PIX 501 license

Similar Questions

• Pix 501 license limits and how to say

  I sent a PIX-501-BUN-K9, which is limited to 10 users. I recently sent another PC. I can't browse the internet unless I reboot the pix. Is this an indication that I need to update the license?

  What commands can I run on the pix to check or validate that I reached the limit license?

  You can enter:

  SH ver

  or

  SH - activation key

  This will display your license that is installed on your PIX. Next to "To inside hosts", you will see how many user licenses are available. You can upgrade by purchasing a license from 10 to 50 users (PIX-501-SW-10-50 =) for about $240, or 10 to unlimited (PIX-501-SW-10-UL =) for about $370.

  To find out how many are currently in use, you can enter "sho xlate count" which will set out how current translations are used.

  Please rate if this can help.

• PIX 501 10 User License

  Does anyone know if the PIX 501 10 user license will limit the number of users can cross a site to site VPN that ends at the PIX?

  Yes, it does, I encountered a problem with it myself in the past. The page at http://www.cisco.com/en/US/customer/products/hw/vpndevc/ps2030/products_data_sheet09186a0080091b18.html

  It is said "the Cisco PIX 501 license 10 users supports up to 10 simultaneous source IP addresses for your internal network to browse the Cisco PIX 501.»

  In my case what happened is that we had a VPN site-to-site created with a small office that adds a little more employees, everything was going well until the 11 IP address attempted to connect to a resource across the IPSec tunnel. We solved the problem by opting for a 50 user license.

• Connectivity random Cisco Pix 501

  Hello. I'm having some trouble with my CISCO PIX 501 Setup.

  A few months I started having random disconnects on my network (from inside to outside). The machines can ping the DC or the Pix, but impossible to surf the internet. The only way to make them go outside is a reboot of Pix.

  My configuration is:

  -----------

  See the ACE - pix config (config) #.
  : Saved
  : Written by enable_15 at 09:23:07.033 UTC Tuesday, June 3, 2014
  6.3 (3) version PIX
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 8Ry34retyt7RR564 encrypted password
  2fvbbfgdI.2KUOU encrypted passwd
  hostname as pix
  domain as.local
  fixup protocol dns-length maximum 512
  fixup protocol esp-ike
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol pptp 1723
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list acl_out permit icmp any one
  ip access list acl_out permit a whole
  access-list acl_out permit tcp any one
  Allow Access-list outside_access_in esp a whole
  outside_access_in list access permit udp any eq isakmp everything
  outside_access_in list of access permit udp any eq 1701 all
  outside_access_in list of access permit udp any eq 4500 all
  outside_access_in ip access list allow a whole
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  outside 10.10.10.2 IP address 255.255.255.0
  IP address inside 192.168.100.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  history of PDM activate
  ARP timeout 14400
  Global 1 10.10.10.8 - 10.10.10.254 (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Access-group outside_access_in in interface outside
  access to the interface inside group acl_out
  Route outside 0.0.0.0 0.0.0.0 10.10.10.1 0
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  RADIUS Protocol RADIUS AAA server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.10.2 255.255.255.255 inside
  http 192.168.10.101 255.255.255.255 inside
  http 192.168.100.2 255.255.255.255 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  ISAKMP nat-traversal 20
  Telnet timeout 5
  SSH 192.168.10.101 255.255.255.255 inside
  SSH timeout 60
  Console timeout 0
  dhcpd dns 8.8.8.8 8.8.4.4
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  Terminal width 80
  Cryptochecksum:7f9bda5e534eaeb1328ab08a3c4d28a
  ------------

  Do you have any advice? I don't get what's wrong with my setup.

  My DC is 192.168.100.2 and the network mask is 255.255.255.0

  The network configuration is configured to set the IP of the gateway to 192.168.100.1 (i.e. the PIX 501).

  I have about 50 + peers on the internal network.

  Any help is apprecciate.

  Hello

  You have a license for 50 users +?

  After the release of - Show version

  RES

  Paul

• How to configure the PPPoE on PIX 501?

  Mailto: [email protected] / * /

  MSN: [email protected] / * /

  According to the below URL Cisco TAC:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00801055dd.shtml

  but I always failed. And my PIX 501 Configuration noted below:

  pixfirewall # write terminal

  Building configuration...

