Accounting customer VPN on PIX 515 worm problem. 6.3
Hello everyone! Is it possible to configure PIX 515 worm. 6.3 to send logs to the RADIUS to break when a VPN Client user loggs in and outside loggs? I can't find any aaa accounting command which allows this.
Hello
Accounting of VPN was added in PIX 7.x. It is not available with 6.x
Kind regards
Vivek
Tags: Cisco Security
Similar Questions
-
Hello
We have some difficulty in moving traffic in and out of a Cisco PIx 515 firewall. We use it with two demilitarized. The first DMZ has a mail in her Server (before end mail server) that communicates with a different mail server (back end mail server) inside, it is called DMZ1. The second DMZ (DMZ2) has some users who are expected to pass through the firewall to the outside and use the internet and must have access to the e-mail DMZ1 server. Inside users must be able to use the Internet and can access DMZ1. Here's the important part of our Setup.
What we were doing, we can correctly access from inside, inside users to access internet permit to join the DMZ1 e-mail server and the mail in DMZ1 server the inside. Our problem is that we are unable to browse the internet on the DMZ1 Messaging server if we put DMZ1 as gateway ip address on that server and the address ip of the DNS of the ISP is propely located on the same machine. Also, we could not do DMZ2 users browse the internet, although we allowed the www Protocol in the fromOut access list. One last question, can we do the DMZ2 a DHCP server on the interface on the PIX and do distribute ip addresses to users on that subnet only? Thanks for any help in advance.
6.3 (3) version PIX
interface ethernet0 car
Auto interface ethernet1
Auto interface ethernet2
Auto ethernet3 interface
!
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
nameif ethernet2 dmz1 security50
nameif ethernet3 dmz2 security40
!
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
!
names of
!
IP outside X.Y.Z.163 255.255.255.248
IP address inside 192.168.0.9 255.255.255.0
dmz1 192.168.10.1 IP address 255.255.255.0
IP address dmz2 192.168.20.1 255.255.255.0
!
fromOut list of access permit icmp any host X.Y.Z.162 source-quench
fromOut list of access permit icmp any host X.Y.Z.162 echo-reply
fromOut list of access permit icmp any unreachable host X.Y.Z.162
fromOut list of access permit icmp any host X.Y.Z.162 time limit
fromOut list access permit tcp any host X.Y.Z.162 EQ field
fromOut list access permit tcp any host X.Y.Z.162 eq telnet
fromOut list access permit tcp any host X.Y.Z.162 eq smtp
fromOut list access permit tcp any host X.Y.Z.162 eq www
!
fromDMZ1 list of access permit tcp host 192.168.10.2 192.168.0.0 255.255.255.0
fromDMZ1 list of allowed access host ip 192.168.10.2 192.168.0.0 255.255.255.0
!
fromDMZ2 list of access allowed tcp 192.168.20.0 255.255.255.0 192.168.10.0 255.255.255.0
!
pager lines 24
!
Outside 1500 MTU
Within 1500 MTU
dmz1 MTU 1500
dmz2 MTU 1500
!
Global (outside) 1 X.Y.Z.164 netmask 255.255.255.248
Global (outside) 2 X.Y.Z.165 netmask 255.255.255.248
NAT (inside) 1 192.168.0.0 255.255.255.0 0 0
NAT (dmz1) 1 192.168.10.2 255.255.255.255 0 0
NAT (dmz2) 2 192.168.20.0 255.255.255.0 0 0
static (inside, dmz1) 192.168.0.0 192.168.0.0 netmask 255.255.255.0 0 0
static (dmz2, dmz1) 192.168.0.0 192.168.0.0 netmask 255.255.255.0 0 0
static (dmz1, external) X.Y.Z.162 192.168.10.2 netmask 255.255.255.255 0 0
!
Access-group fromOut in interface outside
Access-group fromDMZ1 in interface dmz1
Access-group fromDMZ2 in the dmz2 interface
Route outside 0.0.0.0 0.0.0.0 X.Y.Z.161 1
Hi jamil,.
There is a sentence on the URL I sent you, you can now activate dhcp option within the interface. Just check this...
