Remote access ASA - cannot access devices inside or outside
Hello
I have an ASA550: I configured a VPN IPSEC and can connect to the ASA and I can access the CLI.
I can access internal devices of the ASA and I can access the internet.
However, I can't access internal devices or over the internet from the computer connected to IPSec.
Any help is appreciated!
Here is the config:
ASA Version 8.2 (5)
!
host name asa
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 10.47.70.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP x.x.x.x 255.255.255.240
!
passive FTP mode
access extensive list ip 10.47.60.0 inside_nat0_outbound allow 255.255.255.0 10.47.70.0 255.255.255.0
outside_access_in list extended access permit icmp any one
outside_access_in list extended access permit udp any any eq
outside_1_cryptomap list of allowed ip extended access all 10.47.60.0 255.255.255.0
IP local pool hze_dhcp 10.47.60.10 - 10.47.60.41 mask 255.255.255.0
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
dynamic-access-policy-registration DfltAccessPolicy
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA
Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 3600
management-access inside
dhcpd dns 10.47.70.3
dhcpd option 3 ip 10.47.70.1
!
dhcpd address 10.47.70.50 - 10.47.70.81 inside
dhcpd allow inside
!
WebVPN
internal DefaultRAGroup group strategy
attributes of Group Policy DefaultRAGroup
value of server DNS 8.8.8.8
Protocol-tunnel-VPN IPSec l2tp ipsec
attributes global-tunnel-group DefaultRAGroup
address hze_dhcp pool
Group Policy - by default-DefaultRAGroup
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
!
global service-policy global_policy
context of prompt hostname
Hello
I don't think you have dynamic PAT configured for traffic from the VPN Client user who is supposed to browse the Internet through the connection WAN ASAs.
Try adding
NAT (outside) 1 10.47.60.0 255.255.255.0
Also, the "packet-tracer" you question is not simulate the connection from the VPN Client. The user of the VPN Client is not behind the 'inside' interface and the Clients VPN address space does not include the IP 10.47.70.20.
When the Client VPN connection is active, you can use the command "packet - trace"
entry Packet-trace out tcp 10.47.60.x 12345 8.8.8.8 80
While of course, replace 'x' with the real IP that the user got to the ASA
-Jouni
Tags: Cisco Security
Similar Questions
-
Remote access ASA, VPN and NAT
Hello
I try to get access to remote VPN work using a Cisco VPN client and ASA with no split tunneling. The VPN works a little, I can access devices inside when I connect, but I can't access the Internet. I don't see any errors in the log ASA except these:
1 Jul 04:59:15 % ASA-3-305006 gatekeeper: failed to create translation portmap for udp src outside:192.168.47.200/137 dst outside:192.168.47.255/137
1 Jul 04:59:15 % ASA-3-305006 gatekeeper: failed to create translation portmap for udp src outside:192.168.47.200/54918 dst outsidexx.xxx.xxx.xxx/53There is only one address public IP that is assigned to the external interface of DHCP. The Interior is 192.168.1.0/24 network which is PAT'ed to the external interface and the VPN network is 192.168.47.X.
I think my problem is that the net.47 is not NAT'ed out properly and I don't know how to put in place exactly. I can't understand how this is supposed to work since the net VPN technically provenance from the outside already.
Here are all the relevant config:
list of vpn access extended permits all ip 192.168.47.0 255.255.255.0
Within 1500 MTU
Outside 1500 MTU
IP local pool vpnpool 192.168.47.200 - 192.168.47.220 mask 255.255.255.0
IP verify reverse path to the outside interface
IP audit info alarm drop action
IP audit attack alarm drop action
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
Global interface (2 inside)
Global 1 interface (outside)
NAT (inside) 0-list of access vpn
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 2 192.168.47.0 255.255.255.0 outside
static (inside, outside) tcp 3074 XBOX360 3074 netmask 255.255.255.255 interface
static (inside, outside) udp 3074 XBOX360 3074 netmask 255.255.255.255 interface
public static (inside, outside) udp interface 88 88 XBOX360 netmask 255.255.255.255
public static tcp (indoor, outdoor) https someids netmask 255.255.255.255 https interfaceI can post more of the configuration if necessary.
Change ' nat (outside) 2 192.168.47.0 255.255.255.0 apart ' "NAT (2-list of vpn access outdoors outside)" gives these:
1 Jul 06:18:35 % gatekeeper ASA-3-305005: no group of translation not found for udp src outside:192.168.47.200/56003 dst outside:66.174.95.44/53
So, how I do right NAT VPN traffic so it can access the Internet?
A few things that needs to be changed:
(1) NAT exemption what ACL must be modified to be more specific while the traffic between the internal subnets and subnet pool vpn is not coordinated. NAT exemption takes precedence over all other statements of NAT, so your internet traffic from the vpn does not work.
This ACL:
list of vpn access extended permits all ip 192.168.47.0 255.255.255.0
Should be changed to:
extensive list of access vpn ip 192.168.47.0 255.255.255.0 allow
(2) you don't need statement "overall (inside) 2. Here's what to be configured:
no nat (outside) 2 192.168.47.0 255.255.255.0 outside
no global interface (2 inside)
NAT (outside) 1 192.168.47.0 255.255.255.0
(3) and finally, you must activate the following allow traffic back on the external interface:
permit same-security-traffic intra-interface
And don't forget to clear xlate after the changes described above and connect to your VPN.
Hope that helps.
-
Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network
I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well
Thank you
interface Ethernet0/0
Speed 100
full duplex
nameif outside
security-level 0
IP x.x.x.x 255.255.255.240
!
interface Ethernet0/1
Speed 100
full duplex
nameif inside
security-level 100
IP 10.88.10.254 255.255.255.0
!
interface Management0/0
Shutdown
nameif management
security-level 0
no ip address
!
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the PAT_to_Outside_ClassA object
10.88.0.0 subnet 255.255.0.0
network of the PAT_to_Outside_ClassB object
subnet 172.16.0.0 255.240.0.0
network of the PAT_to_Outside_ClassC object
Subnet 192.168.0.0 255.255.240.0
network of the LocalNetwork object
10.88.0.0 subnet 255.255.0.0
network of the RemoteNetwork1 object
Subnet 192.168.0.0 255.255.0.0
network of the RemoteNetwork2 object
172.16.10.0 subnet 255.255.255.0
network of the RemoteNetwork3 object
10.86.0.0 subnet 255.255.0.0
network of the RemoteNetwork4 object
10.250.1.0 subnet 255.255.255.0
network of the NatExempt object
10.88.10.0 subnet 255.255.255.0
the Site_to_SiteVPN1 object-group network
object-network 192.168.4.0 255.255.254.0
object-network 172.16.10.0 255.255.255.0
object-network 10.0.0.0 255.0.0.0
outside_access_in deny ip extended access list a whole
inside_access_in of access allowed any ip an extended list
11 extended access-list allow ip 10.250.1.0 255.255.255.0 any
outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1
mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool
NAT static NatExempt NatExempt of the source (indoor, outdoor)
NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3
NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search
!
network of the PAT_to_Outside_ClassA object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassB object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassC object
NAT dynamic interface (indoor, outdoor)
Access-group outside_access_in in interface outside
inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
dynamic-access-policy-registration DfltAccessPolicy
Sysopt connection timewait
Service resetoutside
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto-map dynamic dynmap 10 set pfs
Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1
life together - the association of security crypto dynamic-map dynmap 10 28800 seconds
Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000
Crypto-map dynamic dynmap 10 the value reverse-road
card crypto mymap 1 match address outside_1_cryptomap
card crypto mymap 1 set counterpart x.x.x.x
card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1
card crypto mymap 86400 seconds, 1 lifetime of security association set
map mymap 1 set security-association life crypto kilobytes 4608000
map mymap 100-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
crypto isakmp identity address
Crypto isakmp nat-traversal 30
Crypto ikev1 allow outside
IKEv1 crypto ipsec-over-tcp port 10000
IKEv1 crypto policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 50
preshared authentication
the Encryption
md5 hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
preshared authentication
aes-256 encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal BACKDOORVPN group policy
BACKDOORVPN group policy attributes
value of VPN-filter 11
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelall
BH.UK value by default-field
type tunnel-group BACKDOORVPN remote access
attributes global-tunnel-group BACKDOORVPN
address pool Admin_Pool
Group Policy - by default-BACKDOORVPN
IPSec-attributes tunnel-group BACKDOORVPN
IKEv1 pre-shared-key *.
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
Excellent.
Evaluate the useful ticket.
Thank you
Rizwan James
-
This seems to have started with the last batch of updates of Windows 7 (including SP1).
I can't connect using dial-up. Get the message:
Cannot load the Remote Access Connection Manager service
Error 711: The operation could not complete because it could not start the remote access connection manager service
in time. Please try the operation again.When I try to start the Remote Access Connection Manager service manually, I get the message:
Windows could not start the service on Local computer remote access connection manager.
20 error: the system cannot find the specified device.My phone displays the modem works properly, and telephony and the Secure Socket Tunneling Protocol service started.
I don't know what else might have changed.
