PIX-515E-R-BUN MEM upgrade with PIX-515-MEM-32

Similar Questions

• PDM with PIX 515 does not work

  I just upgraded our PIX 515 of 6.1 to 6.2. I also added support FOR and loaded the version 2.1 of the PDM. I am trying to browse the MDP, but I can't. What Miss me?

  Hello

  have you added the following lines to your config file and have you used HTTPS to access the pix (http is not taken in charge, only https)?

  Enable http server

  http A.B.C.D 255.255.255.255 inside

  A.B.C.D is the ip address of the host from which you are trying to reach the pix with the pdm.

  If you're still having problems after the addition of these two lines, you might have a look at this page:

  http://www.Cisco.com/warp/customer/110/pdm_http404.shtml

  Kind regards

  Tom

• You want to upgrade to OS for my Mcair with mem 4 GB 10.7.5 running. Which that I had to upgrade with? Thank you, hhai65c

  You want to update OS for my Mcair 10.7.5 running 4 GB mem. What operating system should I upgrade with? Thank you, hhai65c

  More details about exactly what MBA you have would be useful?

• Upgrade from PIX 515

  Hi all

  My company needs upgrade its PIX 515 to have the function VPN 3DES for remote site connection. So I just need to buy a license of 3DES for the PIX functionality? and can I also upgrade the IOS 6.1 so that I can use PDM to config the PIX? And I also need to upgrade the memory in the PIX?

  Thank you very much!

  Best regards

  Teru Lei

  Yes to the first question.

  Better 6.2 and pdm 2.1 I think.

  How much memory do you have? Reach

  http://www.Cisco.com/en/us/customer/products/sw/secursw/ps2120/prod_release_note09186a00800b1138.html#xtocid4

  There is memory for pix 6.2 requirements

  Good luck!

  --

  Alexis Fidalgo

  Systems engineer

  AT & T Argentina

• PIX 515 and software version 6.3 (4)

  We have a PIX 515 (not 515E). Currently, we are running software version 6.2 (2). I was wondering if we can improve the software to version 6.3 (3) or 6.3 (4), or do we need to replace the hardware with PIX 515E?

  Also what should I do on my current PDM version 2.0 (2) if it is possible to upgrade the PIX to a 6.3 version?

  Thank you.

  You can run on the Pix515 6.34. It takes at least 16 MB of flash and 32 MB of RAM.

  If you use PDM, you will need to be updated also.

  Josh

• PIX 515 limited software technical spec

  I couldn't find a complete tech

  specifications of the restricted part of the software on the PIX-515-R-DMZ-BUN, which is this chassis seem to bear no x interfaces, y amount of RAM and Z no users inside. X = 3, Y = 32 meg, which is Z and are there restrictions more and more of this?

  Rgds

  Martyn Beck

  The only chassis PIX that has limitations of the user is the 501 PIX which comes with a 10, 50 or unlimited user license. The 515 has not any restrictions on the number of internal users that this number is rather arbitrary. Instead, we use the throughput and simultaneous connections that are roughly 190 MB of throughput and 130 000 simultaneous connections. Also the license restricted on the 515 does not failover of any kind.

  Here is a link to 515E data sheets:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_data_sheet09186a0080091b15.html

  I hope this helps.

  Scott

• PIX 515 does not recognize the DIMM 128 MB

  PIX 515 does not recognize the DIMM 128 MB. Won't recognize only 32 MB. Also when the upgrade to 7.0, I get an error message that it has not enough flash, but I have 16 MB of flash needed.

  PIX 515 not recognizing 128 MB may be due to, in my opinion, pix-515 supports 64 MB. PIX-515e can support 128 MB. Now error Pix by reading not enough flash I got the same message when I tried to load 7.0 release using the tftp with padding interface configured to the local network with an attached TFTP server segment. I then tried the interruption during the startup control method, once the PIX reached ROMMON > issue 'auto of e1 interface', 'address 10.0.0.1', server 10.0.0.2, there are a few other commands. You may be familiar with them, otherwise use find under cisco.

