Ping hostname comments resolves to wrong IP

Similar Questions

• Unable to ping IP address / resolve hostnames Win 7 and XP Pro

  My setup is as follows:

  EchoLife HG521 router WiFi - IP address: 192.168.1.1
  Win XP Pro - address IP 192.168.1.3
  Win 7 Home Premium - IP: 192.168.1.4
  Ping 192.168.1.3 to 192.168.1.4 = Request Timed Out
  192.168.1.4 to 192.168.1.3 ping = Destination Host Unreachable
  The use of firewall in KIS2012 - same result with the firewall disabled on both machines.
  Network discovery is on Windows 7 and the relevant services are set to automatic on both machines.
  Router is able to ping both machines.
  Both machines are set to the same workgroup name.
  Please can someone help? Thank you very much

  Hello

  Try the methods below and see if it can resolve the problem.

  Method 1:

  Reset TCP\IP [Transmission Control Protocol of Protocol\Internet]:

  To reset the stack TCP/IP go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself:

  http://support.Microsoft.com/kb/299357

  Method 2:

  Disable the IP helpdesk:

  (a) hold the Windows key and type R, type "services.msc" (without the quotes) and press enter

  (b) scroll down to the IP assistance service, right-click on it and select Properties.

  (c) in the area drop-down list that says "Autoc" or "Manual", set it to disabled and then click 'apply '.

  (d) then click on ""Stop " to stop the service from running in the current session"

  (e) click on OK to exit the dialog box

  Disable IPv6:

  Try to uninstall IPv6 on all interfaces, the removal of virtual cards of IPv6 and reset the TCP/IP stack.  To remove the IPv6, go to the properties for each network adapter, and deselect the check box next to the Protocol "Internet Protocol version 6 (TCP/IPv6), which will turn off, or select it and click on uninstall which will remove off the computer."  Then go into Device Manager and remove any 4to6 adapters, adapters miniport WUN or tunnel adapters.

  NOTE:

  You should do this for each network connection.

  Disable the DHCP Broadcast Flag:

  Link:

  http://support.Microsoft.com/default.aspx/KB/928233

  Important:

  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  http://support.Microsoft.com/kb/322756

  See also:

  How to troubleshoot connectivity TCP/IP with Windows XP

  http://support.Microsoft.com/kb/314067

• RV180W ping hostname between VLAN & different subnets

  Hello

  I had a RV180w with 1.0.3.10 closes. According to the name of position, I'm not able to resolve host names between different VLANS which affected to different subnets, for example, allows said I have the following hosts:

  CASA:

  192.168.241.100/25 (wired - VLAN 1)

  Router: 192.168.241.1

  DNS: 192.168.241.1

  XBMC: 192.168.242.100/25 (Wi - FI - VLAN 2)

  Router: 192.168.242.1

  DNS: 192.168.242.1

  If I try to ping from two sources to one of the two destinations, the only one I get is a message 'impossible '.

  Authorized additional information routing between vlans & proxy DNS and if I try to look at the hostname under the 'nslookup' command, I could not resolve the host name, but if I do a "ping - a 192.168.241.100 ' it is said ' response from CASA (192.168.241.100) blah blah blah."

  So what I'm missing here?

  Hi Bruno, you can usually solve different subnet host name because the host does not know the subnet that treats it as a security measure.

  Disable the firewall feature on your computers and which must fix, otherwise you will probably have to change the lmhost files.

  -Tom
  Please mark replied messages useful

• Cannot open websites, error DNS when the ping command cannot resolve the name

  Cannot open all websites on a PC. (other computers on the network can access the sites without a problem)
  Error message is "Internet Explorer cannot display webpage."

  I can ping (internal and external) of the IP and gateway addresses.
  Ping translates:
  C:\>ping www.yahoo.com
  Ping request could not find host www.yahoo.com. Please check the name and try again.

