Playing a disc error has occurred

Similar Questions

• disc error has occurred (press Alt + Ctrl + delete)

  Hi I use computer hp envy 15 laptop.

  well, when I neglected to test disc (perhaps so many times) black screen, I have error reading disk.
  So I tried to go into the bios and disk self-test.
  But he said 'rapid '. It came not the result that are fail or pass. only a single message 'quick' with 303.

  is it corrupted my drive?

  I hit F2 to check my departure upward and system and hard drive... control of start-up failed, HDD test failed and system has been adopted.
  These tests, I did on Hp advanced.

  So, I typed Esc to use the system restore when he was the starter.

  After 25 ~ 30 minutes pick it up hp had appeared.
  But the message says cannot find the partition.
  and I went to the next step to use recover.
  but I couldn't choose section retrieve (method two) I could choose only command promt. If I could do something for recover.because I didn't not hp recovery kit.

  I know it's really happened... can you help me solve this challenge...

  Hi SLOXI,

  Thank you for visiting the Forums HP's Support and welcome. I read your thread on your HP ENVY laptop and get a white or black screen at startup. Try perform a reset. When you perform a hard reset note remove all USB devices and remove cards memory card reader location. Disconnect all non-essential devices. If that doesn't help try to turn on the computer, on which you begin to press F11 repeatedly until the menu opens. You can do a System Restore. Here is a link to overheating as it may be the cause of the closure. If this does not help at the end of this document it tells you to do a test equipment.

  I hope this helps.

  Thank you.

• Playing a disc error occurred - ctrl alt del to restart

  I have a user who has experienced this message on startup with their Dimension 4550:

  Playing a disc error occurred - ctrl alt del to restart

  Here's what I did in my troubleshooting with no luck:

  1 tried various other ide ribbon cables.

  2 removed all other readers of power and the motherboard with only the first master drive active.

  3 deleted all other drives in the bios, leaving only the primary master drive.

  3 replacement motherboard.

  4 here's the kicker.  I installed XP SP2 on a new fresh (Seagate 320 GB HDD) and after installation and first start, I get the same "disc error".  What are the chances that both disks have the same problem?  Enough of the ratings if you aske me.  So there doesn't seem to be the mother othe, cable or hard disk.  What could be the problem?

  I note that now when I boot from the XP cd it goes to a black screen after the "Setup inspects the current hardware configuration.  I am able to get past this screen if I remove the hard drive and install on another drive clean.

  What the hell is happening?  I'm usually skilled enough to fix these issues, but this one left me speechless!

  Thank you

  Tom

  
  

• Fast forward video its exception throw year error has occurred trying to play media.

  My problem is that if I'm fast video transfer its exception throw year error has occurred trying to play media.

   

  CODE

   

    public MyScreen()
        {
      try {
           setTitle("MyTitle");
  
          Invocation invocation = new Invocation("http://dl.dropboxusercontent.com/u/17458564/Nueva%20carpeta/Video/lovingyou.mp4;interface=wifi");
          // Get the Registry object using the class name of the application
          Registry _registry=Registry.getRegistry(Application.getApplication().getClass().getName());
          //Invoke the content handler.
          _registry.invoke(invocation);
      } catch (IOException e){
      }}Any solution will be appreciated Thanks
  
  
  

   

  Hi @tej,

  I'm assuming that you actually see the core MediaPlayer card app transition when you perform this invocation. But if this is the case, you simply reference to a * looking to come * operation from the progress bar? (i.e. component UI slider). Because the only way you can actually get a * operation forward fast * is increasing reading speek, through the Cascades MediaPlayer API or mm-renderer C API; links to documentation for the MediaPlayer card above, there is no way to specify the quick delivery.

  Now, assuming that your * search * operationg is a failure, it could even be on how Dropbox is expected or with HTTP calls. A few things to consider (the URL you pasted is not accessible to me, at least my network to work here):

  (1) the same video file works with the search when you already downloaded on your phone (which is pointing to a local path instead)?

