PIX 501 basic Config
I'm putting in place an internet service for some members of the service here in Afghanistan. We use the commercial internet (provided by satellite) to a modem that goes into my firewall 501 pix.
Service that we bought gives us Ip 29, and now I just have it set up as such.
Modem gateway: 10.124.48.1
Outside the firewall: 10.124.48.2
Inside the firewall: 192.168.1.1
Global NAT pool: 10.124.48.3 30 (the rest of intellectual property s that are outside the package)
On the inside of the pool of the host: 192.168.1.2 -.33
DNS for inside customers: 192.168.130.30,.50
Everything seems ok, as I use the PDM software to allow all traffic ip from outside to inside (I know it isn't the safest to do thing ~ and the fact that I turned a firewall $ 700 to a router for $40). I can browse the internet, but it is really weird.
I.E.
I can ping msn.com and www.msn.com , and it resolves the twice,
But if I put msn.com in Internet explorer, it says cannot display the page, but if I hit the refresh like five times, it'll happen. If I navigate away from the page and then try to type in msn.com again (in the same window) I hit refresh 5 times, to get the next page.
But if I type in www.msn.com it just generally well upward.
Even when he says that the page cannot be displayed, I have her pinger running in background ~ so I know that I can get for it. Weird huh?
I also have a question about licenses. When I get the pix firewall information, it says inside hosts: 10 but he let's have me 32 s ip for inside hosts. Does this mean that I'm having problems when I have more than 10 users browsing through the firewall? Or is that what I have as many hosts ip s?
Thanks in advance for any assistance.
1.) to refine the 10 limitation of host within the network you couold install another device inside network that PAT - translation of Port addresses that hide all the IP addresses behind his foreign address.
All PC-> [device router/PAT] - [PIX Firewall] - [router]-> Internet
(2.) to buy/pbtain a license longer write a mail to:
mailto:[email protected] / * /
The product update:
PIX-501-SW-10-50 = software upgrade license for 501 10 to 50 users PIX = approximately 340$ US
PIX-501-SW-10-UL = software upgrade license for the 501 user 10-for-unlimited PIX = about 400$ US
3.) World normal political deadlock depends on your company security policy, someone should set one, many companys trust their employees and allow all outgoing traffic. Might be good to block traffic P2P, Multimedia Streaming stuff, but this is not possible with OS 6.3.4 Release. You must wait for PIX OS 7.0, which is not available for PIX 501.
sincerely
Patrick
Tags: Cisco Security
Similar Questions
-
The import of the PIX 501 config to ASA 5505
Is there something special that must occur to import a PIX 501 (IOS Version 6.3) config to an ASA 5505 appliance or is it as simple as download the config?
Greg
No, this isn't unfortunately because your pix is running 6.4 and the ASA 5505 will run a minimum of code 7.x and there were quite a few changes. Note that many existing commands would work, but some will not. Attached is a link to a doc for improving pix ASA who speaks both a manual method and an assisted version of tool -.
http://www.Cisco.com/en/us/docs/security/ASA/migration/guide/pix2asa.html
Jon
-
PIX 501 in the firewall of the Web server
Hello
At the suggestion of a colleague, we bought a firewall PIX 501 to protect our new Win2003 web server and a UNIX/Oracle DB server.
I've never worked with before firewalls.
Our servers are located in a cage at the ISP and belong to us. There are only two servers providing web site. I have read the documentation in the Getting Started book and it does not answer my question.
We have 2 web sites with different IP numbers on our web server. Let's say 140.5.5.4 and 140.5.5.5. I understand that I have will redefine the numbers with the firewall (192,...) but I do not understand how the routers at the ISP will be able to route requests for two websites to the firewall when it has one IP number, say 140.5.5.1?
Any help is appreciated.
