Photosmart C7280 will print a computer on the wireless network

Similar Questions

• I cannot print to my photosmart C5280 of my laptop computer on the wireless network

  I have a Toshiba L750 running the operating system of Windows 7 32 bit and I am unable to print on my HP Photosmart C5280 printer. The printer is connected to my desktop which works on Windows 7 64 - bit OS with an ethernet cable. The printer works fine from the desktop and the laptop captures the internet wireless via the modem attached to the Office so that the network connection seems to be OK. I am also able to access the shared files on the desktop hard drive of the laptop which again seems to confirm that the network connection is fine. I tried to update the drivers concerned and all seem to be up to date. Previously, I was able to print from the laptop, but for some reason any, that he will no longer work. I have installed the printer software from the original CD supplied with the printer on the laptop to see if that would solve the issue, but nothing helped. I uninstalled from this software. I am at a loss and frustrated. I have also been through the printer Troubleshooter and Microsoft MrFIXIT, to anything will do. Someone out there of the clues as to what could be causing my problem? I might also mention that HP laptop of my son is able to print to this printer without any problems.

  Which, in my view, could have gone, it's that you used on your desktop printer sharing to allow other computers on your home network to access. Here's a video of Microsoft on how you can achieve:

  http://Windows.Microsoft.com/en-us/Windows7/share-a-printer

  Let me know if that solves the problem!

  See you soon!

• HP Deskjet 2540: My printer cannot connect to the wireless network (SSID is not found)

  Hello

  I have a HP Deskjet 2540 printer that is configured to print using the USB cable, and I have no problem printing through it. I just bought a router (D-link DWR116) and I'm trying to set up the connection to the router wireless to my printer. When I use the printer setup & software and select the option "convert a connected USB printer wireless", I can choose to enter into the setting of the printer access the router automatically or manually. These two will come with the same problem where the program is my name SSID of the router successfully but then failed to connect to what the SSID is not found.

  It comes on it comes up with the error message:

  Question: You have manually entered the name of the network (SSID) cannot be found.
  Solution: Check that your wireless router is powered. When to manually enter the name of your network (SSID), make sure you enter exactly including upper and lower case and spaces.
  ============================================================================================

  Which is meaningless because it came with the SSID earlier and I chose what options the wireless network available. I tried to manually enter the SSID, but after entering the password for the router, the same error message appears.

  Help, please.

  Thank you

  In fact, I solved the problem. Something about the wifi light on the printer. It can not be flashing, I don't know what the blue light flashes on the wofo of the printer, but I don't think that it means that the wifi is on.

• Impossible to connect a computer to the wireless network, I would like to first of all the automatic configuration service and I need advice.

  Article 861122 start WZC

  Unable to connect a computer to the network wirelee I firstly the WZC serviceand I need advice. TX

  Hello

  • Are you referring to Wireless Zero Configuration (WZC) Service?
  • What happens when you start the automatic Wireless Configuration Service?
  • You receive an error message?
   
  If you experience problems with the wireless network, reconfigure the Automatic Configuration Wireless for all wireless profiles automatically, click the fix this toolfrom the link below.
  Click run in the file download dialog box, and then follow the steps in this wizard.
  Error message when you try to run the Network Setup Wizard update for Windows XP Service Pack 2, Service Pack 3, or Windows XP Tablet PC 2005 Edition wireless
   
  See also:
  In Windows network connection issues
  http://support.Microsoft.com/kb/313242

• Great printer Officejet 7500 a Format to connect intermittently to the computer via the wireless network

  I have a portable printer Officejet 7500 has recently purchased that I would use wireless.  I have an Apple wireless router and am running Windows 7 on my computer.  The printer and computers individually connect to the network, and there is no problem with the router.  The problem is with the connection between the computer and the printer.  I can print things from my computer by sending a file to the printer, but sometimes it works through printing directly from the software.  I tried to scan my computer and the printer, but get the same error at the same time that there is no communication between the printer and the computer.  I suspect that it is a firewall problem, but do not know how to change the settings to allow this communication to occur.  I have the windows firewall and advanced software protective system, but have disabled the windows shield in this software.  Help?

  First of all, download and run this utility:http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?cc=us&lc=en&jumpid=ex_r4155/hho/ipg/ccdoc/printer_diag/&lang=en&softwareitem=oj-106151-2

  What did he say?

  Just to be clear, that the 7500 a is connected to the Airport via radio, correct (not USB)?