Hello Vince_867,
Thanks for your post. Take a look at this thread for a possible solution to your problem.
See you soon
-
Remote VPN cannot access devices LAN or internet
So I have a server and a computer inside that I can access through an ASA 5505 with ASA 9.2 (1) and ASDM 7.2 (1)
The computer on 192.168.1.110 via port 8080 can show me a demo site.
The server on 192.168.1.222 got my DNS, HTTP, FTP, mail and more about it.
Outside, I got a computer (by outside, I hear from the firewall and the cable directly into the computer) on 192.168.20.2 and firewall outside being 192.168.20.1
From the outside I can access the 8080 without problem (and I guess as well with the server, but it is on another default gateway and are not accessible right now). -When I connect through my VPN I am assigned 192.168.30.5 but unable to connect inside the computer through 192.168.1.110:8080.
This will return the error: asymmetrical NAT rules matched for before and back flow; Connection for udp src outdoors: 192.168.30.5/49608 (...) dst inside: 192.168.1.222/53 refused because of the failure of the path reverse NAT.
Somewhere, I had a conflict or a non-created access rule. Anyone who wants to take a shot?
I marked with "BOLD" for what I thought that may be the cause.
ciscoasa (config) # sh running-config
: Saved
:
ASA Version 9.2 (1)
!
ciscoasa hostname
activate 8Ry2YjIyt7RRXU24 encrypted password
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
2KFQnbNIdI.2KYOU encrypted passwd
names of
192.168.30.5 mask - 192.168.30.200 local pool Pool of IP IP 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.254 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
address 192.168.20.1 255.255.255.0
!
boot system Disk0: / asa921 - k8.bin
passive FTP mode
permit same-security-traffic intra-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
object network testServer-8080
host 192.168.1.110
Description of the test server
network of the object server-21
Home 192.168.1.222
Description of the test server
network of the object Server-25
Home 192.168.1.222
Description of the test server
network of the object Server-53
Home 192.168.1.222
Description of the test server
network of the object server-80
Home 192.168.1.222
Description of the test server
network of the object server-443
Home 192.168.1.222
Description of the test server
network of the object server-2525
Home 192.168.1.222
Description of the test server
network of the object server-993
Home 192.168.1.222
Description of the test server
network of the object server-6001
Home 192.168.1.222
Description of the test server
network of the object server-6002
Home 192.168.1.222
Description of the test server
network of the object server-6003
Home 192.168.1.222
Description of the test server
network of the object server-6004
Home 192.168.1.222
Description of the test server
network of the VPN HOST object
192.168.30.0 subnet 255.255.255.0
network of the object inside
host 192.168.1.0
the vpn server object network
Home 192.168.1.222
outside_access_in list extended access permit tcp any object testServer-8080 eq 8080
outside_access_in list extended access permit tcp any object server-21 eq ftp
outside_access_in list extended access permit tcp any object Server-25 eq smtp
outside_access_in list extended access permit tcp any object server-2525 2525 eq
outside_access_in list extended access permit udp any object server-53 eq inactive field
outside_access_in list extended access permit tcp any object server-80 eq www
outside_access_in list extended access permit tcp any object server-443 https eq
outside_access_in list extended access permit tcp any object server-993 993 eq
outside_access_in list extended access permit tcp any object server-6001 eq 6001
outside_access_in list extended access permit tcp any object server-6002 6002 eq
outside_access_in list extended access permit tcp any object server-6003 eq 6003
outside_access_in list extended access permit tcp any object server-6004 eq 6004
outside_access_in to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.30.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 721.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) VPN-dynamic HOSTS within static destination to source Server VPN - vpn server
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
object network testServer-8080
NAT (inside, outside) interface static 8080 8080 tcp service
network of the object server-21
NAT static (inside, inside) of the service ftp ftp tcp interface
network of the object Server-25
NAT (inside, outside) interface static tcp smtp smtp service
network of the object Server-53
NAT static (inside, inside) interface tcp service area
network of the object server-80
NAT (inside, outside) interface static tcp www www service
network of the object server-443
NAT (inside, outside) interface static tcp https https service
network of the object server-2525
NAT (inside, outside) interface static 2525 2525 tcp service
network of the object server-993
NAT (inside, outside) interface static tcp 993 993 service
network of the object server-6001
NAT (inside, outside) interface static tcp 6001 6001 service
network of the object server-6002
NAT (inside, outside) interface static tcp 6002 6002 service
network of the object server-6003
NAT (inside, outside) interface static 6003 6003 tcp service
network of the object server-6004
NAT (inside, outside) interface static service tcp 6004 6004
Access-group outside_access_in in interface outside
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS AAA server HSS-auth-server protocol
allow only
AAA-server HSS-auth-server (inside) host 192.168.1.222
Timeout 5
key *.
identity of the user by default-domain LOCAL
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec pmtu aging infinite - the security association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
trustpool crypto ca policy
Crypto isakmp nat-traversal 30
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal HSSvpn group strategy
attributes of Group Policy HSSvpn
value of server DNS 192.168.1.222
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value outside_access_in ! This value was its own name earlier
HSS.dk value by default-field
type tunnel-group HSSvpn remote access
attributes global-tunnel-group HSSvpn
address IP-pool pool
HSS-auth-server authentication-server-group
Group Policy - by default-HSSvpn
password-management
IPSec-attributes tunnel-group HSSvpn
IKEv1 pre-shared-key *.
tunnel-group HSSvpn ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:9859258e11364180cf9b3e21173b3f2f
: endHello
"Nat" bold configuration is incorrect, as you would expect.
Replace it with something like this
the object of the LAN network
subnet 192.168.1.0 255.255.255.0NAT (inside, outside) 1 static source LAN LAN to static destination HOST-VPN-VPN-HOST
I also suggest using a separate access the ACL of the Tunnel from Split 'standard' list.
For example
standard SPLIT-TUNNEL access list permit 192.168.1.0 255.255.255.0
Naturally, you must pass the ACL above to used "group policy" .
In addition, if you want to control the incoming connections to VPN users in 'outside_access_in' ACL, then you could change the default settings on the SAA by running the command
No vpn sysopt connection permit
If you need to return back then just to deliver without 'no' in front. Then back to its default value. This does not show in the running configuration by the way.
With this setting all connections from VPN connections should be allowed on the interface ACL interface that ends the VPN connection. If in your case that would be the ACL attached to the 'outside' interface.
Hope this helps :)
-Jouni
-
Hello
I don't know what could be held, vpn users can ping to the outside and inside of the Cisco ASA interface but can not connect to servers or servers within the LAN ping.
is hell config please kindly and I would like to know what might happen.
hostname horse
domain evergreen.com
activate 2KFQnbNIdI.2KYOU encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
ins-guard
!
interface GigabitEthernet0/0
LAN description
nameif inside
security-level 100
192.168.200.1 IP address 255.255.255.0
!
interface GigabitEthernet0/1
Description CONNECTION_TO_FREEMAN
nameif outside
security-level 0
IP 196.1.1.1 255.255.255.248
!
interface GigabitEthernet0/2
Description CONNECTION_TO_TIGHTMAN
nameif backup
security-level 0
IP 197.1.1.1 255.255.255.248
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
boot system Disk0: / asa844-1 - k8.bin
boot system Disk0: / asa707 - k8.bin
passive FTP mode
clock timezone WAT 1
DNS server-group DefaultDNS
domain green.com
network of the NETWORK_OBJ_192.168.2.0_25 object
Subnet 192.168.2.0 255.255.255.128
network of the NETWORK_OBJ_192.168.202.0_24 object
192.168.202.0 subnet 255.255.255.0
network obj_any object
subnet 0.0.0.0 0.0.0.0
the DM_INLINE_NETWORK_1 object-group network
object-network 192.168.200.0 255.255.255.0
object-network 192.168.202.0 255.255.255.0
the DM_INLINE_NETWORK_2 object-group network
object-network 192.168.200.0 255.255.255.0
object-network 192.168.202.0 255.255.255.0
access-list extended INSIDE_OUT allow ip 192.168.202.0 255.255.255.0 any
access-list extended INSIDE_OUT allow ip 192.168.200.0 255.255.255.0 any
Access extensive list permits all ip a OUTSIDE_IN
gbnlvpntunnel_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0
standard access list gbnlvpntunnel_splitTunnelAcl allow 192.168.202.0 255.255.255.0
gbnlvpntunnell_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0
standard access list gbnlvpntunnell_splitTunnelAcl allow 192.168.202.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
backup of MTU 1500
mask of local pool VPNPOOL 192.168.2.0 - 192.168.2.100 IP 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm-645 - 206.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
NAT (inside, backup) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
NAT (inside, outside) static source DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
NAT (inside, backup) static source DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
!
network obj_any object
dynamic NAT interface (inside, backup)
Access-group interface inside INSIDE_OUT
Access-group OUTSIDE_IN in interface outside
Route outside 0.0.0.0 0.0.0.0 196.1.1.2 1 track 10
Route outside 0.0.0.0 0.0.0.0 197.1.1.2 254
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
Enable http server
http 192.168.200.0 255.255.255.0 inside
http 192.168.202.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
monitor SLA 100
type echo protocol ipIcmpEcho 212.58.244.71 interface outside
Timeout 3000
frequency 5
monitor als 100 calendar life never start-time now
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
backup_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
backup of crypto backup_map interface card
Crypto ikev1 allow outside
Crypto ikev1 enable backup
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
!