  HTH

• Question of pix 515 2 ISP

  I have a client with a 515 cisco pix. Is it possible to have 2 separate configs on the pix and power quickly select what config you want to begin? My client had problems lately with his main ISPS who happens be the fastest connection between the 2 and when it comes down there do intellectual property changes on the pix to perform the failover manually.

  Ok..

  I have a client with a 515 cisco pix. Is it possible to have 2 separate configs on the pix and power quickly select what config you want to begin?

  -YES, YOU CAN CONFIGURE YOUR PIX 515E IN MULTIPLE CONTEXT

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808d2b63.shtml

  My client has had problems lately with its main ISP which is be the fastest connection between the 2 and when it breaks down there manually make changes to intellectual property on the pix to make the transition to the

  -YOU CAN CONFIGURE "FAI DOUBLE FEATURE."

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00806e880b.shtml

• PIX 515 6.1 (1) crashes every night

  We have a PIX 515 E Firewall (failover) with a simple configuration to allow web traffic only from inside. PIX with three interfaces ethernet and the DMZ is rarely used for specific needs. A www server is hosted with authentication through aaa for incoming users inside.

  For the last week, PIX crashes end each evening. No traffic doesn't cross the pix and we cannot ping all devices of pix as well. There are a lot of "no buffers" counts seen in all the PIX interfaces. The CPU usage is about 21%.

  Can anyone help to determine if this could be a hardware problem?

  Best regards, Murali

  Hi Murali,

  I'm not aware of any problem with the hardware, but there could be a software bug. I suggest that you open a case with cisco tac.

  or you can upgrade to 6.1.4 which has fix for most of the bugs.

  Thank you

  Syed

• PIX 515 DMZ problem

  Hello

  We have some difficulty in moving traffic in and out of a Cisco PIx 515 firewall. We use it with two demilitarized. The first DMZ has a mail in her Server (before end mail server) that communicates with a different mail server (back end mail server) inside, it is called DMZ1. The second DMZ (DMZ2) has some users who are expected to pass through the firewall to the outside and use the internet and must have access to the e-mail DMZ1 server. Inside users must be able to use the Internet and can access DMZ1. Here's the important part of our Setup.

  What we were doing, we can correctly access from inside, inside users to access internet permit to join the DMZ1 e-mail server and the mail in DMZ1 server the inside. Our problem is that we are unable to browse the internet on the DMZ1 Messaging server if we put DMZ1 as gateway ip address on that server and the address ip of the DNS of the ISP is propely located on the same machine. Also, we could not do DMZ2 users browse the internet, although we allowed the www Protocol in the fromOut access list. One last question, can we do the DMZ2 a DHCP server on the interface on the PIX and do distribute ip addresses to users on that subnet only? Thanks for any help in advance.

  6.3 (3) version PIX

  interface ethernet0 car

  Auto interface ethernet1

  Auto interface ethernet2

  Auto ethernet3 interface

  !

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  nameif ethernet2 dmz1 security50

  nameif ethernet3 dmz2 security40

  !

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  !

  names of

  !

  IP outside X.Y.Z.163 255.255.255.248

  IP address inside 192.168.0.9 255.255.255.0

  dmz1 192.168.10.1 IP address 255.255.255.0

  IP address dmz2 192.168.20.1 255.255.255.0

  !

  fromOut list of access permit icmp any host X.Y.Z.162 source-quench

  fromOut list of access permit icmp any host X.Y.Z.162 echo-reply

  fromOut list of access permit icmp any unreachable host X.Y.Z.162

  fromOut list of access permit icmp any host X.Y.Z.162 time limit

  fromOut list access permit tcp any host X.Y.Z.162 EQ field

  fromOut list access permit tcp any host X.Y.Z.162 eq telnet

  fromOut list access permit tcp any host X.Y.Z.162 eq smtp

  fromOut list access permit tcp any host X.Y.Z.162 eq www

  !

  fromDMZ1 list of access permit tcp host 192.168.10.2 192.168.0.0 255.255.255.0

  fromDMZ1 list of allowed access host ip 192.168.10.2 192.168.0.0 255.255.255.0

  !

  fromDMZ2 list of access allowed tcp 192.168.20.0 255.255.255.0 192.168.10.0 255.255.255.0

  !

  pager lines 24

  !

