Placement of IDS and IPS, inside or outside?

Similar Questions

• How IDS and IPS notify added new sound signatures?

  I was told that they do so by sending the email from some sort of mailing list.

  My questions are,

  1. is it any way, or the best way to do it?

  2. If the shipment is the only way, where can I join this mail list?

  Thank you

  Han

  Threat defense Bulletins can be found here.

  http://Tools.Cisco.com/Security/Center/bulletin.x?i=57

  To subscribe to the HTML version or the text in the list:

  To subscribe to the HTML version of the mailing list: send an email to [email protected] / * / with the subject "subscribe". (The content of the message does not matter). You will receive confirmation, instructions and a list policy statement.

  To subscribe to the version in plain text for the mailing list: send an email to [email protected] / * / with the subject "subscribe". (The content of the message does not matter). You will receive confirmation, instructions and a list policy statement.

  Please note that applications should be sent to [email protected] / * / or [email protected] / * / and not the list itself.

  Individuals must send messages from the account that will be subscribed to the list. We do not accept subscriptions for one account that are sent from a second account.

  Those wishing to subscribe to this mailing list may also send an e-mail message to [email protected] / * / requesting access.

• The ASA for FW and IPS options with high availability

  Question 1:

  -----------

  I'm looking for IPS solution for the customer and the verification of the ASA next part number;

  ASA5540-AIP20-K9

  (ASA 5540 appliance w / AIP-SSM-20, SW, HA, 4GE + 1FE, 3DES/AES)

  What does AP mean here - what software?

  In this case you have to buy a second unit (at the same price) for the recovery of?

  (I wondered if ASA has also a cost - efficient as PIX failover solution-discounted price for the unit of failover).

  If I choose the ASA VPN edition is it possible to add IPS inside module?

  Hello

  Q: what does AP means here - what software? In this case you have to buy a second unit (at the same price) for the recovery of?

  The "ASA5540-AIP20-K9" is only for 1 unit of ASA, with function of software HA (active/active, active / standby). You can add/buy another unit to achieve HA/recundancy.

  I think that the price of a unit all them is always the same, ASA has no unit to voluntarily make the function FO.

  Q: if I choose the ASA VPN edition is it possible to add IPS inside module?

  Large malicious Intrusion Prevention & mitigation program is included, as mentioned in the 'picture' 3 Security of the network to the VPN gateway"in:

  http://www.Cisco.com/en/us/products/ps6120/products_data_sheet0900aecd80402e3f.html

  Rgds,

  AK

• Place aligned EditField and BitmapField on PopupScreen

  Hello guys '

  I want to place aligned EditField and BitmapField on PopupScree. But I can't place these 2 fields.

  I used HorizontalFieldManager and VerticalFieldManager of the place. It does not work.

  HorizontalFieldManager hmanager = new HorizontalFieldManager();
  VerticalFieldManager vmanagerRight = new VerticalFieldManager();
  VerticalFieldManager vmanagerLeft = new VerticalFieldManager();
  
  statusLabel = new LabelField();
  direction = new Bitmap(15, 15);
  directionBitmap = new BitmapField(direction);
  
  vmanagerLeft.add(directionBitmap);
  vmanagerRight.add(statusLabel);
  
  hmanager.add(vmanagerLeft);
  hmanager.add(vmanagerRight);
  
  progressPopup = new PopupScreen(hmanager);
  
  ...
  

  What solution is the best?

  Tnx guys

  What you see?  The fields appearing at all or are they not be presented as you wish?

• I had problems with my gc, cleaned and he is now allowed outside my control file system system, that it will take place at 68% and stops running

  I had problems with my graphics card cleaned and it works well apart from the system of checking file system on C: turns 68% and stops. If I have to cancel the computer checking seems to work ok, or is it?

  I guess that Mark_S_Sloan is talking about chkdsk /r or running a disk check with fixed error on a restart. so I would say that what I used to say the performance is chkdsk:

  The chkdsk/r can take a long time to complete depending on the size of the volume, the amount of data on the volume, the speed of the system and what chkdsk is to do.  It take about 2 hours for chkdsk/r run on one of the volumes of my1TB (I'm a right that I rarely run).

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.  Give him a chance.

  @Imran M - Microsoft technical support engineer:

  Don't you know that the performance of the auditor of the filesystem (sfc/scannow) does not provide a percentage of completion?  Have you ever used it?

