PIX 515 issuee remote VPN

Similar Questions

• PIX 7 - several remote VPN sessions to the same public IP address

  Hello

  Here's my problem:

  Employee A and employee B make VPN connections to the PIX even with their Cisco VPN clients. The two employees are behind the same NAT device, so have the same public IP address.

  As soon as the second employee initiates the VPN connection, the first employee is disconnected.

  I have a similar situation with a PIX 6.x version and it does not. Two employees can connect at the same time with the same credentials.

  Here is the configuration of remote access VPN I use:

  attributes of the strategy group gpolicy

  DHCP-scope network 10.X.X.X

  VPN - 5 concurrent connections

  Protocol-tunnel-VPN IPSec

  enable IPSec-udp

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list splitTunnelAcl

  the authentication of the user activation

  the firewall client no

  remoteuser password remotepass username

  remoteuser attributes username

  VPN-group-policy labtronix

  VPN - connections 2

  Protocol-tunnel-VPN IPSec

  value of group-lock vpngroup

  tunnel-group vpngroup type ipsec-ra

  tunnel-group vpngroup General attributes

  address ip_pool pool

  Group Policy - by default-gpolicy

  Any contribution is appreciated.

  Thank you.

  Most likely problem of nat - t

  Add "isakmp nat-traversal" in pix

• VPN to pix 515

  Good day to all,

  I'm trying to configure the client VPN to a PIX 515.  Once VPN'ed in, the traffic is going no where, but on THIS subnet. The Vlan that we are trying to achieve is a 10.111.250.x/23.  Once VPN'ed in the allocation of an IP address is 10.111.250.33 - 10.111.250.63. We can VPN in and get VPN IP assigned, but we cannot get anywhere inside VLANs.  I was sure that it could be done in a layer 2.  You can view the assigned addresses VPN arped entries and the inside address Vlan on the Pix.

  Keep in mind, my first thought was to change the VPN address assigned, but we do not want to carry on this Vlan especially because access is very limited.

  Is it possible to make this work?  If I have to redo attributes and policy, I.

  Thank you

  Dwane

  The output shows that the PIX is decrypt packets, but not encryption.

  So there is a good chance that packets are sent within the network but not to return.

  Check the following:

  management-access within the--> this command should allow ping to the IP of the VPN PIX inside (make sure you that if you can TEST this IP address when connected)

  Verify that the default gateway within the network (behind the PIX) is the current inside the property intellectual of the PIX.

  After these tests, post again "sh cry ips its"

  Federico.

• Cisco Pix 515 VPN problems

  Hi all

  Here's my problem, I have 2 PIX 515 firewall...

  I'm trying to implement a VPN site-to site between 2 of our websites...

  Two of these firewalls currently run another site to site VPN so I know who works...

  I can't do the second site to the site to launch the VPN... when looking on the syslogs I get refused packages...

  Protected networks are:

  172.16.48.0/24 and 172.16.4.0/22

  If I try to ping from the Cisco (172.16.48.4) to 172.16.4.5, I get the following syslog:

  2 sep 02 2008 08:59:47 106001 172.16.48.4 172.16.4.5 incoming TCP connection doesn't deny from 172.16.48.4/1231 to 172.16.4.5/135 SYN flags on the interface inside

  It seems that the tunnel is trying to initiate, but something is blocking the internal traffic to penetrate through the VPN.

  Don't know what that might be, the other VPN are working properly.

  Any help would be great...

  I enclose a copy of one of the configs...

  Let me know if you need another...

  no road inside 172.16.4.0 255.255.252.0 172.16.48.1 1

  Remove this path should you get. Please rate if it does. Similarly, if you have a road similar to the other end, it should be deleted as well.

• L2L pix 501 and remote access VPN

  Hi, I'm working on an old 501 PIX w / Software 6.3 (5), he already have access to remote VPN configuration and works very well, but now he needs a L2L implemented. One thing I try to do all the work remotely via VPN or ssh to the machine. I don't know what's on the other end, but they swear that it is set up and maybe my problem is when I start putting in orders for the other VPN it breaks the remote VPN access. One thing that I have to do is NAT a host on the inside to appear as another host on the end. I use these commands and I think it works cannot be said.