Thank you, Jerry
Jerry,
what you are referring is called port forwarding. Whether you a PIX with a public IP address 12.1.1.1 and your web servers are respectively and 12.1.1.2 12.1.1.3. Port forwarding is really a 2 step process:
* a static translation of the public IP address of the PIX (12.1.1.1) at the address of the web server (12.1.1.2)...
static (inside, outside) tcp 12.1.1.1 12.1.1.2 www www netmask 255.255.255.255 0 0
* an intermediate statement basically "all web requests should be allowed in the pix outside of the interface"...
driving permit tcp host 12.1.1.1 eq www everything
Here is a link that will help you to clarify this point:
www.Cisco.com/warp/Customer/707/28.html
This should help you get started. Regarding the basic configuration, it takes config examples on the Cisco site, if you have access CCO.
Let me know if it helps.
Rob H.
-
Cisco PIX 501, offered a license based on the connection: 10 or 100 users. What that means (e.g. for a 10 user license):
-a maximum of 10 xlates in the nat table?
-a maximum of 10 connections in the table conn?
If finally we're true, a user can establish 10 outbound connections (from an ip address). Currently, other users cannot establish a connection outboung?
Thank you
Edgar
"User" is defined as follows:
-a sent or received traffic via the PIX in the last xlate timeout seconds (five minutes with 501 default config).
-has a TCP or UDP connection
-a a NAT session
-a a session to authenticate user
It is certainly not the number of connections, but basically, the number of unique IP addresses internal that have any number of connections through the PIX. The 501 will support up to approximately 26000 connections, but only 10 internal IP addresses could use those.
You can make a "host local sho ' on the PIX to see all the current"users. "
-
I can not configure a pix 501 as a firewall, I need to know if it comes with a default configuration. I connect the PIX of the LAN and it start´s to DHCP each machine on the network with no problem, but none of the user´s can access the internet.
I need to know what to do to get access to internet protection and network security.
Where can I go to configure the Pix, if I really need to configure it!
Hi... basically, you need the following basic steps to access your internal users to the internet
If you use 6.3 (5) PIX
interface ethernet0 100full
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
inside_access_in ip access list allow a whole
inside_access_in access to the interface inside group
NAT (inside) 1 access-list inside_access_in
Global 1 interface (outside)
NOTE: with the config ablove room your internal users will have FULL access to the internet. If you want to restrict access to only http, https, ftp, dns, etc then you need to change the access list for something like that...
inside_access_in list access permit tcp any any eq www
inside_access_in list access permit tcp any any eq 443
inside_access_in list access permit tcp any any eq ftp
inside_access_in list access permit tcp any any eq 53
inside_access_in udd allowed access list any any eq 53
I hope that helps... Rate if he does!
-
IPSec VPN pix 501 no LAN access
I'm trying to set up an IPSec VPN in a basic small business scenario. I am able to connect to my pix 501 via IPSec VPN and browse the internet, but I am unable to ping or you connect to all devices in the Remote LAN. Here is my config:
: Saved
:
6.3 (3) version PIX
interface ethernet0 car
interface ethernet1 100full
nameif ethernet0 WAN security0
nameif ethernet1 LAN security99
enable encrypted password xxxxxxxxxxxxx
xxxxxxxxxxxxxxxxx encrypted passwd
host name snowball
domain xxxxxxxxxxxx.local
clock timezone PST - 8
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
No fixup not protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
acl_in list of access permit udp any any eq field
