Cisco VPN Client 2801 router

Similar Questions

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• PIX: Cisco VPN Client connects but no routing

  Hello

  We have a Cisco PIX 515 with software 7.1 (2). He accepts Cisco VPN Client connections with no problems, but no routing does to internal networks directly connected to the PIX. For example, my PC is affected by the IP 172.16.2.57 and then ping does not respond to internal Windows server 172.16.0.12 or trying to RDP. The most irritating thing is that these attempts are recorded in the system log, but always ended with "SYN timeout", as follows:

  2009-01-06 23:23:01 Local4.Info 217.15.42.214% 302013-6-PIX: built 3315917 for incoming TCP connections (172.16.2.57/1283) outside:172.16.2.57/1283 inside: ALAI2 / 3389 (ALAI2/3389)

  2009-01-06 23:23:31 Local4.Info 217.15.42.214% 302014-6-PIX: TCP connection disassembly 3315917 for outside:172.16.2.57/1283 inside: ALAI2 / 3389 duration 0:00:30 bytes 0 SYN Timeout

  2009-01-06 23:23:31 Local4.Debug 217.15.42.214% 7-PIX-609002: duration of disassembly-outside local host: 172.16.2.57 0:00:30

  We tried to activate and deactivate "nat-control", "permit same-security-traffic inter-interface" and "permit same-security-traffic intra-interface", but the results are the same: the VPN connection is successfully established, but remote clients cannot reach the internal servers.

  I enclose the training concerned in order to understand the problem:

  interface Ethernet0

  Speed 100

  full duplex

  nameif outside

  security-level 0

  IP address xx.yy.zz.tt 255.255.255.240

  !

  interface Ethernet1

  nameif inside

  security-level 100

  172.16.0.1 IP address 255.255.255.0

  !

  access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.255.0 172.16.2.56 255.255.255.248

  !

  access extensive list ip 172.16.0.0 outside_cryptomap_dyn_20 allow 255.255.255.0 172.16.2.56 255.255.255.248

  !

  VPN_client_group_splitTunnelAcl list standard access allowed 172.16.0.0 255.255.255.0

  !

  IP local pool pool_vpn_clientes 172.16.2.57 - 172.16.2.62 mask 255.255.255.248

  !

  NAT-control

  Global xx.yy.zz.tt 12 (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 12 172.16.0.12 255.255.255.255

  !

  internal VPN_clientes group strategy

  attributes of Group Policy VPN_clientes

  xxyyzz.NET value by default-field

  internal VPN_client_group group strategy

  attributes of Group Policy VPN_client_group

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list VPN_client_group_splitTunnelAcl

  xxyyzz.local value by default-field

  !

  I join all the details of the cryptographic algorithms because the VPN is successfully completed, as I said at the beginning. In addition, routing tables are irrelevant in my opinion, because the inaccessible hosts are directly connected to the internal LAN of the PIX 515.

  Thank you very much.

  can you confirm asa have NAT traversal allow otherwise, activate it in asa and vpn clients try again.

  PIX / ASA 7.1 and earlier versions

  PIX (config) #isakmp nat-traversal 20

  PIX / ASA 7.2 (1) and later versions

  PIX (config) #crypto isakmp nat-traversal 20

• IPSec site to site VPN cisco VPN client routing problem and

  Hello

  I'm really stuck with the configuration of ipsec site to site vpn (hub to spoke, multiple rays) with cisco vpn remote client access to this vpn.

  The problem is with remote access - cisco vpn client access - I can communicate with hub lan - but I need also communication of all lans speaks of the cisco vpn client.

  There are on the shelves, there is no material used cisco - routers DLINK.

  Someone told me that it is possible to use NAT to translate remote access IP-lan-HUB customers and thus allow communication - but I'm unable to set up and operate.

  Can someone help me please?

  Thank you

  Peter

  RAYS - not cisco devices / another provider

  Cisco 1841 HSEC HUB:

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key x xx address no.-xauth

  !

  the group x crypto isakmp client configuration

  x key

  pool vpnclientpool

  ACL 190

  include-local-lan

  !

  86400 seconds, duration of life crypto ipsec security association

  Crypto ipsec transform-set esp-3des esp-sha-hmac 1cisco

  !

