Unable to connect to PDM on PIX 501

Similar Questions

• Unable to retrieve the password on PIX 501 - TFTP failed (return: arg:0 x 0-1)

  In the course of a merger of office, we got a PIX 501. It is obviously been configured but nobody is anywhere knows anything and there is no documentation regarding the config not found. As a result, I tried to retrieve the password so that we can reconfigure and reuse it for our purposes. I followed the instructions on the cisco.com web site but get the error message:

  TFTP failed (return: arg:0 x 0-1)

  I tested the connectivity between the PIX and TFTP server and it works. I can post a txt file that is captured is of no help.

  Any ideas as to what I am doing wrong or, more importantly, how the address so that I can recover the password. Certainly, it is the first time that I have worked on a PIX.

  Thanks in advance for any help.

  Sergio

  Sergio,

  Depends on when you received the pix. I'll try with the code 6.1 and 6.2. Thank you

  Renault

• L2l IPSec VPN 3000 and PIX 501

  Hello

  I have a remote site that has a broadband internet connection and uses a PIX 501.  We wanted to connect them with our main office using our VPN 3000 via VPN site-to-site.

  I followed the following documentation:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml#tshoot

  However the L2L session does not appear on the hub when I check the active sessions.

  The network diagram, as well as the PIX config and the screenshots of the VPN configuration for the IPSec-L2L tunnel is attached.

  Any help or advice are appreciated.

  I just noticed that the PIX firewall, the phase 1 paramateres are not configured. You must configure the same PASE 1 and phase 2 settings on both ends of the tunnel.

  For example, on CVPN 3000, you have configured settings Phase 1 as 3DES, pre-shared key etc... We have the same configuration on the PIX firewall too.

  Here is an example of sample config

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml

  I hope this helps!

• Connectivity random Cisco Pix 501

  Hello. I'm having some trouble with my CISCO PIX 501 Setup.

  A few months I started having random disconnects on my network (from inside to outside). The machines can ping the DC or the Pix, but impossible to surf the internet. The only way to make them go outside is a reboot of Pix.

  My configuration is:

  -----------

  See the ACE - pix config (config) #.
  : Saved
  : Written by enable_15 at 09:23:07.033 UTC Tuesday, June 3, 2014
  6.3 (3) version PIX
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 8Ry34retyt7RR564 encrypted password
  2fvbbfgdI.2KUOU encrypted passwd
  hostname as pix
  domain as.local
  fixup protocol dns-length maximum 512
  fixup protocol esp-ike
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol pptp 1723
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list acl_out permit icmp any one
  ip access list acl_out permit a whole
  access-list acl_out permit tcp any one
  Allow Access-list outside_access_in esp a whole
  outside_access_in list access permit udp any eq isakmp everything
  outside_access_in list of access permit udp any eq 1701 all
  outside_access_in list of access permit udp any eq 4500 all
  outside_access_in ip access list allow a whole
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  outside 10.10.10.2 IP address 255.255.255.0
  IP address inside 192.168.100.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  history of PDM activate
  ARP timeout 14400
  Global 1 10.10.10.8 - 10.10.10.254 (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Access-group outside_access_in in interface outside
  access to the interface inside group acl_out
  Route outside 0.0.0.0 0.0.0.0 10.10.10.1 0
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  RADIUS Protocol RADIUS AAA server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.10.2 255.255.255.255 inside
  http 192.168.10.101 255.255.255.255 inside
  http 192.168.100.2 255.255.255.255 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  ISAKMP nat-traversal 20
  Telnet timeout 5
  SSH 192.168.10.101 255.255.255.255 inside
  SSH timeout 60
  Console timeout 0
  dhcpd dns 8.8.8.8 8.8.4.4
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  Terminal width 80
  Cryptochecksum:7f9bda5e534eaeb1328ab08a3c4d28a
  ------------

  Do you have any advice? I don't get what's wrong with my setup.

  My DC is 192.168.100.2 and the network mask is 255.255.255.0

  The network configuration is configured to set the IP of the gateway to 192.168.100.1 (i.e. the PIX 501).

  I have about 50 + peers on the internal network.

  Any help is apprecciate.

  Hello

  You have a license for 50 users +?