REDA
-
Good day to all,
I'm trying to configure the client VPN to a PIX 515. Once VPN'ed in, the traffic is going no where, but on THIS subnet. The Vlan that we are trying to achieve is a 10.111.250.x/23. Once VPN'ed in the allocation of an IP address is 10.111.250.33 - 10.111.250.63. We can VPN in and get VPN IP assigned, but we cannot get anywhere inside VLANs. I was sure that it could be done in a layer 2. You can view the assigned addresses VPN arped entries and the inside address Vlan on the Pix.
Keep in mind, my first thought was to change the VPN address assigned, but we do not want to carry on this Vlan especially because access is very limited.
Is it possible to make this work? If I have to redo attributes and policy, I.
Thank you
Dwane
The output shows that the PIX is decrypt packets, but not encryption.
So there is a good chance that packets are sent within the network but not to return.
Check the following:
management-access within the--> this command should allow ping to the IP of the VPN PIX inside (make sure you that if you can TEST this IP address when connected)
Verify that the default gateway within the network (behind the PIX) is the current inside the property intellectual of the PIX.
After these tests, post again "sh cry ips its"
Federico.
-
VPN for PIX 515 allowing access to a single host
I have already setup on my PIX 515 a VPN connection, which allows the user to connect to our network via a cisco VPN client to access network resources.
I want to configure now is an another VPN connection that external users can use but would only allow access to a host.
E.g. I would like to VPN in my site but would be allowed to access the 10.1.1.1 on my network.
How can I do this? What I have to install VPNGROUP another and somehow an access list to allow only traffic to a host of configuration. Can anyone help with the correct syntax for the PIX.
Thank you
Scott
You will now have a bunch of commands "vpngroup" in your PIX, simply go into config mode and add more commands 'vpngroup' but with a different groupname. The VPN client then uses this group name to connect to the PIX.
Another way to allow only access to a host for this PIX is to split tunnelling on this group, as well as in the tunnel of split ACL set only as a host.
-
Hello forum, I have a question please answer if someone knows the answer...
Here is my scenario:
Central location Pix515 (192.168.0.0/24)
Location 1: (192.168.1.0/24)
Situation 2: (192.168.2.0/24)
Location 3: (192.168.3.0/24) local pool for vpn clients
192.168.0.0/24, 192.168.1.0/24 lan - LAN IPSEC
192.168.0.0/24 for 192.168.2.0/24 lan - lan IPSEC
192.168.0.0/24 to 192.168.3.0/24 ezvpn IPSEC
Question:
Is it posible to connect Location1 and Location2 via Pix, or Location1 and Location3?
On encryption ACLs on each location of traffic destined to another location is included for the encryption process.
for example, location1 acl:
Access 100 per 192.168.1.0 255.255.255.0 192.168.0.0 255.255.255.0
Access 100 per 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
Access 100 per 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
other locations have a similar LCD-s
There is no problem to access locations 192.168.0.0/24, but traffic between sites does not work.
I think that pix encrypt packets outside ariving.
I know, it's possible on IOS with IPSEC over GRE tunnels with some routing, but PIX?
Republic of Korea
Hi Rok-
Allows traffic between VPN sites does not currently work with Pix OS 6.3.4 and earlier. Code pix 7.0, which will be published later this year, will enable traffic between the same interfaces of VPN security level. This will allow talked to talk communication. I have configured the week last with Pix 7.0 beta code, so I know this is a new feature and it will work.
IOS does not have this limitation with IPSec. The GRE is not required to IOS to make communication speaks to talk work, although it can be used.
I hope this helps you understand what is happening.
Please let us know this that followed by questions that you have.
Thank you!
Peter
PS., pls remember to note the positions so others will know if we have provided you with the information you need!
-
Can the customer vpn to pix interface unprotected to a protected interface
I have a pix multi-interface, the description of the interface is as follows:
Outside-> 10MB to ISP
Inside-> vlan main
DMZ-> Web servers, etc...
Lab1-> test application servers
LAB2-> test application servers
etc...
Comments wireless-> free wireless (connected to the Cisco WAP)
The open wireless only has access to the internet, not one of the reliable networks. It is an untrusted interface (security lvl 1). The external interface is security 0.
I want to be able to allow vpn access from the wireless in networks of trust like vpn from outside (internet) is processed.
I guess that the pix sees a vpn connection attempt to another of its interfaces.
The client times out connecting since the wireless for the pix outside IP interface.
The pix records simply this:
January 20, 2009 13:38:23: % 7-710005-PIX: UDP request and eliminated from 192.168.20.5/1346 to GuestWireless:yy.yy.yy.yy/500
the external interface IP = yy.yy.yy.yy
the pix is also the dhcp server for wireless network connections.
