Reseting ipsec on PIX 501

Hi all. Just a quick question. I can't seem to find how to reset ipsec on PIX 501 and force her to negotiate again and I also want to reset statistics for ipsec his. I know that I saw somewhere, orders, but now can't seem to find the commands from anywhere.

Thanks in advance for any help.

Hello...

Config mode...

ISAKMP crypto claire his

- and -

clear crypto ipsec his

PS. You can find the commands on the PIX by entering the configuration mode by typing...

PIX01 (config) # clear cry?

Hope the above helps and please note messages!

Tags: Cisco Security

Similar Questions

IPSec VPN pix 501 no LAN access

I'm trying to set up an IPSec VPN in a basic small business scenario. I am able to connect to my pix 501 via IPSec VPN and browse the internet, but I am unable to ping or you connect to all devices in the Remote LAN. Here is my config:

: Saved

:

6.3 (3) version PIX

interface ethernet0 car

interface ethernet1 100full

nameif ethernet0 WAN security0

nameif ethernet1 LAN security99

enable encrypted password xxxxxxxxxxxxx

xxxxxxxxxxxxxxxxx encrypted passwd

host name snowball

domain xxxxxxxxxxxx.local

clock timezone PST - 8

fixup protocol dns-length maximum 512

fixup protocol ftp 21

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol http 80

fixup protocol pptp 1723

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol sip 5060

fixup protocol sip udp 5060

fixup protocol 2000 skinny

No fixup not protocol smtp 25

fixup protocol sqlnet 1521

fixup protocol tftp 69

names of

acl_in list of access permit udp any any eq field

acl_in list of access permit udp any eq field all

acl_in list access permit tcp any any eq field

acl_in tcp allowed access list any domain eq everything

acl_in list access permit icmp any any echo response

access-list acl_in allow icmp all once exceed

acl_in list all permitted access all unreachable icmp

acl_in list access permit tcp any any eq ssh

acl_in list access permit tcp any any eq www

acl_in tcp allowed access list everything all https eq

acl_in list access permit tcp any host 192.168.5.30 eq 81

acl_in list access permit tcp any host 192.168.5.30 eq 8081

acl_in list access permit tcp any host 192.168.5.22 eq 8081

acl_in list access permit icmp any any echo

access-list acl_in permit tcp host 76.248.x.x a

access-list acl_in permit tcp host 76.248.x.x a

allow udp host 76.248.x.x one Access-list acl_in

access-list acl_out permit icmp any one

ip access list acl_out permit a whole

acl_out list access permit icmp any any echo response

acl_out list access permit icmp any any source-quench

allowed any access list acl_out all unreachable icmp

access-list acl_out permit icmp any once exceed

acl_out list access permit icmp any any echo

Allow Access-list no. - nat icmp a whole

access-list no. - nat ip 192.168.5.0 allow 255.255.255.0 172.16.0.0 255.255.0.0

access-list no. - nat ip 172.16.0.0 allow 255.255.0.0 any

access-list no. - nat permit icmp any any echo response

access-list no. - nat permit icmp any any source-quench

access-list no. - nat icmp permitted all all inaccessible

access-list no. - nat allow icmp all once exceed

access-list no. - nat permit icmp any any echo

pager lines 24

MTU 1500 WAN

MTU 1500 LAN

IP address WAN 65.74.x.x 255.255.255.240

address 192.168.5.1 LAN IP 255.255.255.0

alarm action IP verification of information

alarm action attack IP audit

IP local pool pptppool 172.16.0.2 - 172.16.0.13

PDM logging 100 information

history of PDM activate

ARP timeout 14400

Global (WAN) 1 interface

NAT (LAN) - access list 0 no - nat

NAT (LAN) 1 0.0.0.0 0.0.0.0 0 0

static (LAN, WAN) 65.x.x.37 192.168.5.10 netmask 255.255.255.255 0 0

static (LAN, WAN) 65.x.x.36 192.168.5.20 netmask 255.255.255.255 0 0

static (LAN, WAN) 65.x.x.38 192.168.5.30 netmask 255.255.255.255 0 0

static (LAN, WAN) 65.x.x.39 192.168.5.40 netmask 255.255.255.255 0 0

static (LAN, WAN) 65.x.x.42 192.168.5.22 netmask 255.255.255.255 0 0

static (LAN, WAN) 65.x.x.43 192.168.5.45 netmask 255.255.255.255 0 0

static (LAN, WAN) 65.x.x.44 192.168.5.41 netmask 255.255.255.255 0 0

static (LAN, WAN) 65.x.x.45 192.168.5.42 netmask 255.255.255.255 0 0