  After the release of - Show version

  RES

  Paul

• PIX 506 - cannot connect to PDM more

  We have a PIX 506 in a test environment that has been configured in the past using Netscape. Now when we try to connect via https, Netscape says "unable to connect to the server (TCP error: i/o error). The PIX is version 6.1 (1) and PDM is 1.0 (2). I can connect via telnet and change the configuration, but I was not able to get the connection Internet work anymore.

  I captured the connection with ethereal and I see 3 packets, the connection, then the client sends a SSLv2 Client Hello, then the PIX closes the connection. When I dump the telnet configuration, I get:

  Enable http server

  ClientName http 255.255.255.255 inside

  where clientname is defined above in the name and the entries of "place of pdm.

  The PDM installation guide has a troubleshooting section, and it says to make sure the clock is set to UTC. "show clock" indicates the time and date, but no area is listed.

  You have changed the IP address on the PIX interface at some point? If so, try to regenerate public/private key pairs. Fox

  > ca related rsa

  > key gen rsa 512 AC

  > ca save all

  or you can just run the command 'setup' from config mode and it'll do all that for you. Then try to reconnect.

• Customer Cisco PIX 501 VPN connects but no connection to the local network

  Hi all:

  I am able to make a VPN connection to a PIX 501. The remote client is assigned an IP (192.168.2.1) also, but not able to access all the machines in the local network connected to the PIX.

  I have attached the PIX configuration.

  Advice will be greatly appreciated.

  ********************

  6.3 (5) PIX version

  interface ethernet0 car

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable password xxxx

  passwd xxxxx

  pixfirewall hostname

  domain ciscopix.com

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  access-list 102 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside dhcp setroute

  IP address inside 192.168.1.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool ippool 192.168.2.1 - 192.168.2.5

  location of PDM 192.168.2.0 255.255.255.0 outside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) - 0 102 access list

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  ISAKMP allows outside

  ISAKMP identity address

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup vpn3000 ippool address pool

  vpngroup vpn3000 Server dns 68.87.72.130

  vpngroup vpn3000-wins 192.168.1.100 Server

  vpngroup vpn3000 split tunnel 101

  vpngroup vpn3000 downtime 1800

  password vpngroup vpn3000 *.

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd address 192.168.1.2 - 192.168.1.33 inside

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:xxxx

  ****************

  The DNS server is the one assigned to me by my ISP.

  My internal network connected to the PIX is 192.168.1.1 - 192.168.1.33 and the VPN ip pool is 192.168.2.1 - 192.168.2.5

  "isakmp nat-traversal 20" can do the trick.

• Pix 501 connection problems

  I am very new to cisco equipment and I was wondering if someone could help me with this (probably very simple question).

  When connecting to my pix via the browser (https://192.168.1.1/startup.html), the browser never took the start screen with the message that says "loading, please wait." This leads me to believe that the firewall is rejecting connections from my machine (which uses dhcp to get an ip address of the pix).

  To work around this problem, I tried to connect to the CLI using hyperterminal. I can connect and run a few basic commands as 'show version', but cannot log on as a user with permissions.

  If the web interface has a default connection of void & empty, surely the cli should be the same?

  Is anyone able to tell me what is the default login, so that I can start confguring the pix via the cli?

  Thanks in advance.

  Justin Spencer.

  Please see below for info pix:

  Cisco PIX Firewall Version 6.3 (3)

  Cisco PIX Device Manager Version 3.0 (1)

  Updated Thursday, August 13 03 13:55 by Manu

  pixfirewall until 12 minutes 18 seconds

  Material: PIX - 501, 16 MB RAM, 133 MHz Am5x86 CPU

  Flash E28F640J3 @ 0 x 3000000, 8 MB

  BIOS Flash E28F640J3 @ 0xfffd8000, 128KB

  0: ethernet0: the address is 0011.937e.0486, irq 9

  1: ethernet1: the address is 0011.937e.0487, irq 10

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  The maximum physical Interfaces: 2

  Maximum Interfaces: 2

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal guests: 10

  Throughput: unlimited

  Peer IKE: 10

  This PIX has a restricted license (R).