  Outside 1500 MTU

  Within 1500 MTU

  dmz1 MTU 1500

  dmz2 MTU 1500

  !

  Global (outside) 1 X.Y.Z.164 netmask 255.255.255.248

  Global (outside) 2 X.Y.Z.165 netmask 255.255.255.248

  NAT (inside) 1 192.168.0.0 255.255.255.0 0 0

  NAT (dmz1) 1 192.168.10.2 255.255.255.255 0 0

  NAT (dmz2) 2 192.168.20.0 255.255.255.0 0 0

  static (inside, dmz1) 192.168.0.0 192.168.0.0 netmask 255.255.255.0 0 0

  static (dmz2, dmz1) 192.168.0.0 192.168.0.0 netmask 255.255.255.0 0 0

  static (dmz1, external) X.Y.Z.162 192.168.10.2 netmask 255.255.255.255 0 0

  !

  Access-group fromOut in interface outside

  Access-group fromDMZ1 in interface dmz1

  Access-group fromDMZ2 in the dmz2 interface

  Route outside 0.0.0.0 0.0.0.0 X.Y.Z.161 1

  Hi jamil,.

  There is a sentence on the URL I sent you, you can now activate dhcp option within the interface. Just check this...

  REDA

• termination of VPN client 4.0 on pix 515

  I am trying to connect the cisco 4.0 vpn client to a worm of pix 515 6.1 and receive as a result of errors that I guess are the related hashing algorithm but am not sure. Only DES is not enabled 3DES. Config output Cisco post interprets but apparently no error in config.

  Journal of VPN client:

  Cisco Systems VPN Client Version 4.0 (Rel)

  Copyright (C) 1998-2003 Cisco Systems, Inc. All rights reserved.

  Customer type: Windows, Windows NT

  Running: 5.0.2195

  1 10:58:34.890 25/09/03 Sev = Info/4 CM / 0 x 63100002

  Start the login process

  2 10:58:34.906 25/09/03 Sev = Info/4 CVPND/0xE3400001

  Microsoft's IPSec Policy Agent service stopped successfully

  3 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100004

  Establish a connection using Ethernet

  4 10:58:34.906 25/09/03 Sev = Info/4 CM / 0 x 63100024

  Attempt to connect with the server "x.x.x.226".

  5 10:58:35.953 25/09/03 Sev = Info/6 IKE/0x6300003B

  Attempts to establish a connection with x.x.x.226.

  6 10:58:36.000 25/09/03 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Nat - T), VID (Frag), VID (Unity)) at x.x.x.226

  7 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700008

  IPSec driver started successfully

  8 10:58:36.000 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  9 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  10 10:58:41.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

  11 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  12 10:58:46.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

  13 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  14 10:58:51.093 25/09/03 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to x.x.x.226

  15 10:58:56.093 25/09/03 Sev = Info/4 IKE / 0 x 63000017

  Marking of IKE SA delete (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  16 10:58:56.593 25/09/03 Sev = Info/4 IKE/0x6300004A

  IKE negotiation to throw HIS (I_Cookie = 20FC277498A5D2DC R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  17 10:58:56.593 25/09/03 Sev = Info/4 CM / 0 x 63100014

  Could not establish the Phase 1 SA with the server 'x.x.x.226' due to the 'DEL_REASON_PEER_NOT_RESPONDING '.