acl_in list of access permit udp any eq field all
acl_in list access permit tcp any any eq field
acl_in tcp allowed access list any domain eq everything
acl_in list access permit icmp any any echo response
access-list acl_in allow icmp all once exceed
acl_in list all permitted access all unreachable icmp
acl_in list access permit tcp any any eq ssh
acl_in list access permit tcp any any eq www
acl_in tcp allowed access list everything all https eq
acl_in list access permit tcp any host 192.168.5.30 eq 81
acl_in list access permit tcp any host 192.168.5.30 eq 8081
acl_in list access permit tcp any host 192.168.5.22 eq 8081
acl_in list access permit icmp any any echo
access-list acl_in permit tcp host 76.248.x.x a
access-list acl_in permit tcp host 76.248.x.x a
allow udp host 76.248.x.x one Access-list acl_in
access-list acl_out permit icmp any one
ip access list acl_out permit a whole
acl_out list access permit icmp any any echo response
acl_out list access permit icmp any any source-quench
allowed any access list acl_out all unreachable icmp
access-list acl_out permit icmp any once exceed
acl_out list access permit icmp any any echo
Allow Access-list no. - nat icmp a whole
access-list no. - nat ip 192.168.5.0 allow 255.255.255.0 172.16.0.0 255.255.0.0
access-list no. - nat ip 172.16.0.0 allow 255.255.0.0 any
access-list no. - nat permit icmp any any echo response
access-list no. - nat permit icmp any any source-quench
access-list no. - nat icmp permitted all all inaccessible
access-list no. - nat allow icmp all once exceed
access-list no. - nat permit icmp any any echo
pager lines 24
MTU 1500 WAN
MTU 1500 LAN
IP address WAN 65.74.x.x 255.255.255.240
address 192.168.5.1 LAN IP 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP local pool pptppool 172.16.0.2 - 172.16.0.13
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global (WAN) 1 interface
NAT (LAN) - access list 0 no - nat
NAT (LAN) 1 0.0.0.0 0.0.0.0 0 0
static (LAN, WAN) 65.x.x.37 192.168.5.10 netmask 255.255.255.255 0 0
static (LAN, WAN) 65.x.x.36 192.168.5.20 netmask 255.255.255.255 0 0
static (LAN, WAN) 65.x.x.38 192.168.5.30 netmask 255.255.255.255 0 0
static (LAN, WAN) 65.x.x.39 192.168.5.40 netmask 255.255.255.255 0 0
static (LAN, WAN) 65.x.x.42 192.168.5.22 netmask 255.255.255.255 0 0
static (LAN, WAN) 65.x.x.43 192.168.5.45 netmask 255.255.255.255 0 0
static (LAN, WAN) 65.x.x.44 192.168.5.41 netmask 255.255.255.255 0 0
static (LAN, WAN) 65.x.x.45 192.168.5.42 netmask 255.255.255.255 0 0
static (LAN, WAN) 65.x.x.46 192.168.5.44 netmask 255.255.255.255 0 0
static (LAN, WAN) 65.x.x.41 192.168.5.21 netmask 255.255.255.255 0 0
acl_in access to the WAN interface group
access to the LAN interface group acl_out
Route WAN 0.0.0.0 0.0.0.0 65.x.x.34 1
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
NTP server 72.14.188.195 source WAN
survey of 76.248.x.x WAN host SNMP Server
location of Server SNMP Sacramento
SNMP Server contact [email protected] / * /
SNMP-Server Community xxxxxxxxxxxxx
SNMP-Server enable traps
enable floodguard
the string 1 WAN fragment
Permitted connection ipsec sysopt
Sysopt connection permit-pptp
Crypto ipsec transform-set esp - esp-md5-hmac RIGHT
Crypto-map dynamic dynmap 10 transform-set RIGHT
map mymap 10-isakmp ipsec crypto dynamic dynmap
client configuration address map mymap crypto initiate
client configuration address map mymap crypto answer
card crypto mymap WAN interface
ISAKMP enable WAN
ISAKMP nat-traversal 20
part of pre authentication ISAKMP policy 10
encryption of ISAKMP policy 10
ISAKMP policy 10 md5 hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
vpngroup myvpn address pptppool pool
vpngroup myvpn Server dns 192.168.5.44
vpngroup myvpn by default-field xxxxxxxxx.local
vpngroup split myvpn No. - nat tunnel
vpngroup idle 1800 myvpn-time
vpngroup myvpn password *.