  Serial number: 808301473 (0x302db3a1)

  Activation key running: 0xb53be54d 0x26da18f9 0xb2b78cef 0x8fe1abb6

  Configuration changed from enable_1 to 15:36:42.554 UTC, Monday, November 8, 2004

  pixfirewall >

  long live java.

  Please this mark as resolved, others won't waste time.

  Thank you

• PIX 501 no connectivity to wide band

  Hey,.

  Just got a pix 501 to put in the office, the problem is, I went through the automatic configuration wizerd and looked in the settings, online, that I can't seem to see dchp outgoing connetion. Is there a setting Im missing. When I hit so he could refresh ip he tells me he cant and frankly Im lost I have a N + so I some knowlage of the installer, but it seems to be difficult to find info on this box anyone help or point me in the right direction on how to get online connectivity.

  thamk you for your time

  William,

  That mark it as resolved!

  This is your post not mine.

  ;-)

• PIX 501 PPPoE w / static NAT loss of connectivity

  I have a {should} installation very simple. PIX 501 with PPPoE on the external interface, 3 inside customers using PAT and 1 inside the client I am trying to use an address mapping static on permit communications with this host from the outside using a particular service. I did a lot of these before where there was an ADSL router in front of the PIX, but this is the first where I've used the PIX as the PPPoE client. When I use the static NAT for the single host it loses all connectivity beyond the PIX outside interface. When I get rid of the static mapping, through PAT very well. I spent many hours troubleshooting and control a lot of obvious things, but I am at a loss right now... unless it could be a problem with the IP address that has been assigned by the ISP for use with static NAT. Any thoughts on this would be greatly appreciated.

  Thank you

  Sorry, in your case that static would look like this because of the dynamic IP.

  static (inside, outside) 23 interface 10.1.1.1 23 netmask 255.255.255.255

  Daniel

• A PIX 501 can connect to a VPN service?

  Can a PIX 501 6.3 (4) establish a VPN to a supplier like www.privateinternetaccess.com?  They claim to support PPTP and L2TP/IPSEC.  If so, how the PIX should be configured?

  Thank you.

  No, none of the networking gear (Inc. ASA) can be configured as PPTP and L2TP over IPSec client client.

  Both are PC or MAC software.

• PIX 501 NAT and PAT with a single IP address

  Using the following configuration, on my first PIX 501, I am unable to provide a server of mail to the outside world and allows inside customers to browse the Internet. :

  6.3 (5) PIX version

  interface ethernet0 car

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable password xxxx

  passwd xxx

  hostname fw-sam-01

  SAM domain name

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  No fixup not protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  outside access list permit tcp any host 62.x.x.109 eq smtp

  access the inside to allow tcp a whole list

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside the 62.177.x.x.x.255.248

  IP address inside 192.168.45.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 192.168.45.2 255.255.255.255 inside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  public static 62.177.x.x.x.45.2 (Interior, exterior) mask subnet 255.255.255.255 0 0

  outside access-group in external interface

  group-access to the Interior in the interface inside

  Route outside 0.0.0.0 0.x.x.x.177.208.105 1

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.45.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Telnet 192.168.45.0 255.255.255.0 inside

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd lease 3600

  dhcpd ping_timeout 750

  : end

  It is I'am using access list and groups wrong or am I wrong in PAT/NAT configuration.

  Please advise...

  Hello

  I went through the ongoing discussion. The pix configuration should be fine for now according to suggestions. The problems seems to be on the server. If it is a new installation of windows, then there is an option not to accept requests that are not local network.

  If you want to check if pix allows connections and then when you telnet to port 25 of the outside, just run the xlates control.

  SH xlate and it should show you a translation for the inside host. More than a quick test if pix allows traffic is to check 'sho-outdoor access list' and see if the counters are increasing.

  Hopefully this should help you.

  Arun S.