  : Saved

  :

  6.3 (1) version PIX

  interface ethernet0 10baset

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable password xxxx

  passwd xxxx

  pixfirewall hostname

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  names of

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside pppoe setroute

  IP address inside 192.168.1.254 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route inside 10.0.0.0 255.0.0.0 192.168.1.1 1

  Route inside 20.0.0.0 255.0.0.0 192.168.1.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  VPDN group pppoex request dialout pppoe

  Cisco localname VPDN group pppoex

  VPDN group ppp authentication pap pppoex

  VPDN username xxxx password *.

  Terminal width 80

  Cryptochecksum:xxxx

  : end

  [OK]

  See the pixfirewall version #.

  Cisco PIX Firewall Version 6.3 (1)

  Cisco PIX Device Manager Version 1.1 (2)

  Updated Thursday 19 March 03 11:49 by Manu

  pixfirewall until 58 mins 6 dry

  Material: PIX - 501, 16 MB RAM, 133 MHz Am5x86 CPU

  Flash E28F640J3 @ 0 x 3000000, 8 MB

  BIOS Flash E28F640J3 @ 0xfffd8000, 128KB

  0: ethernet0: the address is 000b.fd58.886b, irq 9

  1: ethernet1: the address is 000b.fd58.886c, irq 10

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Maximum Interfaces: 2

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: 50

  Throughput: unlimited

  you have all the debugging logs?

• Pix 501 connection problems

  I am very new to cisco equipment and I was wondering if someone could help me with this (probably very simple question).

  When connecting to my pix via the browser (https://192.168.1.1/startup.html), the browser never took the start screen with the message that says "loading, please wait." This leads me to believe that the firewall is rejecting connections from my machine (which uses dhcp to get an ip address of the pix).

  To work around this problem, I tried to connect to the CLI using hyperterminal. I can connect and run a few basic commands as 'show version', but cannot log on as a user with permissions.

  If the web interface has a default connection of void & empty, surely the cli should be the same?

  Is anyone able to tell me what is the default login, so that I can start confguring the pix via the cli?

  Thanks in advance.

  Justin Spencer.

  Please see below for info pix:

  Cisco PIX Firewall Version 6.3 (3)

  Cisco PIX Device Manager Version 3.0 (1)

  Updated Thursday, August 13 03 13:55 by Manu

  pixfirewall until 12 minutes 18 seconds

  Material: PIX - 501, 16 MB RAM, 133 MHz Am5x86 CPU

  Flash E28F640J3 @ 0 x 3000000, 8 MB

  BIOS Flash E28F640J3 @ 0xfffd8000, 128KB

  0: ethernet0: the address is 0011.937e.0486, irq 9

  1: ethernet1: the address is 0011.937e.0487, irq 10

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  The maximum physical Interfaces: 2

  Maximum Interfaces: 2

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal guests: 10

  Throughput: unlimited

  Peer IKE: 10

  This PIX has a restricted license (R).

  Serial number: 808301473 (0x302db3a1)

  Activation key running: 0xb53be54d 0x26da18f9 0xb2b78cef 0x8fe1abb6

  Configuration changed from enable_1 to 15:36:42.554 UTC, Monday, November 8, 2004

  pixfirewall >

  long live java.

  Please this mark as resolved, others won't waste time.

  Thank you

• Number of VPN clients behind a PIX 501, restriction?

  Is there a restriction in the number of VPN clients can be behind a PIX 501. Is is just limited by the number of hosts (10, 50, Unlimited)?

  Hello

  Behind a PIX VPN clients. Will you use NAT - T (must). It will be limited only to the number of users (normal users) through the PIX. So if you have a license to use 10 or 50 then the VPN connection is counted in this list.

  Connection VPN Client through PIX is not IKE tunnel. They are normal UDP500 and UDP4500 peers.

  Vikas

• PIX 501 and THE, 3DES, AES

  For a version newly produced PIX 501,

  (1) are DES, 3DES and AES activation keys all pre-installed?

  (2) how I can find on which of them is pre-installed on my PIX 501?

  (3) when I create a server VPN (on the PIX 501), I see that all three OF THEM, 3DES and AES are available in the drop-down list of the PDM configuration screen. Does that mean my PIX 501 have all three of them (FROM THE, 3DES and AES)? -If the answer is no, assume that only is preinstalled on PIX 501, then why/how can appear in the drop-down list the 3DES and AES?

  Thank you for helping.

  Scott

  Should be integrated already. depends on the way the news is your PIX 501.

  To be sure to log in to the console and type:

  See the version

  See the example output version:

  See the pixfirewall version (config) #.

