VPN to pix 515
Good day to all,
I'm trying to configure the client VPN to a PIX 515. Once VPN'ed in, the traffic is going no where, but on THIS subnet. The Vlan that we are trying to achieve is a 10.111.250.x/23. Once VPN'ed in the allocation of an IP address is 10.111.250.33 - 10.111.250.63. We can VPN in and get VPN IP assigned, but we cannot get anywhere inside VLANs. I was sure that it could be done in a layer 2. You can view the assigned addresses VPN arped entries and the inside address Vlan on the Pix.
Keep in mind, my first thought was to change the VPN address assigned, but we do not want to carry on this Vlan especially because access is very limited.
Is it possible to make this work? If I have to redo attributes and policy, I.
Thank you
Dwane
The output shows that the PIX is decrypt packets, but not encryption.
So there is a good chance that packets are sent within the network but not to return.
Check the following:
management-access within the--> this command should allow ping to the IP of the VPN PIX inside (make sure you that if you can TEST this IP address when connected)
Verify that the default gateway within the network (behind the PIX) is the current inside the property intellectual of the PIX.
After these tests, post again "sh cry ips its"
Federico.
Tags: Cisco Security
Similar Questions
-
VPN for PIX 515 allowing access to a single host
I have already setup on my PIX 515 a VPN connection, which allows the user to connect to our network via a cisco VPN client to access network resources.
I want to configure now is an another VPN connection that external users can use but would only allow access to a host.
E.g. I would like to VPN in my site but would be allowed to access the 10.1.1.1 on my network.
How can I do this? What I have to install VPNGROUP another and somehow an access list to allow only traffic to a host of configuration. Can anyone help with the correct syntax for the PIX.
Thank you
Scott
You will now have a bunch of commands "vpngroup" in your PIX, simply go into config mode and add more commands 'vpngroup' but with a different groupname. The VPN client then uses this group name to connect to the PIX.
Another way to allow only access to a host for this PIX is to split tunnelling on this group, as well as in the tunnel of split ACL set only as a host.
-
Accounting customer VPN on PIX 515 worm problem. 6.3
Hello everyone! Is it possible to configure PIX 515 worm. 6.3 to send logs to the RADIUS to break when a VPN Client user loggs in and outside loggs? I can't find any aaa accounting command which allows this.
Hello
Accounting of VPN was added in PIX 7.x. It is not available with 6.x
Kind regards
Vivek
-
Hello forum, I have a question please answer if someone knows the answer...
Here is my scenario:
Central location Pix515 (192.168.0.0/24)
Location 1: (192.168.1.0/24)
Situation 2: (192.168.2.0/24)
Location 3: (192.168.3.0/24) local pool for vpn clients
192.168.0.0/24, 192.168.1.0/24 lan - LAN IPSEC
192.168.0.0/24 for 192.168.2.0/24 lan - lan IPSEC
192.168.0.0/24 to 192.168.3.0/24 ezvpn IPSEC
Question:
Is it posible to connect Location1 and Location2 via Pix, or Location1 and Location3?
On encryption ACLs on each location of traffic destined to another location is included for the encryption process.
for example, location1 acl:
Access 100 per 192.168.1.0 255.255.255.0 192.168.0.0 255.255.255.0
Access 100 per 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
Access 100 per 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
other locations have a similar LCD-s
There is no problem to access locations 192.168.0.0/24, but traffic between sites does not work.
I think that pix encrypt packets outside ariving.
I know, it's possible on IOS with IPSEC over GRE tunnels with some routing, but PIX?
Republic of Korea
Hi Rok-
Allows traffic between VPN sites does not currently work with Pix OS 6.3.4 and earlier. Code pix 7.0, which will be published later this year, will enable traffic between the same interfaces of VPN security level. This will allow talked to talk communication. I have configured the week last with Pix 7.0 beta code, so I know this is a new feature and it will work.
IOS does not have this limitation with IPSec. The GRE is not required to IOS to make communication speaks to talk work, although it can be used.
I hope this helps you understand what is happening.
Please let us know this that followed by questions that you have.
Thank you!
Peter
PS., pls remember to note the positions so others will know if we have provided you with the information you need!
-
Cisco ASA 5510 VPN with PIX 515
Hello
I have VPN between Cisco ASA and Cisco PIX.
I saw in my syslog server this error that appears once a day, more or less:
Received a package encrypted with any HIS correspondent, drop
I ve seen issue in another post, but in none of then the solution.
Here are my files from the firewall configuration:
Output from the command: 'show running-config '.
