Pavillion 500 - c60: two different monitors as multiple monitors

Similar Questions

• Running two different monitors res - GPU requirements?

  Ladies and gentlemen,

  I will build a computer to work again-photo PS CS4 and asked in a previous thread on current graphics cards largely support the requirements of Photoshop. The answer was: the cards PCI - e current will do it. Now I realize that I want to run two monitors of the card I buy and all my research cannot come (here) with a response.

  I have a Viewsonic 2030 monitor b good 21 "for graphic design professionals (OK, it's an LCD screen so I don't know there limits...) which runs natively in 1600 x 1200. I also have a gateway 24 "that runs in 1900 x 1200. I want to calibrate the Viewsonic, display images on that and book the bridge for pallets of tools and other applications, etc. It would be a bonus even greater if I could run only in the portrait, the front door as I often even now. Both will have to run from a DVI signal. VGA signal too 'soft '. So, I know that the graphics card must have two DVI-out connectors.

  This ability would be worth extra cost on a low-end card. May be no big deal, absolutely assumed - and this is why it is not mentioned in the FAQ, knowledge and other databases. Although I went to nVidia, I would buy an ATI card equipped to achieve this functionality if it is what was needed. I also know that I will probably have to give up one of the slots with a bulky card. I think it will be OK, as there only seems to be a lot of requests on the slots these days with so much available through the-motherboard chipsets. (My generation was on a conservative Intel card to end 2003 - no sound - and the integrated LAN chip went soon afterwards to a bolt of lightning nearby...! No. IEEE 1294 to all and not enough USB, etc. etc.)

  Thanks in advance for comments, everybody.

  jonathan7007

  again, any card should be well enough just make sure you get a card with either a DVI or DVI ports and a HDMI converter port + DVI.

• View two different windows simultaneously with an internal and an external monitor

  Display two different windows on external and internal monitors at the same time?

  Yes, you can.

  When you connect an external monitor, its pixels are added to the screen integrated to create an extended desktop. If you get a double built-in, just disable fill video. The pane organize you allows to place each tiny in the same way screen icons, they are arranged on your bench, and then the mouse moves correctly on the boundary between displays, and you can drag and drop Windows where you want.

  

  .

• image of different desktop to multiple monitors

  I have two monitors and want two different pictures on the desktop monitor.  Any thoughts?

  Thank you

  Hi Paul AZ,.

  See the following article:

  http://www.Microsoft.com/windowsxp/using/Setup/learnmore/northrup_multimon.mspx

  I hope this helps!

• Screensavers dual monitor. Display two different screen savers on two monitors.

  I can see two different screensavers on two monitors?

  Hi daveschwab,.

  As far as I know, it is not possible to have two different screensavers on a double configuration monitor.

• How to connect the laptop screen to two different TVs?

  I try to show what is on my laptop two two different TVs at the same time. I already have the hdmi cable connected, but I can't seem to find a way to show my monitor on both screens at the same time. I can get it to show on one or the other. Any suggestions?

  Thank you
   
  Original title: connection screen of the laptop to two screens

  Hi GabrielGomezYZ,

  Thanks for posting your question in the Microsoft Community Forums.

  You have a problem with the display of the content on the laptop on more than one TV. It can be difficult when something that is important to you does not work as expected. It's pretty simple and we're here to help you solve the problem. We work as a team and get this sorted out.

  Method-

  I would have you look at the article-

  Setting up dual monitor: two screens are better than one

  http://www.Microsoft.com/athome/organization/twomonitors.aspx#fBid=DT7eyPCoaLh

  In addition, you can check the items of reference-

  Work and play better with multiple monitors

  http://Windows.Microsoft.com/en-in/Windows7/work-and-play-better-with-multiple-monitors

  HDTV: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/HDTV-frequently-asked-questions

  We know if you need help. We will be happy to help you. We at Microsoft, strive for excellence and provide our customers with the best support.

  Thank you.

• Two different language versions of Firefox at the same time?

  I am running Windows 7 Home Premium. I have two accounts, one for me and one for my wife. She uses Firefox (Japanese), and I've been using another browser. But I would like to firstly using Firefox (in English).

  Is it possible to run two different language versions of Firefox on the same computer? I want to be able to run both at the same time... (So if I navigate and she wants to check an auction quickly it can without my duty close my browser).

  Can be done with relative ease?

  Make sure that each of you has their own Firefox profile folder.