• IPSec VPN pix 501 no LAN access

  I'm trying to set up an IPSec VPN in a basic small business scenario. I am able to connect to my pix 501 via IPSec VPN and browse the internet, but I am unable to ping or you connect to all devices in the Remote LAN. Here is my config:

  : Saved

  :

  6.3 (3) version PIX

  interface ethernet0 car

  interface ethernet1 100full

  nameif ethernet0 WAN security0

  nameif ethernet1 LAN security99

  enable encrypted password xxxxxxxxxxxxx

  xxxxxxxxxxxxxxxxx encrypted passwd

  host name snowball

  domain xxxxxxxxxxxx.local

  clock timezone PST - 8

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol pptp 1723

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  No fixup not protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  acl_in list of access permit udp any any eq field

  acl_in list of access permit udp any eq field all

  acl_in list access permit tcp any any eq field

  acl_in tcp allowed access list any domain eq everything

  acl_in list access permit icmp any any echo response

  access-list acl_in allow icmp all once exceed

  acl_in list all permitted access all unreachable icmp

  acl_in list access permit tcp any any eq ssh

  acl_in list access permit tcp any any eq www

  acl_in tcp allowed access list everything all https eq

  acl_in list access permit tcp any host 192.168.5.30 eq 81

  acl_in list access permit tcp any host 192.168.5.30 eq 8081

  acl_in list access permit tcp any host 192.168.5.22 eq 8081

  acl_in list access permit icmp any any echo

  access-list acl_in permit tcp host 76.248.x.x a

  access-list acl_in permit tcp host 76.248.x.x a

  allow udp host 76.248.x.x one Access-list acl_in

  access-list acl_out permit icmp any one

  ip access list acl_out permit a whole

  acl_out list access permit icmp any any echo response

  acl_out list access permit icmp any any source-quench

  allowed any access list acl_out all unreachable icmp

  access-list acl_out permit icmp any once exceed

  acl_out list access permit icmp any any echo

  Allow Access-list no. - nat icmp a whole

  access-list no. - nat ip 192.168.5.0 allow 255.255.255.0 172.16.0.0 255.255.0.0

  access-list no. - nat ip 172.16.0.0 allow 255.255.0.0 any

  access-list no. - nat permit icmp any any echo response

  access-list no. - nat permit icmp any any source-quench

  access-list no. - nat icmp permitted all all inaccessible

  access-list no. - nat allow icmp all once exceed

  access-list no. - nat permit icmp any any echo

  pager lines 24

  MTU 1500 WAN

  MTU 1500 LAN

  IP address WAN 65.74.x.x 255.255.255.240

  address 192.168.5.1 LAN IP 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool pptppool 172.16.0.2 - 172.16.0.13

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global (WAN) 1 interface

  NAT (LAN) - access list 0 no - nat

  NAT (LAN) 1 0.0.0.0 0.0.0.0 0 0

  static (LAN, WAN) 65.x.x.37 192.168.5.10 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.36 192.168.5.20 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.38 192.168.5.30 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.39 192.168.5.40 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.42 192.168.5.22 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.43 192.168.5.45 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.44 192.168.5.41 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.45 192.168.5.42 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.46 192.168.5.44 netmask 255.255.255.255 0 0

  static (LAN, WAN) 65.x.x.41 192.168.5.21 netmask 255.255.255.255 0 0

  acl_in access to the WAN interface group

  access to the LAN interface group acl_out

  Route WAN 0.0.0.0 0.0.0.0 65.x.x.34 1

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  NTP server 72.14.188.195 source WAN

  survey of 76.248.x.x WAN host SNMP Server

  location of Server SNMP Sacramento

  SNMP Server contact [email protected] / * /

  SNMP-Server Community xxxxxxxxxxxxx

  SNMP-Server enable traps

  enable floodguard

  the string 1 WAN fragment

  Permitted connection ipsec sysopt

  Sysopt connection permit-pptp

  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  client configuration address map mymap crypto initiate

  client configuration address map mymap crypto answer

  card crypto mymap WAN interface

  ISAKMP enable WAN

  ISAKMP nat-traversal 20

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup myvpn address pptppool pool

  vpngroup myvpn Server dns 192.168.5.44

  vpngroup myvpn by default-field xxxxxxxxx.local

  vpngroup split myvpn No. - nat tunnel

  vpngroup idle 1800 myvpn-time

  vpngroup myvpn password *.