track 10 rtr 100 accessibility
Telnet 192.168.200.0 255.255.255.0 inside
Telnet 192.168.202.0 255.255.255.0 inside
Telnet timeout 5
SSH 192.168.202.0 255.255.255.0 inside
SSH 192.168.200.0 255.255.255.0 inside
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 15
SSH group dh-Group1-sha1 key exchange
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal group vpntunnel strategy
Group vpntunnel policy attributes
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpntunnel_splitTunnelAcl
field default value green.com
internal vpntunnell group policy
attributes of the strategy of group vpntunnell
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list gbnlvpntunnell_splitTunnelAcl
field default value green.com
Green user name encrypted BoEFKkDtbnX5Uy1Q privilege 15 password
attributes of user name THE
VPN-group-policy gbnlvpn
tunnel-group vpntunnel type remote access
tunnel-group vpntunnel General attributes
address VPNPOOL pool
strategy-group-by default vpntunnel
tunnel-group vpntunnel ipsec-attributes
IKEv1 pre-shared-key *.
type tunnel-group vpntunnell remote access
tunnel-group vpntunnell General-attributes
address VPNPOOL2 pool
Group Policy - by default-vpntunnell
vpntunnell group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:7c1b1373bf2e2c56289b51b8dccaa565
Hello
1 - Please run these commands:
"crypto isakmp nat-traversal 30.
"crypto than dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 Road opposite value.
The main issue here is that you have two roads floating and outside it has a better than backup metric, that's why I added the command 'reverse-road '.
Please let me know.
Thank you.
-
Remote access VPN with ASA 5510 by using the DHCP server
Hello
Can someone please share your knowledge to help me find out why I'm not able to receive an IP address on the remote access VPN connection so that I can get an IP local pool DHCP?
I'm trying to set up remote access VPN with ASA 5510. It works with dhcp local pool but does not seem to work when I tried to use an existing DHCP server. It is tested in an internal network as follows:
!
ASA Version 8.2 (5)
!
interface Ethernet0/1
nameif inside
security-level 100
IP 10.6.0.12 255.255.254.0
!
IP local pool testpool 10.6.240.150 - 10.6.240.159 a mask of 255.255.248.0. (worked with it)
!
Route inside 0.0.0.0 0.0.0.0 10.6.0.1 1
!
Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dyn1 1jeu transform-set FirstSet
dynamic mymap 1 dyn1 ipsec-isakmp crypto map
mymap map crypto inside interface
crypto ISAKMP allow inside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
!
VPN-addr-assign aaa
VPN-addr-assign dhcp
!
internal group testgroup strategy
testgroup group policy attributes
DHCP-network-scope 10.6.192.1
enable IPSec-udp
IPSec-udp-port 10000
!
username testlay password * encrypted
!
tunnel-group testgroup type remote access
tunnel-group testgroup General attributes
strategy-group-by default testgroup
DHCP-server 10.6.20.3
testgroup group tunnel ipsec-attributes
pre-shared key *.
!
I got following output when I test connect to the ASA with Cisco VPN client 5.0
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: (4) SA (1) + KE + NUNCIO (10) + ID (5), HDR + VENDO
4024 bytesR copied in 3,41 0 seconds (1341 by(tes/sec) 13) of the SELLER (13) seller (13) + the SELLER (13), as well as the SELLER (13) ++ (0) NONE total length: 853
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ISA_KE
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, nonce payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received xauth V6 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, DPD received VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received Fragmentation VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received NAT-Traversal worm 02 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, connection landed on tunnel_group testgroup
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA proposal # 1, turn # 9 entry overall IKE acceptable matches # 1
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build the payloads of ISAKMP security
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building nonce payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for answering machine...
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of payload ID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of Cisco Unity VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing payload V6 VID xauth
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building dpd vid payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing the payload of the NAT-Traversal VID ver 02
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of Fragmentation VID + load useful functionality
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, send Altiga/Cisco VPN3000/Cisco ASA GW VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR SA (1) KE (4) NUNCIO (10) + ID (5) + HASH (8) + SELLER (13) + the SELLER (13) + the SELLER (13) + the SELLER (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) total length: 440
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + HASH (8) + NOTIFY (11) + NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) overall length: 168
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, useful treatment IOS/PIX Vendor ID (version: 1.0.0 capabilities: 00000408)
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: Group = testgroup, I
[OK]
KenS-mgmt-012 # P = 10.15.200.108, status of automatic NAT detection: remote end is NOT behind a NAT device this end is NOT behind a NAT device
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 72
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 87
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, transformation MODE_CFG response attributes.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized primary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized secondary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Compression IP = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling political = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: setting Proxy browser = no - modify
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: browser Local Proxy bypass = disable
Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, (testlay) the authenticated user.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 64
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + NONE (0) overall length: 60
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cfg ACK processing attributes
Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 49ae1bb8) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 182
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, treatment cfg request attributes
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 address!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 network mask!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for DNS server address.
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the address of the WINS server.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, transaction mode attribute unhandled received: 5
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the banner!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting save PW!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: receipt of request for default domain name!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for Split-Tunnel list!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for split DNS!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for PFS setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Proxy Client browser setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the list of backup peer ip - sec!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting disconnect from the Client Smartcard Removal!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Version of the Application.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Type of Client: Windows NT Client Application Version: 5.0.07.0440
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for FWTYPE!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: request received for the DHCP for DDNS hostname is: DEC20128!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the UDP Port!
Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = b04e830f) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE has received the response from type [] at the request of the utility of IP address
Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cannot get an IP address for the remote peer
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE TM V6 WSF (struct & 0xd8030048)
, : TM_DONE, EV_ERROR--> TM_BLD_REPLY, EV_IP_FAIL--> TM_BLD_REPLY NullEvent--> TM_BLD_REPLY, EV_GET_IP--> TM_BLD_REPLY, EV_NEED_IP--> TM_WAIT_REQ, EV_PROC_MSG--> TM_WAIT_REQ, EV_HASH_OK--> TM_WAIT_REQ, NullEvent Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE AM Responder WSF (struct & 0xd82b6740)
, : AM_DONE, EV_ERROR--> AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL--> AM_TM_INIT_MODECFG_V6H NullEvent--> AM_TM_INIT_MODECFG, EV_WAIT--> AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG--> AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK--> AM_TM_INIT_XAUTH_V6H NullEvent--> AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b ending: 0x0945c001, refcnt flags 0, tuncnt 0
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending clear/delete with the message of reason
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing the payload to delete IKE
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 9de30522) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80
Kind regards
Lay
For the RADIUS, you need a definition of server-aaa:
Protocol AAA - NPS RADIUS server RADIUS
AAA-server RADIUS NPS (inside) host 10.10.18.12
key *.
authentication port 1812
accounting-port 1813
and tell your tunnel-group for this server:
General-attributes of VPN Tunnel-group
Group-NPS LOCAL RADIUS authentication server
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
remote access VPN not connected - no access inside
Hi, I have successfully configured remote access VPN router, it is connected, but no access to the inside, none of my ip addresses. I do not know SPLIT_ACL is ok and I've denied NATting them. For me, everything is ok. I did a lot in ASA, without anyproblem. Thanks for the comments.
enable secret 5 $1$ y0AJ$ rhrjbrpe5NDiAyHGlfeNi.
!
AAA new-model
!
!
AAA authentication login bcc_users local
AAA authorization bcc_group LAN
!
crypto ISAKMP policy 10
BA aes
preshared authentication
Group 2
!
ISAKMP crypto client configuration group ra_vpn_bcc
key *.
DNS 8.8.8.8
bcc.local field
pool vpn_pool
ACL SPLIT_ACL
Max-users 7
netmask 255.255.255.0
!
!
Crypto ipsec transform-set RIGHT aes - esp esp-sha-hmac
tunnel mode
!
!
!
Crypto-map dynamic dynmap 10
Set transform-set RIGHT
market arriere-route
!
!
card crypto client CRYPTO_VPN of authentication list bcc_users
card crypto isakmp authorization list bcc_group CRYPTO_VPN
crypto card for the CRYPTO_VPN client configuration address respond
map CRYPTO_VPN 10-isakmp ipsec crypto dynamic dynmap
!
!
interface GigabitEthernet0/0/4
IP address %.
NAT outside IP
auto negotiation
BFD interval 50 50 5 min_rx multiplier
card crypto CRYPTO_VPN
!
!