  Nslookup translates:
  C:\>nslookup www.yahoo.com
  Can not find the name of the server for the address 192.168.0.1: non-existent domain
  Default servers are not available
  Server: unknown
  Address: 192.168.0.1

  Non-authoritative answer:
  Name: www-real.wa1.b.yahoo.com
  Address: 69.147.76.15
  Alias: www.yahoo.com, www.wa1.b.yahoo.com

  Pathping translates:
  C:\>Pathping www.yahoo.com
  Unable to resolve target system name www.yahoo.com.

  The problem occurs on a wired and wireless connection.
  Reset TCP/IP via netsh int ip reset c:\ressetlog.txt results in the following in the log file error message:

  discount Linkage\UpperBind for USB\VID_0B05 & PID_1723\5 & 2461925A & 0 & 5.  incorrect value was:
  REG_MULTI_SZ =
  SymIM

  Is there a total of 9 errors in the log similar to the one above.
  The host file has only 127.0.0.1 in there.
  Clearing the cache of the arg, flushing the DNS and do a repair on the network connection does not resolve the problem.
  Install a new network device does not resolve the problem.
  I also deleted all the antivirus software and security, including firewalls.
  The Windows Firewall is disabled.
  Boot in safe mode with Networking does not solve the problem.
  Running Winsockfix does not solve the problem.
  Internet Explorer 8 (reset web settings has been done)
  Windows XP Media Center with SP3
  Execution of the IE Diagnostics results in an error 12007 the server name or address cannot be resolved.

  Get the end of the line...

  Any other ideas?

  Thank you

  Larry

  Sorry for the late reply, but I did not have access to the MS Web site for a few months.

  I tried your suggestions, they do not work.

  The resolution is to do a repair of the operating system out of the CD.  Who cleared up the problem.

  Thank you

  Larry

• Cannot ping hostname IB gateway

  Hello

  I installed virtual PeopleSoft HCM Image 9.2.012 on my laptop, with PeopleTools 8.54.08.

  I IB Gateway URL as http://hcmdmo.ps.com:8000/PSIGW/PeopleSoftListeningConnector , because I created this hostname during the configuration of the Virtual Machine.

  Now when I ping the gateway, a new popup window with the message "server not found".

  But if I change the URL to http://192.168.56.101:8000/PSIGW/PeopleSoftListeningConnector, then it shows as active gateway.

  Please help me solve the problem. How I can ping the gateway with the host name?

  Thank you and best regards!

  Add the name to your hosts file.  On windows, which would be in C:\Windows\System32\drivers\etc\hosts

  you add:

  192.168.56.101 hcmdmo.ps.com

• PowerCLI Invoke-VMScript re - ip guest - how to get the variable hostname comments

  I run the following script as a task Post-Power-we a re - ip our VMs after that MRS. them rocking.  I was able to run this script successfully without the variable hostname of comments (in the test, he runs a script by test VM with the hostname assigned...), but I'm stumped on how to get comments variablized according to the machine's host name works on, it will take the host name and use it in the GuestUser variable and the command - VM.  I tried the bold part, but it does not work.

  $srv = Connect-VIServer 10.0.0.10 - administrator of the username-password password

  $Hostname = (get-wmiobject win32_computersystem). Name

  $script = "%windir%\system32\cmd.exe/c c:\dr\drIPsettings.bat".

  $HostUser = "root".

  $HostPassword = "password"

  $GuestUser = ' $Hostname\Administrator '.

  $GuestPassword = "password"

  $ScriptType = "bat".

  SE connect-VIServer 10.0.0.10 - Session $srv. SessionID

  Invoke-VMScript - ScriptText $script - VM $Hostname - HostUser $HostUser - HostPassword $HostPassword - GuestUser $GuestUser - GuestPassword $GuestPassword - ScriptType $ScriptType

  Thank you!

  How you code the - VM on the Invoke-VMScript cmdlet parameter, it seems that Displayname of the guest is the same as the host name.