Is it still possible? If so, what Miss me?
Thank you
Dave
To answer: -.
The leg wireless of the PIX is the security level 1, and the external interface is the security level 0. That would not mean that vpn is launched from a higher to a lower security interface? Yes but the traffic is clear--asked to terminate a VPN connection to an interface that is locally attached to the PIX effectivly in the inside of the unit. Sure that PIX will refuse the connection he received on the external interface of the interface without comment thread.
No it isn't the same thing, something like: -.
crypto ISAKMP enable GuestWireless - this indicates the PIX to listen and accept connections VPN ISAKMP/issues of ANY device connected to this interface FOR the GuestWireless interface.
HTH >
-
Cisco ASA 5510 VPN with PIX 515
Hello
I have VPN between Cisco ASA and Cisco PIX.
I saw in my syslog server this error that appears once a day, more or less:
Received a package encrypted with any HIS correspondent, drop
I ve seen issue in another post, but in none of then the solution.
Here are my files from the firewall configuration:
Output from the command: 'show running-config '.
: Saved
:
ASA Version 8.2 (1)
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto WAN_map2 2 corresponds to the address WAN_cryptomap_1
card crypto WAN_map2 2 set pfs
card crypto WAN_map2 2 peer 62.80.XX game. XX
map WAN_map2 2 game of transformation-ESP-DES-MD5 crypto
card crypto WAN_map2 2 defined security-association 2700 seconds life
card crypto WAN_map2 2 set nat-t-disable
card crypto WAN_map2 WAN interface
enable LAN crypto ISAKMP
ISAKMP crypto enable WAN
crypto ISAKMP policy 1
preshared authentication
the Encryption
md5 hash
Group 5
lifetime 28800
No encryption isakmp nat-traversal
tunnel-group 62.80.XX. XX type ipsec-l2l
tunnel-group 62.80.XX. IPSec-attributes of XX
pre-shared-key *.++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
8.0 (4) version PIX
!
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card encryption VPN_map2 3 corresponds to the address VPN_cryptomap_2
card encryption VPN_map2 3 set pfs
card crypto VPN_map2 3 peer 194.30.XX game. XX
VPN_map2 3 transform-set ESP-DES-MD5 crypto card game
card encryption VPN_map2 3 defined security-association life seconds 2700
card encryption VPN_map2 3 set security-association kilobytes of life 4608000
card VPN_map2 3 set nat-t-disable encryption
VPN crypto map VPN_map2 interface
crypto ISAKMP enable VPN
crypto ISAKMP allow inside
crypto ISAKMP policy 30
preshared authentication
the Encryption
md5 hash
Group 5
lifetime 28800
No encryption isakmp nat-traversal
ISAKMP crypto am - disable
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec
tunnel-group 194.30.XX. XX type ipsec-l2l
tunnel-group 194.30.XX. IPSec-attributes of XX
pre-shared-key *.If you need more information dedailed ask me questions.
Thanks in advance for your help.
Javi
Hi Javi,
Please after the release of "see broadcasting DfltGrpPolicy of any political group." See if you have the "vpn-idle-timoeout" command configured in that. If so, please change to "vpn-idle-timeout no" and see if that stops at these popping up error messages.
http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/uz.html#wp1571426
Thank you and best regards,
Assia
-
I set up PPTP VPN on PIX 515 access with unrestricted license for Windows-based computers. I can connect but I'm unable to access all the resources on the network. I suspect this has something to access the list, but I don't know where to start. Here's the relevant part of the PIX config:
access-list all-traffic ip to allow a whole
access-list 100 permit icmp any any echo response
access-list 100 permit icmp any one time exceed
access-list 100 permit everything all unreachable icmp
.
IP address outside x.x.x.130 255.255.255.252
IP address inside 192.168.254.1 255.255.255.0
IP address x.x.x.97 255.255.255.224 DMZ1
address IP DMZ2 192.168.251.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP local pool vpnpool 192.168.254.201 - 192.168.254.254
.
Global (outside) 1 x.x.x.65 - x.x.x.93 netmask 255.255.255.224
Global (outside) 1 x.x.x.94 netmask 255.255.255.224
NAT (inside) 1 access-list all-traffic 0 0
(DMZ1) 1 access-list all-traffic NAT 0 0
Access-group 100 in external interface
Route outside 0.0.0.0 0.0.0.0 x.x.x.129 1
.