IP local pool vpn_pool 172.31.255.0 172.31.255.250
NAT extended IP access list
deny ip 10.0.0.0 0.255.255.255 172.31.255.0 0.0.0.255
deny ip 172.16.0.0 0.0.255.255 172.31.255.0 0.0.0.255
deny ip 192.168.0.0 0.0.255.255 172.31.255.0 0.0.0.255
IP address 172.16.0.0 allow 0.15.255.255 all
IP 192.168.0.0 allow 0.0.255.255 everything
IP 10.0.0.0 allow 0.255.255.255 everything
SPLIT_ACL extended IP access list
IP 10.0.0.0 allow 0.255.255.255 172.31.255.0 0.0.0.255
IP address 172.16.0.0 allow 0.0.255.255 172.31.255.0 0.0.0.255
IP 192.168.0.0 allow 0.0.255.255 172.31.255.0 0.0.0.255
Take a look at the delivery.
You do not have a route to the VPN pool on a nearby device.
-
How many group Supportepar ASA 5520 vpn for remote access
Hello
Howmany vpn group is supported on asa 5520 with configuraion vpn remote access.
Concerning
1 if nat-control is disabled and you do not have any other order NAT in your config file, you do not have it. Try to remove the existing "NAT 0" command and "clear xlate."
2. you must ensure that your network inside know they can go by ASA to access remote vpn client IP. You have any device layer 3 behind the ASA that does the routing. If so, please verify that this is the routing table.
-
Hi all
I read the http://www.cisco.com/en/US/docs/security/asa/asa80/getting_started/asa5505/quick/guide/rem_acc.html and following the steps to create a remote access VPN. At the end of this post is delivered to the FW config.
I test the connection on a Cisco VPN Client for Windows Remote with plans on the migration of the profile to my Linux laptop. What I see is an error message when you run 'debug cryptop isa 129' of
Dec 09 10:10:03 [IKEv1]: Group = DefaultRAGroup, IP = 83.109.134.21, Removing peer to peer table does not, no match!
Dec 09 10:10:03 [IKEv1]: Group = DefaultRAGroup, IP = 83.109.134.21, error: cannot delete PeerTblEntryWhat seems strange to me, is that I have a group policy and a configured connection IPSec 'RemoteHome' profile, but it is not referenced in the debug output. I searched through my config for DefaultRAGroup, but nothing helped. However I found it in the ASDM under IPSec connection profiles.
I configured the FW to use LOCAL authentication and have configured the VPN Client with the right user name and password.
So, basically, I'm at a loss on how to correct my mistake. Any help much appreciated.
After the config FW is the power output of debug crypto isa 129.
See you soon,.
Conor
RemoteHome_splitTunnelAcl list standard access allowed host 10.2.2.2
RemoteHome_splitTunnelAcl list standard access allowed 172.16.0.0 255.255.0.0
RemoteHome_splitTunnelAcl standard access list allow 10.3.3.0 255.255.255.0
RemoteHome_splitTunnelAcl list standard access allowed 192.168.2.0 255.255.255.0
access-list 1 permit line INSIDE_nat0_outbound extended ip host 10.2.2.2 192.168.2.64 255.255.255.192
allowed to Access - list INSIDE_nat0_outbound line 2 extended ip 172.16.0.0 255.255.0.0 192.168.2.64 255.255.255.192
permit for access list 3 INSIDE_nat0_outbound line scope ip 10.3.3.0 255.255.255.0 192.168.2.64 255.255.255.192
allowed to Access - list INSIDE_nat0_outbound line 4 extended ip 192.168.2.0 255.255.255.0 192.168.2.64 255.255.255.192
local pool VPN_REMOTE_POOL 192.168.2.90 - 192.168.2.99 255.255.255.0 IP mask
internal RemoteHome group strategy
Group Policy attributes RemoteHome
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list RemoteHome_splitTunnelAcl
value of DNS server *.
cunningtek.com value by default-field
tunnel-group RemoteHome type remote access
attributes global-tunnel-group RemoteHome
Group Policy - by default-RemoteHome
address VPN_REMOTE_POOL pool
IPSec-attributes tunnel-group RemoteHome
pre-shared key *.
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
NAT (INSIDE) 0 access-list INSIDE_nat0_outbound tcp udp 0 0 0Firewall # Dec 09 10:10:03 [IKEv1]: IP = 83.109.134.21, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR (4) SA (1) + KE + NUNCIO (10) + ID (5) the SELLER (13) + the SELLER (13) + SOLD
OR (13) of the SELLER (13) + the SELLER (13) + (0) NONE total length: 849
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, SA payload processing
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, processing ke payload
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, payload processing ISA_KE
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, nonce payload processing
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, payload processing ID
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, payload processing VID
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, received xauth V6 VID
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, payload processing VID
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, DPD received VID
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, payload processing VID
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, received Fragmentation VID
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, payload processing VID
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, received NAT-Traversal worm 02 VID
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, payload processing VID
Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, the customer has received Cisco Unity VID
Dec 09 10:10:03 [IKEv1]: IP = 83.109.134.21, message received ISAKMP Aggressive Mode 1 with the name of Group of unknown tunnel "conor".
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, IKE SA payload processing
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, IKE SA proposal # 1, transform # 5 entry overall IKE acceptable matches # 1
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, build the payloads of ISAKMP security
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, building ke payload
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, building nonce payload
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, Generating keys for answering machine...
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, construction of payload ID
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, build payloads of hash
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, calculation of hash for ISAKMP
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, build payloads of Cisco Unity VID
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, constructing payload V6 VID xauth
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, constructing the payload of the NAT-Traversal VID ver 02
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, NAT-discovery payload construction
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, NAT discovery hash calculation
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, NAT-discovery payload construction
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, NAT discovery hash calculation
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, construction of Fragmentation VID + load useful functionality
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, build payloads VID
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, Send Altiga/Cisco VPN3000/Cisco ASA GW VID
Dec 09 10:10:03 [IKEv1]: IP = 83.109.134.21, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR (4) SA (1) + KE + NUNCIO (10) + ID (5) + HASH (8) the SELLER (13) + the SELLER (13) + SOLD
OR (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + (0) NONE total length: 424
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, case of mistaken IKE AM Responder WSF (struct & 0xd8d3bed8), : AM_DONE, EV_ERROR--> AM_SND_MSG2, EV_
SND_MSG--> AM_SND_MSG2, EV_START_TMR--> AM_BLD_MSG2, EV_BLD_MSG2_TRL--> AM_BLD_MSG2, EV_SKEYID_OK--> AM_BLD_MSG2, NullEvent--> AM_BLD_MSG2, EV_GEN_SKEYID--> AM_BLD_MSG2, EV_BLD_MSG2_HDR
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, IKE SA AM:7ff48db9 ending: 0x0104c001, refcnt flags 0, tuncnt 0
Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, sending clear/delete with the message of reason
Dec 09 10:10:03 [IKEv1]: Group = DefaultRAGroup, IP = 83.109.134.21, Removing peer to peer table does not, no match!
Dec 09 10:10:03 [IKEv1]: Group = DefaultRAGroup, IP = 83.109.134.21, error: cannot delete PeerTblEntryI think this is the beginning of your question.
Message received ISAKMP aggressive Mode 1 with the name of the unknown group tunnel "conor".
In the vpn client, you must enter the name of the group, RemoteHome and pre shared key, NOT your username. You will be asked your username after login.
As the name conor group does not exist, it is failing in the DefaultRAGroup
-
Problem with ASA 5505 VPN remote access
After about 1 year to have the VPN Client from Cisco connection to an ASA 5505 with no problems, all of a sudden one day it stops working. The customer is able to get a connection to the ASA and browse the local network for only about 30 seconds after the connection. After that, no access is available to the network behind the ASA. I have tried everything I can think of to try to solve the problem, but at this point, I'm just banging my head against a wall. Anyone know what could cause this?
Here is the cfg running of the ASA
----------------------------------------------------------------------------------------
: Saved
:
ASA Version 8.4 (1)
!