  Crypto-map dynamic dynmap 10

  Set transform-set 1cisco

  !

  card crypto ETH0 client authentication list userauthen

  card crypto isakmp authorization list groupauthor ETH0

  client configuration address card crypto ETH0 answer

  ETH0 1 ipsec-isakmp crypto map

  set peer x

  Set transform-set 1cisco

  PFS group2 Set

  match address 180

  card ETH0 10-isakmp ipsec crypto dynamic dynmap

  !

  !

  interface FastEthernet0/1

  Description $ES_WAN$

  card crypto ETH0

  !

  IP local pool vpnclientpool 192.168.200.100 192.168.200.150

  !

  !

  overload of IP nat inside source list LOCAL interface FastEthernet0/1

  !

  IP access-list extended LOCAL

  deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  deny ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  IP 192.168.7.0 allow 0.0.0.255 any

  !

  access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  !

  How the DLINK has been configured for traffic between the site to site VPN subnets? You are able to add multiple remote subnets on DLINK? If you can, then you must add the pool of Client VPN subnet.

  Alternatively, if you cannot add multiple subnet on DLINK router, you can change the pool of Client VPN 192.168.6.0/24, and on the crypto ACL between the site to site VPN, you must edit the 180 existing ACL

  DE:

  access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 180 allow ip 192.168.200.0 0.0.0.255 192.168.1.0 0.0.0.255

  TO:

  access-list 180 allow ip 192.168.6.0 0.0.1.255 192.168.1.0 0.0.0.255

  Also change the ACL 190 split tunnel:

  DE:

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.200.0 0.0.0.255

  TO:

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.6.0 0.0.0.255

  access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255

  Finally, replace the remote subnet 192.168.7.0/255.255.255.0 192.168.6.0/255.255.254.0 DLINK.

  Hope that helps.

• Cisco VPN Client and Windows XP VPN Client IPSec to ASA

  I configured ASA for IPSec VPN via Cisco VPN Client and XP VPN client communications. I can connect successfully with Cisco VPN Client, but I get an error when connecting with the XP client. Debugging said "misconfigured groups and transport/tunneling mode" I know, they use different methods of transport and tunneling, and I think that I have configured both. Take a look at the config.

  PS a funny thing - when I connect with client VPN in Windows Server 2003, I have no error. The only difference is that client XP is behind an ADSL router and client server is directly connected to the Internet on one of its public IP of interfaces. NAT in the case of XP can cause problems?

  Config is:

  !

  interface GigabitEthernet0/2.30

  Description remote access

  VLAN 30

  nameif remote access

  security-level 0

  IP 85.*. *. 1 255.255.255.0

  !

  access-list 110 scope ip allow a whole

  NAT list extended access permit tcp any host 10.254.17.10 eq ssh

  NAT list extended access permit tcp any host 10.254.17.26 eq ssh

  access-list extended ip allowed any one sheep

  access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh

  sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0

  tunnel of splitting allowed access list standard 192.168.121.0 255.255.255.0

  flow-export destination inside-Bct 192.168.1.27 9996

  IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0

  ARP timeout 14400

  global (outside-Baku) 1 interface

  global (outside-Ganja) interface 2

  NAT (inside-Bct) 0 access-list sheep-vpn

  NAT (inside-Bct) 1 access list nat

  NAT (inside-Bct) 2-nat-ganja access list

  Access-group rdp on interface outside-Ganja

  !

  Access remote 0.0.0.0 0.0.0.0 85.*. *. 1 2

  Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1

  Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1

  Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1

  Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1

  Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1

  Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1

  Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1

  Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1

  dynamic-access-policy-registration DfltAccessPolicy

  Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT

  Crypto ipsec transform-set newset aes - esp esp-md5-hmac

  Crypto ipsec transform-set esp-3des esp-md5-hmac vpnclienttrans

  Crypto ipsec transform-set vpnclienttrans transport mode

  Crypto ipsec transform-set esp-3des esp-md5-hmac raccess

  life crypto ipsec security association seconds 214748364

  Crypto ipsec kilobytes of life security-association 214748364

  raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

  vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1

  card crypto interface for remote access vpnclientmap

  crypto isakmp identity address

  ISAKMP crypto enable vpntest

  ISAKMP crypto enable outside-Baku

  ISAKMP crypto enable outside-Ganja

  crypto ISAKMP enable remote access

  ISAKMP crypto enable Interior-Bct

  crypto ISAKMP policy 30

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  No encryption isakmp nat-traversal