  (2) the same Dropbox URL works perfectly well with the streaming/looking for a browser based player? (for example VLC client on the default player on Google Chrome or Firefox)

  For example, here's a .mp4 from a video podcast site: http://dts.podtrac.com/redirect.mp4/twit.cachefly.net/video/tnt/tnt0920/tnt0920_h264b_640x368_256.mp...

  Let us know what you think / search.

  See you soon,.
  Rashid

  Applications development consultant | Relationships with developers

  BlackBerry @surashid

• Move to the new computer, get "an error has occurred during playback of files or write files to a disk." The disc

  • I tried to move my catalog and PE6 install to a new computer.  This is on a Dell Windows XP machine, and I moved it to a Toshiba Windows 7 (64-bit) machine.  I always kept my photo on an external hard drive files.  My library is 50 GB, 10,000 files.  Here's what I did.
    • Copied the original PE6 installation file on the Toshiba.  Installed but not activate it.
    • Copied my catalog folder to the location of the Windows 7.
    • Plug the external drive into the Toshiba.  So makes that same letter drive as a front.
    • Fired up to PE6 on Toshiba.  Seemed fine in the Organizer.  Everything seemed to be there, but I didn't try to make any changes at this time there.
    • PE6 disabled on the Dell.  Enabled on the Toshiba.
  • Then I realized that it is not fair.  I can edit the keywords and the stars rating on photos, but not the dates, legends or notes.  I get "an error has occurred during playback of files or write files to a disk." The drive is may be full, or there may be problems with the source media. »
  • Only a fraction of the external drive is in use.
  • I can access the files on the external hard drive with another application (Windows Photo Viewer).
  • I tried the reconnect All missing files.  Somewhat ambiguous, she said "There are no files to reconnect."
  • In the properties in the organizer for each photo are the appropriate file names and paths.  Folder view works fine in the Organizer.
  • I can put new files in the directories of the same external drive, import them into PE6, then change them normally.

  What is the best way to get Organizer connected correctly to my files?  I guess I could import all photos on the new machine, but I guess I'd lose some of my metadata.  So it's out of the question.

  Thank you

  Bill

  Well, the recommended method for moving the catalog is to use organizer of the PSE6 on your old computer to do a full backup on your DHM.  (Which backs up the catalog and media files).  Then, on your new computer, open the Organizer PSE6 and restore from this backup.

  Your method seems logical, but...

  Ken

• VPN connection: An unexpected error has occurred.

  I am suddenly unable to get my built-in VPN connection works on my iMac with OS X 10.11.5.  I get the VPN connection message: an unexpected error has occurred.  I have been using this VPN configuration to connect to work for several months with success.

  But last week (and I do not know if it had nothing to do with it), I went on vacation and used a free wi - fi setup of Tim Hortons.  I had a LOT of trouble getting the next login page, and I checked all playing with different settings of network without success.  When a change did not work, I put it to its original setting.  Finally, I learned to use Safari to access the free WiFi connection page of Tim.  Then once connected, everything was OK.

  But when I returned a week later and if necessary, to start my VPN connection to access the work, it wouldn't start.  I checked and recheck all my settings preferably of different network, but did not find those who were wrong.  I even deleted and re-entered my VPN service definition without solving the problem.

  Thinking that the problem could be the newly installed ISP of Bell equipment (we went from Rogers while I was away), I used my BlackBerry smartphone (issued by my employer) to create a wi - fi hotspot and accessed to the internet using this connection which completely ignored my home ISP equipment.  But still, I was unable to establish a VPN connection.

  I then tried my iPad VPN connection, and it worked!  Then, I defined a VPN service on the iMac to my wife and the iMac to my daughter and was able to successfully establish a VPN connection to my work very well, using exactly the same VPN configuration.  This led me to the conclusion, it was a problem on my iMac (and not with my new ISP or VPN system of my work that had none of the changes you made), but I still can't find what is "broken".  I run Onyx for my iMac OS X 10.11.5 and repaired permissions and clean the cache and all the rest she is doing to "solve" problems.  But the problem persisted.