  access-list 101 permit ip remote_network 255.255.255.0 local_server host

  public static 10.1.0.203 (inside, outside) - access list 101

  then

  access-list 102 permit ip host 10.1.0.203 192.168.50.83
  access-list 102 permit ip host 10.1.0.203 192.168.50.86
  access-list 102 permit ip host 10.1.0.203 192.168.50.50
  access-list 102 permit ip host 10.1.0.203 192.168.50.85

  and use it to match against

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  EMDs-map 10 ipsec-isakmp crypto map
  correspondence address card crypto emds-map 10 102
  card crypto emds-map 10 peers set remote_vpn_server
  card crypto emds-card 10 set of transformation-ESP-3DES-SHA

  then

  ISAKMP key magic_key address remote_vpn_server netmask 255.255.255.255
  ISAKMP identity hostname
  part of pre authentication ISAKMP policy 10
  ISAKMP policy 10 3des encryption
  ISAKMP policy 10 sha hash
  10 1 ISAKMP policy group
  ISAKMP life duration strategy 10 86400

  and that is where it usually breaks the VPN, I don't know if the other VPN works due to not being not able to get to this server to try to ping, I don't really like to try this stuff remotely but I don't have a lot of choice at the moment.

  Any thoughts?

  Thank you

  Jarrid Graham

  Yes, just use the number of different sequence with 1 name of the crypto map. Please also ensure that your dynamic crypto map, which is your vpn client has the sequence down the crypto map (more), because you want to make sure that the static crypto map (for lan-to-lan tunnel has higher sequence number (lower number)).

  The political isakmp sequence number does not match, it is processed from top to bottom (number less than the high number) and also long 1 set of isakmp policy corresponds to the remote peer, it will be negotiated properly.

  Hope that answers your question and please note useful post. Thank you.

• termination of VPN client 4.0 on pix 515

  I am trying to connect the cisco 4.0 vpn client to a worm of pix 515 6.1 and receive as a result of errors that I guess are the related hashing algorithm but am not sure. Only DES is not enabled 3DES. Config output Cisco post interprets but apparently no error in config.

  Journal of VPN client:

  Cisco Systems VPN Client Version 4.0 (Rel)

  Copyright (C) 1998-2003 Cisco Systems, Inc. All rights reserved.

  Customer type: Windows, Windows NT

  Running: 5.0.2195

  1 10:58:34.890 25/09/03 Sev = Info/4 CM / 0 x 63100002

  Start the login process

  2 10:58:34.906 25/09/03 Sev = Info/4 CVPND/0xE3400001

  Microsoft's IPSec Policy Agent service stopped successfully

  3 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100004

  Establish a connection using Ethernet

  4 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100024

  Attempt to connect with the server "x.x.x.226".

  5 10:58:35.953 25/09/03 Sev = Info/6 IKE/0x6300003B

  Attempts to establish a connection with x.x.x.226.

  6 10:58:36.000 25/09/03 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Nat - T), VID (Frag), VID (Unity)) at x.x.x.226

  7 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700008

  IPSec driver started successfully

  8 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  9 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  10 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

  11 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  12 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

  13 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  14 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

  15 10:58:56.093 25/09/03 Sev = Info/4 IKE / 0 x 63000017

  Marking of IKE SA delete (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  16 10:58:56.593 25/09/03 Sev = Info/4 IKE/0x6300004A

  IKE negotiation to throw HIS (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  17 10:58:56.593 25/09/03 Sev = Info/4 CM / 0 x 63100014

  Could not establish the Phase 1 SA with the server 'x.x.x.226' due to the 'DEL_REASON_PEER_NOT_RESPONDING '.

  18 10:58:56.593 25/09/03 Sev = Info/5 CM / 0 x 63100025

  Initializing CVPNDrv

  19 10:58:56.593 25/09/03 Sev = Info/4 IKE / 0 x 63000001

  Signal received IKE to complete the VPN connection

  20 10:58:56.625 25/09/03 Sev = critique/1 CVPND/0xE3400001

  Service Microsoft's IPSec Policy Agent started successfully

  21 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  22 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  23 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  24 10:58:57.093 25/09/03 Sev = Info/4 IPSEC/0x6370000A

  IPSec driver successfully stopped

  Journal of Pix:

  crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

  Peer VPN: ISAKMP: approved new addition: ip:x.x.x.194 Total VPN peer: 1

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 1 Total VPN EEP

  RS: 1

  Exchange OAK_AG

  ISAKMP (0): treatment ITS payload. Message ID = 0

  ISAKMP (0): audit ISAKMP transform 1 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform against the policy of priority 1 2

  ISAKMP: encryption... What? 7?