: Saved
:
ASA Version 8.2 (1)
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto WAN_map2 2 corresponds to the address WAN_cryptomap_1
card crypto WAN_map2 2 set pfs
card crypto WAN_map2 2 peer 62.80.XX game. XX
map WAN_map2 2 game of transformation-ESP-DES-MD5 crypto
card crypto WAN_map2 2 defined security-association 2700 seconds life
card crypto WAN_map2 2 set nat-t-disable
card crypto WAN_map2 WAN interface
enable LAN crypto ISAKMP
ISAKMP crypto enable WAN
crypto ISAKMP policy 1
preshared authentication
the Encryption
md5 hash
Group 5
lifetime 28800
No encryption isakmp nat-traversal
tunnel-group 62.80.XX. XX type ipsec-l2l
tunnel-group 62.80.XX. IPSec-attributes of XX
pre-shared-key *.++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
8.0 (4) version PIX
!
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card encryption VPN_map2 3 corresponds to the address VPN_cryptomap_2
card encryption VPN_map2 3 set pfs
card crypto VPN_map2 3 peer 194.30.XX game. XX
VPN_map2 3 transform-set ESP-DES-MD5 crypto card game
card encryption VPN_map2 3 defined security-association life seconds 2700
card encryption VPN_map2 3 set security-association kilobytes of life 4608000
card VPN_map2 3 set nat-t-disable encryption
VPN crypto map VPN_map2 interface
crypto ISAKMP enable VPN
crypto ISAKMP allow inside
crypto ISAKMP policy 30
preshared authentication
the Encryption
md5 hash
Group 5
lifetime 28800
No encryption isakmp nat-traversal
ISAKMP crypto am - disable
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec
tunnel-group 194.30.XX. XX type ipsec-l2l
tunnel-group 194.30.XX. IPSec-attributes of XX
pre-shared-key *.If you need more information dedailed ask me questions.
Thanks in advance for your help.
Javi
Hi Javi,
Please after the release of "see broadcasting DfltGrpPolicy of any political group." See if you have the "vpn-idle-timoeout" command configured in that. If so, please change to "vpn-idle-timeout no" and see if that stops at these popping up error messages.
http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/uz.html#wp1571426
Thank you and best regards,
Assia
-
VPN to PIX access problem.
I set up PPTP VPN on PIX 515 access with unrestricted license for Windows-based computers. I can connect but I'm unable to access all the resources on the network. I suspect this has something to access the list, but I don't know where to start. Here's the relevant part of the PIX config:
access-list all-traffic ip to allow a whole
access-list 100 permit icmp any any echo response
access-list 100 permit icmp any one time exceed
access-list 100 permit everything all unreachable icmp
.
IP address outside x.x.x.130 255.255.255.252
IP address inside 192.168.254.1 255.255.255.0
IP address x.x.x.97 255.255.255.224 DMZ1
address IP DMZ2 192.168.251.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP local pool vpnpool 192.168.254.201 - 192.168.254.254
.
Global (outside) 1 x.x.x.65 - x.x.x.93 netmask 255.255.255.224
Global (outside) 1 x.x.x.94 netmask 255.255.255.224
NAT (inside) 1 access-list all-traffic 0 0
(DMZ1) 1 access-list all-traffic NAT 0 0
Access-group 100 in external interface
Route outside 0.0.0.0 0.0.0.0 x.x.x.129 1
.
Sysopt connection permit-pptp
Telnet 192.168.254.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0
VPDN Group 1 accept dialin pptp
PAP VPDN Group 1 ppp authentication
VPDN Group 1 chap for ppp authentication
VPDN Group 1 ppp authentication mschap
VPDN group ppp 1 encryption mppe auto
VPDN Group 1 client configuration address local vpnpool
VPDN Group 1 pptp echo 60
VPDN Group 1 client authentication local
VPDN username * password *.
VPDN allow outside
dhcpd address 192.168.254.100 - 192.168.254.200 inside
dhcpd dns x.x.x.131 x.x.x.200
dhcpd rental 86400
dhcpd ping_timeout 750
dhcpd allow inside
Looks like you forgot to add a "nat 0" defines that there are no PAT beween your local inside network and the PPTP DHCP pool.
