http://support.hp.com/us-en/document/c03515402

  Windows 7 - http://support.hp.com/us-en/document/c01443371

  -wes

• Laptop does not start with the connected usb device

  Hello
  Voila, I have a Sp6100 Pro Satellite, when I try to start whith a usb printer is connected, the laptop does not start. I have the latest version of the bios 1.90.

  THX,
  Barzot @+.

  Hello

  What you mean with start won t at all? Is there any kind of reaction if you press the power button / stop?