Portege 4010 - upgrade memory

Similar Questions

• Portege 3500 - upgrade memory

  Necessary upgrade memory for a p3500. 'Expert' advised two sticks of 512 MB PC133, but on opening the rear of the location that a laptop computer and on the insertion of the new RAM it gives an error code beep. Is there than a single slot? and if so what maximum capacity and what type of RAM will it take?

  Hi Jeffrey,.

  As far as I know the 3500 Series provided with a removable module of RAM of 128 MB, 256 MB or 512 MB depending on what model and specifications you purchased. There is one other remaining slot for expansion purposes.

  The total support for the 3500 Series RAM is 2 GB and the type of RAM should be SODIMM PC133 144 pins.

  It is important that you match the RAM modules that your RAM module existing (one removable) is of the same type you new RAM module. Of course, you can always delete the original from the RAM and insert two new modules of RAM instead.

  Please check the following URL for more information on the available RAM module type.

  http://www.orcalogic.co.UK/ASP/ProdType.asp?ProdType=5371&ft=m&St=3

  HTH

• Portege R100: upgrade memory

  I´d like upgrade my R100 with a 1024MB key. Can I use the memory with the following specifications?

  DDR266 PC2100 SODIMM 200-pin

  Or are there things more I ve to watch? Or is there still to be a special memory for the R100 custom?

  Thanks for the tips!

  Yes, definitely Yes!

  According to the information on this page, you can use PC2100 200 pin memory (266 MHz) DDR SODIMM
  http://www.orcalogic.co.UK/ASP/ProdType.asp?ProdType=7233&ft=m&St=3

  It seems that there is only one slot for expandable memory. Therefore, you can use a 1024BM of modules like max.

• Upgrade memory on Portege 4010

  I want to upgrade my memory Portege 4010 and I know that I need 144 pins/PC133 SO - DIMM SD - RAM. Unfortunately I couldn't understand (in the same after talking to the Toshiba Austria), if I have to buy memory may be high or low density.

  Most of the memory at low prices on eBay is high density and I'm afraid to buy an incompatible.

  I hope that someone already has experience with it. It seems to be my last chance to get some relevant information.

  Thank you.

  As I remember for Portege 4010 maximum memory is 1 GB (2 x 512 MB) and no matter if you choose the version high or low density.
  If you need 100% guarantee you choose the version of low density.

• Portege 4010 - after upgrading RAM, nothing happens

  Hello
  A beginner very believed in that.

  I picked up some 512 MB PC133 SDRAM for my 4010 but when I put them in the slots and pressing the power button... Nothing happened.

  Would appreciate any help at all...

  Hello!

  Yes, maybe 2 x 128 MB modules were the original modules, that they were delivered with the laptop.

  I think you should try other modules. If you use the modules of noname, they could be possibly not work or problems as bluescreens etc.
  As far as I know that the Portege 4010 can be upgraded to 1 GB of RAM. You can use two 512 MB modules then you should buy RAM from Kingston of high quality for example.

  Here is the part number for Toshiba for a 512 MB module I founded with Google:
  PA3108U - 1 M 51

  Good bye

• upgrade memory in a Portege 3410ct

  I tried installing memory of 128 MB PA3034u 3410ct, but on commissioning a message comes up saying that the ACPI BIOS is not fully compliant with the ACPI specification.
  I downloaded the latest BIOS setings but makes no difference. Will not start just yet. Clues as to correct the problem, other that not upgrading memory.

  Hello!

  This problem may occur if you add the memory (RAM) to the computer when it is in hibernation.

  When the computer comes out of hibernation mode and load the file Hiberfil.sys, Microsoft Windows detects the change in the State of the memory, and then you receive the error message.

  To resolve this issue, restart your computer.

  If the problem persists, start the computer by using an emergency boot disk, and then delete the Hiberfil.sys file.

  Good bye

• Portege 4010: How to install the cd - r or dvd - r?

  Anyone know if I can change the slimbay on my portege 4010 on a CD - R, or ideally a DVD-R?
  If so, what are the best places to get these?
  (I live in the United Kingdom)

  Thanks for your suggestions,

  Ian

  Hello

  I found the info this Portege comes with two discs. Readers are:
  Toshiba (SD-C2502) and TEAC (DV28E-B).