  Telnet 192.168.5.0 255.255.255.0 LAN

  Telnet timeout 5

  SSH 192.168.5.0 255.255.255.0 LAN

  SSH timeout 30

  Console timeout 0

  VPDN group pptpusers accept dialin pptp

  VPDN group ppp authentication pap pptpusers

  VPDN group ppp authentication chap pptpusers

  VPDN group ppp mschap authentication pptpusers

  VPDN group ppp encryption mppe 128 pptpusers

  VPDN group pptpusers client configuration address local pptppool

  VPDN group pptpusers customer 192.168.5.44 dns configuration

  VPDN group pptpusers pptp echo 60

  VPDN group customer pptpusers of local authentication

  VPDN username password xxx *.

  VPDN username password xxx *.

  VPDN enable WAN

  dhcpd address 192.168.5.200 - 192.168.5.220 LAN

  dhcpd 192.168.5.44 dns 8.8.8.8

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd enable LAN

  username privilege 0 encrypted password xxxxxxxxxx xxxxxxxxxxx

  username privilege 0 encrypted password xxxxxxxxxx xxxxxxxxxxx

  Terminal width 80

  Cryptochecksum:xxxxxxxxxxxxxxxxxx

  : end

  I'm sure it has something to do with NAT or an access list, but I can't understand it at all. I know it's a basic question, but I would really appreaciate help!
  Thank you very much
  Trevor

  "No. - nat' ACL doesn't seem correct, please make sure you want to remove the following text:

  do not allow any No. - nat icmp access list a whole

  No No. - nat ip 172.16.0.0 access list allow 255.255.0.0 any

  No No. - nat access list permit icmp any any echo response

  No No. - nat access list permit icmp any any source-quench

  No No. - nat access list permit all all unreachable icmp

  No No. - nat access list do not allow icmp all once exceed

  No No. - nat access list only allowed icmp no echo

  You must have 1 line as follows:

  access-list no. - nat ip 192.168.5.0 allow 255.255.255.0 172.16.0.0 255.255.0.0

  Please 'clear xlate' after the changes described above.

  In addition, if you have a personal firewall enabled on the host you are trying to connect from the Client VPN, please turn it off and try again. Personal firewall of Windows normally blocks the traffic of different subnets.

  Hope that helps.

• PIX 501 for Cisco 3640 VPN router

  -Start ciscomoderator note - the following message has been changed to remove potentially sensitive information. Please refrain from publishing confidential information about the site to reduce the risk to the security of your network. -end of the note ciscomoderator-

  Have a 501 PIX and Cisco 3640 router. The 3640 is configured for dynamic map for VPN. The PIX 501 is set to pointing to the 3640 router static map. I can establish a tunnel linking the PIX to the router and telnet to a machine AIX on the inside network to the router. When I try to print on the network of the PIX 501 inside it fails.

  What Miss me? I added the configuration for the PIX and the router.

  Here are the PIX config:

  PIX Version 6.1 (1)

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable encrypted password xxxxxxxxxxxxxxxx

  xxxxxxxxxxxxx encrypted passwd

  pixfirewall hostname

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 1720

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  names of

  pager lines 24

  interface ethernet0 10baset

  interface ethernet1 10full

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside dhcp setroute

  IP address inside 192.168.1.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  No sysopt route dnat

  Telnet timeout 5

  SSH timeout 5

  dhcpd address 192.168.1.2 - 192.168.1.33 inside

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:XXXXXXXXXXXXXXXXXXX

  : end

  Here is the router config

  Router #sh runn

  Building configuration...

  Current configuration: 6500 bytes

  !

  version 12.2

  no service button

  tcp KeepAlive-component snap-in service

  a tcp-KeepAlive-quick service

  horodateurs service debug datetime localtime

  Log service timestamps datetime localtime

  no password encryption service

  !

  router host name

  !

  start the flash slot1:c3640 - ik9o3s - mz.122 - 16.bin system

  queue logging limit 100

  activate the password xxxxxxxxxxxxxxxxx

  !

  clock TimeZone Central - 6

  clock summer-time recurring CENTRAL

  IP subnet zero

  no ip source route

  !

  !

  no ip domain-lookup

  !

  no ip bootp Server

  inspect the name smtp Internet IP

  inspect the name Internet ftp IP

  inspect the name Internet tftp IP

  inspect the IP udp Internet name

  inspect the tcp IP Internet name

  inspect the name DMZ smtp IP

  inspect the name ftp DMZ IP

  inspect the name DMZ tftp IP

  inspect the name DMZ udp IP

  inspect the name DMZ tcp IP

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 20

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key address x.x.180.133 xxxxxxxxxxx

  ISAKMP crypto keys xxxxxxxxxxx address 0.0.0.0 0.0.0.0

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac vpn test

  Crypto ipsec transform-set esp-3des esp-sha-hmac PIXRMT

  !

  dynamic-map crypto dny - Sai 25

  game of transformation-PIXRMT

  match static address PIX1

  !