Sysopt connection permit-pptp
Telnet 192.168.254.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0
VPDN Group 1 accept dialin pptp
PAP VPDN Group 1 ppp authentication
VPDN Group 1 chap for ppp authentication
VPDN Group 1 ppp authentication mschap
VPDN group ppp 1 encryption mppe auto
VPDN Group 1 client configuration address local vpnpool
VPDN Group 1 pptp echo 60
VPDN Group 1 client authentication local
VPDN username * password *.
VPDN allow outside
dhcpd address 192.168.254.100 - 192.168.254.200 inside
dhcpd dns x.x.x.131 x.x.x.200
dhcpd rental 86400
dhcpd ping_timeout 750
dhcpd allow inside
Looks like you forgot to add a "nat 0" defines that there are no PAT beween your local inside network and the PPTP DHCP pool.
PPTP pool must be different from the inside pool otherwise it is not routable correctly.
no ip local pool vpnpool 192.168.254.201 - 192.168.254.254
# Choose a new network PPTP pool that is not in use
example of dansMon # is 192.168.1.0/24
IP local pool vpnpool 192.168.1.1 - 192.168.1.254
access-list 101 permit ip 192.168.254.0 255.255.255.0 192.168.1.0 255.255.255.0
(Inside) NAT 0-list of access 101
See this site for more information:
http://www.Cisco.com/pcgi-bin/support/browse/psp_view.pl?p=hardware:PIX & s = Software_Configuration
see PPTP
sincerely
Patrick
-
Hi all
Here's my problem, I have 2 PIX 515 firewall...
I'm trying to implement a VPN site-to site between 2 of our websites...
Two of these firewalls currently run another site to site VPN so I know who works...
I can't do the second site to the site to launch the VPN... when looking on the syslogs I get refused packages...
Protected networks are:
172.16.48.0/24 and 172.16.4.0/22
If I try to ping from the Cisco (172.16.48.4) to 172.16.4.5, I get the following syslog:
2 sep 02 2008 08:59:47 106001 172.16.48.4 172.16.4.5 incoming TCP connection doesn't deny from 172.16.48.4/1231 to 172.16.4.5/135 SYN flags on the interface inside
It seems that the tunnel is trying to initiate, but something is blocking the internal traffic to penetrate through the VPN.
Don't know what that might be, the other VPN are working properly.
Any help would be great...
I enclose a copy of one of the configs...
Let me know if you need another...
no road inside 172.16.4.0 255.255.252.0 172.16.48.1 1
Remove this path should you get. Please rate if it does. Similarly, if you have a road similar to the other end, it should be deleted as well.
-
termination of VPN client 4.0 on pix 515
I am trying to connect the cisco 4.0 vpn client to a worm of pix 515 6.1 and receive as a result of errors that I guess are the related hashing algorithm but am not sure. Only DES is not enabled 3DES. Config output Cisco post interprets but apparently no error in config.
Journal of VPN client:
Cisco Systems VPN Client Version 4.0 (Rel)
Copyright (C) 1998-2003 Cisco Systems, Inc. All rights reserved.
Customer type: Windows, Windows NT
Running: 5.0.2195
1 10:58:34.890 25/09/03 Sev = Info/4 CM / 0 x 63100002
Start the login process
2 10:58:34.906 25/09/03 Sev = Info/4 CVPND/0xE3400001
Microsoft's IPSec Policy Agent service stopped successfully
3 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100004
Establish a connection using Ethernet
4 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100024
Attempt to connect with the server "x.x.x.226".
5 10:58:35.953 25/09/03 Sev = Info/6 IKE/0x6300003B
Attempts to establish a connection with x.x.x.226.
6 10:58:36.000 25/09/03 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Nat - T), VID (Frag), VID (Unity)) at x.x.x.226
7 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700008
IPSec driver started successfully
8 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
9 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021
Retransmit the last package!
10 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226
11 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021
Retransmit the last package!
12 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226
13 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021
Retransmit the last package!
