physical switch not able to ping VM

Similar Questions

• Not able to ping from EXSI and NEXUS of EXSI HOST default gateway

  Hello

  In my topology I use 2960 switch thanks to which are connected the my fabric for interconnection and the NEXUS, I am able to ping ESXI switch but when I ping the blade and the Nexus of ESXI HOST, is not ping and also not able to ping default gateway through EXSI.

  I use X Vlan for all devices.

  Please suggest...

  The first thing is to make sure the VLAN ESX is defined from the NETWORK adapter to the router. the 5K the routing in this case? Also the fabric of interconnections and the pool mgmt of blade must be on the same VLAN / subnet. It seems that the FIM is on

  .7/25 and blade MMIC in sur.100/25. They must be on the same subnet. for ESX, please ensure that your vNIC has the VLAN correct represented and that his license.

  Hope this helps,

  David Jarzynka

• Not able to ping VM1 VM2 to

  Hi team,

  I installed VMWare Workstation 9.0.2 baptized as OracleVM1-H (HostName). Later, I cloned it, named as OracleVM2-H (host name).

  Using the IP address I can ping each other. (OracleVM1-H OracleVM2-H to OracleVM1H and OracleVM2H)

  By using the host name I'm not able to ping it.

  Please find the attachment for ifconfig, / etc/hosts O/P.

  Thanks in advance.

  NGO

  OK sorry I didn't see it, your/etc/hosts has no host name you're trying to solve.

  So in the hosts on OracleVM1-h file, you need to add this:

  192.168.12.3 OracleVM2-h

  And the hosts on OracleVM2-h file to add:

  192.168.12.2 OracleVM1-h

  Then, restart your network services.

  Kind regards

  Julien.

• Not able to ping inside the interface from outside

  Hello

  I'm trying to stimulate a new network like the diagram of the topology below:

  Topology

  However, I have a problem:

  ASA:

  I can ping to:

  192.168.200.1 (Site_RTR IP, int fa0/1)

  192.168.200.2 (ASA vlan interface IP, outside interface)

  10.133.95.12 (DC_RTR, int fa0/1)

  10.133.200.1 (ASA vlan interface IP, inside the interface)

  10.133.200.23 (machine)

  The RTR website, I can do a ping to:

  10.133.95.12

  192.168.200.1

  192.168.200.2

  10.133.200.23 (machine)

  but not

  10.133.200.1 (ASA vlan interface IP, inside the interface)

  Question 1:

  It is possible to access / ping back to this address within the IP Interface from outside?

  Question 2:

  As all subnets 10.0.0.0/8 will go through the interface on the outside, however for the internet traffic, out thru interfacera outside 2.

  I haven't set up any nat, is correct to nat all out for outside2?

  NAT (inside outside2) source Dynamics one interface

  Configuration

  Thanks for the help.

  JJ

  Hi JJ,

  If you plan doing a ping within the IP address of the interface, while the traffic is coming from any interface other than inside, you won't able to ping inside the IP address of the interface.

  This is by design, and you cannot change it by any ACL or other settings.

  Thank you
  Ishan
  Please do not forget to select a correct answer and rate useful posts

• vSphere ESXi ssh works, but not able to ping from the inside

  Hey man,

  I have problem with my ESXi 4.1 straing I just fresh installed on workstation 6.5 and assigned IP address. I am able to ping and ssh on my local network (another PC).

  But when I am trying to ping my local gateway of ESXi bash command line, I get the expiration time. Everything works including shared iSCSI and all but vMotion don't work. Is this firewall problem? I don't think that there inbuild firewall in ESXi.

  I am able to ping the local interface IP, but no gateway, see below.

  ~ # ping 192.168.1.1
  PING 192.168.1.1 (192.168.1.1): 56 data bytes

  -ping 192.168.1.1 - statistics
  3 packets transmitted, 0 packets received, 100% packet loss
  ~ # vmkping 192.168.1.1
  PING 192.168.1.1 (192.168.1.1): 56 data bytes

  -ping 192.168.1.1 - statistics
  3 packets transmitted, 0 packets received, 100% packet loss

  Greate that you are to the top and go.