Telnet 192.168.5.0 255.255.255.0 LAN
Telnet timeout 5
SSH 192.168.5.0 255.255.255.0 LAN
SSH timeout 30
Console timeout 0
VPDN group pptpusers accept dialin pptp
VPDN group ppp authentication pap pptpusers
VPDN group ppp authentication chap pptpusers
VPDN group ppp mschap authentication pptpusers
VPDN group ppp encryption mppe 128 pptpusers
VPDN group pptpusers client configuration address local pptppool
VPDN group pptpusers customer 192.168.5.44 dns configuration
VPDN group pptpusers pptp echo 60
VPDN group customer pptpusers of local authentication
VPDN username password xxx *.
VPDN username password xxx *.
VPDN enable WAN
dhcpd address 192.168.5.200 - 192.168.5.220 LAN
dhcpd 192.168.5.44 dns 8.8.8.8
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd enable LAN
username privilege 0 encrypted password xxxxxxxxxx xxxxxxxxxxx
username privilege 0 encrypted password xxxxxxxxxx xxxxxxxxxxx
Terminal width 80
Cryptochecksum:xxxxxxxxxxxxxxxxxx
: end
I'm sure it has something to do with NAT or an access list, but I can't understand it at all. I know it's a basic question, but I would really appreaciate help!Thank you very muchTrevor"No. - nat' ACL doesn't seem correct, please make sure you want to remove the following text:
do not allow any No. - nat icmp access list a whole
No No. - nat ip 172.16.0.0 access list allow 255.255.0.0 any
No No. - nat access list permit icmp any any echo response
No No. - nat access list permit icmp any any source-quench
No No. - nat access list permit all all unreachable icmp
No No. - nat access list do not allow icmp all once exceed
No No. - nat access list only allowed icmp no echo
You must have 1 line as follows:
access-list no. - nat ip 192.168.5.0 allow 255.255.255.0 172.16.0.0 255.255.0.0
Please 'clear xlate' after the changes described above.
In addition, if you have a personal firewall enabled on the host you are trying to connect from the Client VPN, please turn it off and try again. Personal firewall of Windows normally blocks the traffic of different subnets.
Hope that helps.
-
Connectivity random Cisco Pix 501
Hello. I'm having some trouble with my CISCO PIX 501 Setup.
A few months I started having random disconnects on my network (from inside to outside). The machines can ping the DC or the Pix, but impossible to surf the internet. The only way to make them go outside is a reboot of Pix.
My configuration is:
-----------
See the ACE - pix config (config) #.
: Saved
: Written by enable_15 at 09:23:07.033 UTC Tuesday, June 3, 2014
6.3 (3) version PIX
interface ethernet0 car
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate 8Ry34retyt7RR564 encrypted password
2fvbbfgdI.2KUOU encrypted passwd
hostname as pix
domain as.local
fixup protocol dns-length maximum 512
fixup protocol esp-ike
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
access-list acl_out permit icmp any one
ip access list acl_out permit a whole
access-list acl_out permit tcp any one
Allow Access-list outside_access_in esp a whole
outside_access_in list access permit udp any eq isakmp everything
outside_access_in list of access permit udp any eq 1701 all
outside_access_in list of access permit udp any eq 4500 all
outside_access_in ip access list allow a whole
pager lines 24
Outside 1500 MTU
Within 1500 MTU
outside 10.10.10.2 IP address 255.255.255.0
IP address inside 192.168.100.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
history of PDM activate
ARP timeout 14400
Global 1 10.10.10.8 - 10.10.10.254 (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Access-group outside_access_in in interface outside
access to the interface inside group acl_out
Route outside 0.0.0.0 0.0.0.0 10.10.10.1 0
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.10.2 255.255.255.255 inside
http 192.168.10.101 255.255.255.255 inside
http 192.168.100.2 255.255.255.255 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
ISAKMP nat-traversal 20
Telnet timeout 5
SSH 192.168.10.101 255.255.255.255 inside
SSH timeout 60
Console timeout 0
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd outside auto_config
Terminal width 80
Cryptochecksum:7f9bda5e534eaeb1328ab08a3c4d28a
------------Do you have any advice? I don't get what's wrong with my setup.