  Is there a preference file corrupted somewhere (scan option is no longer on the current version of the Onyx for a reason any)?

  I still have a network setting wrong somewhere I need to go back to the system is correct value?

  Here is the attempt to VPN from the file system.log (with some hidden values in the case where they display my work VPN access):

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: NESMLegacySession [VPN works: 295091E5-xxxx-4B6A-xxxx-F7A7xxxxxxAA]: received an order to start SystemUIServer [257]

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: NESMLegacySession [VPN works: 295091E5-xxxx-4B6A-xxxx-F7A7xxxxxxAA]: changed to connecting status

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: IPSec connection to server nnn.nnn.n.n

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: phase 1 of the IPSec from.

  26 June at 16:13:48 Myrons-iMac raccoon [520]: agreed to the takeover of vpn connection.

  26 June at 16:13:48 - last message repeated 1 time-

  26 June at 16:13:48 Myrons-iMac raccoon [520]: IPSec connection to server nnn.nnn.n.n

  26 June at 16:13:48 - last message repeated 1 time-

  26 June at 16:13:48 Myrons-iMac raccoon [520]: connection.

  26 June at 16:13:48 Myrons-iMac raccoon [520]: IPSec Phase 1 started (initiated by me).

  26 June at 16:13:48 - last message repeated 1 time-

  26 June at 16:13:48 Myrons-iMac raccoon [520]: bind 1 (cannot assign requested address)

  26 June at 16:13:48 - last message repeated 1 time-

  26 June at 16:13:48 Myrons-iMac raccoon [520]: sendfromto failed

  26 June at 16:13:48 - last message repeated 1 time-

  26 June at 16:13:48 Myrons-iMac raccoon [520]: Phase 1 negotiation failed due to the error of sending. 94437eb7d5b1b6e8:0000000000000000

  26 June at 16:13:48 - last message repeated 1 time-

  26 June at 16:13:48 Myrons-iMac raccoon [520]: can not send packets

  26 June at 16:13:48 - last message repeated 1 time-

  26 June at 16:13:48 Myrons-iMac raccoon [520]: IKE Packet: send failed. (Initiator, aggressive Mode 1 Message).

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: Controller IPSec: IKE FAILED. Phase 1, assert 0

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: NESMLegacySession [VPN works: 295091E5-xxxx-4B6A-xxxx-F7A7xxxxxxAA]: status changed by disconnecting

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: IPSec disconnection from the server 142.201.5.6

  26 June at 16:13:48 Myrons-iMac raccoon [520]: IPSec disconnection from the server nnn.nnn.n.n

  26 June at 16:13:48 - last message repeated 3 times-

  26 June at 16:13:48 Myrons-iMac nesessionmanager [439]: NESMLegacySession [VPN works: 295091E5-xxxx-4B6A-xxxx-F7A7xxxxxxAA]: status changed to offline, terminus right no

  Any help or insight would be more useful and appreciated... so that I can work from home again.

  Thank you

  Myron VanderLaan

  I finally found my VPN problem.

  There is a 'racoon' file that is generated when I connect to the VPN to my work site.

  I have created a modified version of this file so that my connection does not expire in 3600 seconds (changed in 24 hours).

  Apparently, there are some slightly different settings (such as certain IP addresses other than VPN IP of my work) in this file under our new ISP Bell from the former FAI Rogers.

  And if I connect to the WiFi Hotspot from my BlackBerry, it does not once again because these settings in the file are different again.  I must return the file generated instead of my modified file.

  Bad luck!

• Installed more recent Flash Player, message "an error has occurred" on most of the Youtube videos and other media does not

  After you have installed the latest version of Flash Player, on the YouTube videos, I try to read the message "an error has occurred. Please try again later. "appears. In addition, on sites like Tumblr other media, such as audio and videos uploaded, play not at all - it's just a white space where it should be. This set works fine in Chrome.
  I have tried everything I can think of - I deleted the cache and deleted cookies, updated all plug-ins, uninstalled and reinstalled Flash and Firefox, disabled Ad-Block, he ran in Safe Mode and navigation private, restarted my laptop a couple of times - but none of this has worked.