  He also really tell you anything about what he did, or could have done when it is executed even if she finds something to do.

  Everything you see in the Event Viewer system log are messages like this:

  Event type: Information
  Event source: Windows File Protection
  Event category: no
  Event ID: 64016
  Analysis of file File Protection Windows has been started.

  .. few time later...

  Event type: Information
  Event source: Windows File Protection
  Event category: no
  Event ID: 64017
  Windows File Protection file analysis completed successfully.

  Even if sfc/scannow find something to do, you will know about it, because it is not connected.

  That's why use sfc/scannow still more of a waste of time.

• PartialTrigger of different region and targets inside the iterator.

  Hello

  I use 11.1.1.6. Basically, I've got A Taskflow is a region that has inside an iterator that creates several commandLinks. I need to refresh a component of the parent page (one is the region) so I will try to accomplish the task using partialTriggers on components of commandLinks.

  My region ID is = r1, so I put the partialTrigger = "r1:iter1:cl1", but does not work. If I put a commandButton control in my taskflow region but outside of the iterator and defining the partialTriggers = "r1:cb1" then it works.

  An idea to solve this, or a different approach?

  Never mind. This works if partialTrigger = "r1:iter1:cl1" is used. It was that I was wrong using IDs.

• Choose and place using labview and or vision acquisition

  Hello world

  I'm doing a project studying on Vision guided pick and place of a robot (abb) industrial. I would like to know the steps involved in the creation of the block.

  I locate the object, move his webcam cooordinates. Then made a pattern match, and would send the cooordinates to the microcontroller. then from microcontroller for control of robot... then the industrial robot should choose the object and place it in a predefined area...

  I would be extremely grateful if you guys can help me because I am new to LabView.

  Thank you

  Pradeep.M

  ([email protected])

  What you describe is quite complex, but here are a few tips.  The key is to establish a correlation between the coordinate system of the robot to the coordinate system of the camera.  I guess that the camera is statically located above the pick-up area?  I move the robot at each corner of the frame to its choice position vertically and note the position of the robot at these locations.  These 4 points in space will be correlated to X, coordinates of pixels in the camera image.  Basically, you need to write a sub - VI with entries being pixel X and is coordinated and coordinates output being the robot.

  Writing a test application saying the robot to get pixel location to any X, Y in the framework to test your Subvi.  If this does not work, then you need to set up a correspondence to the model.  You probably want to do a geometric pattern match.  Take a look at this example: http://zone.ni.com/devzone/cda/epd/p/id/5555

  You will need your pattern match algorithm to return both the coordinates for your robot, and the orientation of the tool needed for good pick up the object (if the pick-and-place robot tool requires to be in a specific direction).  If it's basically up to you will convert the object X, Y and rotation angle in the framework that you receive correspondence from model to any coordinate system, the robot uses.

  The placement algorithm could be simply an adjustment of orientation to the object being investment and then investment positions could be an array of coordinates of robot which you browse after each pick.

  Be sure to implement security mechanisms in your algorithms so that the robot can never go somewhere outside of a safe range of coordinates.

• Techniques need more details 4250XL IPS and IPS-4255

  4250XL IDS launched before the IPS technology, am I right?

  Can I deploy a 4250XL ID as an IPS, if yes, then it's true to upgrade this version IDS 4.1 to IPS ver 5.0

  I add 4 10/100/1000BaseT ports on ID 4250XL.

  Because, I have to deploy IPS to 1 Gbps throughput.

  and I could not find an IPS in CISCO will produce 1 Gbit/s with 4-port 10/100/1000BaseT.

  How many simultaneous sessions support IPS 4200 series.

  How can I use feature Redundant Power Supply on IPS-4255.

  Technical documentation 42xx is linked off the coast of http://www.cisco.com/go/ips. I don't know if IPS 5.0 information is still (it's kinda new). There is no option RPS for the 4240/4255, but recommends the use of a UPS would be justified for packaging line if you have unreliable power.

  There is no provision for failover in the transducer (other than the bypass mode), but there are drawings (I hope bound off the page that I mentioned above) to do network active / standby designs.

  The 4240 and 4255 do not have redundant storage... they have no HDD due to reliability problems. They run a flash and ram disk configuration.

• How do a search for IPS inside a html tag for a string?