14 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226
15 10:58:56.093 25/09/03 Sev = Info/4 IKE / 0 x 63000017
Marking of IKE SA delete (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING
16 10:58:56.593 25/09/03 Sev = Info/4 IKE/0x6300004A
IKE negotiation to throw HIS (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING
17 10:58:56.593 25/09/03 Sev = Info/4 CM / 0 x 63100014
Could not establish the Phase 1 SA with the server 'x.x.x.226' due to the 'DEL_REASON_PEER_NOT_RESPONDING '.
18 10:58:56.593 25/09/03 Sev = Info/5 CM / 0 x 63100025
Initializing CVPNDrv
19 10:58:56.593 25/09/03 Sev = Info/4 IKE / 0 x 63000001
Signal received IKE to complete the VPN connection
20 10:58:56.625 25/09/03 Sev = critique/1 CVPND/0xE3400001
Service Microsoft's IPSec Policy Agent started successfully
21 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
22 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
23 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
24 10:58:57.093 25/09/03 Sev = Info/4 IPSEC/0x6370000A
IPSec driver successfully stopped
Journal of Pix:
crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226
Peer VPN: ISAKMP: approved new addition: ip:x.x.x.194 Total VPN peer: 1
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 1 Total VPN EEP
RS: 1
Exchange OAK_AG
ISAKMP (0): treatment ITS payload. Message ID = 0
ISAKMP (0): audit ISAKMP transform 1 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform against the policy of priority 1 2
ISAKMP: encryption... What? 7?
ISAKMP: MD5 hash
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 3 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 4 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: MD5 hash
ISAKMP: default group 2
ISAKMP: preshared auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 5 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 6 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: MD5 hash
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 7 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 8 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: MD5 hash
ISAKMP: default group 2
ISAKMP: preshared auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 9 against the policy of priority 1
ISAKMP: 3DES-CBC encryption
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4
crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP
RS: 1
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP
RS: 1
crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP
RS: 1
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP
RS: 1
ISAKMP (0): retransmission of phase 1...
ISAKMP (0): retransmission of phase 1...
ISAKMP (0): delete SA: src x.x.x.194 dst x.x.x.226
ISADB: Reaper checking HIS 0x80db91c8, id_conn = 0 DELETE IT!
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 0 Total of VPN EEP
RS: 1
Peer VPN: ISAKMP: deleted peer: ip:x.x.x.194 VPN peer Total: 0
ISAKMP: Remove the peer node for x.x.x.194
Thanks for any help
Hello
Pix isakmp policy should have DES, MD5, and group 2 for the 4.x to connect Cisco VPN client, these are proposals that the client sends to the server...
http://www.Cisco.com/univercd/CC/TD/doc/product/VPN/client/rel4_0/admin_gd/vcach6.htm#1157757
This link will show you IKE proposals be configured on the PIX (VPN server)
Arthur
-
is eazy customer vpn is supported only on the routers of the 800 pix 7.0 series iOS
I'm eazy vpn with pix 7.0.4 ios with a 3640 router. the 3640 router is like aeazy vpn client. and the pix as the eazy vpn server. the client connect and continues to ask the xauth parameter. I read in the release notes that requires this vpn eay 12.2 and especially sure ios for 806 routers. the pix also does support eaxy customer vpn routers fo 800 series only. urgent help required. If this true pix sucks big time. they force us to buy routers.they become like microsoft. pls help
Assane
According to this document
http://www.Cisco.com/en/us/products/sw/secursw/ps5299/index.html
Cisco Easy VPN remote is now available on Cisco 800, 1700, 1800, 2800, 3800 and series UBR900 routers, Cisco PIX 501 security equipment and 506th and Cisco VPN 3002 hardware Clients.
So no support to 3640...
M.
Hope that helps if it is
-
Login problem VPN on PIX on the side of the inside of the n/w
I am tring to connect to the vpn server (pix) outside my laptop within the network.
I have routed ip vpn on pix515 and fine ping pix.but not able to ping of 3550 switch and computer laptop.
How to get the vpn ip Switch? as I don't know the mask of the ip...
I would also like to know... is their something extra that I need on pix or 3550?
Hello!
-What is the default gateway of your laptop?
-You do any kind of NAT on the PIX? What is NAT PAT, static or normal?
-Can you ping the inside of the PIX of the laptop?
There could be several problems to solve here.
(1) first of all, make sure that your laptop has access to the internet
(2) If you want to ping him make sure internet you have an ACL on the PIX like the one below:
i.e.
Allow Access - list icmp an entire TEST
TEST group access in the interface outside
Also make sure you have no access list applied inside the PIX
-Now, can you connect at all?