static (LAN, WAN) 65.x.x.46 192.168.5.44 netmask 255.255.255.255 0 0

static (LAN, WAN) 65.x.x.41 192.168.5.21 netmask 255.255.255.255 0 0

acl_in access to the WAN interface group

access to the LAN interface group acl_out

Route WAN 0.0.0.0 0.0.0.0 65.x.x.34 1

Timeout xlate 0:05:00

Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

Timeout, uauth 0:05:00 absolute

GANYMEDE + Protocol Ganymede + AAA-server

RADIUS Protocol RADIUS AAA server

AAA-server local LOCAL Protocol

NTP server 72.14.188.195 source WAN

survey of 76.248.x.x WAN host SNMP Server

location of Server SNMP Sacramento

SNMP Server contact [email protected] / * /

SNMP-Server Community xxxxxxxxxxxxx

SNMP-Server enable traps

enable floodguard

the string 1 WAN fragment

Permitted connection ipsec sysopt

Sysopt connection permit-pptp

Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

Crypto-map dynamic dynmap 10 transform-set RIGHT

map mymap 10-isakmp ipsec crypto dynamic dynmap

client configuration address map mymap crypto initiate

client configuration address map mymap crypto answer

card crypto mymap WAN interface

ISAKMP enable WAN

ISAKMP nat-traversal 20

part of pre authentication ISAKMP policy 10

encryption of ISAKMP policy 10

ISAKMP policy 10 md5 hash

10 2 ISAKMP policy group

ISAKMP life duration strategy 10 86400

vpngroup myvpn address pptppool pool

vpngroup myvpn Server dns 192.168.5.44

vpngroup myvpn by default-field xxxxxxxxx.local

vpngroup split myvpn No. - nat tunnel

vpngroup idle 1800 myvpn-time

vpngroup myvpn password *.

Telnet 192.168.5.0 255.255.255.0 LAN

Telnet timeout 5

SSH 192.168.5.0 255.255.255.0 LAN

SSH timeout 30

Console timeout 0

VPDN group pptpusers accept dialin pptp

VPDN group ppp authentication pap pptpusers

VPDN group ppp authentication chap pptpusers

VPDN group ppp mschap authentication pptpusers

VPDN group ppp encryption mppe 128 pptpusers

VPDN group pptpusers client configuration address local pptppool

VPDN group pptpusers customer 192.168.5.44 dns configuration

VPDN group pptpusers pptp echo 60

VPDN group customer pptpusers of local authentication

VPDN username password xxx *.

VPDN username password xxx *.

VPDN enable WAN

dhcpd address 192.168.5.200 - 192.168.5.220 LAN

dhcpd 192.168.5.44 dns 8.8.8.8

dhcpd lease 3600

dhcpd ping_timeout 750

dhcpd enable LAN

username privilege 0 encrypted password xxxxxxxxxx xxxxxxxxxxx

username privilege 0 encrypted password xxxxxxxxxx xxxxxxxxxxx

Terminal width 80

Cryptochecksum:xxxxxxxxxxxxxxxxxx

: end

I'm sure it has something to do with NAT or an access list, but I can't understand it at all. I know it's a basic question, but I would really appreaciate help!

Thank you very much

Trevor

"No. - nat' ACL doesn't seem correct, please make sure you want to remove the following text:

do not allow any No. - nat icmp access list a whole

No No. - nat ip 172.16.0.0 access list allow 255.255.0.0 any

No No. - nat access list permit icmp any any echo response

No No. - nat access list permit icmp any any source-quench

No No. - nat access list permit all all unreachable icmp

No No. - nat access list do not allow icmp all once exceed

No No. - nat access list only allowed icmp no echo

You must have 1 line as follows:

access-list no. - nat ip 192.168.5.0 allow 255.255.255.0 172.16.0.0 255.255.0.0

Please 'clear xlate' after the changes described above.

In addition, if you have a personal firewall enabled on the host you are trying to connect from the Client VPN, please turn it off and try again. Personal firewall of Windows normally blocks the traffic of different subnets.

Hope that helps.

PAT on IPSEC VPN (Pix 501)

Hello

I work to connect a PIX 501 VPN for a 3rd party hub 3015. The hub requires all traffic to come from a single source IP address. This IP address is assigned to me as z.z.z.z. I have successfully built the VPN and tested by mapping staticly internal IP with the IP address assigned, but cannot get the orders right to do with PAT in order to have more than one computer on the subnet 10.x.x.0. This Pix is also a backup for internet routing and NAT work currently as well for this.