  See:

  • http://KB.mozillazine.org/Creating_a_new_Firefox_profile_on_Windows
  • http://KB.mozillazine.org/Shortcut_to_a_specific_profile
  • http://KB.mozillazine.org/Using_multiple_profiles_-_Firefox

  You can add - no.-distance to the command line to open another instance of Firefox with its own profile and run multiple instances of Firefox at the same time.

  • http://KB.mozillazine.org/Opening_a_new_instance_of_Firefox_with_another_profile

• Can I connect Macbook Air to two external monitors?

  I have the MacBook Air (13 inch, early 2015), one of the monitors is already connected via DVI/Thunderbolt and given the MacBook Air only have port a thunderbolt and two USB 3.0 ports, is possible that I connect the other monitor from other ports.

  OS X El Capitan: connect multiple monitors to your Mac

  Can I connect two external monitors to my macbook air

• Tecra Z50 - need to connect two external monitors

  I think to buy Tecra Z50, but one of the features that I need is the ability to connect two external monitors.

  Is it possible to have a monitor connected to the HDMI and a VGA (with computer laptop lid closed)?

  * Hi-speed III Port Replicator is not an option, because it is not available in my country (Croatia).

  Hello

  I don t think you will be able to connect two external monitors to this laptop using HDMI and RGB port at the same time because of different types of signals.

  The RGB/VGA port supports analog signal.

  The HDMI port provides the digital video output and when the external monitor is connected to the HDMI port the device is set to HDMI.

  > * Hi-speed III port replicator is not an option because it is not available in my country (Croatia).
  What of the Dynadock? Its an external device connected to the s for computer laptop USB port.
  It supports own graphic unit and you can connect to another external monitor such Dynadock 2nd.

• Pavilion 500 - C60: new office reads, "ERROR: no boot disk was detected or the disc has failed" at startup.

  Just bought Pavilion 500 - C60, running Windows 8.1 64-bit and am doing everything on old HP running Windows Vista Home Premium SP 2. Has not gone smoothly from one thing to another, but I think everything comes together. A couple of days, began to receive the error message at startup or, if I COULD do so that it starts would go for awhile and then would get an ERROR message, requiring restart. Usually after obtaining the error message several times, the computer would then initialize. Tonight, I couldn't override the error message for anything! When you press power button / stop, I hear (HD) running for a few seconds, everything is silent, and then the error message appears on the gray screen dark in white letters, BACK very and sinister looking! Any suggestions? Had the computer about two months and it has not been easy.

  Not good!  Check all the connectors and the hard drive to make sure that they are correctly wired in place. Make sure that your cable is not reversed.

  Contact the seller if still under warranty for repair.  This could be the hard drive or motherboard and the problem lies the only diagnosis from a repair facility.

• CARD READER USB FOR DESKTOP HP PAVILION 500 - C60?

  I have a new 500 - C60 HP Pavilion desktop computer, but the front card reader does not accept the largest flash Compact Flash (CF) card.  I have an old USB multi-card with four different card slots, which accepts the card see  Would this setting work satisfactorly?

  Thank you

  shamrock838

  Hello @shamrock838,

  I understand that your desktop HP Pavilion 500 - c60 PC does not support the biggest Compact Flash Memory Card and you are curious as to whether or not you can install an USB multicard Reader which accepts the memory card see First of all, you have reason 7 - in1 media card reader did it installed does not supported CF memory card, but it supports the following cards:

  • Digital safe™ (SD)
  • Secure Digital High Capacity (SDHC)
  • SDXC
  • Memory Stick
  • Memory Stick Select
  • Memory Stick PRO
  • Memory Stick MagicGate

  I don't see why you can't connect the 4 - in1 USB multicard reader you have. Until the operating system detects and installs, you should be fine.

  I hope that I have answered your question to your satisfaction. Thanks for posting on the HP Forums. Have a great day!

• Problem using Extract IMAQ. Don't not out two different images

  Hi, I am using the multiple functions of extract IMAQ for some parts of the image of the webcam, then using color extracted from function to get values of RGB. The problem is that two functions extract IMAQ give the same image on its out port. The extract of diagram of block and VI are attached below. Also, please let me know if there is a better way to do this. I need to expand this later to extract parts of the image instead of two different about 40 - 50 RGB values below.

  

  It's happened because IMAQ Images transferred by references. You must provide images of different destination for each extraction:

  

  Andrey.

• The use of two different NICs on the RT?

