Port 902 does not listen on TCP

Similar Questions

• Port forwarding does not work on EA6900

  Please help me to know what is the reason for this port forwarding does not work on my Linksys router:

  Model: EA6900 v1.1
  Firmware version: 1.1.42.161129

  I've set up two ports: TCP 22 and 8070 TCP to 192.168.1.10. (192.168.1.10 is up and running, I can reach the LAN ports).

  Yesterday, I had a live chat with Linksys support we tried to re - download the firmware even, but that did not help. Then factory reset and reconfigure the router did not help either.

  Unchecking "Filter anonymous Internet requests" and disable uPNP didn't help either (they have been suggested in similar topics).

  However, the IP displayed tab troubleshooting/Diagnostics reflect my external IP address (the IP displayed by http://whatismyip.com), which is weird, because I never have IP from my ISP from 100, that is displayed on the Diagnostics tab. So I guess it's a fake display or it relates to access to my router via www.linksyssamrtwifi.com ?

  Anyway I tried the two IPs from the outside, but the transfer simply doesn't work. (It works fine when I use my old router TP-Link).

  Please advise!

  Sorry guys, it seems indeed a double NAT problem. My ISP can detected MAC address change when I started using EA6900 (thinking that I couldn't not need public IP?) and since then he sends me IPs for NAT - ed. It is strange that the same day, he was working with my old router, but now it is even not working with my old router and not even working when I connect directly to my windows PC to my ISP (via PPPoE). I called their support line and they said that they will solve this problem within 72 hours. In any case, thanks for your help!

• FC Port-Channel does not

  Hello

  I need help, I'm setup CF port-channel between 9148 MDS and Cisco fabric Interconnect 6248 and the port-channel does not work. He said no operational members.

  For the MDS, see configuration below:

  NPIV #feature SW (config)

  SW (config) #feature fport-channel-trunk

  SW (config) #interface fc1/17-18

  SW(config-f) force Group-channel mode # 63

  SW(Config-if) F #switchport mode

  SW(Config-if) #switchport trunk-allowed vsan 1-2 (I have only vsan 1 and 2)

  SW (config) #no close

  SW (config) #interface 63 port channel

  SW(Config-if) F #switchport mode

  SW(config-f) #switchport trunk-allowed vsan 1-2

  SW (config) - #no close

  Note: the ports are assigned to vsan 2

  See the attached screenshots for interconnection fabric config

  On the fabric of interconnections switchport mode are defined E. What I have to change to F. If yes where can I change since the option is not there in the UCS Manager?

  have you added the VSANS on the UCSM as well?

  What Code are you runnig on the San Norhbound selector?

  You can be hitting

  https://Tools.Cisco.com/bugsearch/bug/ CSCty04686

• Port 139 does not not on Windows 7 after deployment.

  Hello

  I created some images of new installations of Windows 7. But the pack of GPO that is applied in MDT 2012 changes settings in windows 7 so that port 139 does not correctly work with gap analysis network SMB.
  recently we bought workstations that already have a Windows 7 image on them. But because computers OS was deployed hollow some imaging modalities 139 port does not work properly. Is there such a tool from Microsoft to restore the port 139 on a charge CD Windows 7 feature?
  Or any Microsoft employee who has done any research into this problem and tested and found a solution to this problem?
  Thank you.

  You can take this on the Technet forums because I don't know where the sizes are fixed. One thing to remember when the GPO is that in many cases, changes may "tattoo" the registry and must be explicitly changed back instead of be reset to the default value.

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

  I hope this helps.

• When I plug my portable hard drive to the usb port it does not read and display the contents...

  When I plug my portable hard drive to the usb port it does not read and display the contents...

  Hi deaza,.

  Ø Have you connected the USB hard drive to the computer directly or you have used an external USB hub to connect?

  O trying to connect to another USB port to check if it works?

  O the hardrive shows in windows of the computer when you connect it?

  Method 1:
  If you have installed security software, I suggest you to temporarily disable the security software and connect the USB and check to see if the same problem happens. Make sure that you enable the security software after checking.

  Alternatively, you can try to plug the USB key into a different USB port and check if it helps.

  Method 2:
  I suggest trying to launch hardware and troubleshooting of devices and check to see if it helps, here is the link:http://windows.microsoft.com/en-US/windows7/What-to-do-when-a-device-isn ' t-installed-correctly

  Method 3:
  If this does not help, then follow these steps:

  (a) remove all your USB devices. Use the safely remove the feature to turn them off.