  If so, we will define an external static IP and DNS address for the printer:

  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). Yours is 10.0.1.2 a.200.  We use 10.0.1.220 for your printer.
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
  -Click 'apply '.

  Now, stop the router and printer, start the router, wait, and then start printing.

• 2nd computer on the wireless network will not get on the internet

  my computer is xp my 2nd computer is vista through the wireless receiver dlink615 and dlink. is on the network but will not go to any willing internet change workgroups the same two as said is on network and said to the internet, but where to go to get on it turns at the local level only

  Hello

  Please make sure that your services are working very well and started, has not stopped.
  1 wireless zero configuration
  2 Server
  3 workstation
  4 Netlogon
  You can find these services, start > run > type services.msc then, a window will open, check for these services if they are running, then there should be no problem with internet.
  If all services are working correctly, then give IP addresses to your PC manually according to the parameters provided by your ISP or registration of your ADSL modem.
  Hope this solve your problem...
  Thank you

• HP Photosmart 8000 A809 printer offline connects to the Wifi network

  My printer would sometimes disconnect from wifi, but by turning and the new, would solve the problem.  Now, I can not connect via wifi at all.  Diagnosis plug said: I'm very good signal strength with odds of PASSAGE on everything, no other corresponding network mine.

  Config with the correct network name and an IP address of 10.10.10.125.  I tried the USB connection and then converting to wireless, but establishing assistant gets as much as setting her up and recognizing the device, then I get this msg:

  NON-CONTACTED DEVICE

  The network configuration has been correctly transferred to the device. However, to continue to configure the network device, your Mac must have access to the device. So please make sure that your Mac has access to the network: "JC XXXX" and try again.

  Yet, the report says that I'M connected.  When I try to print something the msg happens "printer is off-line" still the blue light is on, and as I said, all diagnostics PASS.

  I turned everything works, including unplugging the router several times, restart my mac etc.  I'm not missing any software updated.

  I tried the suggestion of hp to put my IP address in my browser to access the Networking tab, but Google Chrome tells me that it can't find the address.

  I also reset the printing system.

  What else can I try to fix this?  Grateful for your suggestions!  Thank you!!!

  Looks like you have problems multiple) a printer goes offline and then b) you can not access the IP address of the printer and c) you get an error saying 'Inaccessible device.'

  What is the Mac version that you use to configure the printer? You're on a VPN or proxy?  Is the printer on the same network as the computer?  You have blinking lights on the printer?

  Here is a very comprehensive document that covers everything you need to do to get the configuration of the printer.  I recommend restoring the printer by default and then try to connect again.  Page 76 of the User Guide talks about what to do if you are unable to access the built-in web server

• HP Officejet will not be connected to the wireless network?

  I have a HP Officejet 6500 wireless which will remain not connected to the network over a half hour or so, max.  My wife runs a laptop XP Pro and I have a Macbook Pro with Snow Leopard.  She NEVER problems printing, but my computer is always looking for the printer unless I re - connect via the wirelss Wizard.  I also use a Westell 327W Versalink router/modem and I have connected my Mac via Bonjour, if that helps.  Any ideas out there?  I even reinstalled the router right next to the printer thinking that may be the issue.  He STILL abandons the connection, but it's funny that my wife's computer is not...

  OK, let's assume that your Mac software is correct for now.  Its probably a good assumption.

  We will define an IP address from the printer.  This can help find the network when he wakes fashion 'sleep':

  We will set an IP address of the printer:

  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). In your case, is that 192.168.1.15 to 192.168.1.47 can use 192.168.1.50
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Let the gateway and DNS white. Click 'apply '.

  Now, stop the router and printer, start the router, wait, and then start printing.

  After that, you will have to redo 'Add printer' using the new IP address.

• Want 5532: Printer cannot connect to the wireless network

  My desire 5532 impossible to connect to the network wireless after upgrading the firmware on the router. When you use the wireless on the printer configuration wizard, it cannot find the router. When I manually enter the SSID router and the password, it remains impossible to connect. It wasn't a problem before. Any help would be appreciated.

  Thank you

  Scott

  After updating firmware on the router makes you hard reset the router to its factory settings. Then reconfigure the router back to your configuration, do not use any file backup right? If this isn't the case, please do it first to get your fixed router. Reset the printer to the network settings, and then try again.