  Can't you just use a loop on guests and then use the displayname property

  $script = "%windir%\system32\cmd.exe /c c:\dr\drIPsettings.bat"
  $HostUser = "root"
  $HostPassword = "password"
  $GuestPassword = "password"
  $ScriptType = "bat"
  
  Get-VM | %{
     $GuestUser = $_.Name + "\Administrator"
     Invoke-VMScript -ScriptText $script -VM $_ -HostUser $HostUser -HostPassword $HostPassword -GuestUser $GuestUser -GuestPassword $GuestPassword -ScriptType $ScriptType
  }
  

  You can encode the Get - VM with more specific selection criteria or use a Where-Object after the Get - VM.

  ____________

  Blog: LucD notes

  Twitter: lucd22

• Host Windows 7 - unable to Ping WinPE comments

  I installed VMware Server 2 on 64-bit Windows 7 RC1.  I want to use WinPE to a predefined image to an XP machine on the guest virtual machine but it keeps failing.  It seems that comments from WinPE can contact servers and other physical computers on the network (for example, Ping) but these same servers etc could not contact the return in the same way.

  I put the bridged networking and the guest operating system is picking up an IP address for the PXE boot and WinPE.  I uninstalled all the programs Microsoft Virtual PC as has been suggested in a post on this site.

  Can anyone help at all?  I have searched through the forum, but could not find something that works so far.

  Thank you

  Maybe firewall sounds associated with possibly on the host or the guest since WinPE has the default firewall.

  Guy Leech

  VMware vExpert 2009

  ---

  If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

• Import from Erwin 7.3 updates column comments in the wrong section

  There is a bug with importing Erwin. Comments of the column are not placed in the comments section of RDBMS, they are put in the regular comments section so when exporting to DDL, they do not put in the database. We want comments in the database and Erwin here as a section for comments. Anyone know a way around this? Or can it be fixed in the next version?

  Hello

  There is a transformation that can be used for this - look at "tools > design rules > Transformations"-he is named "copy comments on comments in RDBMS.

  Philippe

• To access Hotmail, get comment: something was wrong and we cannot connect you right now. Please try again later. Thank you.

  It happened all of a sudden. After that, I reset the computer to an earlier date. Has not fixed the problem. I rebooted the Internet explorer, Version 8. Has not fixed the problem. I can access Hotmail from another computer without problem. I think that I changed something in the tools that could have caused the problem. All the patches and virus checking are up-to-date.

  Appreciate any help you can provide.

  Don Patterson

  I had a similar problem. I could access Hotmail, but not of pleats. I use 17.0.1 Firefox as my browser and tried IE and no problem with Hotmail. I had to uninstall Firefox and reinstall, and then it worked fine.

• Has not invited ping

  I am a total newbie to VMWare.  I installed VMWare Server 2 on a Windows XP host and configure a virtual machine with a virtual network of NAT.  I installed Ubuntu 9.04 on my new virtual machine.  In the Ubuntu prompt, I can nslookup hostname of the host and get ip address.  I can ping the host by its ip address, but not hostname.  (This seems odd.  If nslookup can find the ip address of the host, why can't ping?)

  The XP client, nslookup can't find an ip address for the host (raised by host name).  And I cannot ping by hostname prompt.   I don't know what ip address to use to try to ping the virtual computer.  I tried a few ip addresses that I found, especially in the "Virtual Network Editor", but none worked (such as ping destinations).

  The first thing to do, I guess, is to make sure if ensure that the host cannot really ping guest - to make sure I have tries the right ip address right.  So where should I look for this?

  If I try to the right ip address, then I guess I need some ideas as to why the host cannot see the comments.  I noticed that the /etc/inetd.conf file is 0 bytes long.  That looked like not promising, but I'm not sure.

  Thanks in advance for your suggestions.

  JMNorris

  Welcome to the forums!

  JMNorris wrote:

  I am a total newbie to VMWare.

  No problem, everyone was, once...