  !

  static-card 10 map ipsec-isakmp crypto

  the value of x.x.180.133 peer

  the transform-set vpn-test value

  match static address of Hunt

  !

  map ISCMAP 15-isakmp ipsec crypto dynamic dny - isc

  !

  call the rsvp-sync

  !

  !

  !

  controller T1 0/0

  framing ESF

  linecode b8zs

  Slots 1-12 channels-group 0 64 speed

  Description controller to the remote frame relay

  !

  controller T1 0/1

  framing ESF

  linecode b8zs

  Timeslots 1-24 of channel-group 0 64 speed

  Description controller for internet link SBIS

  !

  interface Serial0/0:0

  Description CKT ID 14.HXGK.785129 Frame Relay to Remote Sites

  bandwidth 768

  no ip address

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  encapsulation frame-relay

  frame-relay lmi-type ansi

  !

  interface Serial0 / point to point 0:0.17

  Description Frame Relay to xxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 17 frame relay interface

  !

  interface Serial0 / point to point 0:0.18

  Description Frame Relay to xxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 18 frame relay interface

  !

  interface Serial0 / point to point 0:0.19

  Description Frame Relay to xxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 19 frame relay interface

  !

  interface Serial0 / point to point 0:0.20

  Description Frame Relay to xxxxxxxxxxxxx location

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 20 frame relay interface

  !

  interface Serial0 / point to point 0:0.21

  Description Frame Relay to xxxxxxxxxxxx

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 21 frame relay interface

  !

  interface Serial0 / point to point 0:0.101

  Description Frame Relay to xxxxxxxxxxx

  IP unnumbered Ethernet1/0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  No arp frame relay

  dlci 101 frame relay interface

  !

  interface Serial0/1:0

  CKT ID 14.HCGS.785383 T1 to ITT description

  bandwidth 1536

  IP address x.x.76.14 255.255.255.252

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  NAT outside IP

  inspect the Internet IP on

  no ip route cache

  card crypto ISCMAP

  !

  interface Ethernet1/0

  IP 10.1.1.1 255.255.0.0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  no ip route cache

  no ip mroute-cache

  Half duplex

  !

  interface Ethernet2/0

  IP 10.100.1.1 255.255.0.0

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP nat inside

  no ip route cache

  no ip mroute-cache

  Half duplex

  !

  router RIP

  10.0.0.0 network

  network 192.168.1.0

  !

  IP nat inside source list 112 interface Serial0/1: 0 overload

  IP nat inside source static tcp 10.1.3.4 443 209.184.71.138 443 extensible

  IP nat inside source static tcp 10.1.3.4 9869 209.184.71.138 9869 extensible

  IP nat inside source 10.1.3.2 static 209.184.71.140

  IP nat inside source static 10.1.3.6 209.184.71.139

  IP nat inside source static 10.1.3.8 209.184.71.136

  IP nat inside source static tcp 10.1.3.10 80 209.184.71.137 80 extensible

  IP classless

  IP route 0.0.0.0 0.0.0.0 x.x.76.13

  IP route 10.2.0.0 255.255.0.0 Serial0 / 0:0.19

  IP route 10.3.0.0 255.255.0.0 Serial0 / 0:0.18

  IP route 10.4.0.0 255.255.0.0 Serial0 / 0:0.17

  IP route 10.5.0.0 255.255.0.0 Serial0 / 0:0.20

  IP route 10.6.0.0 255.255.0.0 Serial0 / 0:0.21

  IP route 10.7.0.0 255.255.0.0 Serial0 / 0:0.101

  no ip address of the http server

  !

  !