  I need to make the search for cisco IPS of the chain eb 03% 59% eb % 05% e8% f8% ff % ff % ff % 49% 49% 49 inside any *.html

  I tried the http service (ask Regex) and AIC http (Msg body Patten) but no luck

  Thank you

  Using IDM

  Configuration > definition Signature > Assistant personal than Signature

  Select TCP as the Protocol to inspect >

  Click on the single TCP connection option button >

  Select other as the type of service >

  Enter the parameters for signature >

  Select your action event

  String Regex class enter eb 03% 59% eb % 05% e8% f8% ff % ff ff 49% 49% 49%

  Enter 80 in the field of service Ports

  M.

• Redirection of port from inside to outside. Also of ICMP on the inside.

  I'm working on a FWSM using code 2.2 (1) and I would like to proxies all web requests to a box of squid of the interface from the inside to the outside and I am using the static command. All the examples I've seen pass from outside to inside. I tried the following and it doesn't work.

  Internal network interface: LabA

  Box of squid on the external network to IP: 1.1.1.1 answer on port 8080.

  Command:

  static (LabA, outside) interface 8080 tcp 1.1.1.1 80 netmask 255.255.255.255 0 0

  The question I have, is the static command above works of highest to lowest? If not, is there a better way to solve this problem other than to put a map of the route on the interface routed to the MSFC?

  Second problem, I can't ping my inside interfaces from the outside? I can ping interfaces of security inside/down level of the Interior. Is this a problem where you can leave the same interface that happened you? I encouraged icmp in access lists.

  Thanks for the help.

  Static defines a permanent translation betwwen two interfaces and is used for traffic between these two interfaces in EITHER DIRECTION. The problem you are experiencing probably is the static ports (8080 and 80) are the port of destination. According to which direction your traffic flowing port 8080 or 80 can be the source port, and in this case this static has no effect.

  Regarding your question ICMP, you cannot ping a PIX/FWSM to another interface interface. This was always the way it works, and there is no way around it. To test connectivity between the interfaces you have to ping a host interface to another host out of another interface.

• Remote access ASA - cannot access devices inside or outside

  Hello

  I have an ASA550: I configured a VPN IPSEC and can connect to the ASA and I can access the CLI.

  I can access internal devices of the ASA and I can access the internet.

  However, I can't access internal devices or over the internet from the computer connected to IPSec.

  Any help is appreciated!

  Here is the config:

  ASA Version 8.2 (5)

  !

  host name asa

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 10.47.70.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.240

  !

  passive FTP mode

  access extensive list ip 10.47.60.0 inside_nat0_outbound allow 255.255.255.0 10.47.70.0 255.255.255.0

  outside_access_in list extended access permit icmp any one

  outside_access_in list extended access permit udp any any eq

  outside_1_cryptomap list of allowed ip extended access all 10.47.60.0 255.255.255.0

  IP local pool hze_dhcp 10.47.60.10 - 10.47.60.41 mask 255.255.255.0

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  dynamic-access-policy-registration DfltAccessPolicy

  Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA

  Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Crypto isakmp nat-traversal 3600

  management-access inside

  dhcpd dns 10.47.70.3

  dhcpd option 3 ip 10.47.70.1

  !

  dhcpd address 10.47.70.50 - 10.47.70.81 inside

  dhcpd allow inside

  !

  WebVPN

  internal DefaultRAGroup group strategy

  attributes of Group Policy DefaultRAGroup

  value of server DNS 8.8.8.8

  Protocol-tunnel-VPN IPSec l2tp ipsec

  attributes global-tunnel-group DefaultRAGroup

  address hze_dhcp pool

  Group Policy - by default-DefaultRAGroup

  IPSec-attributes tunnel-group DefaultRAGroup

  pre-shared key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  !

  global service-policy global_policy

  context of prompt hostname

  Hello

  I don't think you have dynamic PAT configured for traffic from the VPN Client user who is supposed to browse the Internet through the connection WAN ASAs.

  Try adding

  NAT (outside) 1 10.47.60.0 255.255.255.0

  Also, the "packet-tracer" you question is not simulate the connection from the VPN Client. The user of the VPN Client is not behind the 'inside' interface and the Clients VPN address space does not include the IP 10.47.70.20.

  When the Client VPN connection is active, you can use the command "packet - trace"

  entry Packet-trace out tcp 10.47.60.x 12345 8.8.8.8 80

  While of course, replace 'x' with the real IP that the user got to the ASA

  -Jouni

• photos not in the same place on LR and in the computer library, help!

