PC not picking up the modem

Similar Questions

• HP Pavilion dv7-6c95dx - do not pick up the Samsung 840 Evo SSD for clean installation

  Hello

  Laptop model: HP Pavilion dv7-6c95dx

  I bought a new Samsung 840 Evo 500 GB SSD and going on to replace the main HARD drive. Tried to install Windows 7 Ultimate on it using the USB bootable Win 7, it loads the installation and starts ok and then he asks to load the driver for any device and gives you an analysis of the option to see if there is any storage device to select for installation. It clearly shows that it does not pick up the SSD.

  Unfortunately the bios insydeh20 V3.5 has no possibility of even check if it is detected or so.

  What do you think is the problem? The BIOS update would solve this issue? or is there any other work around that.

  Thank you

  Mike

  Before I went ahead with the method you suggested, I tried updating the Bios with the latest version and voila... system picked up the SSD and all is well now.

  Thank you

  Mike

• Router is not connecting to the modem so I can't get internet

  All right-_ - I tried a lot of things with this so I get irritated sorry. Here is my info I have a Linksys Wireless Router with SpeedBoost Firmware Version 7.2 WRT54GS (latest version). I'm trying to use it with a Sprint 645 series Modem. My IP address when you are connected to the router and the router connected to the Modem is 192.168.1.100 who my ISP said was ok to make it work. While it is just connected to my modem, it's the same thing except replace the 100 by 1. My ISP uses a measure of security where The Thing DHCP is 192.168.1.1 and so is the DNS server and default gateway and im not sure if this has something to do with it. I used the ping at a command prompt to make sure that I am connected to the router when its plugged up and it is. This is a new router. I have internet with Modem just perfectly. I tried to reset the router and that does not work-_-. I don't think it is important more because I tried to fix the many way people have told me and it didn't work, but I'll tell u in any case. When I put up the first router time I hung and lit everything at the beginning. Then I noticed that it says Run CD before to connect the cables... those who were not in the instructions but wtv... anyway resetting should have fixed or so I was told by other people on this forum. I use a laptop with Windows Vista, and I don't have access to a desktop computer in case I need a XD. I can connect to the router fine because I can access the Setup page... and I can connect wireless... The ONLY problem seems to be that the router will not connect to the Modem... for some reason of wtv-_ - I think that its because the entire security measure on the way to the DHCP and the DSN and the bridge are all 192.168.1.1, but that's just me. I'm sorry this is very long but I really want this problem-_ - I had this router for a month and becomes really annoying so please help . My ISP is Embarq. I ran the installation CD and I had all through the last step (standby router) after having connected the power supply to the wall for the router. Just, it is there forever and then says "error: 322 cannot find router or something like that." There are 3 steps to try to fix it. It says to make sure that the router is connected (it is), it is said also to make sure that u does not actually connect your old router, (I don't have a-_-) and then re-run Setup. and by the installer, I mean where u plug in all the cables in the right way. * sigh *.

  If you need anything else please ask.

  Your second post says "" ignore this "so I guess everyone thought that you set..."

  When you connect through your router that you have two instances of DHCP past... one is your DSL modem with router IP address on its WAN interface. The other is the router that gives your computer an IP address via the DHCP server on the router. The IP address of the modem gives your router is in the 192.168.1.0 network. Unfortunately, by default, the reange of Linksys routers LAN IP address is also in this range. For that to work, you must set your router 192.168.2.1 LAN ip, so that the LAN and WAN router interfaces are in different networks.

  To do this, unplug the DSL modem router, power it and your computer, and then connect the computer to the router by an ethernet cable. Turn on the router and the computer, and then go to 192.168.1.1. Change the LAN IP on router 192.168.2.1, save the configuration, and then restart the computer. Once the computer returns to the top, navigate to 192.168.2.1... you should be able to get to the router GUI configuration.

  Turn off the router and the DSL modem, connect the router to the modem via the Internet port using an ethernet cable, and then turn on the modem, then the router... you should be good to go...

• My printer is not picking up the paper from the bin

  My new Officejet 4500 office is not picking up the paper from the bin over. I get the off error paper after he tries and fails to load a sheet of paper. Oops, thread, my bad.

  Hello

  HERE , the info can help.

• Game of demand does not pick up the good period open to active fixed from the SQL statement

  Hello

  We have a demand that could kick off the simultaneous application of the value: Ixr: list of asset by period and Ixr: reserve book report.