  No vpn-addr-assign aaa

  Telnet timeout 5

  SSH 192.168.1.0 255.255.255.192 outside Baku

  SSH 10.254.17.26 255.255.255.255 outside Baku

  SSH 10.254.17.18 255.255.255.255 outside Baku

  SSH 10.254.17.10 255.255.255.255 outside Baku

  SSH 10.254.17.26 255.255.255.255 outside-Ganja

  SSH 10.254.17.18 255.255.255.255 outside-Ganja

  SSH 10.254.17.10 255.255.255.255 outside-Ganja

  SSH 192.168.1.0 255.255.255.192 Interior-Bct

  internal vpn group policy

  attributes of vpn group policy

  value of DNS-server 192.168.1.3

  Protocol-tunnel-VPN IPSec l2tp ipsec

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value split tunnel

  BCT.AZ value by default-field

  attributes global-tunnel-group DefaultRAGroup

  raccess address pool

  Group-RADIUS authentication server

  Group Policy - by default-vpn

  IPSec-attributes tunnel-group DefaultRAGroup

  pre-shared-key *.

  Hello

  For the Cisco VPN client, you would need a tunnel-group name configured on the ASA with a pre-shared key.

  Please see configuration below:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  or

  http://tinyurl.com/5t67hd

  Please see the section of tunnel-group config of the SAA.

  There is a tunnel-group called "rtptacvpn" and a pre-shared key associated with it. This group name is used by the VPN Client Group name.

  So, you would need a specific tunnel-group name configured with a pre-shared key and use it on the Cisco VPN Client.

  Secondly, because you are behind a router ADSL, I'm sure that's configured for NAT. can you please activate NAT - T on your ASA.

  "crypto isakmp nat-traversal.

  Thirdly, change the transformation of the value

  raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

  Let me know the result.

  Thank you

  Gilbert

• Configuration of Cisco for Cisco VPN Client ASA 5505

  Our firm has finally made the move from Sonicwall Cisco for our SMB customers. Got our first customer with a VPN site-to site solid and you have configured the main router for connections via the Cisco VPN Client VPN Wizard.

  When I install the VPN Client on desktop computers that does not capture all the necessary options (unless you have a SSL VPN). I guess that there is a process that I am missing to export a connection profile that Cisco VPN Client users can import for their connection.

  There step by step guides to create the connection profile file to distribute to customers?

  Hello

  The ASDM wizard is for the configuration on the SAA. This wizard will help you complete the VPN configuration on the end of the ASA.

  You will need to set the same in the client, so that they can negotiate and connect.

  Input connection in the client field, that's what you want to be seen that on the VPN client - it can be any name

  Host will be the external ip address of the ASA.

  Group options:

  name - same tunnel as defined on the ASA group
  Password - pre-shared as on ASA.

  Confirm password - same pre-shared key.

  Once this is over, you will see the customer having an entry same as a login entry. You must click on connect there. He will be a guest user and the password. Please enter the login crendentials. VPN connects.

  You can distribute the .pcf file that is formed at the place mentioned in the post above. Once the other client receive the .pcf, they need to import it by clicking this tab on the VPN client.

  Kind regards

  Anisha

• RV120 VPN with full Cisco VPN Client?

  Is it possible to configure the RV120 for a VPN IPsec for use with the complete Cisco VPN client?

  I tried, but it does not appear to support "Goup of authentication.

  I see in the confi router I can put a PSK, but the complete VPN client seems only accecpt "Goup authentication."

  I managed on the basis for the work "Fast VPN", how it works is beyond me, because he does not appear to create an adapter with an IP address or anything on the local line, and I didn't even create a VPN policy...

  Or put another way, what alternative (Free) VPN clients are there to work with the RV120?

  Try the following link for instructions for Cisco VPN and the SA500:

  http://www.Cisco.com/en/us/docs/security/multi_function_security/multi_function_security_appliance/sa_500/TechNote/note/SA500_vpnclient_appnote.PDF

  I hope this helps.

  Thank you

  Rick Roe

  Cisco Small Business Support Center

• Using Cisco VPN Client VPN

  Is it possible to use a private network virtual created with the WRVS4400N router with VPN Client from Cisco Systems (ver 5) software? (Although QuickVPN works very well.)