I can redirect traffic to my subnet to the remote subnet via the VPN, but I can't seem to get the right stuff PAT to the VPN using the assigned IP address. If anyone can give me some advice that would be great.

lines of current config interesting configuration with static mapping:

--------------------------------------------------------------------------

access-list 101 permit ip 10.0.0.0 255.255.255.0 y.y.y.0 255.255.255.0

access-list 102 permit ip y.y.y.0 255.255.255.0 z.z.z.z host

access-list 103 allow host ip y.y.y.0 255.255.255.0 z.z.z.z

IP address outside w.w.w.1 255.255.255.248

IP address inside 10.0.0.1 255.255.255.0

Global 1 interface (outside)

NAT (inside) - 0 102 access list

NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

public static z.z.z.z (Interior, exterior) 10.x.x.50 netmask 255.255.255.255 0 0

Route outside 0.0.0.0 0.0.0.0 w.w.w.2 1

correspondence address card crypto mymap 10 103

mymap outside crypto map interface

ISAKMP allows outside

Thank you!

Dave

Dave,

(1) get rid of static electricity. Use more Global/NAT. The static method will create a permanent

translation for your guests inside and they will always be this way natted. Use

NAT of politics, on the contrary, as shown here:

not static (inside, outside) z.z.z.z 10.x.x.50 netmask 255.255.255.255 0 0

Global (outside) 2 z.z.z.z netmask 255.255.255.255

(Inside) NAT 2-list of access 101

(2) the statement, "nat (inside) access 0 2' list will prevent nat of your valuable traffic."

Delete this because you need to nat 2 nat/global card. (as a general rule, simply you

If you terminate VPN clients on your device and do not want inside the traffic which

is intended for the vpn clients to be natted on the external interface).

(3) with the instructions of Global/nat 2, all traffic destined for the remote network will be first

translated into z.z.z.z. Then your card crypto using the ACL 103 will encrypt all traffic which

sources of z.z.z.z for y.y.y.0 24. This translation wil happen only when traffic is destined for the vpn.

I hope this helps. I have this work on many tunnels as you describe.

Jamison

L2l IPSec VPN 3000 and PIX 501

Hello

I have a remote site that has a broadband internet connection and uses a PIX 501. We wanted to connect them with our main office using our VPN 3000 via VPN site-to-site.

I followed the following documentation:

http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml#tshoot

However the L2L session does not appear on the hub when I check the active sessions.

The network diagram, as well as the PIX config and the screenshots of the VPN configuration for the IPSec-L2L tunnel is attached.

Any help or advice are appreciated.

I just noticed that the PIX firewall, the phase 1 paramateres are not configured. You must configure the same PASE 1 and phase 2 settings on both ends of the tunnel.

For example, on CVPN 3000, you have configured settings Phase 1 as 3DES, pre-shared key etc... We have the same configuration on the PIX firewall too.

Here is an example of sample config

http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml

I hope this helps!

Connectivity random Cisco Pix 501

Hello. I'm having some trouble with my CISCO PIX 501 Setup.

A few months I started having random disconnects on my network (from inside to outside). The machines can ping the DC or the Pix, but impossible to surf the internet. The only way to make them go outside is a reboot of Pix.

My configuration is:

-----------

See the ACE - pix config (config) #.
: Saved
: Written by enable_15 at 09:23:07.033 UTC Tuesday, June 3, 2014
6.3 (3) version PIX
interface ethernet0 car
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate 8Ry34retyt7RR564 encrypted password
2fvbbfgdI.2KUOU encrypted passwd
hostname as pix
domain as.local
fixup protocol dns-length maximum 512
fixup protocol esp-ike
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
access-list acl_out permit icmp any one
ip access list acl_out permit a whole
access-list acl_out permit tcp any one
Allow Access-list outside_access_in esp a whole
outside_access_in list access permit udp any eq isakmp everything
outside_access_in list of access permit udp any eq 1701 all
outside_access_in list of access permit udp any eq 4500 all
outside_access_in ip access list allow a whole
pager lines 24
Outside 1500 MTU
Within 1500 MTU
outside 10.10.10.2 IP address 255.255.255.0
IP address inside 192.168.100.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
history of PDM activate
ARP timeout 14400
Global 1 10.10.10.8 - 10.10.10.254 (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Access-group outside_access_in in interface outside
access to the interface inside group acl_out
Route outside 0.0.0.0 0.0.0.0 10.10.10.1 0
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.10.2 255.255.255.255 inside
http 192.168.10.101 255.255.255.255 inside
http 192.168.100.2 255.255.255.255 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
ISAKMP nat-traversal 20
Telnet timeout 5
SSH 192.168.10.101 255.255.255.255 inside
SSH timeout 60
Console timeout 0
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd outside auto_config
Terminal width 80
Cryptochecksum:7f9bda5e534eaeb1328ab08a3c4d28a
------------

Do you have any advice? I don't get what's wrong with my setup.

My DC is 192.168.100.2 and the network mask is 255.255.255.0

The network configuration is configured to set the IP of the gateway to 192.168.100.1 (i.e. the PIX 501).

I have about 50 + peers on the internal network.

Any help is apprecciate.

Hello

You have a license for 50 users +?