  ISAKMP: MD5 hash

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 3 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 4 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: MD5 hash

  ISAKMP: default group 2

  ISAKMP: preshared auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 5 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 6 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: MD5 hash

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 7 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 8 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: MD5 hash

  ISAKMP: default group 2

  ISAKMP: preshared auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 9 against the policy of priority 1

  ISAKMP: 3DES-CBC encryption

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4

  crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP

  RS: 1

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP

  RS: 1

  crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP

  RS: 1

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP

  RS: 1

  ISAKMP (0): retransmission of phase 1...

  ISAKMP (0): retransmission of phase 1...

  ISAKMP (0): delete SA: src x.x.x.194 dst x.x.x.226

  ISADB: Reaper checking HIS 0x80db91c8, id_conn = 0 DELETE IT!

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 0 Total of VPN EEP

  RS: 1

  Peer VPN: ISAKMP: deleted peer: ip:x.x.x.194 VPN peer Total: 0

  ISAKMP: Remove the peer node for x.x.x.194

  Thanks for any help

  Hello

  Pix isakmp policy should have DES, MD5, and group 2 for the 4.x to connect Cisco VPN client, these are proposals that the client sends to the server...

  http://www.Cisco.com/univercd/CC/TD/doc/product/VPN/client/rel4_0/admin_gd/vcach6.htm#1157757

  This link will show you IKE proposals be configured on the PIX (VPN server)

  Arthur

• VPN for PIX 515 allowing access to a single host

  I have already setup on my PIX 515 a VPN connection, which allows the user to connect to our network via a cisco VPN client to access network resources.

  I want to configure now is an another VPN connection that external users can use but would only allow access to a host.

  E.g. I would like to VPN in my site but would be allowed to access the 10.1.1.1 on my network.

  How can I do this? What I have to install VPNGROUP another and somehow an access list to allow only traffic to a host of configuration. Can anyone help with the correct syntax for the PIX.

  Thank you

  Scott

  You will now have a bunch of commands "vpngroup" in your PIX, simply go into config mode and add more commands 'vpngroup' but with a different groupname. The VPN client then uses this group name to connect to the PIX.

  Another way to allow only access to a host for this PIX is to split tunnelling on this group, as well as in the tunnel of split ACL set only as a host.

• Accounting customer VPN on PIX 515 worm problem. 6.3

  Hello everyone! Is it possible to configure PIX 515 worm. 6.3 to send logs to the RADIUS to break when a VPN Client user loggs in and outside loggs? I can't find any aaa accounting command which allows this.

  Hello

  Accounting of VPN was added in PIX 7.x. It is not available with 6.x

  Kind regards

  Vivek

• Upgrade from PIX 515

  Hi all

  My company needs upgrade its PIX 515 to have the function VPN 3DES for remote site connection. So I just need to buy a license of 3DES for the PIX functionality? and can I also upgrade the IOS 6.1 so that I can use PDM to config the PIX? And I also need to upgrade the memory in the PIX?

  Thank you very much!

  Best regards

  Teru Lei

  Yes to the first question.

  Better 6.2 and pdm 2.1 I think.

  How much memory do you have? Reach

  http://www.Cisco.com/en/us/customer/products/sw/secursw/ps2120/prod_release_note09186a00800b1138.html#xtocid4

  There is memory for pix 6.2 requirements

  Good luck!

  --

  Alexis Fidalgo

  Systems engineer

  AT & T Argentina

• Site2Site and remote VPN

  I have a site2site between PIX506 and 877 router VPN. Site A has PIX506 and Site B router a in 877. I configured site2site VPN and it worked fine. I also configured remote VPN on PIX 506 so that the remote user can access A site. But when I configure remote VPN on PIX506 site2site VPN works and both sides can ping each other. But site B users cannot access any resource network or application of the SiteA while site A can access resources of site B. After removing remote VPN site configuration B can access the resources of the Site I joined the configuration of the two sites. Someone help me please site2site and remote VPN work at the same time.

  Please forgive me for not reading every line.

  an add-on quick about the pix configuration:

  change "isakmp key * address 213.181.169.8 netmask 255.255.255.255" at "isakmp key * address 213.181.169.8 netmask 255.255.255.255 No.-xauth No. config-mode.