  I installed VMWare Server 2 on a Windows XP host and configure a virtual machine with a virtual network of NAT.  I installed Ubuntu 9.04 on my new virtual machine.  In the Ubuntu prompt, I can nslookup

  host name and obtain the ip address of the host.  I can ping the host by its ip address, but not hostname.  (This seems odd.  If nslookup can find the ip address of the host, why can't ping?)

  If nslookup works, it shows that some DNS server (or the file/etc/hosts) could be contacted to get the name of intellectual property. The reason you can't ping name could be that nslookup has used another server which is configured in the TCP/IP settings DNS.

  The XP guest...

  The guest is XP or Ubuntu?

  ..., nslookup can't find an ip address for the host (raised by host name).  And I cannot ping by hostname prompt.   I don't know what ip address to use to try to ping the virtual computer.  I tried a

  a couple of ip addresses, I found, in particular the "virtual network Editor", but none worked (such as ping destinations).

  For the guest chef resolved name you need a DNS or "/ etc/hosts" or "\windows\system32\drivers\etc\hosts" entry. Suppose you have one, that it will be something like "192.168.x.y", because the customer is using NAT, which means that the customer is part of a virtual network called VMnet8 with his own IP subnet range. The host must be able to ping the guest by this IP address as the host knows this network. Hosts on the physical network will not be able to ping that comments for this reason and because the guest is hidden behind a NAT device provided by VMware.

  Have you tried to enter 'ifconfig - a' in the comments, get IP address and ping from the host?

  AWo

  VCP / VMware vEXPERT 2009

• Cannot access a Web site, but can ping IP addresses on the internet

  -With the help of Vista SP2 64-bit on laptop faulty.

  -Number of computers on the same network have access to the internet.

  -Tried several network interfaces on this laptop, but no luck for access to the network, wired or wireless

  -From this notebook, I can ping addresses Internet IP so the problem seems to be the side DNS.

  -Flushing DNS cache and reset the network interface.

  -Rebooted several times.

  What did I miss?

  Thanks in advance

  Hey easternguy,.

  Check if you can test the Web site by name.

  To do this:

  a. Click Start and type cmd.

  b. press ENTER.

  c. type the following command:

  ping hostname

  Ping uses name resolution to resolve a computer by IP address name. Therefore, if you successfully ping the IP address but you cannot ping a computer name, there is a problem with host name resolution, and no network connectivity.

  Case 1: If you can not ping the Web site using its address, follow these steps.

  In this case, try changing your host file.

  In the C:\Windows\System32\Drivers\etc Hosts files may be damaged or corrupted.

  Review the contents of your HOSTS file and compare it to the screenshot below. There is no need to worry about any line that starts with a # is ignored by Windows. In addition, the line "127.0.0.1 localhost" can be ignored without risk, because it is a standard input.

  

  Everything that appears in your HOSTS file without a # earlier this year, aside from the "127.0.0.1 localhost" line, should be regarded with suspicion when we try to diagnose the cause of the problem. The fastest way to test the involvement of HOSTS file is to just rename the host file. By changing the name of the HOSTS file, prevent us Internet Explorer to use it and so all problems caused by the file.

  Case 2:

  If you can ping external websites by IP address and name, but can't browse the web, probably your browser is misconfigured.

  Check that you do not have an incorrect Proxy Server affected necessary or not.

  For Internet Explorer, follow these steps.

  a. open Internet Explorer.

  b. go to Tools / Internet Options.

  c. click on the Connections tab.

  d. click the LAN Settings button.

  "e. uncheck both" "automatically detect settings" and "use a proxy server for your LAN '.

  This should be it.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Can browse quote but cannot have their ping, apps can't access the internet

  Hello

  I'll do my best to give a full description. I'm sorry if I include irrelevant information, but I don't want to leave anything out.