  (b) open Device Manager and navigate to the section for USB. Uninstall all USB drives. There should be one for each USB port, and then restart.

  To open Device Manager, go to the link below and follow the steps:

  http://Windows.Microsoft.com/en-us/Windows7/open-Device-Manager

  (c) Windows should re - find all of the devices. If it is not the case, note the error message and let us know.

  You can also navigate to the link below and follow the steps to install the USB device.

  http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Standard vSwitch_Custom VM (Vlan200_VM network) port group does not.

  Hi guys...

  Scnerio:

  ESXi 5.0

  VCenter 5.0

  2 connected local network cards to vswitich 0 Active\Active configuration.

  The virtual computer name: FSAPP_1

  Note: good VLANS are created externally NETWORK

  I created another group of ports VM network VLAN 200_VMnetwork.

  I have attached TWO maps LAN to VM. A LAN card is connected to the port default VM network group and another is connected to network VLAN200_VM.

  A LAN card is connected to the local network (Private IP) and another is connected to the Wan (public IP)... IF I CONNECT the TWO VMNIC "DEFAULT virtual machine network" I am able to ping both subnets.

  
  

  But any vNIC which is connected to the VLAN200_VM network is NOT working...

  
  

  
  

  Please see the attached snapsshots...

  Thank you

  I did not ask you to do what I asked you to test is the separate two VM on the host even be configured to use the VLAN 200 portgroup and verify that these two people are able to talk to each other.

  Once you've found that the books above. Go back to your network team and make the request to configure the switch in the trunk output ports (which does not remove the tag VLAN on the package on the output of the switch) as opposed to be defined as access (that strips the tag VLAN).

  It is my firm belief that the port group does not work because your switch is misconfigured based on my above statement.

• New for iPhone charging Port 6 does not

  Recently, I had the charging port on my iPhone replaced 6, because the original had stopped working properly. With the original, I had to shake the charger autour so he could load, but it was so bad that I could only load if I it held in place. I went to a store local tech to g

  With the new port, I am able to load it with a standard charger Apple iPhone or iPad. However, it does not charge to something else - in the car, with a cell phone charger, when it is connected to my Mac - nothing. When it is connected to these other devices, the phone doesn't even it is plugged.

  Thoughts?

  Means, "went to a store local tech to fix.

  Looking for advice!

• Pavilion 23-b320: Port SD does not

  When I insert one of my SD cards in the SD port, the computer does not meet the presence of the SD card.  When I open file Explorer, the SD card does not appear.

  All USB ports work.

  How to solve this problem.

  Note: this computer is my wife, and he sat on his desk for 2 years unused.  We got married recently and am now trying to get to the top and running.  I have done all the necessary updates for all programs.

  I don't have a recovery disk.

  Interesting...

  See if this driver works instead.

  The W8 driver for your model page shows it has a Realtek card reader.

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_155234_1

• N2048 port security does not

  Hi Experts,

  Only, we have deployed a new site that uses the Dell N2048 switches in a stack.

  Now we would add port security to the switch, Port-MAC locking to lockdown one port if another computer.

  According to the manual, to put in place we only need of to the port to locked under the MISTLETOE under switching, network security, port security.

  This does not activate it.

  We tried to add via the command line, in the ports of test, it now shows:

  switchport security of dynamic ports 1

  Still, port security is not enabled. There is another thing that must be enabled in the world to do this job or other commands?

  Thank you

  The output of port security-# show is as follows:

  Port Security Administration Mode: enabled

  It is possible that the tests were not done fast enough. I spent the time-out and ask them to test again.

  Thank you

• PowerConnect 2824 Ports SFP does not

  We bought a new switch 2824 with a corresponding to SFP module replace old 2724 PowerConnect and SFP module.

  After the configuration of the switch and installing it, we were able to get a connection on our uplinked to fiber.
  SFP light illuminates and flashes from time to time, and the switch detects correctly module SFP is inserted and that the fiber is connected.  We can see the insertion of the SFP is detected and the switch for change of fiber mode by looking at the output of the console, and the web administration port status page lists the port as "ComboF" when the SFP is inserted and the fiber is connected.

  However, the switch always indicates that the port State is down.  (The port is not administratively disabled.)