  Is it possible to use with Account customer VPN mode? Or is it possible to use with IPSec VPN (Tunnel) mode? If so, please provide together how to client-side and the router. Thank you!

  Unfortunately Small Business routers are not compatible with the Cisco VPN Clients. The Cisco VPN Clients have more parameters that are not available in the materials of the series of small businesses, so all we can use is the application of QVPN.

• Cisco VPN Client

  Hello

  I would like to know why when it failed to connect to the private network through the Cisco VPN client and trying to establish an Internet connection, the connection Internet.

  Thanks in advance,

  SK

  Which would be configured on the vpn, firewall/router endpoint etc..

• Cisco VPN client, PIX, and proxy

  Hi.I have problem in my company. We have users that go through a proxy server located in the DMZ of a PIX to the internet (allowed through the ACL of the DMZ on the outside, etc.). Which works very well.

  The problem arises when they use a Cisco VPN client to connect to another company, and they can no longer access the Internet, but may work via VPN to a remote site (client has been authorized by the Cisco PIX). Everything returns to normal when they no longer use the VPN client.

  Any ideas why this would happen?

  Without the proxy, browsing the internet via the vpn connection, or split tunnel is configured and you are leaving locally. If split tunnel is configured, the ip address of proxy server can overlap with the remote protected network.

  Fortunately, it is easy for you to know how the vpn is configured, just check the route details of vpn client statistics tab.

  Verify that the routing table local pc will also help you to solve this problem.

• How to allow access to a local area network behind the cisco vpn client

  Hi, my question is about how to allow access to a local area network behind the cisco vpn client

  With the help of:

  • Cisco 5500 Series Adaptive Security Appliance (ASA) that is running version 8.2 software
  • Cisco VPN Client version 5.0 software

  Cisco VPN client allows to inject a local routes in the routing table Cisco ASA?

  Thank you.

  Hi Vladimir,.

  Unfortunately this is not a supported feature if you connect through the VPN Client. With VPN Client, that the VPN Client can access the VPN Client LAN host/local machine, not host from the local network to business as customer VPN is not designed for access from the local company network, but to the local corporate network.

  If you want to access from your local business to your LAN network, you need to configure LAN-to-LAN tunnel.

• multi-site VPN with just the cisco vpn client

  Hello everyone

  Please I need your help.

  We have a headquarters office and up to 60 is BranchOffice, we want to create VPN network between its. so let's deploy 2 router cisco esy vpn server with HA (HSRP) at the Headquarters Office and all branches have Connection ADSL and they will use just the cisco vpn client to connect to the Headquarters Office.

  My question is: is it possible to do it just with the client vpn cisco without purchased for any exercise bracnh a cisco router to create an ipsec tunnel because it is so expensive?

  It depends on if the routers to offices can handle NAT with several internal VPN clients to 1 IP address. Most of the new material should be fine. Keep in mind the maximum limit of the VPN client, with 60 agencies and 5 people each of whom you are above the limit.

  Michael

  Please note all useful posts

• Another problem with the configuration of Cisco VPN Client access VPN Site2site

  We have a Cisco ASA 5505 at our CORP. branch I configured the VPN Site2Site to our COLO with a Juniper SRX220h, to another site works well, but when users access the home Cisco VPN client, they cannot ping or SSH through the Site2Site.  JTACS contacted and they said it is not on their end, so I tried to contact Cisco TAC, no support.  So here I am today, after for the 3 days (including Friday of last week) of searching the Internet for more than 6 hours per day and try different examples of other users. NO LUCK. The VPN client shows the route secure 10.1.0.0

  Sorry to post this, but I'm frustrated and boss breathing down my neck to complete it.

  CORP netowrk 192.168.1.0

  IP VPN 192.168.12.0 pool

  Colo 10.1.0.0 internal ip address

  Also, here's an example of my config ASA

  : Saved

  :

  ASA Version 8.2 (1)

  !

  hostname lwchsasa

  names of

  name 10.1.0.1 colo

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  backup interface Vlan12

  nameif outside_pri

  security-level 0

  IP 64.20.30.170 255.255.255.248

  !