  Cisco PIX Firewall Version 6.2 (3)

  Cisco PIX Device Manager Version 2.0 (1)

  Updated Thursday April 17 02 21:18 by Manu

  pixdoc515 up to 9 days 3 hours

  Material: PIX - 515, 64 MB RAM, Pentium 200 MHz processor

  I28F640J5 @ 0 x 300 Flash, 16 MB

  BIOS Flash AT29C257 @ 0xfffd8000, 32 KB

  0: ethernet0: the address is 0050.54ff.3772, irq 10

  1: ethernet1: the address is 0050.54ff.3773, irq 7

  2: ethernet2: the address is 00d0.b792.409d, irq 11

  Features licensed:

  Failover: enabled

  VPN - A: enabled

  VPN-3DES: enabled

  Maximum Interfaces: 6

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: unlimited

  Throughput: unlimited

  Peer IKE: unlimited

  Serial number: 480221353 (0x1c9f98a9)

  Activation key running: 0x36df4255 0x246dc5fc 0x39d2ec4d 0x09f6288f

  Modified configuration of enable_15 to 12:15:28.311 UTC Wednesday, may 1, 2002

  pixfirewall (config) #.

  Here, you should see if THE or 3DES, AES encryption is active or not. If you have just SOME so you can use the following link and get for free a new activation key that allows 3DES and AES.

  https://Tools.Cisco.com/swift/licensing/JSP/formGenerator/Pix3DesMsgDisplay.jsp

  sincerely

  Patrick

• PIX 501 basic Config

  I'm putting in place an internet service for some members of the service here in Afghanistan. We use the commercial internet (provided by satellite) to a modem that goes into my firewall 501 pix.

  Service that we bought gives us Ip 29, and now I just have it set up as such.

  Modem gateway: 10.124.48.1

  Outside the firewall: 10.124.48.2

  Inside the firewall: 192.168.1.1

  Global NAT pool: 10.124.48.3 30 (the rest of intellectual property s that are outside the package)

  On the inside of the pool of the host: 192.168.1.2 -.33

  DNS for inside customers: 192.168.130.30,.50

  Everything seems ok, as I use the PDM software to allow all traffic ip from outside to inside (I know it isn't the safest to do thing ~ and the fact that I turned a firewall $ 700 to a router for $40). I can browse the internet, but it is really weird.

  I.E.

  I can ping msn.com and www.msn.com , and it resolves the twice,

  But if I put msn.com in Internet explorer, it says cannot display the page, but if I hit the refresh like five times, it'll happen. If I navigate away from the page and then try to type in msn.com again (in the same window) I hit refresh 5 times, to get the next page.

  But if I type in www.msn.com it just generally well upward.

  Even when he says that the page cannot be displayed, I have her pinger running in background ~ so I know that I can get for it. Weird huh?

  I also have a question about licenses. When I get the pix firewall information, it says inside hosts: 10 but he let's have me 32 s ip for inside hosts. Does this mean that I'm having problems when I have more than 10 users browsing through the firewall? Or is that what I have as many hosts ip s?

  Thanks in advance for any assistance.

  1.) to refine the 10 limitation of host within the network you couold install another device inside network that PAT - translation of Port addresses that hide all the IP addresses behind his foreign address.

  All PC-> [device router/PAT] - [PIX Firewall] - [router]-> Internet

  (2.) to buy/pbtain a license longer write a mail to:

  mailto:[email protected] / * /

  The product update:

  PIX-501-SW-10-50 = software upgrade license for 501 10 to 50 users PIX = approximately 340$ US

  PIX-501-SW-10-UL = software upgrade license for the 501 user 10-for-unlimited PIX = about 400$ US

  3.) World normal political deadlock depends on your company security policy, someone should set one, many companys trust their employees and allow all outgoing traffic. Might be good to block traffic P2P, Multimedia Streaming stuff, but this is not possible with OS 6.3.4 Release. You must wait for PIX OS 7.0, which is not available for PIX 501.

  sincerely

  Patrick

• Adding a pix 501 VPN 2

  Hello.. I am beginner in this kind of things cisco...

  I'm trying to set up multiple VPN on a Cisco PIX 501 firewall with routers Linksys BEFVP41...

  Since not very familiar with the CLI, I use the PDM utility and it was very easy for the first... Unfortunately, I get this error when I try to add the second VPN using the VPN Wizard:

  Outside_map map (ERR) crypto set peer 200.20.10.3

  WARNING: This encryption card is incomplete

  To remedy the situation even and a list of valid to add this encryption card

  Hi garcia

  for each vpn/peer, you need to a separate instance of crypto card, the card will have the same name, but different sequence... numbers one map encryption can be attributed to an interface, but you can have several instance of cards inside a main...

  for configuration, you can go through the URL below... It has all the details on IPSEC config:

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_63/config/ipsecint.htm

  I hope this helps... all the best... the rate of responses if deemed useful...