• 6 of VMWare Workstation - not able to connect to my network "physical."

  Hello

  I installed VMWare Workstation 6 on my Windows Vista Sp1 - machine (host).

  With VMWare, I have virtualized a Win 2008 Server. The configuration of the ethernet connection is on "the bridge."

  I a physical NETWORK adapter on the host, which is connects to an Access Point Wireless LevelOne (with built-in switch).

  I am not able to ping to the physical NETWORK card to Win 2008 virtual server. Get an idea what I did wrong?

  Best regards

  Oskar

  • The firewall between the two? Turn them off temporarily.

  • The customer is using DHCP? If so, did he receive an address?

  • Post ' ipconfig/all' of the host AND guest, and the.vmx the file of the client.

  If you found this information useful, please consider awarding points to 'Correct' or 'Useful' responses Thank you!!

  AWo

  VCP/vExpert 2009

• RVL200 ssl vpn, I'm not able to access resources network or ping of the Home Office

  I had installed a Linksys router using port forwarding to allow remote access to the server desktop remotely. I had some problems with it and I've always wanted a vpn connection to the office, but I could not ' operate. So I bought the RVL200 after that I read on it and ssl vpn.

  I have the router installed right after the modem cable to the office. I'm able to hit the external ip address of the House. I have the router to access the Server Active directory for connections. The connection works fine, all the different active directory accounts have access to the vpn through this. I am also able to make administration of the router remotely. I am able to connect to the vpn and get connected virtual passage. The icon in the systray says that everything is good. With all this, I'm not able to ping every address on the remote network. I can't reach all the network resources as \\pdrserver\irms or my print server ip address. I can't use network XP Favorites to find anything on the remote network.

  Someone has an idea what I am doing wrong? I appreciate the help.

  I thought about it. I was using the same IP for the home and office. It was confusing. I changed my IP to another system. Home office and now 12.4.4.X now 11.4.4.X. After that, everything worked as it should. Readers without mapped problem, ping remote computers. I could access the remote print servers. Works well. So make sure that you do not use the same IP addresses on both sides of the VPN.

• I am not able to change my Ip address in ESX 5.0

  I have the team

  I installed esxi5.0 in vmware workstation.

  I added 5 nic cards to my esx server, I chose the specific virtual networks custom.

  I kept 4 nic in vmnet2 (host only) which is 192.168.1.1. network - used for network management/vmotion/virtual metion

  I kept remaining nic in vmnet1 (host only) which is 10.1.0.1 network - used for ISCSI san.

  I was practicalls on my Dvswitch.

  I created a DVswithc and I tried to migrate my standerd switch to DVswith. all of a sudden my network management down I rebooted the server, once he came themanagment ip address has changed to 10.1.0.0 netwok and uplink also changed network adapter that is connected to the 10.1.0.0 network (vmnet1 - host-only)

  I tried manually change Ip address 192.168.1.15 and uplink to (vmnet2) but I'm not able to ping this ip address, and once rebooted the server he is again 10.1.0.0 network.

  Could you please help me change the IP again to 192.168.1.1 network

  check you just cross the port of the network card that you used when installing ESX.

  You can check your port nic "configure management network > network adapters ' location, check this same network adapter that is used when installing ESX.

  If you still facing the same issue only connect a single ethernet port and install ESX and set the static IP address.

  Thank you

  Dietsch

  + 91 9663923458

• Not able to program PXI-2532 switch

  I am not able to program the PXI-2532 switch. We have PXi 1042 q
  Chasis, PXI-8106 microcontroller, PXI-2532 switch connected to TB-2641
  followed by interruption x 264 outside CBS. I am trying to send 400 mv ac ACC
  signal. But could not pass the signal. Not sure where I am
  evil. What is the best way to debug the issue? I have
  attached to the VI that I use.