  The old switch works very well with the old SFP module.  The new switch does not work with the old or the new module SFP.  We tried two combo SFP ports.  We also checked that the fiber itself is fine. We cannot get the new switch to display the drop-down list port status that up when you use the SFP. We tried to completely reset the new switch by removing the configuration file via the boot over the serial connection menu and re-run the initial configuration wizard, but the port still won't go up.

  Any ideas?

  After a few tests yesterday, we determined that part of auto-negotiation must be disabled for switch work with our copper and fiber Media converters.

  The 2724 works very well with our media converters, with auto-negotiation enabled.

  The 2824 works very well with auto-negotiation enabled when it is connected to an another SFP transceiver in building switch.

  But when we introduce the Media Converter in the path, the 2824 will bring only the link up if you disable auto-negotiation.

  So far, everything looks good.

• Junction UCS ports worksheet does not, no integration of WWW.

  Hello!

  Key:

  VLAN 200 - all the 20.1.1.0/24

  VLAN 201 - 20.1.2.0

  VLAN 202 - 20.1.3.0

  VLAN 203 - 20.1.4.0

  VLAN 204 - 20.1.5.0

  Just migrated some UCS, HCI SuperMicro and physical servers above 5ks/fex again 9 k column spinal/leafs Cisco ACI running.  Worked well on the 5ks, access ports if necessary, logs allowing VLAN 200 to 204 will stuff UCS and SuperMicro.

  Before I continue, note I am NOT currently any VMM integration, just try to get the same trunk ports to the beach above of VLAN on ports leafs. ***

  Thus, servers physical and other access ports work perfectly.  The links of the trunk of the UCS and SuperMicro don't seem to work right.  By focusing on just the UCS, I can see the entry ARP for the UCS himself, but no resolved IP address.  In addition, I don't see any MAC/IP addresses the Server Blade, or anything else.

  For static bindings EPG, I tried marked (assuming that the law) and not signposted.  ENCAP different VLAN (current vlan-203) but nothing seems to work.  Side of a LLDP and CDP UCS active as I was.

  Speaking of VLAN, I built 5 EPG to do this, each corresponding to a function from one of the 5 VLAN above.  However, the UCS trunk links should allow all VLAN 200-204.  I have a jump on 20.1.2.5 server that cannot call the 20.1.2.x IPs who also live in the UCS, because there are certain types of disconnect to the where the ACPI cannot see in the links of the trunk at all.  I don't know if it's related or fabric EPG associated config.

  I would be very happy to provide additional information, because I'm dead in the water.  Thank you very much.

  Josh

  It depends on if the non - UCS hosts are on the same sheet or not.  You can map an EPG on different ports with some tag and others do not.  There are the limitations when you want to have multiple ports on the same sheet as however no marked.  A single VLAN ID cannot be the tag & unidentified on the same sheet. Even when we put a static as path "unidentified, or 802.1 p ', still need to assign a VLAN unique traffic (can not also be VLAN 201).  It's really a VLAN arbitrariness to the fabric only.  Any evacuation traffic or infiltration of the connected device would send/receive traffic without a tag VLAN.

  Example let's say you have a UCS connected on port 1 and a re-usable on port 2 (same sheet).  You can set EPG - A 'tag vlan 201' for the UCS, and "untagged vlan-205" ports for re-usable connected ports.  Even if the program is different, it does not matter.  The two ports will land in the EPG even at the end of the day and be able to communicate.

  Make sense?

  Robert

  Here's what the config would look like. * Note that my pool VLAN ranges from 200-205, since ACI must allocate a VLAN of the pool especially for unmarked ports (System requirements).  As your hosts are directly connected to the canvas, the VLAN is arbitrary.  We just want that they arise in the EPG even.

  Capture1.jpg

  

  capture2.jpg

  

  capture3.jpg

  

  capture4.jpg

  

• Satellite 5200-902 does not start and several errors

  Hello

  I had a serious problem with my computer.

  While playing a game, the screen become corrupt. It is difficult to describe but basically blocks of colors appeared on the screen and icons became corrupt, lines and points seemed and the screen seems to tremble. The stoppage, the office appeared, and then the corruption of screen appeared again. A Blue Screen of Death appeared, but I couldn't read what he says because the display corrupted again. The laptop then restarted. Ran scan disk and when the computer was upward and the performer said he had just recovered from a mistake serious etc etc. But he did not know what had happened to other than a general driver error.

  At this point, I backed up all my files on my external hard drive.