  When I save LR or import into LR the photo is saved outside the main tree for my work which is the place, it is meant to save. It appears in its own folder with only a label to date 2015-9-22. In the library of the computer to PSD without title-5254-edit. The same thing happens when I import. How can I fix so I can return to my LR? At the moment I can't use because when I work on or import new pictures, they're caught in this mess. Help, please!

  

  

  One person on another forum suggested I use the parent show file.  This brought me back to the original problem I had and have solved temporarily.  However, the next time I tried similarly to the PS or import from card reader the above repeats.  I need to remove LR and recharge?  This will help?  I'm desperate.  I can't do anything on LR until this problem is solved!

  Now, he has moved to the bottom of this section and changed its name.  Try to pass one of these posts just tells me that the photo is already in this folder, it is in the library of the computer.

  

  Hi AFFshot,

  You must select the option "by date" in the destination on the import window section, you can change according to your requirement.

  See the screenshot

  

  Let us know if that helps.

  Kind regards

  Mohit

• By aligning transformed text (and other) inside StackFrame

  Good day guys! I have StackPane and (enlarged with scaleX and scaleY properties) scaling text inside the component node. When the text is aligned to the center of the pane (fi g. 1) there is no problem. But when I try to align left, right, or any other sides or corners then text positioned outside the component (fi g. 2). How can I solve this problem? Text have TextBoundsType.VISUAL limits. Thank you!

  Link to the image... PEAK. 1 gray text aligned at the center of the stack pane. StackPane.setAlignment (Pos.CENTER)	Link to the image... PEAK. 2 grey text aligned to the left of the stack pane. StackPane.setAlignment (Pos.CENTER_LEFT)

  You could try to wrap the text in a group. I tested in the stage Builder, and it seemed to work ok with various alignments of StackPane:

• A query related to ProgressBar and implementation inside the container

  Hello

  I tried an example with Flex3 ProgressBar. I write the scenario in which it was OK in one case and bad in another case.

  Please tell me what's not here in the case of wrong:

  The program is linked to:
  I have the button when click on that I load the Image. There is no button and its event listener mentioned here.

  Correct approach:

  This works also very well the Image and ProgressBar are in the same container called HBox

  < mx:HBox >

  < mx:Image id = autoload "image" = "false" / >

  < mx:ProgressBar id = "MYPB" source = "{image}" / >

  < / mx:HBox >

  
  Wrong approach:
  

  Below does not work as I placed the ProgressBar outside the container called as HBox

  < mx:HBox >

  < mx:Image id = autoload "image" = "false" / >

  < / mx:HBox >

  < mx:ProgressBar id = "MYPB" source = "{image}" / >

  Please share your ideas like why it behaves in this way.

  Hi Kiran.

  I don't think that either the approach is wrong, it no way performed by placing the ProgressBar inside a container or outside the container.

  Run the sample application below. It loads to the two approaches.

  
  http://www.Adobe.com/2006/mxml"layout ="vertical">
  
          public function loadImage1 (): void {}
  Image1. Load('assets/liazon_logo.png');
  }
             
  public function loadImage2 (): void {}
  Image2. Load('assets/liazon_logo.png');
  }
  ]]>
     

  
   
  
  

  
   
   
  

  If this post answers your question or assistance, please mark it as such.

  Thank you

  Jean Claude Chari

• Gradient fills that radiate to the inside or outside

  I would like to be able to create a gradient between the paths are creating buy using the command "path offset."  I want the filling to go either from the outside path inward or vice versa.  Is this possible?  I'm very very very very new to illustrator and I've been Googling for hours but I don't think I know the exact terminology to search for.  I have attached an image using a circle that demonstrates the effect I'm after.  But I would like to apply to paths in weird shape... but always have a smooth gradient of the path from the outside to the inside.

  DB,

  I would like to be able to create a gradient between the paths are creating buy using the command "path offset."

  In fact, you describe the first step in the creation of the mixture for the paths of contour. Simply select both paths and:

  (2) object > blending Options, choose align to the path, especially if you can rotate / whatever later and choose colors or the steps specified; with a number suitable, the latter will normally result in a smaller file, and it is necessary if one or two objects has a gradient;

  (3) object > blend > make.