  I tried to connect my Macbook Pro (with El Capitan installed) 2012 raspberry Pi 2 via ethernet and access it through a web browser. He has failed. It was my first time using an ethernet adapter to crush on my Macbook Pro. Since then, any application that accesses to the internet does not (for example, Appstore, steam, Spotify, Google Drive). Again, however, I can access websites through a web browser. Also, when I try to ping from a Web site via the terminal like Google, it says "ping: could not resolve google.com: Unknown host" even if I can access via a browser. I have tried to disable the firewall and have even reinstalled El Capitan. In addition, internet via the browser if possible access is slower then usual. I am at a complete loss and would appreciate greatly any help.

  Please read this message before doing anything.

  This procedure is a diagnostic test. It is unlikely to solve your problem. Don't be disappointed when you find that nothing has changed after you complete it.

  The test is intended to determine if the problem is caused by a third-party software that loads automatically at startup or logon, by a device, by a police conflict or corruption of system files or some system caches.

  Disconnect all devices wired except those required to test and remove all the expansion cards from secondary market, as appropriate. Start in safe mode and log on to the account of the problem.

  Note: If FileVault is enabled in OS X 10.9 or an earlier version, or if a firmware password is defined, or if the boot volume is a software RAID, you can not do this. Ask for additional instructions.

  Safe mode is much slower to boot and run as normal, with limited graphics performance, and some things work at all, including an audio output and a Wi - Fi connection on some models. The next normal boot can also be a bit slow.

  The login screen is displayed even if you usually connect automatically. You need your password to log on. If you have forgotten the password, you will have to reset it before you begin.

  Test in safe mode. Same problem?

  After testing, restart as usual (not in safe mode) and make sure you always have the problem. View the results of the test.

• Windows Server 2008 Standard: Several concerns: update group policy inconsistent on client PC, frequent disconnections of readers of card and the remote connection

  Hi This is my first time to ask a question here, in this community.

  I'm a sysadmin here at my job and we have some problems on some servers that we are dealing with. Network in our office is stable and we have determined that this is not a problem on the connection.

  • First number - one of our domain controller constantly falls on our directory server and saying that it is not available.
  • Second edition - unable to ping hostname but IP address works very well. (Sometimes the host name is ok, but very intermittent)
  • Third question - connection is unstable card readers causes disconnect

  If anyone can provide any assistance in this respect, it would be a great help.

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• BBM BBM change group Icon in BBM10.8.5.15

  Is there a way to change the Group BBM icon after it's been created?

  I'll assume that you are referring to the avatar of group that displays at the top left of the screen to group chat.

  Yes.  There are several ways to do it, it's more easy for me.

  Open the group or the group chat.  Tap the avatar - this brings you to the info of the group.  Tap the avatar again.  This brings you to a screen where you can select the default icons or click 'Add an image' on the bottom bar. This will bring you to the photos app where you can choose from one of your images as when you add a photo to a contact.

  Note that if you are a group administrator, you will change the avatar for everyone in the group.  If you are not an administrator, you can always change the avatar, but the change will be visible only to you.

  I found it very convenient when I am in two different groups with avatars that are too similar, and made a comment in the wrong group.  I changed the two (at my end) to be radically different.  No more problems.

  I hope this helps.

• Keep exit status listener on the change, but watch without any error

  Hello

  I once again re installed oracle grid. Through the status of the listener, I find that the status of the listener is evolving with different outputs.

  In the first when I typed lsnrctl status then it's what he showed: -.

  [grid@example ~] $ lsnrctl status

  LSNRCTL for Linux: Version 11.2.0.1.0 - Production on 4 February 2015 10:29:05

  Copyright (c) 1991, 2009, Oracle.  All rights reserved.