• Photosmart Prem C310 install problem, printer is located on the wireless network but don't see iMac

  Try to install this printer. It works via USB, but when I get to the step of configuring wireless and you're

  said to unplug the USB cable, it gives me the following, not accessible DEVICE... The network configuration has been correctly transferred to the device. However, to continue to configure the network device, your Mac must have access to the device. So please make sure that your Mac has access to the network: "mynetwork" and try again.

  The printer is on the network end def (I can ping ok), but the MAC can not see wireless and wont print. I've seen a few threads with similar issues and they suggest wiring the IP address in the printer setup process, but that does not work for me either. Very frustrating, any help would be great

  It could be disregarded in charge of your router BT of Hello.

  Let's try present first, if:

  1 reboot the router to BT by pulling its plug momentarily.

  2. download and install this: http://support.apple.com/kb/DL907

  3. restart your Mac.

  4 reset the printing system:

  -Go to System Preferences > print & Scan
  -Right (or control) click in the rectangle listing your printers and select Reset Printing System.
  WARNING - This will remove ALL your printers!
  -Select the sign more to add a printer. Select the default tab on the top of the window. Search for the printer, select it, and then beside the dropdown 'Use', select the model of the printer (not AirPrint). Wait for the 'Add' button becomes available. Until it clicks.

• OfficeJet Pro 8600 Print more stuck in the wireless network that

  My windows computer uses XP with SP3.

  I recently installed this new printer / all-in-one. The printer is used in a business office. Earlier in the day, the print function works fine. The function scan and I works pouvons fax direcltly to the computer. I can print from my I phone. But then, without any error message printouts begin to get stuck in printing (QC)

  I can always print from my Iphone and I can always use the other functions (scan & fax). I can print to other printers on network.

  I noticed that hpnetworkcommunicator.exe runs twice in the Task Manager when this happens and I end a session to release sometimes draws. In addition, when this occurs I can restart the computer and which also enables the printer working properly again. When I restart the computer, I'm going to finish the rundll32.exe process I've ever had to do before installation of the new printer.

  I tried the HP print and doctor Scan and everything removed but she recommended that disable the firewall settings. I still have the problem with the firewall disabled.

  Thanks for any help.

  http://support.HP.com/us-en/document/c02817031

  Follow this document, sounds to me like you may have to uninstall/reinstall the printer software. Try reinstalling from the downloaded driver at www.hp.com under Support and drivers/Drivers and software. Good luck!!

• C7180 not found on the wireless network

  We have a Photosmart C7180 was working wonderfully for a few years.  Wireless connectivity is great, even move to a new city/home/internet provider required only run the printer Wireless Setup Wizard, and "poof" things began to print.  So far.

  We got new internet service (new router) and now the printer is not found.  No amount of tweaking seems to be able to get our Mac to see.  We have:

  • Redownloaded and restart the installation of the driver on the Mac.  Connect via USB, it works very well.
  • Rerun Setup wireless network on the printer.  He sees the wireless network and complete Setup.
  • Checked the IP addresses: everything is comfortably accessible 192.168.0.xxx.  The printer, the computer, the router, everything in this range.
  • Connected to the printer in the Mac browser to http://192.168.0.6.  He can be seen and worked with.

  However, when we try to print or run the Mac installer, the printer is not found.

  Help?

  Success! With the help of an old wifi access point on the router and it all works. Same Bluetooth? Thank you!

• HP Laserjet 200 M276 Color MFP: HP Laserjer 200 color than MFP M276 found on the wireless network

  Printer is connected to the wireless network, but cannot be seen by the computers on this network.

  The printer has been installed on my home network for 6 months and works well.  Now it is found on the network.  Power cycle the printer, and he started to work for one night.

  The day after the printer is found on the network by PC, running Windows or Mac 8.1 on the network (under Leopard through Yosemite.

  Reset printer settings by default, in the wireless network data and verified that it is on the network (wireless diagnostics confirm the network name, config, port and switch Diagnostics).  Still cannot be found on the wireless network.  I know that it is on the network, because it can access internet functions.

  Repeated configuration via USB for settings wireless program.  Receive error message indicating the wireless settings have been communicated successfully to the printer, but the printer is not found on the wireless network.

  Not cool.  Looks like I have yet another broken HP printer.  I don't know the process.  I called the warranty and they are sending me a refurb printer.

  Returned to the HP after 10 years.  Looks like it was a mistake.

  Hello

  Try restarting your router by unpluggin power for a while, let him 3 minutes to start and restart the printer.

  Click the icon on the printer wireless - what is the listed IP address?

  Can happen that the intellectual property of the Explorer of your computer?