After the release of - Show version

RES

Paul

Adding a pix 501 VPN 2

Hello.. I am beginner in this kind of things cisco...

I'm trying to set up multiple VPN on a Cisco PIX 501 firewall with routers Linksys BEFVP41...

Since not very familiar with the CLI, I use the PDM utility and it was very easy for the first... Unfortunately, I get this error when I try to add the second VPN using the VPN Wizard:

Outside_map map (ERR) crypto set peer 200.20.10.3

WARNING: This encryption card is incomplete

To remedy the situation even and a list of valid to add this encryption card

Hi garcia

for each vpn/peer, you need to a separate instance of crypto card, the card will have the same name, but different sequence... numbers one map encryption can be attributed to an interface, but you can have several instance of cards inside a main...

for configuration, you can go through the URL below... It has all the details on IPSEC config:

http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_63/config/ipsecint.htm

I hope this helps... all the best... the rate of responses if deemed useful...

REDA

Configure the PIX 501 for IDS

I have a PIX 501 with wired high-speed LAN headquarters inside and outside. Which would be a solid policy IDS to enable and what interfaces it must be applied to? There will be other measures necessary to enable IDS?

IDS on the PIX itself is very limited, it checks only 59 signatures listed here (http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_62/cmdref/gl.htm#xtocid9 under the section of signatures supported IDS). The signatures themselves are pretty basic.

If you do not want to activate this, then for the signatures of attacks I would fix for drop/alarm/reset action, which is the default anyway.

You will also need to set the logging to a syslog server and monitoring for any 4000nn messages in syslog, cause it event IDS.

Unable to connect to PDM on PIX 501

just cannot understand this. I have a PIX 501 I used to connect very well. Now I can't get the PDM to come up inside, outside, nothing. I use the same (old) of JAVA 1.4 version I always used. I can Telnet etc... Very well. The HTTP server is enabled and have granted access from my IP address. Any help would be greatly appreciated. See my config below.

See the pixfirewall # running
: Saved
:
6.3 (5) PIX version
interface ethernet0 car
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate 8Ry2YjIyt7RRXU24 encrypted password
passwd encrypted XXXXXXXX
pixfirewall hostname
domain ciscopix.com
clock timezone IS - 5
clock to summer time EDT recurring
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 X 0
fixup protocol h323 ras X 18 - X 19
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
name admin_subnet X.X.X.X
inside_outbound_nat0_acl X.X.X.X 255.255.255.0 ip access list allow admin_
subnet 255.255.0.0
inside_outbound_nat0_acl X.X.X.X 255.255.255.0 ip access list allow X.X
. X.X 255.255.255.0
outside_cryptomap_20 X.X.X.X 255.255.255.0 ip access list permit admin_subn
and 255.255.0.0
outside_cryptomap_20 X.X.X.X 255.255.255.0 ip access list allow X.X.X
. X 255.255.255.0
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP outside X.X.X.X 255.255.255.128
inside X.X.X.X 255.255.255.0 IP address
alarm action IP verification of information
alarm action attack IP audit
PDM location admin_subnet 255.255.0.0 outside
location of PDM X.X.X.X 255.255.255.0 inside
PDM location x.x.x.x 255.255.255.255 outside
location of PDM X.X.X.X 255.255.255.0 outside
location of PDM X.X.X.X 255.255.255.255 outside
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route outside 0.0.0.0 0.0.0.0 X.X.X.X 1
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
LOCAL AAA authentication serial console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
Enable http server
http X.X.X.X 255.255.255.0 inside
http admin_subnet 255.255.0.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
outside_map 20 ipsec-isakmp crypto map
card crypto outside_map 20 match address outside_cryptomap_20
card crypto outside_map pfs set 20 group2
card crypto outside_map 20 game peers X.X.X.X
outside_map crypto 20 card value transform-set ESP-AES-256-SHA
outside_map interface card crypto outside
ISAKMP allows outside
ISAKMP key * address X.X.X.X 255.255.255.255 netmask No.-xauth non - co
Nfig-mode
part of pre authentication ISAKMP policy 20
ISAKMP policy 20 aes-256 encryption
ISAKMP policy 20 chopping sha
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 8 X 00
Telnet X.X.X.X 255.255.255.0 outside
Telnet X.X.X.X 255.255.255.0 inside
Telnet admin_subnet 255.255.0.0 inside
Telnet timeout 30
ssh X.X.X.X 255.255.255.255 outside
X.X.X.X 255.255.255.0 inside SSH
SSH timeout 30
management-access inside
Console timeout 30
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd lease 3600
dhcpd ping_timeout 750
username password XXXXXX XXXXXXXXXXX encrypted privilege 15
Terminal width 80
Cryptochecksum:
: end

Hello Mark,

lol Nice to know that everything works fine now

Don't forget to mark it as answered and to classify the useful messages (if you don't know how to evaluate a message just to get to the bottom of each answer and mark 1 being a wrong answer, being a great answer 5 stars)

Kind regards

Julio

PD: Some kudos for you (because of the answer)

QoS is supported on the Cisco PIX 501 or 506th?