  interface Vlan12

  nameif backup

  security-level 0

  IP 173.165.159.241 255.255.255.248

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  switchport access vlan 12

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  object-group network NY

  object-network 192.168.100.0 255.255.255.0

  BSRO-3387 tcp service object-group

  port-object eq 3387

  BSRO-3388 tcp service object-group

  port-object eq 3388

  BSRO-3389 tcp service object-group

  EQ port 3389 object

  object-group service tcp OpenAtrium

  port-object eq 8100

  object-group service Proxy tcp

  port-object eq 982

  VOIP10K - 20K udp service object-group

  10000 20000 object-port Beach

  the clientvpn object-group network

  object-network 192.168.12.0 255.255.255.0

  APEX-SSL tcp service object-group

  Description of Apex Dashboard Service

  port-object eq 8586

  object-group network CHS-Colo

  object-network 10.1.0.0 255.255.255.0

  the DM_INLINE_NETWORK_1 object-group network

  object-network 192.168.1.0 255.255.255.0

  host of the object-Network 64.20.30.170

  object-group service DM_INLINE_SERVICE_1

  the purpose of the ip service

  ICMP service object

  service-object icmp traceroute

  the purpose of the service tcp - udp eq www

  the tcp eq ftp service object

  the purpose of the tcp eq ftp service - data

  the eq sqlnet tcp service object

  EQ-ssh tcp service object

  the purpose of the service udp eq www

  the eq tftp udp service object

  object-group service DM_INLINE_SERVICE_2

  the purpose of the ip service

  ICMP service object

  EQ-ssh tcp service object

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 clientvpn object-group

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group NY

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo

  inside_nat0_outbound list of allowed ip extended access any 192.168.12.0 255.255.255.0

  outside_pri_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group NY

  outside_pri_access_in list extended access permit tcp any interface outside_pri eq www

  outside_pri_access_in list extended access permit tcp any outside_pri eq https interface

  outside_pri_access_in list extended access permit tcp any interface outside_pri eq 8100

  outside_pri_access_in list extended access permit tcp any outside_pri eq idle ssh interface

  outside_pri_access_in list extended access permit icmp any any echo response

  outside_pri_access_in list extended access permit icmp any any source-quench

  outside_pri_access_in list extended access allow all unreachable icmp

  outside_pri_access_in list extended access permit icmp any one time exceed

  outside_pri_access_in list extended access permit tcp any 64.20.30.168 255.255.255.248 eq 8586

  levelwingVPN_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0

  levelwingVPN_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.255.0

  outside_pri_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo

  backup_nat0_outbound list extended access allowed object-group DM_INLINE_NETWORK_1 192.168.12.0 ip 255.255.255.0

  outside_pri_cryptomap_1 list extended access allow DM_INLINE_SERVICE_2 of object-group 192.168.1.0 255.255.255.0 10.1.0.0 255.255.255.0

  outside_19_cryptomap to access extended list ip 192.168.12.0 allow 255.255.255.0 10.1.0.0 255.255.255.0

  inside_nat0_outbound_1 to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo

  VPN-Corp-Colo extended access list permits object-group DM_INLINE_SERVICE_1 192.168.12.0 255.255.255.0 10.1.0.0 255.255.255.0

  Note to OUTSIDE-NAT0 NAT0 customer VPN remote site access-list

  OUTSIDE-NAT0 192.168.12.0 ip extended access list allow 255.255.255.0 10.1.0.0 255.255.255.0

  L2LVPN to access extended list ip 192.168.12.0 allow 255.255.255.0 10.1.0.0 255.255.255.0

  pager lines 24

  Enable logging

  debug logging in buffered memory

  exploitation forest asdm warnings

  record of the rate-limit unlimited level 4

  destination of exports flow inside 192.168.1.1 2055

  timeout-rate flow-export model 1

  Within 1500 MTU

  outside_pri MTU 1500

  backup of MTU 1500

  local pool LVCHSVPN 192.168.12.100 - 192.168.12.254 255.255.255.0 IP mask

  no failover

  ICMP unreachable rate-limit 100 burst-size 5

  ICMP allow any inside

  ICMP allow any outside_pri

  don't allow no asdm history

  ARP timeout 14400

  NAT-control

  interface of global (outside_pri) 1

  Global 1 interface (backup)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 0 inside_nat0_outbound_1 list of outdoor access