  Try turning off protected in Flash drive mode.

  See:

  • [929081/questions/929081]
  • [/questions/928820 #answer - 340046]

• An unexpected error has occurred - Apple tvOS 9.2

  Since my Apple TV 4 Gen tvOS 9.2 update, I have problems w / playing some movies I have purchased through iTunes. Get "an unexpected error has occurred" and an ignore"" button. The titles of films even play fine on my Macbook, iPhone and Windows PC. Replaced my Apple TV 4 material during the weekend but the problem persists with the replacement unit. Contact Apple Support confirmed reports addtl of the problem and how it could be related to a recent change in the backend to the iTunes store. Help w / titles problematic movies. If anyone knows the same thing, support both want to hear from you.

  Have the same problem
  bought nine ATV4

  Do not play anything on the account

  Does not buy new movies

  "Unexpected error".

• Activating Windows indicates that an error has occurred

  Last night I had an open window that told me there was an error activating windows and that my version of windows was not valid. When I try and open the Windows Activation it tells me an error has occurred. Code: 0 x 80070424.

  I use the windows which was preinstalled on the computer. BUT, I ended up having to purchase backup discs from Toshiba and the service center he relocated to me. Not sure if there is a problem or if it is internal.

  Help, please.

  Thank you

  Will be.

  Hi Will,

  And what you say now? If I understand the computer is now reinstalled with Toshiba recovery disc, so all is ok now or you always have problems?

  The version preinstalled Windows from Toshiba is still active and read to use so that I can t imagine you must activate your copy of Windows if it was preinstalled on Toshiba drive or recovery

• Satellite U300: "an unexpected i/o error has occurred."

  Hello

  My newly purchased U300 worked fine, today would not start and is now indicating that an unexpected i/o error has occurred, with a code of 0xc00000e9

  The message preceding that States that this may be due to recently responsible for hardware or software. Not apply.

  Any help appreciated, thanks

  Janie

  Hello

  These errors are often errors in registry. Could be caused by some software disk cleanup or somehing else who has access to the registry system´s.

  The only option is to fix the system with an original disc of Windows Vista. If you don t have such a, then you will recover you the system because your registry database cannot be recovered, and the system must be completely replaced.

  If you do not already have: backup your personal data... That's all

  Greetings

• Satellite L300: Failed to retrieve - unexpected i/o error has occurred

  Help, please...

  I'm trying to restore the orginal through recovery process.
  After pressing F8 at start-up stage and chose to restore the system, he thinks about it, and then comes back with the following error;

  STATUS: 0XC00000E9
  INFO: An unexpected i/o error has occurred

  There is also an explanation it may be due to an external device that has not been properly disconnected or a hardware error.

  I have nothing plugged and restarting the system several times to try to resolve the problem. I also tried to re-boot last secure configuration, but this has not helped (although now gave me my card back like this so that other issues have been a problem - that is why the desire to recover the original system settings).

  Any advice would be greatly apprciated.

  Thank you.

  Hello

  Allows summary;

  -You are not able to start the Windows operating system (even in safe mode)
  Right?

  -You are not able to recover the laptop with HARD drive recovery option.
  Right?

  -You don t have a recovery disk
  Right?

  Well in that case I n t see any other solution for new order recovery disk and then try to recover the laptop using this disc.

  You can order the CD from recovery here:
  https://backupmedia.Toshiba.EU/landing.aspx

• multimedia card reader an error has occurred please drive reconnect to try again

  I have windows xp 32 bits SP3. I tried to copy the computer on a CD - RW disc images and a message kept popping up on the office.

  Multimedia card reader. An error has occurred please reconnect reader to try again. I got my coppied photos on the disk, but did not know what that message was talking about. It kept popping up.

  Hi Connie,

  1 is this problem limited only when you copy images from the computer to CD?

  2. What is the full/exact error message?

  3. have you connected any external to the computer card reader recently?