Hello

There is no mention of QoS in technical for the PIX 501 and 506 records but nothing for the 515. PIX OS 7.x configuration guides do not mention specific material support.

Does anyone know if QoS is taken care of in the 501 or 506th - I need support lines expectations for VoIP over IPSec.

Thank you

Chris

QoS is supported in 7.x code, you would have to level 501/506 to 7.x code, but this is not supported on these two models, the next logical solution would be to upgrade your PIX 501/506 to asa5505s.

Rgds

Jorge

PIX 501 10 User License

Does anyone know if the PIX 501 10 user license will limit the number of users can cross a site to site VPN that ends at the PIX?

Yes, it does, I encountered a problem with it myself in the past. The page at http://www.cisco.com/en/US/customer/products/hw/vpndevc/ps2030/products_data_sheet09186a0080091b18.html

It is said "the Cisco PIX 501 license 10 users supports up to 10 simultaneous source IP addresses for your internal network to browse the Cisco PIX 501.»

In my case what happened is that we had a VPN site-to-site created with a small office that adds a little more employees, everything was going well until the 11 IP address attempted to connect to a resource across the IPSec tunnel. We solved the problem by opting for a 50 user license.

PIX 501 for Cisco 3640 VPN router

-Start ciscomoderator note - the following message has been changed to remove potentially sensitive information. Please refrain from publishing confidential information about the site to reduce the risk to the security of your network. -end of the note ciscomoderator-

Have a 501 PIX and Cisco 3640 router. The 3640 is configured for dynamic map for VPN. The PIX 501 is set to pointing to the 3640 router static map. I can establish a tunnel linking the PIX to the router and telnet to a machine AIX on the inside network to the router. When I try to print on the network of the PIX 501 inside it fails.

What Miss me? I added the configuration for the PIX and the router.

Here are the PIX config:

PIX Version 6.1 (1)

ethernet0 nameif outside security0

nameif ethernet1 inside the security100

enable encrypted password xxxxxxxxxxxxxxxx

xxxxxxxxxxxxx encrypted passwd

pixfirewall hostname

fixup protocol ftp 21

fixup protocol http 80

fixup protocol h323 1720

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol smtp 25

fixup protocol sqlnet 1521

fixup protocol sip 5060

fixup protocol 2000 skinny

names of

pager lines 24

interface ethernet0 10baset

interface ethernet1 10full

Outside 1500 MTU

Within 1500 MTU

IP address outside dhcp setroute

IP address inside 192.168.1.1 255.255.255.0

alarm action IP verification of information

alarm action attack IP audit

PDM logging 100 information

history of PDM activate

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

Timeout xlate 0:05:00

Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

Timeout, uauth 0:05:00 absolute

GANYMEDE + Protocol Ganymede + AAA-server

RADIUS Protocol RADIUS AAA server

Enable http server

http 192.168.1.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

SNMP-Server Community public

No trap to activate snmp Server

enable floodguard

No sysopt route dnat

Telnet timeout 5

SSH timeout 5

dhcpd address 192.168.1.2 - 192.168.1.33 inside

dhcpd lease 3600

dhcpd ping_timeout 750

dhcpd outside auto_config

dhcpd allow inside

Terminal width 80

Cryptochecksum:XXXXXXXXXXXXXXXXXXX

: end

Here is the router config

Router #sh runn

Building configuration...

Current configuration: 6500 bytes

!

version 12.2

no service button

tcp KeepAlive-component snap-in service

a tcp-KeepAlive-quick service

horodateurs service debug datetime localtime

Log service timestamps datetime localtime

no password encryption service

!

router host name

!

start the flash slot1:c3640 - ik9o3s - mz.122 - 16.bin system

queue logging limit 100

activate the password xxxxxxxxxxxxxxxxx

!

clock TimeZone Central - 6

clock summer-time recurring CENTRAL

IP subnet zero

no ip source route

!

!

no ip domain-lookup

!

no ip bootp Server

inspect the name smtp Internet IP

inspect the name Internet ftp IP

inspect the name Internet tftp IP

inspect the IP udp Internet name

inspect the tcp IP Internet name

inspect the name DMZ smtp IP

inspect the name ftp DMZ IP

inspect the name DMZ tftp IP

inspect the name DMZ udp IP

inspect the name DMZ tcp IP

audit of IP notify Journal

Max-events of po verification IP 100

!

crypto ISAKMP policy 1

BA 3des

preshared authentication

Group 2

!

crypto ISAKMP policy 20

BA 3des

preshared authentication

Group 2

ISAKMP crypto key address x.x.180.133 xxxxxxxxxxx

ISAKMP crypto keys xxxxxxxxxxx address 0.0.0.0 0.0.0.0

!