  18 10:58:56.593 25/09/03 Sev = Info/5 CM / 0 x 63100025

  Initializing CVPNDrv

  19 10:58:56.593 25/09/03 Sev = Info/4 IKE / 0 x 63000001

  Signal received IKE to complete the VPN connection

  20 10:58:56.625 25/09/03 Sev = critique/1 CVPND/0xE3400001

  Service Microsoft's IPSec Policy Agent started successfully

  21 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  22 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  23 10:58:57.093 25/09/03 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  24 10:58:57.093 25/09/03 Sev = Info/4 IPSEC/0x6370000A

  IPSec driver successfully stopped

  Journal of Pix:

  crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

  Peer VPN: ISAKMP: approved new addition: ip:x.x.x.194 Total VPN peer: 1

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 1 Total VPN EEP

  RS: 1

  Exchange OAK_AG

  ISAKMP (0): treatment ITS payload. Message ID = 0

  ISAKMP (0): audit ISAKMP transform 1 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform against the policy of priority 1 2

  ISAKMP: encryption... What? 7?

  ISAKMP: MD5 hash

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 3 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 4 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: MD5 hash

  ISAKMP: default group 2

  ISAKMP: preshared auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 5 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 6 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: MD5 hash

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 7 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 8 against the policy of priority 1

  ISAKMP: encryption... What? 7?

  ISAKMP: MD5 hash

  ISAKMP: default group 2

  ISAKMP: preshared auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b

  ISAKMP: attribute 3584

  ISAKMP (0): atts are not acceptable. Next payload is 3

  ISAKMP (0): audit ISAKMP transform 9 against the policy of priority 1

  ISAKMP: 3DES-CBC encryption

  ISAKMP: hash SHA

  ISAKMP: default group 2

  ISAKMP: preshared extended auth

  ISAKMP: type of life in seconds

  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4

  crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP

  RS: 1

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP

  RS: 1

  crypto_isakmp_process_block: CBC x.x.x.194, dest x.x.x.226

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt is incremented to peers: 2 Total VPN EEP

  RS: 1

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 1 Total VPN EEP

  RS: 1

  ISAKMP (0): retransmission of phase 1...

  ISAKMP (0): retransmission of phase 1...

  ISAKMP (0): delete SA: src x.x.x.194 dst x.x.x.226

  ISADB: Reaper checking HIS 0x80db91c8, id_conn = 0 DELETE IT!

  Peer VPN: ISAKMP: ip:x.x.x.194 Ref cnt decremented to peers: 0 Total of VPN EEP

  RS: 1

  Peer VPN: ISAKMP: deleted peer: ip:x.x.x.194 VPN peer Total: 0

  ISAKMP: Remove the peer node for x.x.x.194

  Thanks for any help

  Hello

  Pix isakmp policy should have DES, MD5, and group 2 for the 4.x to connect Cisco VPN client, these are proposals that the client sends to the server...

  http://www.Cisco.com/univercd/CC/TD/doc/product/VPN/client/rel4_0/admin_gd/vcach6.htm#1157757

  This link will show you IKE proposals be configured on the PIX (VPN server)

  Arthur

• How to open a port and limit the range of addresses that use it on PIX 515?

  I have a Pix 515 v6.3 and a new piece of software that I'm getting soon need aura 5080 open port for incoming & outgoing HTTP traffic. The server will be in my DMZ to 10.0.0.1

  I would like to restrict inbound access to this port so that it can be used in 4 specific IP adderess foreign xxx.xxx.xxx.24 through xxx.xxx.xxx.27 and also, if possible, limit the outbound destination using this port to a single specific foreign IP address xxx.xxx.xxx.30.

  Could you please tell me the best way to do it.

  Thank you in advance for a relative novice to PIX.