  The laptop was then suffer from the same issue of corruption to screen again and again, but apparently only after being on for > 5-10 minutes. This time, the BSoD said that it was my graphic drivers and specifically the NV4_disp.dll. So I restored my graphics drivers on the originals included with the computer, but the same error happens again.

  My DVD Multidrive had stopped playing CD a week or two before it (a problem that I was intending to settle). However, mysteriously it started to work again after the first error. So I decided that the only thing I could do was to restore the computer. So I did. However when he asked for the second CD to be inserted the drive does not recognize it (a series of jarring and whirs repetitive of the reader in the same way exactly, that it had been a week or two before; though even when it would not read anything else, would still read DVD about 40% of the time). I tried several times, but meanwhile, the corruption of the display is back!

  I had to cancel the process and the Multidrive still refuses to read the recovery CD and so the laptop computer simlpy cannot be restarted. The most concerning thing now is that the corruption of screen returned when I finally tried to start the computer with the recovery CD - text was corrupted and polyhedral and randomly on the screen. The laptop is now off.

  I fear that it is a hardware failure. I don't see how it could be a virus because one) my anti virus (Norton) was only two or three days from its last update and b) display corruption occurred still even after that the hard drive had been partially formatted by the restore disc, and Windows had not yet started.

  Does anyone have advice? The problem is that I can't boot from the restore disc (unless there is a way to boot from an external CD drive?) and given the corruption of persistent display, I am not yet convinced that that would solve the problem anyway.

  Thank you very much in advance.

  Hello

  I've read about similar problems with the graphic driver or the graphics card of the internet and it happened more often during the game.
  I think it might be an overheating of the graphics card.
  You know that the games are a heavy application that needs a complete service for laptop.
  All portable devices run in this case with a maximum yield and produce a lot of heat.
  I think that it could have a bad influence on the map. As you say the problem appeared after 5-10 min. I think that in this time, the temperature has been increased.

  So I don't know how to help you. I think you should ask the technician for the control of the laptop. Eventually the cooling module must be replaced and if the graphics card has a malfunction, in my opinion, it should be replaced also.

• Port replicator does not work with Satellite P100-160 & Vista

  I just bought a Toshiba duplicator (part number: PX1173U-1PRP) but it does not work with the o/s Vista pre-installed on my P100-160. Can someone tell me where to find the Vista drivers for this device?

  It seems that the standard driver is not compatible with Vista and so you will need a new from the Toshiba page.
  You must remove the old driver and then install the new version.

  Good luck

• HDMI port/switch does not

  I just got my HP Envy tilt 23-k011 and work on getting, he was put in place last night. I tried some of the features and tried hang both my XBox and a cable box (not simultaneously) to the HDMI in port on the lower left side of the screen. Have been recognized. I turned both on and outside sources. I have enabled the button under the screen that says it is supposed to switch the PC to the external video source and nothing no matter how many times I pushed or how long I held in there.
  
  I have updated the drivers for two video cards integrated and dedicated. I rebooted several times. I tried to download a driver of hp pip, but it is not compatible with my model.
  
  I can't find the settings for the display or graphics that refer to external sources to go to. I can't even figure out it's a hardware or software problem.
  
  Does anyone have any suggestions?

  the solution for me was to:

  Press the windows key and type 'hp my display'

  Now your hdmi button should work.

  to make this permanent is restarted, go to the tab the hp my display UI options and check "run as the system starts.

  (I don't know why there are so many messages on this and suggested that not a single representative of HP)

• LRT214 Port Forwarding does not

  First of all, when you create a service in the port forwarding section, why to select the two TCP/UDP has been omitted from the selection must be embarrassing for Linksys.  Creation of 2 services, one for the other for UDP and TCP are bad design.  Would love to see that this problem has been corrected in future updates of the firmware.

  The main problem is I have configured port forwarding services, but I can't get anything to work.  I am able to access remotely to the router using the port 1443 that is configured in a separate section.  I worked in the network design and mgmt for 10 years and why Linksys decided to make the management for the LRT214 so different interface, then the rest of the market was a bad decision.  Is there anything else you can suggest to help out why these ports cannot be opened through the FW?

  On this router logs show nothing.  There is no log for blocked inbound connections and there is a class router business?

  After setting up some boxes of Windows on the local network, then transfer to a custom RDP listening port, I am able to RDP in these Windows boxes remotely.  It verifies that the Linksys router is forwarding ports correctly.  The question then is something on the Synology device itself.  Thanks for your response!