  Megane,

  What topology are you using?  Looks like you are using 4 x 128 matrix (1 wire)?

  To confirm, it seems that you connect all the reasons on the ground of the anemometer.  Then you connect the cable Signal to switch columns (columns 0 - N) and the Signal of the anemometer to the line (assuming that line 0). If this is the case, then it is logical, the next connect each column (C0) 0 (r0) one line at a time! (ex: c0-> r0 ;))  One thing to note, is that in your program, there is nothing that breaks the connections that have been made before making the next connection, this means that you make the connections and leave them connected.  Therefore, it is very possible that you have more than one column connected to a line.  I suggest that you use the Channel.vi niSwitch disconnect or niSwitchDisconnect all Channels.Vi to break the connections that have been made before making new connection.

  Have you tried to make connections in the Soft Front Panel switch.  This is a nice user interface that will allow you to make connections by clicking and seeing a pattern of connections and connection points.  I suggest that if you have not done aleready to check that everything works with the Soft Front Panel switch.  (Start > all programs > National Instruments > NOR-SWITCH > NI - SWITCH SOFT FRONT PANEL).  There is a very useful document for all the switches and the front switch, which can be found here that I think really help you start: (Start > all programs > National Instruments > NOR-SWITCH > Documentatio > help OR-SWITCH)

  I hope this helps!

• I am not able to switch user... says accounts computer is currently in use and locked

  original title: computer locked :(

  I am not able to switch accounts of users... says the computer is currently in use and locked and any administrator can unlock? How to unlock so I can not on my other user accounts?

  Hi hellfire4,

  ·         You are the administrator of the computer?

  ·         This computer is on a network?

  If this computer is on a network or a domain environment, then you will need to contact the administrator for more help.

  If this isn't the case, then you may need to ask the user who is already connected, turn off the computer. In addition, you can consult this article to disable this option. (If it is not in a network or a domain environment).

  How to enable or disable the CTRL + ALT + DELETE sequence for logging on Windows XP and Windows Vista, Windows 7

• Not able to sign into webcenter content in the portal of physical machine Virtualbox

  Hi all

  I installed the virtual machine Portal webcenter. Everything works fine.

  Only one problem. I am not able to connect to the WCC to the physical computer. Comments page is displayed, but click on login page will badly formed in the url.

  I think it's because of OSH. Anyone know this problem.

  -Hit the url as - ip address of virtualbox/cs = notes of the WCC page

  -Click on the login page url will be like http://webcenter.oracle.local/webcenter/samlits/its?RPID=rp_00001 & TARGET = http://192.168.56.101:80 / adfAuthentication & login = true

  and error saying page is not available.  I think it's because of OSH. How do I solve this problem

  try to change your hosts file in C:\Windows\System32\Drivers\etc this place.

  Add an entry for your IP as below

  198.168.56.101 webcenter.oracle.local

  Try now...

• I use LR on a mac. By developing her photographs, the sliders on the right side - exposure, contrast, shading has disappeared and I am not able to bring them back. That I switch to get them back?

  I use LR on a mac. By developing her photographs, the sliders on the right side - exposure, contrast, shading has disappeared and I am not able to bring them back. That I switch to get them back?

  Control-click on one of the other section in the develop Panel headers (curve tone, Split Toning, retail etc.).  This opens a menu that allow you to re - select this option to display the base Panel you've lost.

• Aggregation of links ESXi requires the configuration of the physical switch?

  Hello

  I have two physical servers that I'll put up with ESXi. Each server has eight physical network cards. My plan is on each server to use:
  -2 management - connected to vSwitch0
  -2 for VMotion - connected to vSwitch1
  -2 for iSCSI - connected to vSwitch2 (I'll use a SAN)
  -2 to access VM network - connected to vSwitch3

  For each pair, a cable should be connected to switch1 and the second would be plugged into switch2.