  
  

  ON overall demand, we set the parameter: default period based on a SQL = select period_name from FA_DEPRN_PERIODS where book_type_code = 'PER2011' and period_close_date is null

  
  

  The query runs with the good period, until we open the new period, the game application will still come closed period.

  When I run this script on the database, it gives the correct name of the open period.

  
  

  Why all the demand does not pick up the open period?

  
  

  Rock
  

  
  

  Hello

  When planning, the parameter values that you gave when planning will not change.

  For the test, for a simultaneous program, I create a parameter and has given the value 100 tank and default type sql statement and the value as below.

  Select to_char (sysdate, 'dd-mon-yyyy hh24:mi:ss') of double

  If, at the time of the program, it shows a default value such as the date and time with seconds. Then I planned it for every minute.

  When you check in for each race it is seen the first time only, it does not.

  so in your case, you must plan its new after change of period.

  Hope this will help you...

• Portege R200: Sound does not work on the modem

  Does anyone have any suggestions on how I can get sound of my modem?

  I have a laptop Toshiba Portege R200 with Win XP Version 2002 SP2 with a Toshiba Software modem on COM3. When I dial a number with the modem there is no sound, even if the modem work and connect to my server.

  · The sound works for other applications and Windows itself, so I know the speakers work.
  · I moved my hard drive on another laptop and had the same problem, so I know that it's a software issue and not a hardware problem.
  · In Control Panel sounds and peripheral Audio, the volume is set to high and the Volume, phone, Mono control Out and other volume settings are all rich.
  · In the modems Control Panel Options and the modem speaker volume is set to high
  · In the properties of the Modem, it indicates that the device is working properly
  · Through HyperTerminal, I sent the AT & F, ATM2 and ATL3 commands to be sure, has everything been settled properly (and the answer to all was OK)

  Someone at - it see this problem with the modem doesn't do not all sound? Suggestions?

  Thank you!

  Mike

  Hello

  I put t know which sound modem tell you exactly but is it so important to you?
  If the modem works correctly and you can connect to the internet, why you want to have the sound of the modem? Maybe you hear the strange sound of modem that is displayed when the modem tries to build an internet connection.

  You can try to change the numbering in help. Maybe it s in legumes and want to have the tone.
  To do this, you will need to enter in the Control Panel, and then select the modem.
  Please indicate the location on the dialing rules tab, and select Edit.

  You can then change the dial using the general tab.

  It will be useful.

• Reinstalled vista now the modem does not work, says the modem is already in use. Modem does not appear in the material...

  Vista Basic with dial-up. I reinstalled vista and now the modem will not work with any of the numbers given by my provider. He throws error numbers (Sorry didn't write them) and said that the modem is already current usage or other computer is busy. The modem does not appear in the lists of material and reinstallation does not work. The computer does not recognize when a new modem is installed either. I use the same drivers provided with the computer when I got it.

  Hello

  I suggest to refer to this link and follow the instructions in the link below and check, if this can help:

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-modem-problems

  It will be useful.

• TouchSmart HP ENVY 15t with chipset Intel Centrino Wireless N 2230 not picking up the Wireless N

  I just picked up a Touchsmart from HP ENVY 15t and want to connect to wirelessn but he does not see my router n wireless band. I do not however see the Group g. I fiddled with some of the configuration of the pilot, but he has not made a difference. I have a HP Ultrabook job and never had a problem so I know that the router is not serious. BTW, it's a Belkin AC1200 router. I saw drivers updated on the HP website but got some updated of Intels Web site. I can't believe it's a problem. I use to work on network cards, back in the day and it is hard to believe that it would not feature standard/tested. Any thoughts would be GREATLY appreciated!

  Wow this is interesting that Intel comes out there are issues but I applaud on that! I have replace the card and it went well. Hard to get off this part of the front back. Also a few small screws and two tiny wires that must be back in place to the new card. (God miss me the fat old branch PCI cards.)  :-)) So care must be taken with it but other than that worked great.

  I originally had all sorts of problems and I think that it is because in my effort to fix the 2230, I downloaded this bad set of drivers which speak of the previous answer. So I uninstalled the wireless pro software, and then he had automatically detect drivers and he chose an earlier version and then everything worked. I guess that the default windows driver will work, but I think that because I had previously installed, it will not work. If I had to do it over I would have uninstalled the first 2230 (otherwise your new wireless network will be called wi - fi 2) and also the proset wireless software.