• Cannot ping via remote VPN

  Hi all

  I have a client who uses a 506e with the cleint 4.02 for the remote VPN Cisco. The pix is multiple inside roads. The first network inside is 192.168.1.X and E1 of the 506 is 192.168.1.1. The second network is 10.71.56.X.

  The problem is as soon as the VPN is connected I can ping any host on the 192.168.1.X, but not anything on the 10.71.56.X network. Without netbios or the other. From the PIX, I can ping hosts on two internal networks.

  Here is the config below. Thank you!

  6.2 (2) version PIX

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  activate the password xxxxx

  passwd xxxxxxx

  hostname GNB - PIX

  cisco.com-domain name

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  names of

  QUBEADMIN tcp service object-group

  Beach of port-object 444 444

  outside_access_in list access permit tcp any host 12.X.X.X eq pop3

  outside_access_in list access permit tcp any host 12.X.X.X eq smtp

  outside_access_in list access permit tcp any host 12.X.X.X EQ field

  outside_access_in list access permit tcp any host 12.X.X.X eq www

  outside_access_in list access permit tcp any host 12.X.X.X QUBEADMIN object-group

  outside_access_in list access permit icmp any any echo response

  access-list outside_access_in allow icmp all once exceed

  outside_access_in list access permit tcp any host 12.169.2.21 eq ssh

  GNB_splitTunnelAcl ip 10.71.56.0 access list allow 255.255.255.0 any

  outside_cryptomap_dyn_20 ip access list allow any 10.71.56.32 255.255.255.224

  pager lines 24

  opening of session

  timestamp of the record

  logging paused

  logging buffered stored notifications

  Logging trap errors

  notifications to the history of logging

  the logging queue 0

  host of logging inside the 10.71.55.10

  logging out of the 192.104.109.91 host

  interface ethernet0 car

  Auto interface ethernet1

  ICMP allow any inside

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside 12.X.X.X 255.255.254.0

  IP address inside 192.168.1.254 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  local IP VPNPOOL 10.71.56.40 pool - 10.71.56.50

  history of PDM activate

  ARP timeout 14400

  Global interface 10 (external)

  NAT (inside) 0-list of access inside_outbound_nat0_acl

  NAT (inside) 10 0.0.0.0 0.0.0.0 0 0

  public static 12.X.X.X (Interior, exterior) 192.168.1.1 mask subnet 255.255.255.255 0 0

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 12.X.X.X 1

  Route inside 10.71.55.0 255.255.255.0 192.168.1.1 1

  Route inside 10.71.56.0 255.255.255.0 192.168.1.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  the ssh LOCAL console AAA authentication

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Dynamic crypto map outside_dyn_map 20 match address outside_cryptomap_dyn_20

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  ISAKMP allows outside

  part of pre authentication ISAKMP policy 20

  ISAKMP policy 20 3des encryption

  ISAKMP policy 20 chopping sha

  20 2 ISAKMP policy group

  ISAKMP duration strategy of life 20 86400

  vpngroup address VPNPOOL pool GUARD

  vpngroup dns-server 10.71.56.10 GNB 10.71.56.10

  GNB GNB_splitTunnelAcl vpngroup split tunnel

  vpngroup GNB 1800 idle time

  GNB vpngroup password *.

  Telnet timeout 5

  SSH timeout 60

  Terminal width 80

  Cryptochecksum:XXXXX

  : end

  [OK]

  GNB - PIX #.

  You use 10.71.56.0 255.255.255.0 in two places

  you route to it via 192.168.1.1, but you're also allocation of addresses for vpn clients. Guests who are on the segment 10.71.56.0/24, if they manage to get the connected vpn client package (which is assigned a 10.71.56.x) address, would not send the response packet to this request on the local subnet, the router that has the 192.168.1.1 interface, which is what would be needed to make it work.

  You must use a different network for your vpn clients block - you cannot use the same ip through two different networks space.

• PIX - 515 does not identify Tokenring Interfacecard

  Hello

  I installed a PIX-1 TR interface in the PIX 515. Start ok, 'answer' no configuration. SH LVE and sho int etc. presents only the build Ethernet0 and Eth1 but no interface tokenring.

  HS release looks like as follows.