  NAT (inside) 1 0.0.0.0 0.0.0.0

  NAT (outside_pri) 0-list of access OUTSIDE-NAT0

  backup_nat0_outbound (backup) NAT 0 access list

  static TCP (inside outside_pri) interface https 192.168.1.45 https netmask 255.255.255.255 dns

  static TCP (inside outside_pri) interface 192.168.1.45 www www netmask 255.255.255.255 dns

  static TCP (inside outside_pri) interface 8586 192.168.1.45 8586 netmask 255.255.255.255 dns

  static (inside, inside) tcp interface 8100 192.168.1.45 8100 netmask 255.255.255.255 dns

  Access-group outside_pri_access_in in the outside_pri interface

  Route 0.0.0.0 outside_pri 0.0.0.0 64.20.30.169 1 track 1

  Backup route 0.0.0.0 0.0.0.0 173.165.159.246 254

  Timeout xlate 03:00

  Conn Timeout 0:00:00 half-closed 0:30:00 udp icmp from 01:00 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 01:00 uauth uauth absolute inactivity from 01:00

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA authentication enable LOCAL console

  AAA authentication http LOCAL console

  the ssh LOCAL console AAA authentication

  http server enable 981

  http 192.168.1.0 255.255.255.0 inside

  http 0.0.0.0 0.0.0.0 outside_pri

  http 0.0.0.0 0.0.0.0 backup

  SNMP server group Authentication_Only v3 auth

  SNMP-server host inside 192.168.1.47 survey community lwmedia version 2 c

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Sysopt connection tcpmss 1200

  monitor SLA 123

  type echo protocol ipIcmpEcho 216.59.44.220 interface outside_pri

  Annex ALS life monitor 123 to always start-time now

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set esp-3des-sha1 esp-3des esp-sha-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  Crypto ipsec df - bit clear-df outside_pri

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  card crypto outside_pri_map 1 match address outside_pri_1_cryptomap

  card crypto outside_pri_map 1 set pfs

  peer set card crypto outside_pri_map 1 50.75.217.246

  card crypto outside_pri_map 1 set of transformation-ESP-AES-256-MD5

  card crypto outside_pri_map 2 match address outside_pri_cryptomap

  peer set card crypto outside_pri_map 2 216.59.44.220

  card crypto outside_pri_map 2 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  86400 seconds, duration of life card crypto outside_pri_map 2 set security-association

  card crypto outside_pri_map 3 match address outside_pri_cryptomap_1

  peer set card crypto outside_pri_map 3 216.59.44.220

  outside_pri_map crypto map 3 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_pri_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  card crypto outside_pri_map interface outside_pri

  crypto isakmp identity address

  ISAKMP crypto enable outside_pri

  crypto ISAKMP policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 10

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 30

  preshared authentication

  aes-256 encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 50

  preshared authentication

  aes encryption

  md5 hash

  Group 2

  life 86400

  !

  track 1 rtr 123 accessibility

  Telnet timeout 5

  SSH 192.168.1.0 255.255.255.0 inside

  SSH timeout 5

  Console timeout 0

  management-access inside

  dhcpd auto_config outside_pri

  !

  dhcpd address 192.168.1.51 - 192.168.1.245 inside

  dhcpd dns 8.8.8.8 8.8.4.4 interface inside

  rental contract interface 86400 dhcpd inside

  dhcpd field LM inside interface

  dhcpd allow inside

  !

  a basic threat threat detection

  statistical threat detection port

  Statistical threat detection Protocol

  Statistics-list of access threat detection

  a statistical threat detection host number rate 2

  no statistical threat detection tcp-interception

  WebVPN

  port 980

  allow inside

  Select outside_pri

  enable SVC

  attributes of Group Policy DfltGrpPolicy

  VPN-idle-timeout no

  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

  internal GroupPolicy2 group strategy

  attributes of Group Policy GroupPolicy2

  Protocol-tunnel-VPN IPSec svc

  internal levelwingVPN group policy

  attributes of the strategy of group levelwingVPN

  Protocol-tunnel-VPN IPSec svc webvpn

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list levelwingVPN_splitTunnelAcl