  If you uninstall not the 2230 first before Exchange you the card then go to Device Manager and select hidden devices to get rid of him. For reason of removing sound (I think also helped) along with (as I mentioned) the auto detected Intel java plugin detects the old version of the drivers seem to be the thing that finally did it for me. I got around the full bars and the signal strength is phenomenal for 2.4 and 5 ghz bands.

  I've also used these recommended Intel for the card and the router settings

  http://www.Intel.com/support/wireless/sb/CS-030709.htm

  For some reason, my router Belkin necessary WMM enabled for devices to work with these settings. Hope this helps someone...

• BlackBerry Smartphones do not pick up the signal

  Hi there... once my phone is in sos mode is not picking up signal even after beach... I had put my mode 2 g network... s that the reason?

  any response will be appreciated...

  Thank you

  DIEYE

  Hi dinu7272

  Welcome to the community

  You can try a battery pull reboot, but I suggest you contact your Airtel carrier and get a new SIM card. The problem may be in the SIM card.

  KB03448 : network status indicator shows "SOS" on the BlackBerry smartphone.

   

   

   

  Prince

  ______________________________________________________________________

  Click 'Like' If you want to thank someone.

  If problem resolves mark message (s) as a 'Solution', so that others can use.

   

• Installation of Windows 7 does not connect to the modem broadband.

  I installed characteristic of two different versions of Win 7 64 on my desktop at different times.

  The two does not connect to my modem. I get error 651. I've tried everything.

  I have consulted my ISP, checked the provider. The installer works fine with other OS and Win 7 on another computer.

  My office tells me that there is no driver installed. There is no driver to install.

  I need a connection to the firmware in the modem to work, something that seems missing from Win 7 Home Premium 64.
  Your background of catch-22
  LCW

  See this previous post/answer

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/error-651-in-Windows-7/65077414-15f8-450b-BD19-5cce9a57fcf0

  PS after I clean installed did you get your motherboard manufacturer system drivers, if a generic desktop computer, or if from a major manufacturer, for example Dell/HP support site?

• G70 213EM Windows 7 Fax does not connect to the modem

  "Hi, my G70 213EM let me use Windows 7 Fax, when I try to send a fax, it tries to detect the modem (HDAUDIO Soft Data Fax Modem with SmartCP) and reportsan error occurred - try the operation later or contact your system administrator '. He has worked with the release candidate, but not now with Windows 7 Home Premium full version.

  I questioned the modem via Device Manager and obviously only the fault I can see is a line in the newspaper that says ' DSR is low during the initialization of the modem. Verify the modem is turned on ' , but it responds after that? very strange.