My DC is 192.168.100.2 and the network mask is 255.255.255.0
The network configuration is configured to set the IP of the gateway to 192.168.100.1 (i.e. the PIX 501).
I have about 50 + peers on the internal network.
Any help is apprecciate.
Hello
You have a license for 50 users +?
After the release of - Show version
RES
Paul
-
Hello.. I am beginner in this kind of things cisco...
I'm trying to set up multiple VPN on a Cisco PIX 501 firewall with routers Linksys BEFVP41...
Since not very familiar with the CLI, I use the PDM utility and it was very easy for the first... Unfortunately, I get this error when I try to add the second VPN using the VPN Wizard:
Outside_map map (ERR) crypto set peer 200.20.10.3
WARNING: This encryption card is incomplete
To remedy the situation even and a list of valid to add this encryption card
Hi garcia
for each vpn/peer, you need to a separate instance of crypto card, the card will have the same name, but different sequence... numbers one map encryption can be attributed to an interface, but you can have several instance of cards inside a main...
for configuration, you can go through the URL below... It has all the details on IPSEC config:
http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_63/config/ipsecint.htm
I hope this helps... all the best... the rate of responses if deemed useful...
REDA
-
I have a PIX 501 with wired high-speed LAN headquarters inside and outside. Which would be a solid policy IDS to enable and what interfaces it must be applied to? There will be other measures necessary to enable IDS?
IDS on the PIX itself is very limited, it checks only 59 signatures listed here (http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_62/cmdref/gl.htm#xtocid9 under the section of signatures supported IDS). The signatures themselves are pretty basic.
If you do not want to activate this, then for the signatures of attacks I would fix for drop/alarm/reset action, which is the default anyway.
You will also need to set the logging to a syslog server and monitoring for any 4000nn messages in syslog, cause it event IDS.
-
I would like to access my PC location xyz. How can I open port 22 access to my pc. I use pix 501.
Can anyone provide commands to open the port so that I can access my pc.
Thank you
totally agree because only 3 commands are needed.
list of allowed inbound tcp access any eq 22
public static tcp (indoor, outdoor) interface 22 22 netmask 255.255.255.255 0 0
clear xlate
However, all of these commands are missing in the config you have posted.
-
PAT on IPSEC VPN (Pix 501)
Hello
I work to connect a PIX 501 VPN for a 3rd party hub 3015. The hub requires all traffic to come from a single source IP address. This IP address is assigned to me as z.z.z.z. I have successfully built the VPN and tested by mapping staticly internal IP with the IP address assigned, but cannot get the orders right to do with PAT in order to have more than one computer on the subnet 10.x.x.0. This Pix is also a backup for internet routing and NAT work currently as well for this.
I can redirect traffic to my subnet to the remote subnet via the VPN, but I can't seem to get the right stuff PAT to the VPN using the assigned IP address. If anyone can give me some advice that would be great.
lines of current config interesting configuration with static mapping:
--------------------------------------------------------------------------
access-list 101 permit ip 10.0.0.0 255.255.255.0 y.y.y.0 255.255.255.0
access-list 102 permit ip y.y.y.0 255.255.255.0 z.z.z.z host
access-list 103 allow host ip y.y.y.0 255.255.255.0 z.z.z.z
IP address outside w.w.w.1 255.255.255.248
IP address inside 10.0.0.1 255.255.255.0
Global 1 interface (outside)
NAT (inside) - 0 102 access list
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
public static z.z.z.z (Interior, exterior) 10.x.x.50 netmask 255.255.255.255 0 0
Route outside 0.0.0.0 0.0.0.0 w.w.w.2 1
correspondence address card crypto mymap 10 103
mymap outside crypto map interface
ISAKMP allows outside
Thank you!
Dave
Dave,
(1) get rid of static electricity. Use more Global/NAT. The static method will create a permanent
translation for your guests inside and they will always be this way natted. Use
NAT of politics, on the contrary, as shown here:
not static (inside, outside) z.z.z.z 10.x.x.50 netmask 255.255.255.255 0 0
Global (outside) 2 z.z.z.z netmask 255.255.255.255
(Inside) NAT 2-list of access 101
(2) the statement, "nat (inside) access 0 2' list will prevent nat of your valuable traffic."