  4. What is the brand and model of the computer?

  It seems that the installation of the driver of the multimedia card reader is not over. If you have connected to any card reader recently, you can re - connect to the computer and allow the computer to detect the device.

  Hope this information helps. Provide more information so that we can help you.

• Outlook express 6 on startup reports "an unknown error has occurred."

  Outlook Express 6 has started saying "an unknown error has occurred" (no other text message).  This only seems to happen when I run after she is not running for a while (an hour or two).  If I close and run it again immediately, the error does not occur.  I read in the forum, someone say the folders.dbx file is damaged or missing, and the advice to rename it to folders.old, causing Outlook Express to create a new folders.dbx file.  I hesitate to do that I have several years worth of emails in the system and do not know if I would lose them by forcing the creation of a new file.  What is the function of the file folders.dbx anyway?  How is it, you can rename just to old point and get a new one?  Is there something important in there?

  The only trigger I can think of for this error started to happen, is that I deleted a large number of emails sent just before he began to arrive.  I had sent a large number of photos to friends, and I thought I want to remove messages as they would use space disc unnecessarily masses.  Outlook Express and then put them in a "Deleted" folder, that I also went and deleted all the posts in there.

  Try first the compaction. When you delete messages, the space they took is not recovered until you do.

  Click Outlook Express at the top of the the folder tree so no folders are open. Then: File | Work offline (or double-click on work online in the status bar). File | Folder | Compact all folders. Don't touch anything until the compacting is completed.

  Compress your OE folders:
  http://www.insideoe.com/files/maintain.htm#compact

  Folders.dbx is the "brain" of the system of dbx files.

  In Windows XP, the files of user OE (DBX and WAB) are by default marked as hidden. To view these files in Windows Explorer, you must enable Show hidden files and folders under start | Control Panel | Folder Options icon | Opinion, or in Windows Explorer. Tools | Folder options | View.

  The path to the message will be very similar to this:

  C:\Documents and Settings\Your User of utilisateur\Local Settings\Application Data\Identities\ {long string of letters & numbers} \Microsoft\Outlook Express

  With OE closed, find the Folders.dbx file and delete it.  Another will be created automatically when you open OE.

  Note these possible side effects: (you will not lose messages)

  When you re - start OE, it will build a new index of all *.dbx files it can read and create a new Folders.dbx. However, understand that you will lose the mail directory structure and message rules will probably have to be edited.

  Or, you can create a new identity which is probably the best correction. File | Identities | Add the new identity. Create a new one and try it. If all goes well, you can import your messages and address book from the old identity and delete it.

  Note: Do not use the main word in the name of the new identity.

• Get the error during the installation of Windows XP Professional: a fatal error has occurred. Setup cannot continue.

  I get the following error message when you install Windows XP Professional: a fatal error has occurred. Setup cannot continue. Please contact your support representative or a seller/provider untorised. Press to stop the system. I have real service pack 1 XP and the restore CD. After the restoration CD Formate the hard drive and installing Windows starts, he cannot continue and cela happened on two different PC (HP dx2000 and HP dx2300MT. Help, please

  Hello

  As has happened on two computers, I would look on the disc as the problem.

  "I have genuine XP service pack 1.

  What is the exact drive do you use?

  See you soon.

• An internal error has occurred in Windows Media Player

  I write on behalf of a client who has a few problems with Windows Media Player in Windows XP.

  She said that she receives the error message "an internal application error has occurred" all the time. He will not play CD and does not even start.

  She wonders if she needs to unintall/reinstall. However, she received another message saying something like its other programs may not work correctly.

  Just to confirm yet for her, she would not lose all other programs in the cases where she unisntalls Windows Media Player, right?

  Thank you!

  Thank you.

  Hello

  • What were the changes made before the issue occur?
  • How long have you been faced with this problem?

  You can check this link:

  You may receive an error "internal application error has occurred" message when Windows Media Player will automatically try to read a CD or a DVD in Windows XP

  http://support.Microsoft.com/kb/899873