  PIX (config) # access list acl-outside permit tcp host xxx.xxx.xxx.24 host MyWWWPublicIP eq 5080

  PIX (config) # access list acl-outside permit tcp host xxx.xxx.xxx.25 host MyWWWPublicIP eq 5080

  PIX (config) # access list acl-outside permit tcp host MyWWWPublicIP eq xxx.xxx.xxx.26 host 5080

  PIX (config) # access list acl-outside permit tcp host MyWWWPublicIP eq xxx.xxx.xxx.27 host 5080

  PIX (config) # access - group acl-outside in interface outside

  PIX (config) # access list acl - dmx permit tcp host 10.0.0.1 xxx.xxx.xxx.30 eq 5080

  PIX (config) # access - group acl - dmz dmz interface

  static (inside, outside) MyWWWPublicIP 10.0.0.1 netmask 255.255.255.255 0 0

  See also:

  PIX 500 series firewall

  http://www.Cisco.com/pcgi-bin/support/browse/psp_view.pl?p=hardware:PIX & s = Software_Configuration

  Configuration of the PIX Firewall with access to the Mail Server on the DMZ network

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a008015efa9.shtml

  sincerely

  Patrick

• A question about the old Pix 515

  Hi Experts.

  My client needs additional interfaces of FE and do not want to migrate the chassis 515E.

  Can the data sheet of the former 515 Pix no longer available due to the declaration of the EOS, you please confirm that the Pix 515 supports 1FE - PIX and PIX - 4FE cards before ordering one of them?

  Thank you

  The 515 supports 4 interface cards. Make sure they are running a UR pix license if - 515R takes only supported 3 interfaces.

• DNS traffic blocked after PAT - PIX 515

  I have PIX 515 with 3 named NIC (internal, external, dmz)

  I have 2 servers (Exchange and Windows 2000 with SMTP) in the demilitarized zone.

  I currently have a static command pointing to doamin for exchange Server IP address in the DMZ.

  I wanted to PAT on the IP address of the e-mail domain so that the configuration will look like as follows.

  The IP field will be used for the global IP

  all pop3 for global ip traffic will go to Exchange

  all www for the global IP traffic will go to Exchange

  all smtp for global ip traffic will go to the Windows 2000-based SMTP relay (SMTP relay is configured to send the e-mail received in exchange Server)

  I hosted DNS udp and tcp traffic to the servers.

  before pat, the server can use DNS to resolve IP domain e-mail and send mail to the Internet.

  As soon as I PAT the Internet e-mail delivery stops.

  When I did an NSLOOKUP command returns an error indicating that the DNS server cannot be resloved.

  The servere DNS used by these 2 servers are servers DNS of ISP.

  Is there any concern when you PAT.

  Thank you

  Hello

  I found the problem:

  for now, your dmz servers can go to the internet with pop3, smtp, and www. Only for these protocols is a (static) translation to provide in the config file.

  You will need to will provide you a translation for other protocols (for example, dns) also. This can be accomplished with one of the following two things:

  create a nat - pair overall for the DMZ for outdoor

  NAT (dmz) 1 0.0.0.0 0.0.0.0

  Global (outside) 1 200.100.100.168 (already exists)

  create a static translation for each of the other protocols (next to pop3, smtp, www), you want to pass from the dmz to the internet (you already did that for www, pop3 and smtp).

  Kind regards

  Tom

• Registration of pix 515 "authorized connections."

  Can someone tell me if it is possible to connect to a syslog "allowed connections."

  We have lists of access internal servers behind the Pix 515 with port forwarding.

  We want to connect all connections from internet to the external IP, two connections permits and denied.

  logging trap debug, does not record the allowed connections. I tried this. Is there another way this?

  Thanks in advance!

  Gregory Manglaris

  Network engineer

  [email protected] / * /.

  The pix records connections. These present yourself as a syslog message #30213 information and look like this "outside:207.207.58.100/32792 (207.207.58.100/32792) at inside:w.x.y.z/80 (a.b.c.d/80) built 529605 for incoming TCP connection.

  The IP address represented by w.x.y.z. will be the internal address of your host and the IP address represented by a.b.c.d is the public address of this host.