Delete this because you need to nat 2 nat/global card. (as a general rule, simply you
If you terminate VPN clients on your device and do not want inside the traffic which
is intended for the vpn clients to be natted on the external interface).
(3) with the instructions of Global/nat 2, all traffic destined for the remote network will be first
translated into z.z.z.z. Then your card crypto using the ACL 103 will encrypt all traffic which
sources of z.z.z.z for y.y.y.0 24. This translation wil happen only when traffic is destined for the vpn.
I hope this helps. I have this work on many tunnels as you describe.
Jamison
-
Unable to connect to PDM on PIX 501
just cannot understand this. I have a PIX 501 I used to connect very well. Now I can't get the PDM to come up inside, outside, nothing. I use the same (old) of JAVA 1.4 version I always used. I can Telnet etc... Very well. The HTTP server is enabled and have granted access from my IP address. Any help would be greatly appreciated. See my config below.
See the pixfirewall # running
: Saved
:
6.3 (5) PIX version
interface ethernet0 car
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate 8Ry2YjIyt7RRXU24 encrypted password
passwd encrypted XXXXXXXX
pixfirewall hostname
domain ciscopix.com
clock timezone IS - 5
clock to summer time EDT recurring
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 X 0
fixup protocol h323 ras X 18 - X 19
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
name admin_subnet X.X.X.X
inside_outbound_nat0_acl X.X.X.X 255.255.255.0 ip access list allow admin_
subnet 255.255.0.0
inside_outbound_nat0_acl X.X.X.X 255.255.255.0 ip access list allow X.X
. X.X 255.255.255.0
outside_cryptomap_20 X.X.X.X 255.255.255.0 ip access list permit admin_subn
and 255.255.0.0
outside_cryptomap_20 X.X.X.X 255.255.255.0 ip access list allow X.X.X
. X 255.255.255.0
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP outside X.X.X.X 255.255.255.128
inside X.X.X.X 255.255.255.0 IP address
alarm action IP verification of information
alarm action attack IP audit
PDM location admin_subnet 255.255.0.0 outside
location of PDM X.X.X.X 255.255.255.0 inside
PDM location x.x.x.x 255.255.255.255 outside
location of PDM X.X.X.X 255.255.255.0 outside
location of PDM X.X.X.X 255.255.255.255 outside
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route outside 0.0.0.0 0.0.0.0 X.X.X.X 1
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
LOCAL AAA authentication serial console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
Enable http server
http X.X.X.X 255.255.255.0 inside
http admin_subnet 255.255.0.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
outside_map 20 ipsec-isakmp crypto map
card crypto outside_map 20 match address outside_cryptomap_20
card crypto outside_map pfs set 20 group2
card crypto outside_map 20 game peers X.X.X.X
outside_map crypto 20 card value transform-set ESP-AES-256-SHA
outside_map interface card crypto outside
ISAKMP allows outside
ISAKMP key * address X.X.X.X 255.255.255.255 netmask No.-xauth non - co
Nfig-mode
part of pre authentication ISAKMP policy 20
ISAKMP policy 20 aes-256 encryption
ISAKMP policy 20 chopping sha
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 8 X 00
Telnet X.X.X.X 255.255.255.0 outside
Telnet X.X.X.X 255.255.255.0 inside
Telnet admin_subnet 255.255.0.0 inside
Telnet timeout 30
ssh X.X.X.X 255.255.255.255 outside
X.X.X.X 255.255.255.0 inside SSH
SSH timeout 30
management-access inside
Console timeout 30
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd lease 3600
dhcpd ping_timeout 750
username password XXXXXX XXXXXXXXXXX encrypted privilege 15
Terminal width 80
Cryptochecksum:
: endHello Mark,
lol Nice to know that everything works fine now
Don't forget to mark it as answered and to classify the useful messages (if you don't know how to evaluate a message just to get to the bottom of each answer and mark 1 being a wrong answer, being a great answer 5 stars)
Kind regards
Julio
PD: Some kudos for you (because of the answer)
-
L2l IPSec VPN 3000 and PIX 501
Hello
I have a remote site that has a broadband internet connection and uses a PIX 501. We wanted to connect them with our main office using our VPN 3000 via VPN site-to-site.