  Connection to (ADDRESS = (PROTOCOL = tcp)(HOST=) (PORT = 1521))

  STATUS of the LISTENER

  ------------------------

  Alias LISTENER

  Version TNSLSNR for Linux: Version 11.2.0.3.0 - Production

  Start date February 4, 2015 08:59:42

  Uptime 0 days 1 hour 29 minutes 23 seconds

  Draw level off

  Security ON: OS Local Authentication

  SNMP OFF

  Parameter Listener of the /u01/app/11.2.0/grid/network/admin/listener.ora file

  The listener log file /U01/app/grid/diag/tnslsnr/example/listener/alert/log.XML

  Summary of endpoints listening...

  (DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = EXTPROC1521)))

  (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=example.com) (PORT = 1521)))

  Summary of services...

  Service "Orcl" has 1 instance (s).

  Instance "Orcl", State LOAN, has 1 operation for this service...

  Service 'OrclXDB' has 1 instance (s).

  Instance "Orcl", State LOAN, has 1 operation for this service...

  The command completed successfully

  Once again, after waiting a few minutes, I checked again the status of the listener, then it's what she showed.  It shows now the Instance "Orcl", BLOCKED status

  
  

  [grid@example ~] $ lsnrctl status

  LSNRCTL for Linux: Version 11.2.0.1.0 - Production on 4 February 2015 10:31:24

  Copyright (c) 1991, 2009, Oracle.  All rights reserved.

  Connection to (ADDRESS = (PROTOCOL = tcp)(HOST=) (PORT = 1521))

  STATUS of the LISTENER

  ------------------------

  Alias LISTENER

  Version TNSLSNR for Linux: Version 11.2.0.3.0 - Production

  Start date February 4, 2015 08:59:42

  Uptime 0 days 1 hour 31 min 42 s

  Draw level off

  Security ON: OS Local Authentication

  SNMP OFF

  Parameter Listener of the /u01/app/11.2.0/grid/network/admin/listener.ora file

  The listener log file /U01/app/grid/diag/tnslsnr/example/listener/alert/log.XML

  Summary of endpoints listening...

  (DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = EXTPROC1521)))

  (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=example.com) (PORT = 1521)))

  Summary of services...

  Service "Orcl" has 1 instance (s).

  Instance "Orcl", LOCKED status, has 1 operation for this service...

  The command completed successfully

  Once again, after waiting a few minutes, I checked again the status of the listener, then it's what she showed.  It now shows the Instance "Orcl", status RESTRICTED

  [grid@example ~] $ lsnrctl status

  LSNRCTL for Linux: Version 11.2.0.1.0 - Production on 4 February 2015 10:31:36

  Copyright (c) 1991, 2009, Oracle.  All rights reserved.

  Connection to (ADDRESS = (PROTOCOL = tcp)(HOST=) (PORT = 1521))

  STATUS of the LISTENER

  ------------------------

  Alias LISTENER

  Version TNSLSNR for Linux: Version 11.2.0.3.0 - Production

  Start date February 4, 2015 08:59:42

  Uptime 0 days 1 hour 31 min 54 s

  Draw level off

  Security ON: OS Local Authentication

  SNMP OFF

  Parameter Listener of the /u01/app/11.2.0/grid/network/admin/listener.ora file

  The listener log file /U01/app/grid/diag/tnslsnr/example/listener/alert/log.XML

  Summary of endpoints listening...

  (DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = EXTPROC1521)))

  (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=example.com) (PORT = 1521)))

  Summary of services...

  Service "Orcl" has 1 instance (s).

  Instance "Orcl", RESTRICTED status, has 1 operation for this service...

  The command completed successfully

  After a few minutes back I rechecked the status and now it shows nothing: -.

  [grid@example ~] $ lsnrctl status

  LSNRCTL for Linux: Version 11.2.0.1.0 - Production on 4 February 2015 10:31:20

  Copyright (c) 1991, 2009, Oracle.  All rights reserved.