!

Crypto ipsec transform-set esp-3des esp-sha-hmac vpn test

Crypto ipsec transform-set esp-3des esp-sha-hmac PIXRMT

!

dynamic-map crypto dny - Sai 25

game of transformation-PIXRMT

match static address PIX1

!

!

static-card 10 map ipsec-isakmp crypto

the value of x.x.180.133 peer

the transform-set vpn-test value

match static address of Hunt

!

map ISCMAP 15-isakmp ipsec crypto dynamic dny - isc

!

call the rsvp-sync

!

!

!

controller T1 0/0

framing ESF

linecode b8zs

Slots 1-12 channels-group 0 64 speed

Description controller to the remote frame relay

!

controller T1 0/1

framing ESF

linecode b8zs

Timeslots 1-24 of channel-group 0 64 speed

Description controller for internet link SBIS

!

interface Serial0/0:0

Description CKT ID 14.HXGK.785129 Frame Relay to Remote Sites

bandwidth 768

no ip address

no ip redirection

no ip unreachable

no ip proxy-arp

encapsulation frame-relay

frame-relay lmi-type ansi

!

interface Serial0 / point to point 0:0.17

Description Frame Relay to xxxxxxxxxxx location

IP unnumbered Ethernet1/0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

No arp frame relay

dlci 17 frame relay interface

!

interface Serial0 / point to point 0:0.18

Description Frame Relay to xxxxxxxxxxx location

IP unnumbered Ethernet1/0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

No arp frame relay

dlci 18 frame relay interface

!

interface Serial0 / point to point 0:0.19

Description Frame Relay to xxxxxxxxxxx location

IP unnumbered Ethernet1/0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

No arp frame relay

dlci 19 frame relay interface

!

interface Serial0 / point to point 0:0.20

Description Frame Relay to xxxxxxxxxxxxx location

IP unnumbered Ethernet1/0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

No arp frame relay

dlci 20 frame relay interface

!

interface Serial0 / point to point 0:0.21

Description Frame Relay to xxxxxxxxxxxx

IP unnumbered Ethernet1/0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

No arp frame relay

dlci 21 frame relay interface

!

interface Serial0 / point to point 0:0.101

Description Frame Relay to xxxxxxxxxxx

IP unnumbered Ethernet1/0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

No arp frame relay

dlci 101 frame relay interface

!

interface Serial0/1:0

CKT ID 14.HCGS.785383 T1 to ITT description

bandwidth 1536

IP address x.x.76.14 255.255.255.252

no ip redirection

no ip unreachable

no ip proxy-arp

NAT outside IP

inspect the Internet IP on

no ip route cache

card crypto ISCMAP

!

interface Ethernet1/0

IP 10.1.1.1 255.255.0.0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

no ip route cache

no ip mroute-cache

Half duplex

!

interface Ethernet2/0

IP 10.100.1.1 255.255.0.0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

no ip route cache

no ip mroute-cache

Half duplex

!

router RIP

10.0.0.0 network

network 192.168.1.0

!

IP nat inside source list 112 interface Serial0/1: 0 overload

IP nat inside source static tcp 10.1.3.4 443 209.184.71.138 443 extensible

IP nat inside source static tcp 10.1.3.4 9869 209.184.71.138 9869 extensible

IP nat inside source 10.1.3.2 static 209.184.71.140

IP nat inside source static 10.1.3.6 209.184.71.139

IP nat inside source static 10.1.3.8 209.184.71.136

IP nat inside source static tcp 10.1.3.10 80 209.184.71.137 80 extensible

IP classless

IP route 0.0.0.0 0.0.0.0 x.x.76.13

IP route 10.2.0.0 255.255.0.0 Serial0 / 0:0.19

IP route 10.3.0.0 255.255.0.0 Serial0 / 0:0.18

IP route 10.4.0.0 255.255.0.0 Serial0 / 0:0.17

IP route 10.5.0.0 255.255.0.0 Serial0 / 0:0.20

IP route 10.6.0.0 255.255.0.0 Serial0 / 0:0.21

IP route 10.7.0.0 255.255.0.0 Serial0 / 0:0.101

no ip address of the http server

!

!