I followed the following documentation:
However the L2L session does not appear on the hub when I check the active sessions.
The network diagram, as well as the PIX config and the screenshots of the VPN configuration for the IPSec-L2L tunnel is attached.
Any help or advice are appreciated.
I just noticed that the PIX firewall, the phase 1 paramateres are not configured. You must configure the same PASE 1 and phase 2 settings on both ends of the tunnel.
For example, on CVPN 3000, you have configured settings Phase 1 as 3DES, pre-shared key etc... We have the same configuration on the PIX firewall too.
Here is an example of sample config
I hope this helps!
-
Newbie Pix 501 HTTP authentication timeout
two issues here:
1. users that connect to the Internet through the Pix 501 ask about every three minutes to enter their user name and password. There must be a setting to change this, my dealer said there is no.
2. users that connect to the Internet, the first time have their IE session. By clicking Stop and then refresh or House brings to the top of the page. Any ideas.
Thanks in advance for any ideas you may have
Jeff Charland
Jeff,
First rule is to never trust your seller on technical issues;). Your dealer is wrong. You can indeed change the moment where a user is re - you are prompted to enter their credentials. There are basically 2 parameters, you need to know about the pix regarding delays of authentication:
(1) the inactivity timer. It's just like that. It expires an authenticated session via the PIX to hit X amount of time without all the traffic. The default timer on the PIX for this setting is 0, which means that we are no period of inactivity by the user (by default) monitor.
(2) the absoltue timer. Again, is to noise. This timer starts as soon as the user is authenticated and works continuously. When the time is reached, the user is obliged to to re-authenticate when they try to start a new connection (for example, by clicking a link in a web page). The default setting for the absolute timer is 5 minutes.
We recommend that you do not keep an absolute clock set for security purposes, but for ease of access, you can change these settings. Something like that would not be a 'off the wall' setting:
timeout uauth 01:00 absolute uauth 0: idle from 10:00
These settings will force the user to to re-authenticate every hour (absolute) or every 10 minutes after the connection becomes inactive.
And finally, no idea about #2 above. It happens with all users. Anyone who has tried to Netscape to see if it is a question only IE?
Scott
-
Hi all. Just a quick question. I can't seem to find how to reset ipsec on PIX 501 and force her to negotiate again and I also want to reset statistics for ipsec his. I know that I saw somewhere, orders, but now can't seem to find the commands from anywhere.
Thanks in advance for any help.
Hello...
Config mode...
ISAKMP crypto claire his
- and -
clear crypto ipsec his
PS. You can find the commands on the PIX by entering the configuration mode by typing...
PIX01 (config) # clear cry?
Hope the above helps and please note messages!
Maybe you are looking for
-
When I send a sketch to Apple Watch my wife the same sketch I just sent to his shows on my Apple Watch as well. I don't know that it's because somewhere she has my Apple ID stored on his watch, but I can't find where it is stored.
-
Hi all Im trying to program a compact module NI 9403 using labview and crio9024, but first I should remove simulated hardwares. but it's impossible caz somehow I do not see these devices in the configuration tab (see the attached photo please), can s
-
I have to sign each time that I will go to my hotmail it's because of my firewall
I sign every time that I go to my hotmail.com .even if I check Disable the box connect
-
HP g72: admin password! error # 87163410
I need this code bypass ro stat! Time sensarive! Thank you
-
What is the best way to transfer all my installed programs and data to another computer with ease?I am currently using Windows Vista Ultimate Edition with service pack 2. Can anyone help? Thank you.