  You can see any difference after the reboot of the router?

• How to get two laptops to access the wireless network.

  My chip wireless on a Dell Inspiron 1520 laptop (intel pro wireless 3954bg) can find the wireless network if I use Intel Pro software, but Windows cannot find the wireless network. My real growth problem trying to connect a second computer; an IBM T42 think Pad computer to the wireless network, but I get a message that the network is secure, and the second computer keeps trying to acquire an address, but will not acquire an address. He just continues to try to acquire again and again, he can never acquire it. This second computer using Windows to configure the Wi - Fi connection and was working fine until I tried to connect the Dell laptop upward. Then, the IBM laptop cannot acquire an address. I go around and try to understand it. Someone at - it information to solve this problem? Both computers are runing Windows XP Pro SP3. My wireless router is a Belkin54g (F5D7230-4V8000)

  Thanks for any help,

  Btk (billy the kid)

  You can control a with either wireless network adapter software integrated in Windows XP (or WZC Wireless Zero Configuration) or with software provided by the manufacturer of the card (for example, Intel PROSet/Wireless), but not both at the same time.

  Most, but not all, software configuration wireless no Windows is smart enough to disable WZC automatically.

  There are a few sites that offer "safety tips" for wireless networks which includes 'hide' your wireless network by disabling the SSID broadcast.  This is not a good idea and does not, in fact, your wireless security.  See http://blogs.technet.com/b/steriley/archive/2007/10/16/myth-vs-reality-wireless-ssids.aspx if you have disabled broadcast SSID of your router, automatic configuration won't be able to find it.

  I get a message that the network is secure, and the second computer guard trying to acquire an address, but will not acquire an address

  If you have enabled encryption wireless router (a very good idea), you will need to enter the correct password in order to connect a find an IP address. What type of wireless encryption configured on the router?

  This second computer using Windows to configure the Wi - Fi connection and was working fine until I tried to connect the Dell laptop upward. Then the IBM laptop cannot acquire an address.

  You have changed something else.  The idea of a wireless network is to allow multiple computers to connect; connection to a computer shouldn't affect how another computer connects.

  The easiest way is to configure your router to connect a computer using an Ethernet cable (if you connect wireless, you will be disconnected when you make a change to the configuration of the router wireless).  For the Belkin router User Guide is here--> http://cache-www.belkin.com/support/dl/p74559-f_f5d7230-4v8xxx_manual.pdf

  Open a web browser (Internet Explorer, Firefox, etc.) and type 192.168.2.1 in the address box.  You should get to the home page of the router. Click on the "Login" link at the top.  The default password for the router is blank (no password) unless you changed it.

  Click on the link "Channel and SSID" under the heading "wireless" on the left side of the page.

  • Make sure that there is to check the "Broadcast SSID"
  • "Wireless mode" should be "g only" or "fashion g and b" (the latter is necessary only if you have a very old b wireless adapter in one of your computers)
  • I suggest you let off QoS (but click on "more info" or see what says the User Guide)
  • The wireless channel should be 1, 6 or 11.  If you have no difficulties, let him you will find
  • "Protected mode" should be off (but click on "more info" or see what says the User Guide)
  • If you make changes, click on "Apply Changes".

  Click on the 'Security' line under the heading "wireless".  You should be able to see both what type (if any) encryption is configured (64-bit WEP, 128-bit WEP, WPA, or WPA2) and the password (if any).  Unless your computer maps are old, you should use WPA2.  If the adapter in one or more of your computers is too old to be capable of WPA2, use WPA.  Regardless of the bit, WEP length, is easily broken.

• B110A connects to the wireless network but no PC connection

  Hi Forum,

  I just bought a new HP Photosmart B110A printer range. I got set up with my Belkin wireless router. It is successfully connected. I could set up printing webservice as well. The printer is offline and I could also print a document by sending an email to the email address for the printer configuration. This means that the printer is connected to the wireless network and the internet.

  However, I can not connect to this printer from my PC connected to the same wireless netwrok. When I open the HP Solution Center, it displays the message "disconnected wireless.

  When I connect the printer via USB cable, I am able to connect to the PC and impressions as well fire.

  Can anyone help please?

  Kind regards

  Amol

  Download and run this utility: http://h20180.www2.hp.com/apps/Nav?h_pagetype=s-926&h_lang=en&h_client=s-h-e17-1&h_keyword=dg-NDU&jumpid=ex_r4155/en/hho/ipg/forum/network_diag/

  What did he say?