  PIX1 static extended IP access list

  IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255

  IP access-list extended hunting-static

  IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255

  extended IP access vpn-static list

  ip permit 192.168.1.0 0.0.0.255 10.1.0.0 0.0.255.255

  IP 192.0.0.0 allow 0.255.255.255 10.1.0.0 0.0.255.255

  access-list 1 refuse 10.0.0.0 0.255.255.255

  access-list 1 permit one

  access-list 12 refuse 10.1.3.2

  access-list 12 allow 10.1.0.0 0.0.255.255

  access-list 12 allow 10.2.0.0 0.0.255.255

  access-list 12 allow 10.3.0.0 0.0.255.255

  access-list 12 allow 10.4.0.0 0.0.255.255

  access-list 12 allow 10.5.0.0 0.0.255.255

  access-list 12 allow 10.6.0.0 0.0.255.255

  access-list 12 allow 10.7.0.0 0.0.255.255

  access-list 112 deny ip host 10.1.3.2 everything

  access-list 112 refuse ip 10.1.0.0 0.0.255.255 192.168.1.0 0.0.0.255

  access-list 112 allow ip 10.1.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.2.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.3.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.4.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.5.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.6.0.0 0.0.255.255 everything

  access-list 112 allow ip 10.7.0.0 0.0.255.255 everything

  access-list 120 allow ip host 10.100.1.10 10.1.3.7

  not run cdp

  !

  Dial-peer cor custom

  !

  !

  !

  !

  connection of the banner ^ CCC

  ******************************************************************

  WARNING - Unauthorized USE strictly PROHIBITED!

  ******************************************************************

  ^ C

  !

  Line con 0

  line to 0

  password xxxxxxxxxxxx

  local connection

  Modem InOut

  StopBits 1

  FlowControl hardware

  line vty 0 4

  exec-timeout 15 0

  password xxxxxxxxxxxxxx

  opening of session

  !

  end

  Router #.

  Add the following to the PIX:

  > permitted connection ipsec sysopt

  This indicates the PIX around all ACLs for IPsec traffic. Now that your IPSec traffic is still subject to the standard rules of PIX, so launched inside the traffic is allowed to go in, but off-initiated traffic is not.

• Cisco PIX 501 to Cisco 3005 concentrator via remote access

  Hello people,

  I need your help.

  We got a Cisco PIX 501 in one place and this pix is configured for pppoe connection. The pix connects to internet via the pppoe client. an official ip address ping works well.

  So what I want to do is to establish a tunnel von between this pix and a cisco 3005 concentrator.

  But I failed to establish it.

  Here are the pix config. the acl? s are only for the test and will be replaced if it works.

  6.3 (4) version PIX

  interface ethernet0 10baset

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the password xxx

  passwd xxx

  hostname PIX - to THE

  domain araukraine.ua

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  outside ip access list allow a whole

  inside_access_in ip access list allow a whole

  pager lines 24

  opening of session

  Monitor logging warnings

  logging warnings put in buffered memory

  MTU outside 1456

  MTU inside 1456

  IP address outside pppoe setroute

  IP address inside 192.168.x.x 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  PDM location 192.168.x.x 255.255.255.224 inside

  forest warnings of PDM 500

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  outside access-group in external interface

  inside_access_in access to the interface inside group

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  the ssh LOCAL console AAA authentication

  Enable http server

  255.255.x.x 192.168.x.x http inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  255.255.x.x telnet inside 192.168.x.x

  Telnet timeout 5

  SSH 194.39.97.0 255.255.255.0 outside

  SSH timeout 5

  management-access inside

  Console timeout 0

  VPDN group pppoe_group request dialout pppoe

  VPDN group pppoe_group localname [email protected] / * /

  VPDN group ppp authentication pap pppoe_group

  VPDN username [email protected] / * / password *.

  encrypted privilege 15

  vpnclient Server 212.xx.xx.xx

  vpnclient mode network-extension-mode

  vpntest vpngroup vpnclient password *.

  vpnclient username pixtest password *.

  Terminal width 80

  the hub, I created a user pixtest, a group vpntest and I? ve created the rules of the network for example to what server, users behind the pix will be able to access.

  And that? s all.

  I couldn't send you exit pix or hub because I don't have an error or a message that the tunnel will be established.

  What can be wrong?