  Thanks Ruedi

  pixfirewall # sh ver

  Cisco PIX Firewall Version 6.2 (2)

  Cisco PIX Device Manager Version 2.0 (2)

  Updated Saturday, June 7 02 17:49 by Manu

  pixfirewall until 10 mins dry 14

  Material: PIX - 515, 32 MB RAM, Pentium 200 MHz processor

  I28F640J5 @ 0 x 300 Flash, 16 MB

  BIOS Flash AT29C257 @ 0xfffd8000, 32 KB

  0: ethernet0: the address is 0003.6bf6.a8a9, irq 11

  1: ethernet1: the address is 0003.6bf6.a8aa, irq 10

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES: disabled

  Maximum Interfaces: 3

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: unlimited

  Throughput: unlimited

  Peer IKE: unlimited

  Serial number: 405341167 (0x182903ef)

  Activation key running: xxxxxxxxx

  Modified configuration of enable_15 to 13:11:47.490 UTC Tuesday, December 23, 2003

  pixfirewall #.

  Hello

  Token-Ring is no longer supported, I think since version 6.0.

• Try to connect to a remote VPN server

  This task was bleeding in my eyes. I can't make it work. I understand the principle of TCP-OUT ACCORD - IN but can't seem to reconcile it kind includes the firewall.

  Long and short of the situation:

  Company a static IP address assigned by the local society of DSL

  All computers inside network enjoy outdoor internet access and interconnectivity

  Remote VPN host has static IP

  Configuration VPN of a properly established and the remote control accounts are active.

  Does not connect when good ID and PASSWORD are entered.

  Anyone tried this before. Please assume that I have the skill level of a child of 5 years and the patience of the same thing.

  Thank you for your help.

  Timothy S. Murray

  A child under 5 huh? looks like a lot of people that I care. I'm kidding anyone, not me flame.

  In any case, we need a little more information here to go, it's a connection to a PIX PPTP you talk, or a router? Or is it IPSec (you mentioned GRE, that's why I think you speak of free WILL). Is the user authentication is done locally on the endpoint VPN device, or is it a server Radius/GANYMEDE involved?

  Can you send in the configuration of the end device, ensuring xxxxx valid IP addresses and passwords?

• PIX 515 adding a second DMZ

  Hello

  This is the specification of our PIX:

  Cisco PIX Firewall Version 6.2 (2)

  Cisco PIX Device Manager Version 2.0 (2)

  Updated Saturday, June 7 02 17:49 by Manu

  Firewall of the hours - days.

  Material: PIX - 515, 32 MB RAM, Pentium 200 MHz processor

  I28F640J5 @ 0 x 300 Flash, 16 MB

  BIOS Flash AT29C257 @ 0xfffd8000, 32 KB

  0: ethernet0: the address is 0003.6bf6.74a2, irq 11

  1: ethernet1: the address is 0003.6bf6.74a3, irq 10

  2: ethernet2: the address is 00a0.c944.395b, irq 9

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES: enabled

  Maximum Interfaces: 3

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: unlimited

  Throughput: unlimited

  Peer IKE: unlimited

  Is it possible to add a second DMZ simply by adding another network card to the system? If this is not the case, what I have to do to get a second DMZ?

  Kind regards

  Alan

  You have already 3 interfaces, and your license only allows 3 (that you run limited license). Read the line of your worm above show: maximum Interfaces: 3

  You must update your Unrestricted license, then you can have up to 6 interfaces.

  It will be useful.

  Steve

• The remote VPN Clients and Internet access

  I apologize in advance if this question has already been addressed. I am currently using a PIX Firewall Version 6.1 520 (2) running. I have several remote users that VPN for the PIX. Once the VPN tunnel is started, they are more able to connect to internet from their local computers. Is there a configuation on the PIX that allows remote users to have access to the internet when you are connected to the PIX.

  TIA,

  Jeff Gulick

  The Pix does not allow traffic enter and exit on the same interface. Therefore, a VPN user cannot access the Internet through the tunnel. If you use the Cisco client, enable tunneling split so that all traffic through the tunnel.

  If you use PPTP, you can turn off the option that makes the remote network, the default gateway. However, local routes should be added to these clients when they connect.

  Or you can use an additional interface on the firewall. One that puts an end to VPN tunnels and another providing for Internet connectivity. In this way the traffic is not enter/leave on the same interface.

  Of course, it is preferable if the customer Internet traffic does not go through the tunnel. It wastes your bandwidth and has security problems as well. I suggest you use the client to Cisco and the split tunneling.