PPTP pool must be different from the inside pool otherwise it is not routable correctly.
no ip local pool vpnpool 192.168.254.201 - 192.168.254.254
# Choose a new network PPTP pool that is not in use
example of dansMon # is 192.168.1.0/24
IP local pool vpnpool 192.168.1.1 - 192.168.1.254
access-list 101 permit ip 192.168.254.0 255.255.255.0 192.168.1.0 255.255.255.0
(Inside) NAT 0-list of access 101
See this site for more information:
http://www.Cisco.com/pcgi-bin/support/browse/psp_view.pl?p=hardware:PIX & s = Software_Configuration
see PPTP
sincerely
Patrick
-
Hi all
Here's my problem, I have 2 PIX 515 firewall...
I'm trying to implement a VPN site-to site between 2 of our websites...
Two of these firewalls currently run another site to site VPN so I know who works...
I can't do the second site to the site to launch the VPN... when looking on the syslogs I get refused packages...
Protected networks are:
172.16.48.0/24 and 172.16.4.0/22
If I try to ping from the Cisco (172.16.48.4) to 172.16.4.5, I get the following syslog:
2 sep 02 2008 08:59:47 106001 172.16.48.4 172.16.4.5 incoming TCP connection doesn't deny from 172.16.48.4/1231 to 172.16.4.5/135 SYN flags on the interface inside
It seems that the tunnel is trying to initiate, but something is blocking the internal traffic to penetrate through the VPN.
Don't know what that might be, the other VPN are working properly.
Any help would be great...
I enclose a copy of one of the configs...
Let me know if you need another...
no road inside 172.16.4.0 255.255.252.0 172.16.48.1 1
Remove this path should you get. Please rate if it does. Similarly, if you have a road similar to the other end, it should be deleted as well.
-
termination of VPN client 4.0 on pix 515
I am trying to connect the cisco 4.0 vpn client to a worm of pix 515 6.1 and receive as a result of errors that I guess are the related hashing algorithm but am not sure. Only DES is not enabled 3DES. Config output Cisco post interprets but apparently no error in config.
Journal of VPN client:
Cisco Systems VPN Client Version 4.0 (Rel)
Copyright (C) 1998-2003 Cisco Systems, Inc. All rights reserved.
Customer type: Windows, Windows NT
Running: 5.0.2195
1 10:58:34.890 25/09/03 Sev = Info/4 CM / 0 x 63100002
Start the login process
2 10:58:34.906 25/09/03 Sev = Info/4 CVPND/0xE3400001
Microsoft's IPSec Policy Agent service stopped successfully
3 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100004
Establish a connection using Ethernet
4 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100024
Attempt to connect with the server "x.x.x.226".
5 10:58:35.953 25/09/03 Sev = Info/6 IKE/0x6300003B
Attempts to establish a connection with x.x.x.226.
6 10:58:36.000 25/09/03 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Nat - T), VID (Frag), VID (Unity)) at x.x.x.226
7 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700008
IPSec driver started successfully
8 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
9 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021
Retransmit the last package!
10 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226
11 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021
Retransmit the last package!
12 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226
13 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021
Retransmit the last package!
14 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226
15 10:58:56.093 25/09/03 Sev = Info/4 IKE / 0 x 63000017
Marking of IKE SA delete (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING
16 10:58:56.593 25/09/03 Sev = Info/4 IKE/0x6300004A
IKE negotiation to throw HIS (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING
17 10:58:56.593 25/09/03 Sev = Info/4 CM / 0 x 63100014
Could not establish the Phase 1 SA with the server 'x.x.x.226' due to the 'DEL_REASON_PEER_NOT_RESPONDING '.
18 10:58:56.593 25/09/03 Sev = Info/5 CM / 0 x 63100025
Initializing CVPNDrv
19 10:58:56.593 25/09/03 Sev = Info/4 IKE / 0 x 63000001
Signal received IKE to complete the VPN connection
20 10:58:56.625 25/09/03 Sev = critique/1 CVPND/0xE3400001
Service Microsoft's IPSec Policy Agent started successfully
21 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
22 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
23 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
24 10:58:57.093 25/09/03 Sev = Info/4 IPSEC/0x6370000A
IPSec driver successfully stopped
Journal of Pix:
crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226
Peer VPN: ISAKMP: approved new addition: ip:x.x.x.194 Total VPN peer: 1
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 1 Total VPN EEP
RS: 1
Exchange OAK_AG
ISAKMP (0): treatment ITS payload. Message ID = 0
ISAKMP (0): audit ISAKMP transform 1 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform against the policy of priority 1 2
ISAKMP: encryption... What? 7?
ISAKMP: MD5 hash
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 3 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 4 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: MD5 hash
ISAKMP: default group 2
ISAKMP: preshared auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 5 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 6 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: MD5 hash
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 7 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 8 against the policy of priority 1
ISAKMP: encryption... What? 7?