PIX1 static extended IP access list

IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255

IP access-list extended hunting-static

IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255

extended IP access vpn-static list

ip permit 192.168.1.0 0.0.0.255 10.1.0.0 0.0.255.255

IP 192.0.0.0 allow 0.255.255.255 10.1.0.0 0.0.255.255

access-list 1 refuse 10.0.0.0 0.255.255.255

access-list 1 permit one

access-list 12 refuse 10.1.3.2

access-list 12 allow 10.1.0.0 0.0.255.255

access-list 12 allow 10.2.0.0 0.0.255.255

access-list 12 allow 10.3.0.0 0.0.255.255

access-list 12 allow 10.4.0.0 0.0.255.255

access-list 12 allow 10.5.0.0 0.0.255.255

access-list 12 allow 10.6.0.0 0.0.255.255

access-list 12 allow 10.7.0.0 0.0.255.255

access-list 112 deny ip host 10.1.3.2 everything

access-list 112 refuse ip 10.1.0.0 0.0.255.255 192.168.1.0 0.0.0.255

access-list 112 allow ip 10.1.0.0 0.0.255.255 everything

access-list 112 allow ip 10.2.0.0 0.0.255.255 everything

access-list 112 allow ip 10.3.0.0 0.0.255.255 everything

access-list 112 allow ip 10.4.0.0 0.0.255.255 everything

access-list 112 allow ip 10.5.0.0 0.0.255.255 everything

access-list 112 allow ip 10.6.0.0 0.0.255.255 everything

access-list 112 allow ip 10.7.0.0 0.0.255.255 everything

access-list 120 allow ip host 10.100.1.10 10.1.3.7

not run cdp

!

Dial-peer cor custom

!

!

!

!

connection of the banner ^ CCC

******************************************************************

WARNING - Unauthorized USE strictly PROHIBITED!

******************************************************************

^ C

!

Line con 0

line to 0

password xxxxxxxxxxxx

local connection

Modem InOut

StopBits 1

FlowControl hardware

line vty 0 4

exec-timeout 15 0

password xxxxxxxxxxxxxx

opening of session

!

end

Router #.

Add the following to the PIX:

> permitted connection ipsec sysopt

This indicates the PIX around all ACLs for IPsec traffic. Now that your IPSec traffic is still subject to the standard rules of PIX, so launched inside the traffic is allowed to go in, but off-initiated traffic is not.

VPN between cisco unified customer 3.6.3 and Pix 501 6.2 (1) with the MS CA server

Hello

I have Microsoft CA server with the latest support CEP and pix 501 that gets the digital certificate. I also have the client certificate of Cisco, but VPN doesn't work

In the IPSec Log Viewer, I constantly "CM_IKE_ESTABLISH_FAIL."

It worked well prior to Win2k server has been completely updated with the latest patches.

The pix configuration is identical to that of article http://www.cisco.com/warp/public/471/configipsecsmart.html

I reinstall the stand-alone CA and support CEP server but not had any luck.

What could be wrong?

It looks like IKE implementation problem. Make DH group 2 policy ISAKMP.

Visit this link:

http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_v53/IPSec/exvpncl.htm

default configuration of the pix 501 past recovery/restoration

You need to reset the PIX 501 (lost password). I tried the password recovery instructions and accesses the monitor command by using the connection of the console, but cannot get the file to be transferred using tftp (ping command also expires).

1. in case ordering interface be set to 0 or 1 (I used 1)

2. the order of the address I was using 192.168.1.1

3. order the server, I was using the IP address of the tftp server

4. entry door? (Which is the PIX or the computer)?

5. in addition to the blue console cable that if all other cables should be connected and which ports.

Thank you

I'm guessing you already have this document:

http://www.Cisco.com/en/us/customer/products/HW/vpndevc/ps2030/products_password_recovery09186a008009478b.shtml

I would like to use the default value inside of the interface of the 1. Connect a standard ethernet cable to one of the Interior ports on the PIX and the other to your PC that has the server tftp on it of the interface software. Make sure that you see a link on both ends light. If not, take this cable or save it if you think it is a crossover cable. If you set the PIX address to: 192.168.1.1, then I would set my tftp server address: 192.168.1.2 or something in the same subnet. In this way we will not care what is the gateway address. No need to let pesky routers get in the way, when we're down!

Since you asked the question 5 above, I'll explain. You should have a console cable connected, it seems do you since you can get to the monitor > prompt. You'll also need an ethernet cable plugged in a PC running a server tftp with the IP address: 192.168.1.2 3Com made a server tftp really good F * R * E * E.

http://support.3Com.com/software/utilities_for_windows_32_bit.htm

Select the last file in the list. Make sure you get that file recovery of password for the Cisco link above for the PIX OS version you are running. Configure the tftp server to point to the directory containing the PIX password recovery file and you are ready. Good luck, Derrick

Cisco PIX 501 to Cisco 3005 concentrator via remote access

Hello people,

I need your help.

We got a Cisco PIX 501 in one place and this pix is configured for pppoe connection. The pix connects to internet via the pppoe client. an official ip address ping works well.

So what I want to do is to establish a tunnel von between this pix and a cisco 3005 concentrator.

But I failed to establish it.

Here are the pix config. the acl? s are only for the test and will be replaced if it works.