  Hello world... I am currently working on a project where I have to deal with the problem mentioned in the thread topic: I have a PC with LabVIEW RT which must be able to establish network connections using two different network cards. One will be used to connect via TCP/IP to a host computer that will show you the data transmitted through variables shared; the other communicates with another PC via the Modbus Protocol. The key is that each communication is done through a separate network card.

  So far I could not understand how to set up these two things happen. Does anyone know how to do this? Advice will help you.

  For communication of RT, I use a project of RT standard, with the RT PC, given one of the IPs, and for the part of Modbus, I created a server I/O with a master and a slave. Separately, everything works fine, but when I get them together it does not work.

  Thanks for your help!

  Sorry it took me so long to answer, I've been busy lately... I found a solution to this problem that I mentioned, and just in case anyone has similar problems in the future, I will briefly describe what happened.

  Caseyw suggested, he had to allow both NICs through the measurement and Automation Explorer. The cause of the failure of connections was in fact that I was not using the 'right' for Modbus communication, which was rolled out on the secondary card. The solution was to use the URL Protocol with the correct path in the field, addressing the right IP address. To avoid making this post a mixture of subjects, I do more futher, but I got the gist of it, so if someone has similar problems when I work with multiple network cards or Modbus communication protocols, do not hesitate to contact me, I'll be happy to help you.

  Thank you

• The way of writing to a wireless bridge between two different routers.1:broadband and dir 2:dlink 605 l

  I want to bridge.and wireless I can't do that... Please send me how to write to a wireless bridge between two different routers.

  1:broadband
  and
  2:Dlink dir 605 l,

  Hi Mohammed Ehsan Jourah,.

  Thanks for posting the request in the Microsoft community forums.
  I understand that you need to know how to make a wireless bridge between two different routers

  What version of the operating system is installed on the computer?

  To connect multiple computers, install a network adapter in each and run a network CAT5 cabling to connect each one to a hub (and thus the other.) The computer that will serve as a transition will have a standard network card for wired and a wireless network adapter that will connect to the wireless (WAP) access point or gateway on the second network.

  A network bridge is software or hardware that connects two networks or more so that they can communicate. You can create only a single bridge network on a computer, but a bridge can handle any number of network connections.

  You can try the steps at the bridge between two different routers wireless.
  a. determine the coverage area. When using two or more routers, the coverage area should be divided, and each router should be placed in a central location in each subdivision. If you add a wireless router to an existing network, this may mean moving the first router.
  b. decide which router is the main router. The main router is connected to the Internet, a LAN cable or other networks. It should be as close to the wired network connections or who has the best line of sight to another wireless network. In addition, the main router should be a high range router, allowing large tables of State and more users.
  c. buy a spare antenna, as the antennas that come with most routers do not have very good range. Quality omnidirectional antennas can push the range and signal strength of each of the routers, which, in turn, will reduce the cost by allowing routers less cover more space overall.
  d. deploy the primary router carefully. This router is the most important and requires most of the time of installation and options. Set the WEP (Protocol) encryption Service Set Identifier (SSID) and wireless, set up the Internet connection and test the router with some clients (computers). Once you get the main router deployed, deploy other routers should be easy.
  e. deploy the secondary routers, which must be configured to operate in "mode of transition." Secondary routers should be deployed around the perimeter of a large area or 'hot spots' where users placed - for example, will convene a bench Park or the table.

  Links:
  Create a network bridge:
  http://Windows.Microsoft.com/en-us/Windows7/create-a-network-bridge

  Add a connection to a network bridge:
  http://Windows.Microsoft.com/en-us/Windows7/add-a-connection-to-a-network-bridge

  Hope this information helps you. If you need to get help or information with decision-making wireless bridge between two different routers, I'll be happy to help you.

• Whenever the computer is started, two different styles of start menu appear on the screen, divided vertically from left to right.

  Original title: is this monitor or windows?

  This condition began while I was running xp sp 3.

  I worked in google earth at the time.

  I don't remember exactly what happened.

  But now, every time I start windows, two different styles of the start menu

  appear on the screen, divided vertically from left to right.

  The menu on the right can only be extended to about half of the control panel to the left.

  The menu on the left can grow to the right once the right image has been reduced.

  I tried to reset the start menu in the program settings without success.

  Anyone have any ideas?

  I hope that I was clear enough with this info.

  The article you referred to seems to apply to vista and windows 7.

  How ever, before I received your reply I had already solved the problem myself"

  I appreciate the proposed both help Lisa M and Azeez 'n'

  No further assistance is necessary.

  Thanks again.