hostname NCHCO
enable encrypted password xxxxxxxxxxxxxxx
xxxxxxxxxxx encrypted passwd
names of
description of NCHCO name 192.168.2.0 City offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.2.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address **. ***. 255.255.255.248
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
boot system Disk0: / asa841 - k8.bin
passive FTP mode
network of the NCHCO object
Subnet 192.168.2.0 255.255.255.0
network object obj - 192.168.1.0
subnet 192.168.1.0 255.255.255.0
network object obj - 192.168.2.64
subnet 192.168.2.64 255.255.255.224
network object obj - 0.0.0.0
subnet 0.0.0.0 255.255.255.0
network obj_any object
subnet 0.0.0.0 0.0.0.0
the Web server object network
the FINX object network
Home 192.168.2.11
rdp service object
source between 1-65535 destination eq 3389 tcp service
Rdp description
outside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
outside_nat0_outbound extended access list permit ip object NCHCO 192.168.2.0 255.255.255.0
inside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access all 192.168.2.64 255.255.255.224
permit access list extended ip 0.0.0.0 inside_nat0_outbound 255.255.255.0 192.168.2.64 255.255.255.224
outside_1_cryptomap extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
outside_1_cryptomap_1 extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0
LAN_Access list standard access allowed 192.168.2.0 255.255.255.0
LAN_Access list standard access allowed 0.0.0.0 255.255.255.0
NCHCO_splitTunnelAcl_1 list standard access allowed 192.168.2.0 255.255.255.0
AnyConnect_Client_Local_Print deny ip extended access list a whole
AnyConnect_Client_Local_Print list extended access permit tcp any any eq lpd
Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 631
print the access-list AnyConnect_Client_Local_Print Note Windows port
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol
AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.251 eq 5353
AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol
AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.252 eq 5355
Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print
AnyConnect_Client_Local_Print list extended access permit tcp any any eq 137
AnyConnect_Client_Local_Print list extended access udp allowed any any eq netbios-ns
outside_access_in list extended access permit tcp any object FINX eq 3389
outside_access_in_1 list extended access allowed object rdp any object FINX
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask of VPN_Pool VPN_Start VPN_End of local pool IP 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 649.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, all) static source NCHCO destination NCHCO static obj - 192.168.1.0 obj - 192.168.1.0
NAT (inside, all) static source any any destination static obj - 192.168.2.64 obj - 192.168.2.64
NAT (inside, all) source static obj - 0.0.0.0 0.0.0.0 - obj destination static obj - 192.168.2.64 obj - 192.168.2.64
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
the FINX object network
NAT (inside, outside) interface static service tcp 3389 3389
Access-group outside_access_in_1 in interface outside
Route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
network-acl outside_nat0_outbound
WebVPN
SVC request to enable default svc
Enable http server
http 192.168.1.0 255.255.255.0 inside
http *. **. ***. 255.255.255.255 outside
http *. **. ***. 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac ikev1 l2tp-transform
IKEv1 crypto ipsec transform-set l2tp-transformation mode transit
Crypto ipsec transform-set vpn-transform ikev1 esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA ikev1
transport mode encryption ipsec transform-set TRANS_ESP_3DES_SHA ikev1
Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5 ikev1
transport mode encryption ipsec transform-set TRANS_ESP_3DES_MD5 ikev1
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs Group1
crypto dynamic-map dyn-map 10 set transform-set l2tp vpn-transform processing ikev1
dynamic-map encryption dyn-map 10 value reverse-road
Crypto-map dynamic outside_dyn_map 20 set transform-set ESP-3DES-SHA ikev1
Crypto-map dynamic outside_dyn_map 20 the value reverse-road
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs Group1
peer set card crypto outside_map 1 74.219.208.50
card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1
map outside_map 20-isakmp ipsec crypto dynamic outside_dyn_map
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside crypto map inside_map interface
card crypto vpn-map 1 match address outside_1_cryptomap_1
card crypto vpn-card 1 set pfs Group1
set vpn-card crypto map peer 1 74.219.208.50
card crypto 1 set transform-set ESP-3DES-SHA ikev1 vpn-map
dynamic vpn-map 10 dyn-map ipsec isakmp crypto map
crypto isakmp identity address
Crypto ikev1 allow inside
Crypto ikev1 allow outside
IKEv1 crypto ipsec-over-tcp port 10000
IKEv1 crypto policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
IKEv1 crypto policy 15
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 35
preshared authentication
3des encryption
sha hash
Group 2
life 86400
enable client-implementation to date
Telnet 192.168.1.0 255.255.255.0 inside
Telnet NCHCO 255.255.255.0 inside
Telnet timeout 5
SSH 192.168.1.0 255.255.255.0 inside
SSH NCHCO 255.255.255.0 inside
SSH timeout 5
Console timeout 0
dhcpd address 192.168.2.150 - 192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
lease interface 64000 dhcpd inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal DefaultRAGroup group strategy
attributes of Group Policy DefaultRAGroup
value of server DNS 192.168.2.1
L2TP ipsec VPN-tunnel-Protocol ikev1
nchco.local value by default-field
attributes of Group Policy DfltGrpPolicy
value of server DNS 192.168.2.1
L2TP ipsec VPN-tunnel-Protocol ikev1 ssl-clientless ssl-client
allow password-storage
enable IPSec-udp
enable dhcp Intercept 255.255.255.0
the address value VPN_Pool pools
internal NCHCO group policy
NCHCO group policy attributes
value of 192.168.2.1 DNS Server 8.8.8.8
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list NCHCO_splitTunnelAcl_1
value by default-field NCHCO.local
admin LbMiJuAJjDaFb2uw encrypted privilege 15 password username
username privilege 15 encrypted password yB1lHEVmHZGj5C2Z 8njferg
username NCHvpn99 password dhn. JzttvRmMbHsP encrypted
attributes global-tunnel-group DefaultRAGroup
address (inside) VPN_Pool pool
address pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside LOCAL)
LOCAL authority-server-group
authorization-server-group (inside) LOCAL
authorization-server-group (outside LOCAL)
Group Policy - by default-DefaultRAGroup
band-Kingdom
band-band
IPSec-attributes tunnel-group DefaultRAGroup
IKEv1 pre-shared-key *.
NOCHECK Peer-id-validate
tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
tunnel-group DefaultWEBVPNGroup ppp-attributes
PAP Authentication
ms-chap-v2 authentication
tunnel-group 74.219.208.50 type ipsec-l2l
IPSec-attributes tunnel-group 74.219.208.50
IKEv1 pre-shared-key *.
type tunnel-group NCHCO remote access
attributes global-tunnel-group NCHCO
address pool VPN_Pool
Group Policy - by default-NCHCO
IPSec-attributes tunnel-group NCHCO
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:a2110206e1af06974c858fb40c6de2fc
: end
ASDM image disk0: / asdm - 649.bin
ASDM VPN_Start 255.255.255.255 inside location
ASDM VPN_End 255.255.255.255 inside location
don't allow no asdm history
---------------------------------------------------------------------------------------------------------------
And here are the logs of the Cisco VPN Client when sailing, then is unable to browse the network behind the ASA:
---------------------------------------------------------------------------------------------------------------
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.
Customer type: Windows, Windows NT
Running: 6.1.7601 Service Pack 1
Config files directory: C:\Program Files (x 86) \Cisco Systems\VPN Client\
1 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600026
Try to find a certificate using hash Serial.
2 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600027
Found a certificate using hash Serial.
3 09:44:55.693 01/10/13 Sev = Info/6 GUI/0x63B00011
RELOADED successfully certificates in all certificate stores.
4 09:45:02.802 10/01/13 Sev = Info/4 CM / 0 x 63100002
Start the login process
5 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100004
Establish a secure connection
6 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100024
Attempt to connect with the server "*." **. ***. *** »
7 09:45:02.802 10/01/13 Sev = Info/6 IKE/0x6300003B
Try to establish a connection with *. **. ***. ***.
8 09:45:02.818 10/01/13 Sev = Info/4 IKE / 0 x 63000001
From IKE Phase 1 negotiation
9 09:45:02.865 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) to *. **. ***. ***
10 09:45:02.896 10/01/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
11 09:45:02.896 10/01/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">
12 09:45:02.896 10/01/13 Sev = Info/5 IKE / 0 x 63000001
Peer is a compatible peer Cisco-Unity
13 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports XAUTH
14 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports the DPD
15 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports NAT - T
16 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001
Peer supports fragmentation IKE payloads
17 09:45:02.927 01/10/13 Sev = Info/6 IKE / 0 x 63000001
IOS Vendor ID successful construction
18 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) to *. **. ***. ***
19 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000083
IKE port in use - Local Port = 0xDD3B, Remote Port = 0x01F4
20 09:45:02.927 01/10/13 Sev = Info/5 IKE / 0 x 63000072
Automatic NAT detection status:
Remote endpoint is NOT behind a NAT device
This effect is NOT behind a NAT device
21 09:45:02.927 01/10/13 Sev = Info/4 CM/0x6310000E
ITS established Phase 1. 1 crypto IKE Active SA, 0 IKE SA authenticated user in the system
22 09:45:02.943 10/01/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
23 09:45:02.943 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
24 09:45:02.943 01/10/13 Sev = Info/4 CM / 0 x 63100015
Launch application xAuth
25 09:45:03.037 01/10/13 Sev = Info/6 GUI/0x63B00012
Attributes of the authentication request is 6: 00.