  Connection to (ADDRESS = (PROTOCOL = tcp)(HOST=) (PORT = 1521))

  STATUS of the LISTENER

  ------------------------

  Alias LISTENER

  Version TNSLSNR for Linux: Version 11.2.0.3.0 - Production

  Start date February 4, 2015 08:59:42

  Uptime 0 days 1 hour 31 min 38 s

  Draw level off

  Security ON: OS Local Authentication

  SNMP OFF

  Parameter Listener of the /u01/app/11.2.0/grid/network/admin/listener.ora file

  The listener log file /U01/app/grid/diag/tnslsnr/example/listener/alert/log.XML

  Summary of endpoints listening...

  (DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = EXTPROC1521)))

  (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=example.com) (PORT = 1521)))

  The listener supports no services

  The command completed successfully

  So in short here put it: -.

  FIRST EXIT

  Summary of endpoints listening...

  (DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = EXTPROC1521)))

  (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=example.com) (PORT = 1521)))

  Summary of services...

  Service "Orcl" has 1 instance (s).

  Instance "Orcl", State LOAN, has 1 operation for this service...

  Service 'OrclXDB' has 1 instance (s).

  Instance "Orcl", State LOAN, has 1 operation for this service...

  The command completed successfully

  SECOND RELEASE OF THE STATUS OF THE LISTENER

  Summary of services...

  Service "Orcl" has 1 instance (s).

  Instance "Orcl", LOCKED status, has 1 operation for this service...

  The command completed successfully

  THIRD EXIT OF THE LISTENER STATUS

  Summary of services...

  Service "Orcl" has 1 instance (s).

  Instance "Orcl", RESTRICTED status, has 1 operation for this service...

  FOUR OR THE LAST EXIT OF THE STATUS OF THE LISTENER

  Summary of endpoints listening...

  (DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = EXTPROC1521)))

  (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=example.com) (PORT = 1521)))

  The listener supports no services

  HERE IS THE RESULT OF THE HOSTNAME

  NOTE: ping hostname tells a different IP in the budgetary balance real ip given on the host name is 192.168.0.1

  [grid@example ~] $ ping hostname

  PING hostname.com (69.43.160.216) 56 (84) bytes of data.

  64 bytes of 69.43.160.216: icmp_seq = 1 ttl = 44 time = 337 ms

  64 bytes of 69.43.160.216: icmp_seq = 3 ttl = 44 time = 335 ms

  ^ C

  -hostname.com ping statistics-

  4 packets transmitted, 2 received, 50% packet loss, time 3899ms

  RTT min/avg/max/leg = 335.532/336.382/337.233/1.029 ms

  [grid@example ~] $ ping example.com

  PING example.com (192.168.0.1) 56 (84) bytes of data.

  64 bytes of example.com (192.168.0.1): icmp_seq = 1 ttl = 64 time = 0,033 ms

  64 bytes of example.com (192.168.0.1): icmp_seq = 2 ttl = 64 time = 0.035 ms

  64 bytes of example.com (192.168.0.1): icmp_seq = 3 ttl = 64 time = 0.038 ms

  64 bytes of example.com (192.168.0.1): icmp_seq = 4 ttl = 64 time = 0.038 ms

  HERE IS THE OUTPUT for sqlnet.ora, listener.ora, tnsnames.ora

  [grid@example admin] $ listener.ora more

  listener.ora # Network Configuration file: /u01/app/11.2.0/grid/network/admin/listener.ora

  # Generated by Oracle configuration tools.

  LISTENER =

  (DESCRIPTION_LIST =

  (DESCRIPTION =

  (ADDRESS = (PROTOCOL = CIP)(KEY = EXTPROC1521))

  (ADDRESS = (PROTOCOL = TCP)(HOST = example.com) (PORT = 1521))

  )

  )

  ADR_BASE_LISTENER = / u01/app/grid

  ENABLE_GLOBAL_DYNAMIC_ENDPOINT_LISTENER = ON # line added by Agent

  [grid@example admin] $ more sqlnet.ora

  sqlnet.ora # Network Configuration file: /u01/app/11.2.0/grid/network/admin/sqlnet.ora