-When you connect to? Another PIX? Router? Hub?
If you pass by PAT make sure that you have this command on the PIX:
"fixup protocol esp-ike.
Please let me know if you can answer my questions, in this way, it would be easier to help you.
Frank
-
Translation problem group on PIX 515
Hi can someone help me with this?
I'm trying to configure a PIX 515 to pass messages icmp from the interface vlan dmz configured on interface (Vlan 3) PIX inside interface.
setting it up like this
interface ethernet0 100full
interface ethernet1 100full
interface ethernet2 100full
physical interface ethernet2 vlan2
logical interface ethernet2 vlan3
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
nameif ethernet2 msx interieure4
nameif dmz security7 vlan3
SH nat
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
NAT (dmz) 1 0.0.0.0 0.0.0.0 0 0
NAT (msx) 1 0.0.0.0 0.0.0.0 0 0
Global HS
Global (inside) 1 interface
Global interface (dmz) 1
Global (msx) 1 interface
At this stage I am not concerened with access lists that I get the error message is as follows
155:-echo request ICMP dmz:192.168.3.1 to 10.240.2.2 ID = 512 seq = 11520 length = 40
305005: no translation not found for icmp src dmz:192.168.3.1 dst domestic group: 10.240.2.2 (type 8, code 0)
I'm not an expert when it comes to the PIX can someone help. Two other things can help shed light on the problem, there is no configuration of routing between Vlan interfaces, this could be a problem? I tried a static command and still have the same error that the order was... static (dmz, inside) 192.168.3.1 192.168.3.1
Hi David:
As you try to allow host from an interface for low security to a high security interface, you must have
static (high, low) high high
In this case, you must:
static (inside, dmz) 10.240.2.2 10.240.2.2 netmask 255.255.255.255 0 0
I assume that you already have an access list to allow the icmp message of echo applied to the DMZ interface. If it is not already there, just add an ACE to allow the icmp message to echo that you should be good to go.
Sincerely,
Binh
-
Save the password on the Client VPN with PIX
I'm running a PIX 515 6.1 (2) configured for a small number of VPN clients. I want VPN clients to automatically remember the password of login for users do not have to enter it each time (we have an application which periodically autoconnexions).
While it is a configurable option with concentrators 3000 series, it seems not be configurable with the PIX.
The only work around, I can find is to make the connection file (.pcf) read-only and set SaveUserPassword = 1. The problem
which is the password, and then must be stored in clear text in the file and it becomes inconvenient for the user to change their password.
Does anyone know if the command exists on the PIX from the VPN client to save the connection password?
Thank you
Misha
The command to do this is not currently available on the PIX. He has just been included in the IOS EZVPN server functionality, but have not heard of anything anyone yet as to if it will be included in the PIX.
If you want this feature, do not hesitate to contact your account manager and have them grow for him, the more customers requesting a new feature faster he gets.
-
PDM with PIX 515 does not work
I just upgraded our PIX 515 of 6.1 to 6.2. I also added support FOR and loaded the version 2.1 of the PDM. I am trying to browse the MDP, but I can't. What Miss me?
Hello
have you added the following lines to your config file and have you used HTTPS to access the pix (http is not taken in charge, only https)?
Enable http server
http A.B.C.D 255.255.255.255 inside
A.B.C.D is the ip address of the host from which you are trying to reach the pix with the pdm.
If you're still having problems after the addition of these two lines, you might have a look at this page:
http://www.Cisco.com/warp/customer/110/pdm_http404.shtml
Kind regards
Tom
Maybe you are looking for
-
Due to an overheating problem, I reinstalled Windows XP. The Device manager now showes no port COM and the toshiba software modem give an error message when I try to use it. Please help;
-
My wife just bought a MacBook Air. Does need an anti-virus or needs a security suite?
-
IBM Wireless USB Enhanced keyboard and mouse model SK-8812
This keyboard has a set of access keys that I find very useful I have recently converted from Windows XP to Windows 7, and this function no longer works. + Anyone know if I can get a keyboard for Windows 7 driver?
-
KB2419632 security update will not install XP SP3... no error code, only statement "have not installed" in a dialog box. Any tips?
-
How can I apply a gradient to a stroke of the art/pattern/dispersion? (CC 2015)
If I try STROKE becomes black, even if I have tints colorization method