  Thanks for the replies

  This configuration example shows how to create an IPsec tunnel to a computer that is running the Client VPN Cisco's (4.x and later versions) to a Cisco VPN concentrator 3000 to allow the user to safely access the network inside the VPN concentrator.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a008026f96c.shtml

• VPN PPTP and PPPOE CLIENT ON PIX 501

  Hello

  Can I create a PPTP VPN and a client connection on a PIX 501 with a client to my ISP PPPOE connection. The PPPOE ip is dynamic and the VPN will be a static IP address. They gave me a username and password for VPN and PPPOE. Him also gave me an ip address for the VPN server.

  Should that happen, it's that the PPPOE should connect to the VPN to work.

  I can only get the PPPOE, but I don't know how to do this with a PPTP VPN set.

  Here is my config:
  
  PIX Version 6.3(3)
  
      interface ethernet0 auto
  
      interface ethernet1 100full
  
      nameif ethernet0 outside security0
  
      nameif ethernet1 inside security100
  
      enable password xxxxxxxx encrypted
  
      passwd xxxxxxx encrypted
  
      hostname neveroff
  
      domain-name neveroff.com
  
      fixup protocol dns maximum-length 512
  
      fixup protocol ftp 21
  
      fixup protocol h323 h225 1720
  
      fixup protocol h323 ras 1718-1719
  
      fixup protocol http 80
  
      fixup protocol rsh 514
  
      fixup protocol rtsp 554
  
      fixup protocol sip 5060
  
      fixup protocol sip udp 5060
  
      fixup protocol skinny 2000
  
      fixup protocol smtp 25
  
      fixup protocol sqlnet 1521
  
      fixup protocol tftp 69
  
      names
  
      access-list incoming permit icmp any any echo-reply
  
      access-list incoming permit icmp any any source-quench
  
      access-list incoming permit icmp any any unreachable
  
      access-list incoming permit icmp any any time-exceeded
  
      pager lines 24
  
      icmp permit any echo outside
  
      icmp permit any unreachable outside
  
      icmp permit any time-exceeded outside
  
      icmp permit any source-quench outside
  
      icmp permit any echo-reply outside
  
      icmp permit any information-reply outside
  
      icmp permit any mask-reply outside
  
      icmp permit any timestamp-reply outside
  
      mtu outside 1500
  
      mtu inside 1500
  
      ip address outside pppoe setroute
  
      ip address inside 192.168.1.1 255.255.255.0
  
      ip audit info action alarm
  
      ip audit attack action alarm
  
      pdm logging informational 100
  
      pdm history enable
  
      arp timeout 14400
  
      global (outside) 1 interface
  
      nat (inside) 1 192.168.1.0 255.255.255.0 0 0
  
      static (inside,outside) tcp interface smtp 192.168.1.201 smtp netmask 255.255.255.255 0 0
  
      access-group incoming in interface outside
  
      timeout xlate 0:05:00
  
      timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
  
      timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
  
      timeout uauth 0:05:00 absolute
  
      aaa-server TACACS+ protocol tacacs+
  
      aaa-server RADIUS protocol radius
  
      aaa-server LOCAL protocol local
  
      http server enable
  
      no snmp-server location
  
      no snmp-server contact
  
      snmp-server community public
  
      no snmp-server enable traps
  
      floodguard enable
  
      telnet timeout 5
  
      ssh 0.0.0.0 0.0.0.0 outside
  
      ssh 0.0.0.0 0.0.0.0 inside
  
      ssh timeout 5
  
      console timeout 0
  
      vpdn group pppoex request dialout pppoe
  
      vpdn group pppoex localname xxxxxxxxx
  
      vpdn group pppoex ppp authentication chap
  
      vpdn username xxxxxxxx password xxxxxxxx
  
      dhcpd address 192.168.1.10-192.168.1.41 inside
  
      dhcpd dns 192.168.1.1 168.210.2.2
  
      dhcpd lease 3600
  
      dhcpd ping_timeout 750
  
      dhcpd auto_config outside
  
      dhcpd enable inside
  
      username neveroff password TEnlGTQMwqamBzMn encrypted privilege 2
  
      terminal width 80
  
      Cryptochecksum:c5bfafa70f21ed55cc1b3df377e110bf
  
      : end
  
      

  Thank you

  Etienne

  Happy to help and please kindly mark the message as answered if you have not more than other questions. Thank you.