  REDA

• Microsoft secondary authority w / Cisco router / PIX 501

  I'm trying to get digital certificates to work on my 2621XM router. I have also

  need to put in place on the three firewalls PIX 501 but who have not obtained until now still. I have

  don't have no access to the CA root, but it could bring in line if I had to. I have

  have a stand-alone Microsoft subordinate CA that I want to use to publish all

  certificates.

  Is it possible, as well with the router and the firewall? If so, what version

  the IOS do I need? I installed the add-on CEP at HQ. I can't

  It works and I'm starting to wonder if it is still possible. If this doesn't

  work, how can I make it work? I have all the documents that Cisco has combed

  on the subject and have gotten nowhere.

  Any help would be greatly appreciated. Thank you.

  Jennnette,

  I sent this document, let me know how it goes or if you have any questions.

  Kurtis Durrett

• PIX 501 Logging

  I would like to open a session of hacking and intrusion of the attacks through a PIX 501 with a connection to broadband in a Home Office Setup. I have the camera upwards and the race and I am currently Setup with the Kiwi Syslog Dameon. What would be my best approach Logging all relevant information with the load to the bottom of the unit? Any suggestions / tips would be appreciated.

  Thank you

  It is a common logging configuration that I use:

  opening of session

  timestamp of the record

  logging trap information

  host of logging inside x.x.x.x

  No registration message 106015

  No message logging 106007

  No message logging 105003

  No registration message 105004

  No message recording 309002

  No message logging 305012

  No registration message 305011

  No message logging 303002

  No message logging 111008

  No message logging 302015

  No message recording 302014

  No message logging 302013

  No registration message 304001

  No message logging 111005

  No message logging 609002

  No message recording 609001

  No message logging 302016

  I usually do not enable the logging buffer (never use connection console it will affect performance) because it's not the messages timestamp (it only timestamps in the syslog). But the PIX loaded down with the load, you and Kiwi you before the PIX don't.

  Also turn on the IDs on the PIX.

  It will be useful.

  Steve

• Configure the PIX 501 for IDS

  I have a PIX 501 with wired high-speed LAN headquarters inside and outside. Which would be a solid policy IDS to enable and what interfaces it must be applied to? There will be other measures necessary to enable IDS?

  IDS on the PIX itself is very limited, it checks only 59 signatures listed here (http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_62/cmdref/gl.htm#xtocid9 under the section of signatures supported IDS). The signatures themselves are pretty basic.

  If you do not want to activate this, then for the signatures of attacks I would fix for drop/alarm/reset action, which is the default anyway.

  You will also need to set the logging to a syslog server and monitoring for any 4000nn messages in syslog, cause it event IDS.

• PIX 501, 1 static IP, IP address dynamic 2. Mesh full possible?

  I have 3 sites. All sites have PIX 501. Central site has a static IP, 2 remote sites a dynamic IP.

  I have no problem with the connection to the central site by using their dynamic IP address in a remote star connection.

  Is it possible for 2 remote sites communicate? There is data that must be transferred between remote sites. I read somewhere in cisco site web which its possible via mesh on request.

  Does anyone have an example of configuration on a VPN Site to Site where the Central site has static IP and remote sites with a dynamic IP? Remote locations teaches a dynamic IP from remote sites to the central server.

  Thank you.

  With IOS as your hub and then the Yes rays, the rays can learn dynamically address other departments using the PNDH. This type of configuration is called Dynamic Multipoint VPN (DMVPN), you can read everything you need to know about this here:

  http://www.Cisco.com/warp/public/105/DMVPN.html

  Even with EzVPN (not DMVPN) the rays will not learn the address of other rays, all communication is always via the hub. Call another talks would work, but as I said, the packages will talk-star.

• Opening of port 22 in PIX 501

  I would like to access my PC location xyz. How can I open port 22 access to my pc. I use pix 501.

  Can anyone provide commands to open the port so that I can access my pc.

  Thank you

  totally agree because only 3 commands are needed.

  list of allowed inbound tcp access any eq 22

  public static tcp (indoor, outdoor) interface 22 22 netmask 255.255.255.255 0 0

  clear xlate

  However, all of these commands are missing in the config you have posted.