ISAKMP: MD5 hash
ISAKMP: default group 2
ISAKMP: preshared auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
ISAKMP: attribute 3584
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): audit ISAKMP transform 9 against the policy of priority 1
ISAKMP: 3DES-CBC encryption
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared extended auth
ISAKMP: type of life in seconds
ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4
crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP
RS: 1
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP
RS: 1
crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP
RS: 1
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP
RS: 1
ISAKMP (0): retransmission of phase 1...
ISAKMP (0): retransmission of phase 1...
ISAKMP (0): delete SA: src x.x.x.194 dst x.x.x.226
ISADB: Reaper checking HIS 0x80db91c8, id_conn = 0 DELETE IT!
Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 0 Total of VPN EEP
RS: 1
Peer VPN: ISAKMP: deleted peer: ip:x.x.x.194 VPN peer Total: 0
ISAKMP: Remove the peer node for x.x.x.194
Thanks for any help
Hello
Pix isakmp policy should have DES, MD5, and group 2 for the 4.x to connect Cisco VPN client, these are proposals that the client sends to the server...
http://www.Cisco.com/univercd/CC/TD/doc/product/VPN/client/rel4_0/admin_gd/vcach6.htm#1157757
This link will show you IKE proposals be configured on the PIX (VPN server)
Arthur
-
PIX - 515 does not identify Tokenring Interfacecard
Hello
I installed a PIX-1 TR interface in the PIX 515. Start ok, 'answer' no configuration. SH LVE and sho int etc. presents only the build Ethernet0 and Eth1 but no interface tokenring.
HS release looks like as follows.
Thanks Ruedi
pixfirewall # sh ver
Cisco PIX Firewall Version 6.2 (2)
Cisco PIX Device Manager Version 2.0 (2)
Updated Saturday, June 7 02 17:49 by Manu
pixfirewall until 10 mins dry 14
Material: PIX - 515, 32 MB RAM, Pentium 200 MHz processor
I28F640J5 @ 0 x 300 Flash, 16 MB
BIOS Flash AT29C257 @ 0xfffd8000, 32 KB
0: ethernet0: the address is 0003.6bf6.a8a9, irq 11
1: ethernet1: the address is 0003.6bf6.a8aa, irq 10
Features licensed:
Failover: disabled
VPN - A: enabled
VPN-3DES: disabled
Maximum Interfaces: 3
Cut - through Proxy: enabled
Guardians: enabled
URL filtering: enabled
Internal hosts: unlimited
Throughput: unlimited
Peer IKE: unlimited
Serial number: 405341167 (0x182903ef)
Activation key running: xxxxxxxxx
Modified configuration of enable_15 to 13:11:47.490 UTC Tuesday, December 23, 2003
pixfirewall #.
Hello
Token-Ring is no longer supported, I think since version 6.0.
-
Hi all
My company needs upgrade its PIX 515 to have the function VPN 3DES for remote site connection. So I just need to buy a license of 3DES for the PIX functionality? and can I also upgrade the IOS 6.1 so that I can use PDM to config the PIX? And I also need to upgrade the memory in the PIX?
Thank you very much!
Best regards
Teru Lei
Yes to the first question.
Better 6.2 and pdm 2.1 I think.
How much memory do you have? Reach
There is memory for pix 6.2 requirements
Good luck!
--
Alexis Fidalgo
Systems engineer
AT & T Argentina
-
VPN to PIX, Win2K, Active Directory - where to start?
Hello world.
I am waiting the arrival of a PIX 515 and 501 for firewalls and creating VPN between my main site and a remote location. Remoteness is having a LAN installed but will not have a real Win2k domian while the main site is an area complete with exchange and AD win2k. The two site will connect to INet w / cable modems.
Here's the question:
Is it possible to have this remote site to be part of my site main area via the VPN? Can I set up a server on the remote site to replicate AD to, in which case the VPN is stopped for some reason any. Do I need to open ports on the firewall or not because it will be on a VPN?
Is it an easy thing to do? Is a beginner at the top of his head?
Thanks in advance for any advice.
Marc
No router required - basically, everything will be static routed - your customers, regardless of the site, will have the pix as the default gateway. each pix will have a default gateway configured, by you, by a statement of 'road '. Each pix ACL crypto will also act as a static route through the tunnel to the other pix
-
Save the password on the Client VPN with PIX
I'm running a PIX 515 6.1 (2) configured for a small number of VPN clients. I want VPN clients to automatically remember the password of login for users do not have to enter it each time (we have an application which periodically autoconnexions).