6.3 (4) version PIX

interface ethernet0 10baset

interface ethernet1 100full

ethernet0 nameif outside security0

nameif ethernet1 inside the security100

activate the password xxx

passwd xxx

hostname PIX - to THE

domain araukraine.ua

fixup protocol dns-length maximum 512

fixup protocol ftp 21

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol http 80

fixup protocol they 389

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol sip 5060

fixup protocol sip udp 5060

fixup protocol 2000 skinny

fixup protocol smtp 25

fixup protocol sqlnet 1521

fixup protocol tftp 69

names of

outside ip access list allow a whole

inside_access_in ip access list allow a whole

pager lines 24

opening of session

Monitor logging warnings

logging warnings put in buffered memory

MTU outside 1456

MTU inside 1456

IP address outside pppoe setroute

IP address inside 192.168.x.x 255.255.255.0

alarm action IP verification of information

alarm action attack IP audit

PDM location 192.168.x.x 255.255.255.224 inside

forest warnings of PDM 500

history of PDM activate

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

outside access-group in external interface

inside_access_in access to the interface inside group

Timeout xlate 0:05:00

Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

Timeout, uauth 0:05:00 absolute

GANYMEDE + Protocol Ganymede + AAA-server

AAA-server GANYMEDE + 3 max-failed-attempts

AAA-server GANYMEDE + deadtime 10

RADIUS Protocol RADIUS AAA server

AAA-server RADIUS 3 max-failed-attempts

AAA-RADIUS deadtime 10 Server

AAA-server local LOCAL Protocol

the ssh LOCAL console AAA authentication

Enable http server

255.255.x.x 192.168.x.x http inside

No snmp server location

No snmp Server contact

SNMP-Server Community public

No trap to activate snmp Server

enable floodguard

255.255.x.x telnet inside 192.168.x.x

Telnet timeout 5

SSH 194.39.97.0 255.255.255.0 outside

SSH timeout 5

management-access inside

Console timeout 0

VPDN group pppoe_group request dialout pppoe

VPDN group pppoe_group localname [email protected] / * /

VPDN group ppp authentication pap pppoe_group

VPDN username [email protected] / * / password *.

encrypted privilege 15

vpnclient Server 212.xx.xx.xx

vpnclient mode network-extension-mode

vpntest vpngroup vpnclient password *.

vpnclient username pixtest password *.

Terminal width 80

the hub, I created a user pixtest, a group vpntest and I? ve created the rules of the network for example to what server, users behind the pix will be able to access.

And that? s all.

I couldn't send you exit pix or hub because I don't have an error or a message that the tunnel will be established.

What can be wrong?

Thanks for the replies

This configuration example shows how to create an IPsec tunnel to a computer that is running the Client VPN Cisco's (4.x and later versions) to a Cisco VPN concentrator 3000 to allow the user to safely access the network inside the VPN concentrator.

http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a008026f96c.shtml

PIX 501 and VPN Linksys router (WRV200)

I inherited a work where we have a Cisco PIX 501 firewall to a single site and Linksys WRV200 Router VPN on two other

sites. Asked me to connect these routers Linksys firewall PIX via the VPN.

According to me, the Linksys vpn routers can only connect via IPSec VPN, I'm looking for help on the configuration of the PIX 501 for the linksys to connect with the following, if possible.

Key exchange method: Auto (IKE)

Encryption: Auto, 3DES, AES128, AES192, AES256

Authentication: MD5

Pre Shared Key: xxx

PFS: Enabled

Life ISAKMP key: 28800

Life of key IPSec: 3600

The pix, I installed MDP and I tried to use the VPN wizard without result.

I chose the following settings when you make the VPN Wizard:

Type of VPN: remote VPN access

Interface: outside

Type of Client VPN device used: Cisco VPN Client

(can choose customer of Cisco VPN 3000, MS Windows Client by using the client MS Windows using L2TP, PPTP)

VPN clients group

Name of Group: RabyEstates

Pre Shared Key: rabytest

Scope of the Client authentication: disabled

Address pool

Name of the cluster: VPN - LAN

Starter course: 192.168.2.200

End of row: 192.168.2.250

Domain DNS/WINS/by default: no

IKE policy

Encryption: 3DES

Authentication: MD5

Diffie-Hellman group: Group 2 (1024 bits)

Transform set

Encryption: 3DES

Authentication: MD5

I have attached the log of the VPN Linksys router VPN.

This is the first time that I have ever worked with PIX so I'm still trying to figure the thing to, but I'm confident with the CCNA level network.

Thanks for your help!

Hello

Everything looks fine for me, try to have a computer in every network and ping between them. Check the newspapers/debug and fix them.

Let me know.

See you soon,.

Daniel

Reseting ipsec on PIX 501

Similar Questions

Maybe you are looking for