  12-01-2009 09:34:12.373 - File: C:\Windows\system32\tapisrv.dll, Version 6.1.7600
  12-01-2009 09:34:12.389 - File: C:\Windows\system32\unimdm.tsp, Version 6.1.7600
  12-01-2009 09:34:12.389 - File: C:\Windows\system32\unimdmat.dll, Version 6.1.7600
  12-01-2009 09:34:12.389 - File: C:\Windows\system32\uniplat.dll, Version 6.1.7600
  12-01-2009 09:34:12.404 - File: C:\Windows\system32\drivers\modem.sys, Version 6.1.7600
  12-01-2009 09:34:12.404 - File: C:\Windows\system32\modemui.dll, Version 6.1.7600
  12-01-2009 09:34:12.404 - File: C:\Windows\system32\mdminst.dll, Version 6.1.7600
  12-01-2009 09:34:12.404 - Modem type: HDAUDIO Soft Data Fax Modem with SmartCP
  12-01-2009 09:34:12.404 - Modem inf path: oem3.inf
  12-01-2009 09:34:12.404 - Modem inf section: ModemX
  12-01-2009 09:34:12.404 - Matching hardware ID: hdaudio\func_02&ven_14f1&dev_5051&subsys_103c360b
  12-01-2009 09:34:12.600 - 115200,8,N,1, ctsfl=1, rtsctl=2
  12-01-2009 09:34:12.600 - Initializing modem.
  12-01-2009 09:34:12.600 - DSR is low while initializing the modem. Verify modem is turned on.
  12-01-2009 09:34:12.610 - Send: AT
  12-01-2009 09:34:12.611 - Recv: OK
  12-01-2009 09:34:12.611 - Interpreted response: OK
  12-01-2009 09:34:12.621 - Send: AT&FE0V1S0=0&C1&D2+MR=2;+DR=1;+ER=1;W2
  12-01-2009 09:34:12.623 - Recv: OK
  12-01-2009 09:34:12.623 - Interpreted response: OK
  12-01-2009 09:34:12.633 - Send: ATS7=60S30=0L2M1+ES=3,0,2;+DS=3;+DS44=3;+IFC=2,2;X4
  12-01-2009 09:34:12.634 - Recv: OK
  12-01-2009 09:34:12.634 - Interpreted response: OK
  12-01-2009 09:34:12.635 - Session Statistics:
  12-01-2009 09:34:12.635 -                Reads : 18 bytes
  12-01-2009 09:34:12.635 -                Writes: 94 bytes
  ATQ0V1E0 - OK
  AT+GMM - +GMM: HDAUDIO Soft Data Fax Modem with SmartCP
  AT+FCLASS=? - 0,1
  AT#CLS=? - COMMAND NOT SUPPORTED
  AT+GCI? - +GCI: B4
  AT+GCI=? - +GCI: (00,01,02,03,04,05,06,07,09,0A,0B,0C,0D,0E,0F,10,11,12,13,14,15,16,19,1A,1B,1C,1D,1E,1F,20,21,22,23,24,25,26,27,28,29,2A,2B,2C,2D,2E,2F,30,31,32,33,34,35,36,37,38,39,3A,3B,3C,3D,3E,40,41,42,43,44,45,46,47,48,49,4B,4C,4D,4E,4F,50,51,52,53,54,55,56,57,58,59,5A,5B,5C,5E,5F,60,61,62,63,64,65,66,67,68,69,6A,6B,6C,6D,6E,6F,70,71,72,73,74,75,76,77,78,79,7A,7B,7C,7D,7E,7F,80,81,82,83,84,85,86,87,88,89,8A,8B,8C,8D,8E,8F,90,92,93,94,96,97,98,99,9A,9B,9C,9D,9E,9F,A0,A1,A2,A3,A4,A5,A6,A7,A8,A9,AA,AB,AC,AD,AE,AF,B0,B1,B2,B3,B4,B5,B6,B7,B8,B9,BA,BB,BC,BD,BE,BF,C1,C2,C3,C4,C5,C7,C8,C9,CA,CB,CC,CD,CE,CF,D0,D1,D2,D3,D4,D5,D6,D7,D8,D9,DA,DB,DC,DD,DE,DF,E0,E1,E2,E3,E4,E5,E6,E7,E8,EA,EB,EC,ED,EE,EF,F0,F1,F2,F3,F4,F5,F7,F8,F9,FA,FB,FC,FE)
  ATI1 - 255
  ATI2 - OK
  ATI3 - SoftK56V_B2.1_V7.80.4.50
  ATI4 - HDAUDIO Soft Data Fax Modem with SmartCP
  ATI5 - 180
  ATI6 - SoftK56
         CModem Version 12
         Rksample Version 342
  ATI7 - 255
  

  I hope someone can help?

  Re-installation of Windows 7 Home Premium 64-bit and let it update seem to have solved this problem, don't know why?

  Thanks for your help anyway.

• WebCenter Navigation | Upper level nodes do not pick up the change of locale

  Hi all
  
  I am facing a problem with the beams of model and default navigation resources in WebCenter. (I tested in PS3 and PS4)
  
  I've implemented a change language menu which changes the settings regional managed user in a bean method. I used beams of resources of high level and the second level pages using the value by defect-navigation - model .xml. Here is my test case.
  
  (1) default application language is English
  Top level 2) as well as its child page is both showing English values (picked up from resource group)
  (3) use a language selector down to change the language of the application in Hindi (I replaced the method of calculateLocale() of CustomViewHandler class to apply this logic)
  (4) the second level in the navigation page begins to pick up the Hindi of resource group value, but the first level page still has the old English value.
  
  Even if I refresh the whole page with F5 or ctrl + F5, the top-level page does not reflect the new language.
  
  Does anyone have an idea why this is happening? I don't do any special implementation for the second level (partial trigger etc.), but what I have to do something for the first level?
  
  Thank you
  Prashant

  Hello.