  The switches are HP A5120 which are stacked into a big switch with RFID. for example I have a 'big' switch which, if one of the two physical switches dies or is turned off, would cause the 'great' switch to lose half of its ports. In this way, all four networks are expected to continue to operate even if a switch "dies."

  All the information I found online said that ESXi can have two physical cards attached to a unique vSwitch and can then do things smart for redundancy (in which case a physical NETWORK card dies) and load balanacing.

  However, while all the guides tell me how to configure it on ESXi, I'm still not sure if I should combine the two cables on the physical switches.

  So, my questions are:

  (1) in order to get the NIC or balancing working in ESXi, redundancy do I have to combine two physical ports that will connect connect two physical ports that connect to the vSwitch?

  (2) with the consolidation of NETWORK cards, I see how to have an active adapter for the management network, and an auxiliary card works fine, but for the iSCSI network, I wouldn't have only two active adapters for double the bandwidth?

  Any ideas would be much appreciated.

  Thank you.

  (1) in order to get the NIC or balancing working in ESXi, redundancy do I have to combine two physical ports that will connect connect two physical ports that connect to the vSwitch?

  No, there is no need to configure etherchannel/LACP but this will depend on the type of load balancing, you click on the ESXi host - if you use by default, you don't need to configure Etehrchannel/LACP since traffic for each virtual network interface will be only com ove a single physical port, but you will always have the reiciliency to the case where if one of the physical NIC fails traffic then released the remaining port

  If you select the hash of the IP load balancing, you must then implement Etherchannel/LACP on your physical switch since traffice can come form any physical port in the team.

  (2) with the consolidation of NETWORK cards, I see how to have an active adapter for the management network, and an auxiliary card works fine, but for the iSCSI network, I wouldn't have only two active adapters for double the bandwidth?

  Onece well once again it will depend on the Load Balancing method, you select, but you will never be able to create links physical ports to get all of the 2 GB =

  I also moved it to a more appropriate forum-

• Mac Pro Dual Quad 3.0 GHz (8 cores - April 2007) not able to run 64 bit comments

  Help, I should be able to do.

  See this thread, because it is a similar issue that only my machine does not all 64-bit indicating my machine does not support hardware virtualization

  http://communities.VMware.com/thread/143298?start=0 & tstart = 0

  Here is what I get:

  * "VT operation is not supported by this VM configuration. " *

  You have configured the virtual machine to use an operating system 64-bit client.  However, this host is not able to run 64-bit virtual machines or virtual computer has 64-bit support disabled.

  + For more information, see http://vmware.com/info?id=152""+ "

  Running on the latest version, but this problem has always been there in previous versions (2.0.5)

  10.5.7 (failed in earlier versions either)

  8 GB ram

  2 TB of storage

  Tried the switch recommended on the config file but nothing.

  Thank you

  You have only one physical processor that implements revision VT VMCS a 7 and another that implements revision VMCS VT 11.  These processors are not compatible for execution of VT.  One processor is family 6 model 15 stepping 7 and the other family 6 model 15 stepping 11.  Intel has released a firmware fix that resolves this problem for the processors that differ only by deepening.  You should check to see if there is an update of the firmware from Apple that contains this fix firmware.

• Norton and 35 of Firefox are not compatible... I ran Norton Live Update... If Norton is up to date. Why am I not able to use my Norton with Firefox toolbar...

  Why am I not able to run my toolbar on Firefox version 35 Norton. I ran Norton Live update... don't give me good results. I have been using an older version of Firefox... Norton is compatible for a while and all of a sudden become compatible... is not acceptable. I don't usually update FireFox immediately due to problems of this kind in the past, but Firefox likes to take over...

  I'm at the point where I feel like forget Firefox and switch him permanently on explore...

  So frustrating.

  I have the same problem. Norton Support just spent 1.5 hours trying to get v35 to accept it is the latest toolbar (v 2014.7.10.12) on my computer that they - Norton - say IS COMPATIBLE WITH the V35. They suggested that I have than uninstall/reinstall Firefox, which I did. It made no difference.