While it is a configurable option with concentrators 3000 series, it seems not be configurable with the PIX.
The only work around, I can find is to make the connection file (.pcf) read-only and set SaveUserPassword = 1. The problem
which is the password, and then must be stored in clear text in the file and it becomes inconvenient for the user to change their password.
Does anyone know if the command exists on the PIX from the VPN client to save the connection password?
Thank you
Misha
The command to do this is not currently available on the PIX. He has just been included in the IOS EZVPN server functionality, but have not heard of anything anyone yet as to if it will be included in the PIX.
If you want this feature, do not hesitate to contact your account manager and have them grow for him, the more customers requesting a new feature faster he gets.
-
Hello
This is the specification of our PIX:
Cisco PIX Firewall Version 6.2 (2)
Cisco PIX Device Manager Version 2.0 (2)
Updated Saturday, June 7 02 17:49 by Manu
Firewall of the hours - days.
Material: PIX - 515, 32 MB RAM, Pentium 200 MHz processor
I28F640J5 @ 0 x 300 Flash, 16 MB
BIOS Flash AT29C257 @ 0xfffd8000, 32 KB
0: ethernet0: the address is 0003.6bf6.74a2, irq 11
1: ethernet1: the address is 0003.6bf6.74a3, irq 10
2: ethernet2: the address is 00a0.c944.395b, irq 9
Features licensed:
Failover: disabled
VPN - A: enabled
VPN-3DES: enabled
Maximum Interfaces: 3
Cut - through Proxy: enabled
Guardians: enabled
URL filtering: enabled
Internal hosts: unlimited
Throughput: unlimited
Peer IKE: unlimited
Is it possible to add a second DMZ simply by adding another network card to the system? If this is not the case, what I have to do to get a second DMZ?
Kind regards
Alan
You have already 3 interfaces, and your license only allows 3 (that you run limited license). Read the line of your worm above show: maximum Interfaces: 3
You must update your Unrestricted license, then you can have up to 6 interfaces.
It will be useful.
Steve
-
PDM with PIX 515 does not work
I just upgraded our PIX 515 of 6.1 to 6.2. I also added support FOR and loaded the version 2.1 of the PDM. I am trying to browse the MDP, but I can't. What Miss me?
Hello
have you added the following lines to your config file and have you used HTTPS to access the pix (http is not taken in charge, only https)?
Enable http server
http A.B.C.D 255.255.255.255 inside
A.B.C.D is the ip address of the host from which you are trying to reach the pix with the pdm.
If you're still having problems after the addition of these two lines, you might have a look at this page:
http://www.Cisco.com/warp/customer/110/pdm_http404.shtml
Kind regards
Tom
-
PIX 515 and software version 6.3 (4)
We have a PIX 515 (not 515E). Currently, we are running software version 6.2 (2). I was wondering if we can improve the software to version 6.3 (3) or 6.3 (4), or do we need to replace the hardware with PIX 515E?
Also what should I do on my current PDM version 2.0 (2) if it is possible to upgrade the PIX to a 6.3 version?
Thank you.
You can run on the Pix515 6.34. It takes at least 16 MB of flash and 32 MB of RAM.
If you use PDM, you will need to be updated also.
Josh
Maybe you are looking for
-
Questions of IOS 9.3.2
Some of my buddies told me to NOT UPDATE to the new 9.3.2 in my iPad 2 Air, there are some issues like battery draining, Wi - Fi issues, Bluetooth problems, activation, applications, installation, problems and random reboots. Some one has met such pr
-
Analog output DNL value details
I have an application where I use a card PCI-6221 to generate a sinusoidal signal over a wide range of amplitudes (> 1000: 1). Obviously at low amplitudes, the waveform becomes very pixelated, but the harmonics generated by it are not a problem in th
-
BlackBerry Smartphones do a security wipe and now cannot set up my email!
Hello I did a security wipe on my Blackberry Bold 9900. I managed to restore everything, however I can't seem to configure my email address (which is a Yahoo address). I get the error message that it has not been possible to connect to the server. I
-
Windows Update errors 80071 has 91 and 800F0922
Hi all I get the same exact errors after doing a system restore. Anyone has any ideas on solutions? I have already run this utility from Windows Update as well. Thank you. Separated from -. https://answers.Microsoft.com/en-us/Windows/Forum/windows_8-
-
Hi, I have two tables t01 and t02 both of them have the id column that the cluster column. But some same IDs have different rowid (data block address) why? What is a reason could explain you?Select a.id, b.id, a.rowid rowid01, b.rowid rowid02 t01, t0