26 09:45:03.037 01/10/13 Sev = Info/4 CM / 0 x 63100017
xAuth application returned
27 09:45:03.037 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
28 09:45:03.037 10/01/13 Sev = Info/4 IPSEC / 0 x 63700008
IPSec driver started successfully
29 09:45:03.037 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
30 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
31 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
32 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
33 09:45:03.083 01/10/13 Sev = Info/4 CM/0x6310000E
ITS established Phase 1. 1 crypto IKE Active SA, 1 IKE SA authenticated user in the system
34 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300005E
Customer address a request from firewall to hub
35 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
36 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
37 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="" **.**.***.***="" isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
38 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 192.168.2.70
39 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.255.0
40 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 192.168.2.1
41 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 8.8.8.8
42 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000001
43 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
44 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000F
SPLIT_NET #1
= 192.168.2.0 subnet
mask = 255.255.255.0
Protocol = 0
SRC port = 0
port dest = 0
45 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = NCHCO.local
46 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_UDP_NAT_PORT, value = 0 x 00002710
47 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000
48 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = 8.4 (1) Cisco systems, Inc. ASA5505 Version built by manufacturers on Tuesday, January 31, 11 02:11
49 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001
50 09:45:03.146 01/10/13 Sev = Info/4 CM / 0 x 63100019
Data in mode Config received
51 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000056
Received a request from key driver: local IP = 192.168.2.70, GW IP = *. **. ***. remote IP address = 0.0.0.0
52 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK QM * (HASH, SA, NO, ID, ID) to *. **. ***. ***
53 09:45:03.177 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
54 09:45:03.177 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">
55 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000045
Answering MACHINE-LIFE notify has value of 86400 seconds
56 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000047
This SA was already alive for 1 second, expiration of adjustment to 86399 seconds now
57 09:45:03.193 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
58 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" qm="" *(hash,="" sa,="" non,="" id,="" id,="" notify:status_resp_lifetime)="" from="">
59 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000045
Answering MACHINE-LIFE notify is set to 28800 seconds
60 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK QM * (HASH) to *. **. ***. ***
61 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000059
IPsec Security Association of loading (MsgID = SPI OUTBOUND SPI INCOMING = 0x3EBEBFC5 0xAAAF4C1C = 967A3C93)
62 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000025
OUTGOING ESP SPI support: 0xAAAF4C1C
63 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000026
Charges INBOUND ESP SPI: 0x3EBEBFC5
64 09:45:03.193 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
65 09:45:03.521 01/10/13 Sev = Info/6 CVPND / 0 x 63400001
Launch VAInst64 for controlling IPSec virtual card
66 09:45:03.896 01/10/13 Sev = Info/4 CM / 0 x 63100034
The virtual card has been activated:
IP=192.168.2.70/255.255.255.0
DNS = 192.168.2.1, 8.8.8.8
WINS = 0.0.0.0 0.0.0.0
Domain = NCHCO.local
Split = DNS names
67 09:45:03.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 261
68 09:45:07.912 01/10/13 Sev = Info/4 CM / 0 x 63100038
Were saved successfully road to file changes.
69 09:45:07.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013
Destination mask subnet Gateway Interface metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
**. **. ***. 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 261
192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 261
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 261
70 09:45:07.912 01/10/13 Sev = Info/6 CM / 0 x 63100036
The routing table has been updated for the virtual card
71 09:45:07.912 01/10/13 Sev = Info/4 CM/0x6310001A
A secure connection established
72 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B
Look at address added to 96.11.251.149. Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.
73 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B
Look at address added to 192.168.2.70. Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.
74 09:45:07.943 01/10/13 Sev = Info/5 CM / 0 x 63100001
Did not find the smart card to watch for removal
75 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
76 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010
Creates a new key structure
77 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F
Adding key with SPI = 0x1c4cafaa in the list of keys
78 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010
Creates a new key structure
79 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F
Adding key with SPI = 0xc5bfbe3e in the list of keys
80 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370002F
Assigned WILL interface private addr 192.168.2.70
81 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700037
Configure the public interface: 96.11.251.149. SG: **.**.***.***
82 09:45:07.943 10/01/13 Sev = Info/6 CM / 0 x 63100046
Define indicator tunnel set up in the registry to 1.
83 09:45:13.459 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
84 09:45:13.459 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205276
85 09:45:13.474 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
86 09:45:13.474 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
87 09:45:13.474 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205276, seq # expected is 107205276
88 09:45:15.959 01/10/13 Sev = Info/4 IPSEC / 0 x 63700019
Activate key dating SPI = 0x1c4cafaa key with SPI = 0xc5bfbe3e
89 09:46:00.947 10/01/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
90 09:46:00.947 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205277
91 09:46:01.529 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
92 09:46:01.529 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
93 09:46:01.529 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205277, seq # expected is 107205277
94 09:46:11.952 01/10/13 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***
95 09:46:11.952 01/10/13 Sev = Info/6 IKE/0x6300003D
Upon request of the DPD to *. **. ***. , our seq # = 107205278
96 09:46:11.979 01/10/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
97 09:46:11.979 01/10/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">
98 09:46:11.979 01/10/13 Sev = Info/5 IKE / 0 x 63000040
Receipt of DPO ACK to *. **. ***. seq # receipt = 107205278, seq # expected is 107205278
---------------------------------------------------------------------------------------------------------------
Any help would be appreciated, thanks!
try to refuse the ACL (access-list AnyConnect_Client_Local_Print extended deny ip any one) at the end of the ACL.
-
Problem with remote access VPN on ASA 5505
I currently have a problem of an ASA 5505 configuration to connect via VPN remote access by using the Cisco VPN Client 5.0.07.0440 under Windows 8 Pro x 64. The VPN client will prompt you for the user name and password during the connection process, but fails soon after.
The VPN client connects is as follows:
---------------------------------------------------------------------------------------------------------------------------------------
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.
Customer type: Windows, Windows NT
Running: 6.2.9200
2 15:09:21.240 11/12/12 Sev = Info/4 CM / 0 x 63100002
Start the login process
3 15:09:21.287 11/12/12 Sev = Info/4 CM / 0 x 63100004
Establish a secure connection
4 15:09:21.287 11/12/12 Sev = Info/4 CM / 0 x 63100024
Attempt to connect with the server "*." **. ***. *** »
5 15:09:21.287 11/12/12 Sev = Info/6 IKE/0x6300003B
Try to establish a connection with *. **. ***. ***.
6 15:09:21.287 11/12/12 Sev = Info/4 IKE / 0 x 63000001
From IKE Phase 1 negotiation
7 15:09:21.303 11/12/12 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) to *. **. ***. ***
8 15:09:21.365 11/12/12 Sev = Info/6 GUI/0x63B00012
Attributes of the authentication request is 6: 00.
9 15:09:21.334 11/12/12 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
10 15:09:21.334 11/12/12 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">
11 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001
Peer is a compatible peer Cisco-Unity
12 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001
Peer supports XAUTH
13 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001
Peer supports the DPD
14 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001
Peer supports NAT - T
15 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001
Peer supports fragmentation IKE payloads
16 15:09:21.334 11/12/12 Sev = Info/6 IKE / 0 x 63000001
IOS Vendor ID successful construction
17 15:09:21.334 11/12/12 Sev = Info/4 IKE / 0 x 63000013
SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) to *. **. ***. ***
18 15:09:21.334 11/12/12 Sev = Info/6 IKE / 0 x 63000055
Sent a keepalive on the IPSec Security Association
19 15:09:21.334 11/12/12 Sev = Info/4 IKE / 0 x 63000083
IKE port in use - Local Port = 0xFBCE, Remote Port = 0 x 1194
20 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000072
Automatic NAT detection status:
Remote endpoint is NOT behind a NAT device
This effect is behind a NAT device
21 15:09:21.334 11/12/12 Sev = Info/4 CM/0x6310000E
ITS established Phase 1. 1 crypto IKE Active SA, 0 IKE SA authenticated user in the system
22 15:09:21.365 11/12/12 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
23 15:09:21.365 11/12/12 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
24 15:09:21.365 11/12/12 Sev = Info/4 CM / 0 x 63100015
Launch application xAuth
25 15:09:21.474 11/12/12 Sev = Info/4 IPSEC / 0 x 63700008
IPSec driver started successfully
26 15:09:21.474 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
27 15:09:27.319 11/12/12 Sev = Info/4 CM / 0 x 63100017
xAuth application returned
28 15:09:27.319 11/12/12 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
29 15:09:27.365 11/12/12 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
30 15:09:27.365 11/12/12 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
31 15:09:27.365 11/12/12 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
32 15:09:27.365 11/12/12 Sev = Info/4 CM/0x6310000E
ITS established Phase 1. 1 crypto IKE Active SA, 1 IKE SA authenticated user in the system
33 15:09:27.365 11/12/12 Sev = Info/5 IKE/0x6300005E
Customer address a request from firewall to hub
34 15:09:27.365 11/12/12 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***
35 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
36 15:09:27.397 11/12/12 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">
37 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 192.168.2.70
38 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.255.0
39 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 192.168.2.1
40 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 8.8.8.8
41 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000001
42 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = NCHCO
43 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000
44 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc. ASA5505 Version 8.2 (5) built by manufacturers on Saturday, May 20, 11 16:00
45 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001
46 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = received and by using the NAT - T port number, value = 0 x 00001194
47 15:09:27.397 11/12/12 Sev = Info/4 CM / 0 x 63100019
Data in mode Config received
48 15:09:27.412 11/12/12 Sev = Info/4 IKE / 0 x 63000056
Received a request from key driver: local IP = 192.168.2.70, GW IP = *. **. ***. remote IP address = 0.0.0.0
49 15:09:27.412 11/12/12 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK QM * (HASH, SA, NO, ID, ID) to *. **. ***. ***
50 15:09:27.444 11/12/12 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
51 15:09:27.444 11/12/12 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">
52 15:09:27.444 11/12/12 Sev = Info/5 IKE / 0 x 63000045
Answering MACHINE-LIFE notify has value of 86400 seconds
53 15:09:27.444 11/12/12 Sev = Info/5 IKE / 0 x 63000047
This SA was already alive for 6 seconds, setting expiration 86394 seconds now
54 15:09:27.459 11/12/12 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
55 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:no_proposal_chosen)="" from="">
56 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000013
SEND to > ISAKMP OAK INFO *(HASH, DEL) to *. **. ***. ***
57 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000049
IPsec security association negotiation made scrapped, MsgID = CE99A8A8
58 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000017
Marking of IKE SA delete (I_Cookie = A3A341F1C7606AD5 R_Cookie = F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED
59 15:09:27.459 11/12/12 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = *. **. ***. ***
60 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000058
Received an ISAKMP for a SA message no assets, I_Cookie = A3A341F1C7606AD5 R_Cookie = F1F403018625E924
61 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(dropped)="" from="">
62 15:09:27.490 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
63 15:09:30.475 11/12/12 Sev = Info/4 IKE/0x6300004B
IKE negotiation to throw HIS (I_Cookie = A3A341F1C7606AD5 R_Cookie = F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED
64 15:09:30.475 11/12/12 Sev = Info/4 CM / 0 x 63100012
ITS phase 1 deleted before first Phase 2 SA is caused by "DEL_REASON_IKE_NEG_FAILED". Crypto 0 Active IKE SA, 0 IKE SA authenticated user in the system
65 15:09:30.475 11/12/12 Sev = Info/5 CM / 0 x 63100025
Initializing CVPNDrv
66 15:09:30.475 11/12/12 Sev = Info/6 CM / 0 x 63100046
Set indicator established tunnel to register to 0.
