Pavilion Entertainment PC questions after recovery

Similar Questions

• Laptop HP pavilion 15-e015tx: error after recovery

  I was faced with an error when turn on PC, so I called HP support and they sent me 3 recovery disks. and I did the whole recovery process according to them. but when my pc restarts after recovery happens a screen to install the software from 1 h to 2 h and my laptop restarts several times and this screen will appear. Help, please
  
  And I do something Meanwhile process failed in the face of an error in the software installation screen

  Just be patient and wait until she finishes, it takes some time. Don't worry too much.

• HP Pavilion Entertainment: HP Pavilion Entertainment laptop recovery

  Hi, my HP Pavilion Entertainment computer laptop power on password after 3 failed attempts he said system disabled 58773831.plz give me a password.

  Hello

  Enter: 47651217

  Kind regards

  DP - K

• my hp pavilion entertainment dv6t 2000 pc formatted and I don't keep recovery DVDs

  my hp pavilion entertainment dv6t 2000 pc formatted and I don't keep recovery DVDs

  Hello

  No, you can not download, you will need to order that the recovery disk set as I mentioned in my previous post.

  Kind regards

  DP - K

• Pavilion Entertainment PC dv6: need a new hard drive for the dv6-1230us

  My question is about the HP Pavilion Entertainment dv6-1230us PC. Recently, it was abandoned, and since then it has been giving me the following message if poster every time it starts.

  Not found boot device
  
  Please install an operating system on your hard drive.
  
  Hard Drisk (3F0)
  
  F2 System Diagnostics
  
  "For more information, please visit: www.hp.com/go/techcenter/startup"
  
  I know it's important to run the hard drive test, but when I run the diagnostics of the system for the Test drive, it says:
  "HDD test failed.
  There is no hard drive.

  I was also on the proposed site and even after "reset my BIOS to default", it recommends running the hard drive test, which does not simply because it has not really helped me the "there is no hard drive. There was a YouTube video that I came across thus suggested pulling the hard drive and diconnecting and reconnect to correct the error in this case that the son is detached, but that no longer works.

  SO, I don't know if there is anything more that I can do, I guess that the hard drive is super dead.

  It comes with a Seagate ATA hard drive. I was wondering if I could replace it with a SATA hard drive or should it be an ATA? (Even has the material capacity to support a SATA drive?)

  Also, it is even useful to replace the hard drive? Should I get a new laptop instead? This laptop is used mainly for just browsing online and checking emails.

  Any help is appreciated, thanks.

  Yes, the hard drive is so dead, that he not yet register as a hard drive. The dv6-1000 series certainly uses SATA, not ATA drives so I'm not sure of what you see. You can replace it with any drive SATA 2.5 inch width 9.5 mm thick.

  Watch this video between: 53 and: 59 and see that it's a SATA drive. If yours is different, so you have confused with your model.

  https://www.YouTube.com/watch?v=QQx7PlIXFuE

  Hard disks are a small fraction of the cost of a laptop and if your what it takes to, I would say that to replace the hard drive rather than buy a new one.

  It is an excellent drive at a great price:

  http://www.Newegg.com/product/product.aspx?item=N82E16822236563

  You have recovery discs? You run Windows 7? Post back if you need help more to restore system software.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP plugged music after recovery?

  HP Pavilion Ultrabook 15-b005eo with 8 64-bit Windows.

  Another question for today.

  Last week, I bought this laptop yesterday I did a factory reset because HP 3D DriveGuard had ceased to work telling me that hard drives are not supported. I tried all of the solutions provided by this forum and it still does not so I decided to try the factory reset I had nothing special on my computer yet - or that's what I thought.

  As the name of 'factory reset' suggests, the computer would be re-established, on the condition that I received it in.
  Almost everything was the way I was expecting. Except Norton and HP plugged music were missing. Not a big deal for Norton can be downloaded from their site, but music connected to HP is not available from their or your site. It is not yet available from the Recovery Manager.

  I had not yet activated the trendy music trial.

  Is there a way to get this back? There should be, because it is still a new computer, and it means I have the right to 90 days of the trial, right?

  PS. DriveGuard started working again after recovery.

  Hello! Problem solved!

  Here's how it worked:

  I saw this one blogpost for the installation of Windows 8 cleanly without the 'bloatware' for computers that came with 8 Windows pre-installed. There was in the blogpost instructions to use Windows built-in 8 'reset the PC' - function to get rid of the pre-installed programs and come back only to win 8. But in the section comment each commentator said that it did not work and all (incl. "bloatware") is restored when you use this function.

  I decided to try this and it worked! Everything that has been installed on this computer is returned including HP connected with music. It's a little weird when you use Recovery Manager it does not install connected with the music but when you use the built-in function of Windows 8, it is

  I would like to especially thank Jeff who got in contact with the support e-mail client. Although they do not really have change to really help me because the weekend came gives me a change to ask two things one another, so the contact with the customer is not useless.