  You must force to reevaluate the EL Expressions and invalidate cache SiteResources because WebCenter is cached Navigation model.
  The best multilingual for me is based on Phase ADF earpiece to force the phase of "prepareModel" when you change language. PrepareModel phase must invalidate SiteResource cache to force assess the EL Expressions.

  You have a multilingual sample based on ADF Phase listener downloadable here http://danielmerchanoracle.blogspot.com.es/2011/09/multi-lenguaje-en-una-aplicacion-de.html. In addition, it is a long explain on that (but it's in Spanish ;)).

  Blog entry: http://danielmerchanoracle.blogspot.com.es/2011/09/multi-lenguaje-en-una-aplicacion-de.html
  Example of direct download: http://dl.dropbox.com/u/46128268/Oracle%20WebCenter%20Samples/WCPortalTraduccion.rar

  Kind regards.

  Published by: Daniel Merchan on 13-Apr-2012 14:06

• activation, connection Wi - Fi, not picking up the wireless

  can not pick up Wi - Fi, when searching for said wireless network is not enabled

  I need wireless network adapter ITA just trying to get a couple of Dell to tell me what thank you one and

• Why my laptop with bluetooth connected does not pick up the bluetooth on my laptop

  Windows does not detect the bluetooth on my desire to hdc, someone help

  Hi alia 45

  Make sure that Windows is configured to accept incoming Bluetooth connections.

  Step 1
  You can check the compatible devices Bluetooth configuration panel. Here's how:

  1. Click theStart button, select Control Panel , click hardware and sound , and then click Bluetooth devices .
  2. Click theOptions tab, select the allow the devices to connect to this computer check box, and then clickOK .

  If this step does not help, try the next step.

  Step 2

  Remove and then reinstall the device:

  1. click the Start button, select Control Panel , click hardware and sound and then clickBluetooth devices .

  2 Select the device that is not working, and then clickRemove .

  3. click on Add , press the reset button on the unit (or make it discoverable following the manufacturer's instructions), check the boxmy device is set up and ready to be found and then clickNext .

  4. If the device is not found, repeat the previous step. When the device is found, select it, and then clickNext .

  5. follow the remaining instructions in the wizard.

  ·        Make sure that the device is on and that the batteries should be replaced.

  ·        Make sure the Bluetooth adapter for your computer is turned on and that the device is in use and detectable. If you don't know how to turn on discoverability, read the instructions provided with the device or check the manufacturer's Web site.

  The problems with Bluetooth devices
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-Bluetooth-enabled-devices

  Nelex.

• SQL does not pick up the reference sql plan

  Hello

  My version of the database is 11.2.0.03 64-bit quarter computer cart exadata

  I created a base line for an inefficient and then added SQL tips used to fix the plan and the new plan associated with the old plan sql_handle column. I am able to see the two plans (good and bad) present in the table dba_sql_plan_baselines as shown below

  Old
  --------------------------------------------------------------------------------
  Plan name: SQL_PLAN_fgky3z20smxzve27462bc         Plan id: 3799278268
  Enabled: YES     Fixed: NO      Accepted: YES     Origin: AUTO-CAPTURE
  --------------------------------------------------------------------------------
  Modified
  --------------------------------------------------------------------------------
  Plan name: SQL_PLAN_fgky3z20smxzve307ad0f         Plan id: 3808931087
  Enabled: YES     Fixed: YES     Accepted: YES     Origin: MANUAL-LOAD
  --------------------------------------------------------------------------------
  

  When I ask dba_sql_plan_baselines with the signature below is the output

  SIGNATURE SQL_HANDLE                     PARSING_SCHEMA_NAME            ENABLED ACCEPTED FIXED
  --------- ------------------------------ ------------------------------ ------- -------- -----
  16702659115126224891 SQL_e7cbc3f88189f7fb           SSO307010265                   YES     YES      NO    
  16702659115126224891 SQL_e7cbc3f88189f7fb           SSO307010265                   YES     YES      YES   
  

  I then checked gv$ sql and found the signature not displayed in the EXACT_MATCHING_SIGNATURE but the sql_plan_baseline is NULL.

  I'm not able to determine what am I missing.

  Can someone please help

  Thank you

  Jayadeep

  Yes, good point - this can be a factor.

  I noticed something similar once:

  https://OraStory.WordPress.com/2012/03/09/SQL-patch-III-plus-parallel-baselines/

  In this case, the profile of sql and sql patch can be worthy avenue, as mentioned by Lothar.