  # Generated by Oracle configuration tools.

  NAMES. DIRECTORY_PATH = (TNSNAMES, EZCONNECT)

  ADR_BASE = / u01/app/grid

  [grid@example admin] $ more tnsnames.ora

  tnsnames.ora # Network Configuration file: /u01/app/11.2.0/grid/network/admin/tnsnames.ora

  # Generated by Oracle configuration tools.

  ORCL =

  (DESCRIPTION =

  (ADDRESS_LIST =

  (ADDRESS = (PROTOCOL = TCP)(HOST = example.com) (PORT = 1521))

  )

  (CONNECT_DATA =

  (SERVICE_NAME = orcl)

  )

  )

  [grid@example admin] $

  Hello

  Sorry can't answer you earlier. I have soved the issue of the listener. In fact, there were two issues one of them was the problem of the LISTENER and the other was the following: -.

  SQL > startup

  ORA-01078: failure in the treatment of system settings

  LRM-00109: could not open the parameter file ' / u01/app/oracle/product/11.2.0/db_1/dbs/initorcl.ora'ORA-01078:

  First of all, I solved the ORA-01078: LRM-00109: deliver and then I went to solve the problem of the LISTENER. Here is how I solved the problem LISTNER. It now displays the stable state. It does not change like the one I mentioned above: -.

  [grid@example ~] $ cd $ORACLE_HOME/network/admin

  [grid@example ~] $ cd /u01/app/11.2.0/grid/network/admin/

  [grid@example admin] $ [grid@example admin] $ ls-l

  Total 24

  -rw - r - r - 1 grid oinstall 166 6 Feb 10:06 listener15020610AM0614.bak

  -rw - r - r - 1 grid oinstall 436 6 Feb 10:11 listener.ora

  drwxr-xr-x 2 grid oinstall 4096 2 February 14:16 samples

  -rw - r - r - 1 grid oinstall 205 11 May 2011 shrept.lst

  -rw - r - r - 1 grid oinstall 202 6 Feb 10:09 sqlnet.ora

  -rw - r - r - 1 grid oinstall 322 6 Feb 10:07 tnsnames.ora

  [grid@example admin] $ rm - rf *.ora

  NETCA $ [grid@example admin]

  Configure the listener again

  Set up the Configuration of the Local Network Service name

  lsnrctl stop $ [grid@example admin]

  lsnrctl start $ [grid@example admin]

  [grid@example admin] $ lsnrctl reload

  RESTART THE PC

  Connect as a user of network and wait a few minutes... And then check the status... Its not working now, and displays the output of status statble: -.

  [grid@example admin] $ lsnrctl status

  LSNRCTL for Linux: Version 11.2.0.3.0 - Production on February 6, 2015 11:20:09

  Copyright (c) 1991, 2011, Oracle.  All rights reserved.

  Connection to (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST=example.com) (PORT = 1521)))

  STATUS of the LISTENER

  ------------------------

  Alias LISTENER

  Version TNSLSNR for Linux: Version 11.2.0.3.0 - Production

  Start date February 6, 2015 10:19:34

  Uptime 0 days 1 hour 0 minutes 35 seconds

  Draw level off

  Security ON: OS Local Authentication

  SNMP OFF

  Parameter Listener of the /u01/app/11.2.0/grid/network/admin/listener.ora file

  The listener log file /U01/app/grid/diag/tnslsnr/example/listener/alert/log.XML

  Summary of endpoints listening...

  (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=example.com) (PORT = 1521)))

  (DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = EXTPROC1521)))

  Summary of services...

  Service '+ ASM' a 1 instance (s).

  Instance '+ ASM' READY State, has 1 operation for this service...

  Service "Orcl" has 1 instance (s).

  Instance "Orcl", State LOAN, has 1 operation for this service...

  Service 'OrclXDB' has 1 instance (s).

  Instance "Orcl", State LOAN, has 1 operation for this service...

  The command completed successfully

  [grid@example admin] $