  Thanks again for the help and I wish you guys.

• HP Pavilion Entertainment PC: Initial password

  Hello, I was cheking your laptop (Hp pavilion entertainment pc dv2000) I had long turned off... The thing is that I don't remember the original password... It's like a background dark and in the center of the screen, it appears blue advertising, asking me 'Enter password'...

  I tried everything: typing esc after start-up, in tapping f2, f8, f9, f10, f12; also, I did the procedure to remove the RTC battery but, advertising is still apearing.

  Could you help me please? Anya

  Hi, Juanca:

  Enter a password for BIOS 3 times, and the PC should generate a code system off (stop).

  Then read the first post on the link below for what to do with the stop code that you received from the PC.

  http://h30434.www3.HP.com/T5/notebook-operating-system-and-recovery/system-halt-error-message-or-BIOS-password-reset-generator/m-p/5010033

• Windows does not start after recovery

  Hey, satellite 1800 started son to have more and more slow to the point where it took close to an hour to boot in Windows. It got to the stage where it seemed that recovery from the CD was the only road - so we did. Everything had to look successful from the point of view of recovery but the installer of Windows XP displays "Please wait...". "with the normal activity of the disc looking for 20-30 seconds and then hangs - no disk activity, the mouse is not responding. I went through the recovery in "expert" mode and don't see any problems with the recovery process. Issues related to the:
  1 no matter who else seen elsewhere?
  2. what else can I do diagnosis-wise?
  3 which, basically, the recovery process not / (fact he re - format partitions, could it have left a virus?)
  4. I'm better h/w or s/w diags?

  Bitshifter

  Hi Bitshifter,

  topic of your question 3:
  The recovery process replaces the whole HARD drive or even a partition with an image created by Toshiba. This image contains an operating system, drivers, and a few basic programs. All other data (including viruses) in this partition will be deleted.

  question 4:
  I don't know the cause of your problem, but I think it's a hardware problem, because after recovery, there may be incorrect or missing software.

  Sorry I can't give you more information.
  Good luck!

• HP-Pavilion Entertainment PC DV9700 reconstruction

  I have a laptop HP Pavilion Entertainment PC DV9700, - p / n - nr # ABA Service Tag DV9925 FE695UA
  With Windows 7
   
  He began to present video failures overheating, with an outdoor fan, the "cooling" and may continue to run, then didn't is more turned on, take him to a local technician and repaired trotted for several months, then the total failure of the present, which has revived, the technician told me that the video card model came with a factory problem and it happened that He responded with the warranty, my laptop while it is outside the warranty, I still want to solve this problem, if I have to pay for it, I'm in the Dominican Republic, where the temperatures are very high, which coupled with the motherboard originally in the failure would ruin once again, if you put the motherboard that was the second solution is to replace the technicians the original AMD MB for one that fits and works more advanced INTEL brand.
  1. where can I get this motherboard?
  2 - What is your reference (INTEL)? It's HP-461068-001
  3 - HP has a place where laptop computer rebuildingthis in Dominican Republic? ,
  3 a-where?
  4. I have a small factory where I have several produced primarily HP printers and multifunction.
  They have workshops at Santo Domingo, Dominican Republic (multifunction), printers HP Officejet Pro 8600?
  Thank you

  I think I understand most of your questions. The repair on this motherboard is called a "reformatting" and I guess that's what your technician did before. It is true that you can surely make a reflow second on the same motherboard. Each of them liked lasts more short than the previous. You need a new motherboard. There is a motherboard for the series dv9700 with an Intel processor and chipset. That means you, the 461068-001 is an Intel processor with a chip nVidia video. Those who still have questions. The desired one is 447984-001, which is an Intel processor, Intel graphics card.

  Here it is on eBay:

  http://www.eBay.com/ITM/tested-and-working-Hewlett-Packard-447984-001-Pavilion-dv9500-motherboard-/261173594858?PT=motherboards&hash=item3ccf28caea

  This model may require a few changes to fit exactly to your chassis case. He won't have the same graphic power like your old laptop. You also need a processor and a new radiator.

  At the point where you've done with this project you will have invested enough to get a new laptop. Your call. If you want more help spread the back.

• HP Pavilion g6-2320tx Notebook PC - recovery disc is scratched on the other creating recovery disc

  HP Pavilion g6-2320tx Notebook PC - recovery disc is scratched on the other how to create the 2nd recovery disk recovery disk

  Please contact the official support of HP in your region / country, HP support worldwide Portal, to see if the HP recovery support is available for your computer.

  If you have any other questions, feel free to ask.