  username password encrypted Z74.JN3DGMNlP0H2 privilege 0 aard

  aard attribute username

  VPN-group-policy levelwingVPN

  type of remote access service

  rcossentino 4UpCXRA6T2ysRRdE encrypted password username

  username rcossentino attributes

  VPN-group-policy levelwingVPN

  type of remote access service

  bcherok evwBWqKKwrlABAUp encrypted password username

  username bcherok attributes

  VPN-group-policy levelwingVPN

  type of remote access service

  rscott nIOnWcZCACUWjgaP encrypted password privilege 0 username

  rscott username attributes

  VPN-group-policy levelwingVPN

  sryan 47u/nJvfm6kprQDs password encrypted username

  sryan username attributes

  VPN-group-policy levelwingVPN

  type of nas-prompt service

  username, password cbruch a8R5NwL5Cz/LFzRm encrypted privilege 0

  username cbruch attributes

  VPN-group-policy levelwingVPN

  type of remote access service

  apellegrino yy2aM21dV/11h7fR password encrypted username

  username apellegrino attributes

  VPN-group-policy levelwingVPN

  type of remote access service

  username rtuttle encrypted password privilege 0 79ROD7fRw5C4.l5

  username rtuttle attributes

  VPN-group-policy levelwingVPN

  username privilege 15 encrypted password vJFHerTwBy8dRiyW levelwingadmin

  username password nbrothers Amjc/rm5PYhoysB5 encrypted privilege 0

  username nbrothers attributes

  VPN-group-policy levelwingVPN

  clong z.yb0Oc09oP3/mXV encrypted password username

  clong attributes username

  VPN-group-policy levelwingVPN

  type of remote access service

  username, password finance 9TxE6jWN/Di4eZ8w encrypted privilege 0

  username attributes finance

  VPN-group-policy levelwingVPN

  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

  type of remote access service

  IPSec-attributes tunnel-group DefaultL2LGroup

  Disable ISAKMP keepalive

  tunnel-group 50.75.217.246 type ipsec-l2l

  IPSec-attributes tunnel-group 50.75.217.246

  pre-shared-key *.

  Disable ISAKMP keepalive

  type tunnel-group levelwingVPN remote access

  tunnel-group levelwingVPN General-attributes

  address LVCHSVPN pool

  Group Policy - by default-levelwingVPN

  levelwingVPN group of tunnel ipsec-attributes

  pre-shared-key *.

  tunnel-group 216.59.44.221 type ipsec-l2l

  IPSec-attributes tunnel-group 216.59.44.221

  pre-shared-key *.

  tunnel-group 216.59.44.220 type ipsec-l2l

  IPSec-attributes tunnel-group 216.59.44.220

  pre-shared-key *.

  Disable ISAKMP keepalive

  !

  !

  !

  Policy-map global_policy

  !

  context of prompt hostname

  Cryptochecksum:ed7f4451c98151b759d24a7d4387935b

  : end

  Hello

  It seems to me that you've covered most of the things.

  You however not "said" Configuring VPN L2L that traffic between the pool of VPN and network camp should be in tunnel

  outside_pri_cryptomap to access extended list ip 192.168.12.0 allow 255.255.255.0 object-group CHS-Colo

  Although naturally the remote end must also the corresponding configurations for users of VPN clients be able to pass traffic to the site of the camp.

  -Jouni

• Cisco VPN Client follow-up

  Hello

  I have a Cisco 2821 and ASA 5510 VPN router in my network.

  Our remote users are using Cisco VPN Client 5.0.07 and I need to track on a server and keep their login information to generate reports for my manager.

  Could you please let me know how I can do this trick of surveillance?

  Thank you

  Mike

  It can be done by choosing one of three types of monitoring of the performance of the VPN:

  http://www.Cisco.com/en/us/docs/net_mgmt/vpn_solutions_center/1.1/user/guide/VPN_UG5.html

  I hope this helps!

• Cannot access remote resources - Cisco VPN Client

  I'm having a problem with my Cisco VPN Client. I am new to VPN configuration, so this is probably something easy I'm missing. I have a my internet gateway for my LAN 2611XM router and my VPN server. I do all my tests of a society with a high card laptop mobile broadband. VPN connects, but anytime I ping anything in the network Cabinet, he returned with the public IP address of the external interface. I have NAT overload configured so any network can access the internet, inside which it looks like may be causing my problem. I don't know how to fix it. My config running is attatched. No one knows what might happen.

  Oh, almost forgot to add. When I remove the nat overload on my interface fa0/1, the vpn will connect to any resource on the inside.

  Your nat configuration seems to be the origin of the problem. If you are using an ACL to match the source for NAT, then it will be necessary to add the line 1A refuse for the local ip pool for your vpn clients to one only. try that to see how it goes.

  Sent by Cisco Support technique iPhone App