67 15:09:30.475 11/12/12 Sev = Info/4 IKE / 0 x 63000001
Signal received IKE to complete the VPN connection
68 15:09:30.475 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
69 15:09:30.475 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
70 15:09:30.475 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014
Remove all keys
71 15:09:30.475 11/12/12 Sev = Info/4 IPSEC/0x6370000A
IPSec driver successfully stopped
---------------------------------------------------------------------------------------------------------------------------------------
The running configuration is the following (there is a VPN site-to-site set up as well at an another ASA 5505, but that works perfectly):
: Saved
:
ASA Version 8.2 (5)
!
hostname NCHCO
Select hTjwXz/V8EuTw9p9 of encrypted password
hTjwXz/V8EuTw9p9 of encrypted passwd
names of
description of NCHCO name 192.168.2.0 City offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.2.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address **. ***. 255.255.255.248
!
boot system Disk0: / asa825 - k8.bin
passive FTP mode
access extensive list ip NCHCO 255.255.255.0 outside_nat0_outbound allow 192.168.1.0 255.255.255.0
access extensive list ip NCHCO 255.255.255.0 inside_nat0_outbound allow 192.168.1.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access all 192.168.2.64 255.255.255.224
access extensive list ip NCHCO 255.255.255.0 outside_1_cryptomap allow 192.168.1.0 255.255.255.0
access extensive list ip NCHCO 255.255.255.0 outside_1_cryptomap_1 allow 192.168.1.0 255.255.255.0
Standard access list LAN_Access allow NCHCO 255.255.255.0
LAN_Access list standard access allowed 0.0.0.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask of VPN_Pool VPN_Start VPN_End of local pool IP 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 645.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 0-list of access outside_nat0_outbound
Route outside 0.0.0.0 0.0.0.0 74.219.208.49 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
network-acl outside_nat0_outbound
WebVPN
SVC request to enable default svc
Enable http server
http 192.168.1.0 255.255.255.0 inside
http *. **. ***. 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac l2tp-transform
Crypto ipsec transform-set l2tp-transformation mode transit
Crypto ipsec transform-set vpn-transform esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA
Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA
Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5
Crypto ipsec transform-set transit mode TRANS_ESP_3DES_MD5
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs Group1
crypto dynamic-map dyn-map transform 10-set, vpn l2tp-transformation-transformation
dynamic-map encryption dyn-map 10 value reverse-road
Crypto-map dynamic outside_dyn_map 20 game of transformation-TRANS_ESP_3DES_MD5
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs Group1
peer set card crypto outside_map 1 74.219.208.50
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
map outside_map 20-isakmp ipsec crypto dynamic outside_dyn_map
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside crypto map inside_map interface
card crypto vpn-map 1 match address outside_1_cryptomap_1
card crypto vpn-card 1 set pfs Group1
set vpn-card crypto map peer 1 74.219.208.50
card crypto vpn-card 1 set of transformation-ESP-3DES-SHA
dynamic vpn-map 10 dyn-map ipsec isakmp crypto map
crypto isakmp identity address
crypto ISAKMP allow inside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 15
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 35
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP ipsec-over-tcp port 10000
enable client-implementation to date
Telnet 192.168.1.0 255.255.255.0 inside
Telnet NCHCO 255.255.255.0 inside
Telnet timeout 5
SSH 192.168.1.0 255.255.255.0 inside
SSH NCHCO 255.255.255.0 inside
SSH timeout 5
Console timeout 0
dhcpd address 192.168.2.150 - 192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
lease interface 64000 dhcpd inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal DefaultRAGroup group strategy
attributes of Group Policy DefaultRAGroup
value of server DNS 192.168.2.1
Protocol-tunnel-VPN IPSec l2tp ipsec
nchco.local value by default-field
attributes of Group Policy DfltGrpPolicy
value of server DNS 192.168.2.1
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
allow password-storage
enable IPSec-udp
enable dhcp Intercept 255.255.255.0
the address value VPN_Pool pools
internal NCHVPN group policy
NCHVPN group policy attributes
value of 192.168.2.1 DNS Server 8.8.8.8
Protocol-tunnel-VPN IPSec l2tp ipsec
value by default-field NCHCO
admin LbMiJuAJjDaFb2uw encrypted privilege 15 password username
username privilege 15 encrypted password yB1lHEVmHZGj5C2Z 8njferg
username, encrypted NCHvpn99 QhZZtJfwbnowceB7 password
attributes global-tunnel-group DefaultRAGroup
address (inside) VPN_Pool pool
address pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside LOCAL)
LOCAL authority-server-group
authorization-server-group (inside) LOCAL
authorization-server-group (outside LOCAL)
Group Policy - by default-DefaultRAGroup
band-Kingdom
band-band
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared key *.
NOCHECK Peer-id-validate
tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
tunnel-group DefaultWEBVPNGroup ppp-attributes
PAP Authentication
ms-chap-v2 authentication
tunnel-group 74.219.208.50 type ipsec-l2l
IPSec-attributes tunnel-group 74.219.208.50
pre-shared key *.
type tunnel-group NCHVPN remote access
attributes global-tunnel-group NCHVPN
address pool VPN_Pool
Group Policy - by default-NCHVPN
IPSec-attributes tunnel-group NCHVPN
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:15852745977ff159ba808c4a4feb61fa
: end
ASDM image disk0: / asdm - 645.bin
ASDM VPN_Start 255.255.255.255 inside location
ASDM VPN_End 255.255.255.255 inside location
don't allow no asdm history
Anyone have any idea why this is happening?
Thank you!
Add, crypto dynamic-map outside_dyn_map 20 value reverse-road.
With respect,
Safwan
-
This is my first post on this site. Hi all!
I have not really set up ASAs or VPN on Cisco devices before. Currently, I'm trying to configure a dial-up VPN between ASA devices, a 5505 and a 5510. The 5510 is supposed to be the server and the 5505 is supposed to be the easyvpn customer. The reason why I'm opting for remote access instead of site to site is that I much 5505 s on the remote I need to set up in the future, and they will be moving around a bit (I prefer not to have to follow the configs to site to site). The 5510 is not mobile. The ASA devices are able to ping to 8.8.8.8 as ping each other in the face of public IP address.
Neither SAA can ping IP private of other ASA (this part makes sense), and I am unable to SSH from a client on the side 5510 for internal interface (192) of the 5505. I wonder if someone more experienced in the remote VPN ASA than me is able to see something wrong with my setup? I glued sterilized configs of two ASAs below.
Thanks a lot for any assistance!