  Please click the White Star of KUDOS to show your appreciation

• Pavilion dv5 startup question point

  This morning when I got to the top of my dv5 Pavilion (with Vista installed), after showing the logo of HP, the screen went black and does nothing else. I have repeated many times and also tried going to the start menu, all this without success. After Googling the problem, I tried to remove the battery (which is 6 years old and has absolutely no charge) and cable load and hold the power button for about 20 seconds. Someone on a forum I read stated that it needed to dump any residual charge in all of the material. However, after replacing the battery and charging cable, the problem persisted. Another source suggested commissioning with the battery removed, linking directly to the power of the charging cable. It worked.

  My question is if someone can explain WHY it worked. What difference does make if the power comes directly the supply cable vs from cable, thanks to the battery, then the material?

  Sebastian42 wrote:

  I already assumed that the battery has not (or close to it). Even when the power cable is connected, the status of the battery in the bottom right of the screen shows a constant load of 0%. The only reason why I have let in the laptop at this point is because it feels strange to have a big hole in the lower part of the machine. I have not replaced because I never really need the laptop in a place where there is no outlet and do not see the point of spending money (I'm a poor student, after all).

  When I said "battery replacement", I only intended put the original back in.

  When the computer is started at the beginning, the BIOS temporarily control the charging of the battery until the OS has finished starting? Yes And if so, the fact that the battery is more charges bring somehow the BIOS to get stuck before can start the main OS?

  I guess what I'm asking is this: the BIOS tries to start to charge the battery and then get caught in some kind of loop when loading does not work as usual, thus preventing the later stage of the start-up of the main OS?

  I would remove the battery until a replacement is available. A lot of people this, when a laptop is used only as a replacement of PC desktop. It does not hurt a thing.  When a failed battery is left in place, you take a chance.

  On the inside of the battery, the battery pack controller card failure is likely to be the reason why the laptop does not start in Windows with the battery installed.

• fqdn ping fails after recovery from sleep mode

  client system is win7 64 bit

  Server DSN is isc bind 9.7 works on win 7 64 bit

  local system of fqdn ping fails after recovery from sleep mode.

  I do not think that the ping never hits the network.

  Nslookup of full domain name or name of the system only exists.

  the system name ping only succeeds.

  then after ipconfig/release, ipconfig / renew, successor to ping the domain name full local system.

  someone at - it thoughts or ideas?

  Hello

  From the description of the problem, it seems that your computer is on a domain. I suggest you post the same question on the link below. The link given below is link TechNet Support for Windows 7. The question facing you is best for TechNet forums.

  https://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking

  Feel free to write us if you have any other issues related to Windows.

• Partition lost after recovery - Satellite L30

  I had two partitions on my HD (Satellite L30-114).

  I used the Toshiba recovery Cd to restore windows back to my laptop. The CD has not offered me a full mode or an Expert as written here http://support.toshiba-tro.de/kb0/FAQ350072001GR01.htm he has just recovered without any input on my side!

  After recovery, Windows does not see my second partition. I used the disk management utility, and it is said there are 17 GB of disk unassigned space (this is my second Partition!).

  Can and how can I restore it?

  TX a lot!

  Hello

  It seems that the L30 comes with a new version of the recovery cd.
  I think that the recovery procedure is a bit different than the old with 2 different recovery modes (standard and expert)

  I know a little new recovery procedure because a friend of mine bought a new Satellite with this recovery CD. He asked me for the installation of the laptop and we checked.

  It seems that you must press the setting button after the language selection.
  If you n t use the button setting for the configuration if the recovery procedure will be remove and erase everything on the HARD drive. I think you didn't configure the settings and therefore all the partitions have been deleted.

  Unfortunately I think that there is not much to do. You the partition has been deleted and it of not possible to bring back the lost data.

• Question on recovery by Satellite L300D model: PSLC8C-040019

  Hello! Just a quick question about recovery up to a factory default.
  I've had this phone for almost 2 years now and just I am planning to reformat. I tried the trick 'keep power and zero' that didn't work, then I discovered that I could create a recovery disk, tried that today ' today and I get a message "No disk HARD recovery area" I checked on the hidden partition records management is there.

  Can someone help me on this.

  Thank you!

  Hello

  If you receive such a message, it means that you unable to do a restore disk or restore the factory settings. You must order for money

  https://backupmedia.Toshiba.EU/landing.aspx

  or make a copy of windows installation and install all drivers

• Satellite M40X 299: no boot after recovery

  Hello

  I have a problem with my satellite M40. After a problem with spy software, I tried to format my pc.
  I did a restore of the system with the original cd. At the end of the mind, I pressed ctrl + alt + delete to restart as it was written.
  But nothing happens, I have only a cursor in the upper left corner of the screen and windows does not start. I did the operation 3 times and it's always the same result.

  I don't know what more I can do.

  Thanks for help.

  Excuse me for my English

  It's very strange. Can you get the CD of Microsoft facilities and try to install the OS? I'm really interested if the same thing will happen again.

  Please don't be crazy on me because I t n wrote a few exact explanation but after recovery without end I've done in the last 8 years I have never seen anything like it.