ASA 5510 (server)
ASA Version 8.0 (4)
!
hostname ASA5510
domain name
activate the
password encrypted passwd
encrypted names of
!
interface Ethernet0/0
nameif outside
security-level 0
IP 48.110.3.220 255.255.255.192
!
interface Ethernet0/1
nameif inside
security-level 100
IP 192.168.191.252 255.255.252.0
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
!
passive FTP mode
DNS server-group DefaultDNS
domain name
permit same-security-traffic intra-interface
permit NONAT_VPN to access extended list ip 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0
VPN_REMOTE_IPS note EZ VPN REMOTE IP access-list VARIES
permit VPN_REMOTE_IPS to access extended list ip 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0
pager lines 24
Outside 1500 MTU
Within 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 613.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside) 0-list of access NONAT_VPN
Route outside 0.0.0.0 0.0.0.0 48.110.3.193 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.0.0 255.255.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-aes-192 TestVPN, esp-sha-hmac
86400 seconds, duration of life crypto ipsec security association
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto dynamic-map DYNAMIC - map 5 game of transformation-TestVPN
86400 seconds, crypto dynamic-card DYNAMIC-map 5 the duration value of security-association
cryptographic kilobytes 4608000 life of the set - the association of the DYNAMICS-Dynamics-card card 5 security
outside_map card crypto 86400 seconds, 1 lifetime of security association set
card crypto outside_map 1 set security-association life kilobytes 4608000
card crypto S2S - VPN 100 set security-association second life 86400
card crypto S2S - VPN 100 set security-association kilobytes of life 4608000
card crypto OUTSIDE_MAP 65530-isakmp ipsec DYNAMIC-map Dynamics
OUTSIDE_MAP interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 1
SSH 192.168.0.0 255.255.0.0 inside
SSH timeout 15
Console timeout 30
management-access inside
priority-queue outdoors
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal EZVPN_GP group policy
EZVPN_GP group policy attributes
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPN_REMOTE_IPS
allow to NEM
username
password encrypted privilege 3 username
password encrypted privilege 15 type tunnel-group EZVPN_TUNNEL remote access
attributes global-tunnel-group EZVPN_TUNNEL
Group Policy - by default-EZVPN_GP
IPSec-attributes tunnel-group EZVPN_TUNNEL
pre-shared key
!
class-map inspection_default
match default-inspection-traffic
VOICE-CLASS class-map
match dscp ef
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map PRIORITY_POLICY
class CLASS VOICE
priority
matches of the QOS-TRAFFIC-OUT strategies
class class by default
average of form 154088000
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:10156ad7ab988ae7ed66c4b6d0b4712e
: end
ASA 5505 (Client)
ASA Version 8.2 (5)
!
ASA5505 hostname
activate the
password encrypted passwd
encrypted names of
!
interface Ethernet0/0
!
interface Ethernet0/1
switchport access vlan 2
!
interface Ethernet0/2
Shutdown
!
interface Ethernet0/3
Shutdown
!
interface Ethernet0/4
Shutdown
!
interface Ethernet0/5
Shutdown
!
interface Ethernet0/6
Shutdown
!
interface Ethernet0/7
Shutdown
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.19.1 255.255.255.192
!
interface Vlan2
nameif outside
security-level 0
IP 174.161.76.217 255.255.255.248
!
passive FTP mode
pager lines 24
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Route outside 0.0.0.0 0.0.0.0 174.161.76.222 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.0.0 255.255.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto ISAKMP policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
No encryption isakmp nat-traversal
Telnet timeout 5
SSH 192.168.0.0 255.255.0.0 inside
SSH 48.110.3.220 255.255.255.255 outside
SSH timeout 5
Console timeout 0
management-access inside
vpnclient Server 48.110.3.220
vpnclient mode network-extension-mode
vpnclient EZVPN_TUNNEL vpngroup password
vpnclient username
password a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
username
password encrypted privilege 15 !
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
destination http address
https://Tools.Cisco.com/its/service/odd... DCEService
email address of destination
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:bd465cea07c060a409a2eade03b487dc
: end
Please follow this link to create a dynamic L2L Remote Server on ASA5510.
Here is a link for you to create the Site to Site vpn tunnel and the tunnel can be customer above tunnel dynamic L2L Server.
http://www.Cisco.com/en/us/products/ps5855/products_configuration_example09186a0080a9a7a3.shtml
Hope that helps.
If you have any questions, please ask.
Thank you
Rizwan James
-
Cisco ASA 5505 - capable to connect to VPN - access forbidden inside
Hello
I tried to set up a virtual private network for weeks, I can connect to the public IP address of the ASA, but I can't reach anything behind Cisco.
I give you my config:
ASA Version 8.2 (5)
!
host name asa
sarg domain name * .net
activate the encrypted password of Z4K16OvBr0J5Dj/2
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address dhcp setroute
!
passive FTP mode
DNS server-group DefaultDNS
domain sargicisco.net
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.1.0 255.255.255.0
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.254.0 255.255.255.240
Remote_Sargi_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
sheep - in extended access-list permit ip 192.168.1.0 255.255.255.0 192.168.254.0 255.255.255.0
pager lines 24
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
mask 192.168.254.1 - 192.168.254.10 255.255.255.0 IP local pool SAVPN_Pool
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside crypto map inside_map interface
crypto ISAKMP allow outside
crypto ISAKMP allow inside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
VPN-addr-assign local reuse / time 5
Telnet timeout 5
SSH timeout 5
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.1.5 - 192.168.1.36 inside
Wis field dhcpd * .net interface inside
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
allow inside
SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image
enable SVC
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
internal Remote_Sargi group strategy
attributes of Group Policy Remote_Sargi
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Remote_Sargi_splitTunnelAcl
sargicisco.NET value by default-field
username kevin mz6JxJib/sQqvsw9 password encrypted privilege 0
username kevin attributes
VPN-group-policy DfltGrpPolicy
type tunnel-group SAVPN remote access
attributes global-tunnel-group SAVPN
address pool SAVPN_Pool
tunnel-group SAVPN webvpn-attributes
enable SAVPN group-alias
allow group-url https://82.228.XXX.XXX/SAVPN
type tunnel-group Remote_Sargi remote access
attributes global-tunnel-group Remote_Sargi
address pool SAVPN_Pool
Group Policy - by default-Remote_Sargi
IPSec-attributes tunnel-group Remote_Sargi
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:387a6e260247a545f4df0d3f28ba58c5
: endThank you
Hello
Could you remove this statement and add the last:
no nat (inside) 0-list of access inside_nat0_outbound
ADD: nat (inside) 0 access-list sheep - in
Kind regards
Aditya
Please evaluate the useful messages and mark the correct answers.
-
«Problems with remote access with ASA 5505-, this is the error "the remote peer is no more answers»
Hello
By train I got a remote access IPSec VPN, when I have all the performed configuration and try to access remote show software vpn client (cisco) the following message:
"The remote peer is no more answers.
I know where is the problem.
Network information:
ASA TO LAN - 1:
192.168.1.0 - 255.255.255.0
the interface vlan 1:
IP: 192.168.1.1 - 255.255.255.0
the interface vlan 2:
IP: 100.100.100.1 - 255.255.255.252
REMOTE LAN ACCESS:
192.168.10.0 - 255.255.255.0
ASA-1 configuration:
* IP address pool
local IP VPNPOOL 192.168.20.1 pool - 192.168.20.254
* Split tunneling
splittunnel list standard access allowed 192.168.1.0 255.255.255.0
* NAT configuration
object obj LAN
subnet 192.168.1.0 255.255.255.0
object obj-vpnpool network
subnet 192.168.20.0 255.255.255.0
NAT (inside, outside) 1 static source obj-local obj-local destination static obj-vpnpool obj-vpnpool no-proxy-arp* Group Policy
internal group company-vpn-policy policy
attributes of vpn-company-policy-group policy
VPN-idle-timeout 30Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list splittunnelConfigure the IPSec
IKEv1 crypto policy 10
3des encryption
sha hash
preshared authentication
Group 2
life 3600
Crypto ikev1 allow outside
crypto isakmp identity addressCrypto ipsec transform-set esp-3des esp-sha-hmac RA - TS ikev1
Dynamic crypto map DYN_MAP 10 set transform-set RA - TS ikev1
card crypto VPN_MAP 30-isakmp dynamic ipsec DYN_MAP
VPN_MAP interface card crypto outsideCreate tunnels
tunnel-group vpnclient type remote access
tunnel-group vpnclient-global attributes
address VPNPOOL pool
by default-group-company-vpn-policy
tunnel-group vpnclient ipsec-attributes
IKEv1 pre-shared-key groupkey123Where is the problem?
Hello
Configuration seems almost perfect. Please share the result of the following of the ASA when you try to connect.Debug crypto isakmp 200
Debug crypto ipsec 200You can take snapshots on the external interface of the firewall to confirm if the packets are reaching the firewall or don't use do not:
capture capx off match ip hostKind regards
Dinesh MoudgilPS Please rate helpful messages.
Maybe you are looking for
-
How can I remove the menu drop-down asking me if I want to allow a plugin to run?
From Firefox 26.0, there is now a drop-down list that appears whenever a Web site with a plugin is loaded, if the plugin is set to "Ask to activate" in the addons > Plugins menu. This drop may be rejected, but always reappears when such a page is loa
-
HP Pavilion laptop TS 14: suddenly unable to adjust the intensity of light 10 Windows
Just today, my laptop will not let me adjust the brightness and has completely removed the possibility of. I'm running on Windows 10 (64-bit) and even once, just today from nowhere won't let me adjust the brightness. The laptop battery is completely
-
Aspire replacement motherboard V3.
I need to replace the motherboard of pn Aspire V3: Q5WVH LA - 7912P rev. 01. The reverend 02 is compatible?
-
I just got an email that I know is going to a lot of other people and sender has probably used the IAB to hide the addresses. I have looked at properties etc but can't find a way to see the list of people who have also received the email Is there an
-
I would like to turn off the graphics card Intel HD on my HP ENVY 17 Quad-j000 t
I have a HP ENVY 17 t-j000 with Windows 8.1 Pro My problem is I would like to disable the Intel HD graphics and NVIDIA run the computer and my view: I can do? Help, please!