  I put t really know if any DVD-R/RW drive is compatible, but you can contact the Service of your country partner and ask them. They are usually updated hardware and should have enough experience.

  Otherwise, try to find a few upgrade for laptop shop in your country.

• Upgrade memory on an all in a single LX830

  I may upgrade the 4 GB provided to meet the requirements of the program. Additional memory needs to be installed in pairs? The existing 4 GB occupies a dwelling, can I mount 8 GB in another location or it will be incompatible?

  Well, mainly upgrade memory depends on the support of the chipset/CPU.

  Not quite sure what computer Toshiba LX830 do you have exactly but as far as I know the L830 all in one units would support up to 16 GB of RAM.

  A property used by a 4 GB RAM module and housing is free.
  This is why it must be able to use another additional module of 8 GB RAM.

  But of course, another module of 8 GB RAM should be compatible with the current 4 GB of RAM.
  Otherwise, you will get some compatibility issues

• Upgrade memory on NB300-108

  Looking to upgrade the RAM to 2 GB on my NB300-108

  Have you looked at the website of Toshiba and the cost, but there seems to be a plethora of alternative sites with upgrades memory compatible when I put in the part number.

  Would like to receive experiences in the forum about alternatives etc.

  Thank you

  Hello

  The laptop supports DDR2 800 MHz SO-DIMM or PC2-5300 (DDR2 667 Mhz) modules.
  These modules are provided by different companies.
  There are good quality modules and less quality modules

  Of course, you can choose and buy the cheapest, but in this case, you use the risk of compatibility problems.

  I made good experiences with RAM from Kingston. These are of good quality and not too expensive modules

• Upgrading memory on the NB550D - 11 d - 4 GB of RAM are possible

  To anyone who thinks of a memory upgrade on the NB550D:

  The NB550D supports up to 4 GB of memory, not only 2 GB as mentioned by Toshiba in their specifications.
  Upgrade memory to 2 GB is _only limited_ by the pre installed Windows 7 Starter OS, and not by the netbook itself.

  I use Linux Mint 11 Katya, 64-bit and my system works perfectly well with a 4 GB ram module. If you want to use the full support for 4 GB ram, get rid of the Win 7 Starter operating system.

  Specifications for more memory ram volume are DDR3 1333 MHz PC3-10600 SO-Dimm. I chose a 4 GB of Corsair module, because of the guarantee of 30 years of offers from Corsair.

  It took me a while to find this out hope, that this will be a help to all those who are just as secure as I was how to upgrade memory NB550D. Good luck. (o).

  Thanks for the comments

  Also it of important to mention than the 32-bit systems (not serious if its Linux or Windows) would recognize only 3.2 GB since it is a limitation of 32-bit
  So to use all of the 4 GB RAM 64-bit system is required.

• Question about upgrading memory Satellite M55-S1001

  can you please recommend what to do? I want to make my satellite m55-s1001 run faster please let me know, what do you recommend: 512 MB or 1 GB of memory? I'm not familiar with updates so please help!

  Hello

  First of all, if you want to go for fastest laptop, you should start with simple things.
  Try to defragment the disk, turn off the background process is not necessary, etc.
  Upgrade memory will the powerful laptop and of course a lot more quickly.

  To my knowledge the Satellite M55 should support the bars of memory 2 x 1024MB, and I also recommend the use of 1024MB instead of 512 MB module.

• I have iMac 5 k mid 2015 upgrading memory

  How to upgrade memory on iMac 5 k mid 2015 10.11.3 el capitan bones of 27 inches

  Installation video are visible by clicking on

  http://eShop.MacSales.com/installvideos/iMac-27-inch-5K-late-2015-memory/

• Portege 4010, HID not supported

  He finds the mouse OK but fail to complete the installation.
  I get "Human Interface Device (HID) profile is not supported in this configuration" when I try to connect my MS IntelliMouse Explorer for Bluetooth. I have the latest version of the software of Toshiba (SD) and battery on my Portege 4010. Using the USB MS Bluetooth dongle on another computer (of office) everything works fine.

  Hello

  Maybe this site will help you?

  http://APS.toshiba-tro.de/Bluetooth/

  There are troubleshooting costs and info.

  Bye Bob

• Satellite L50 - A - 1 5 PSKK6E does not start after upgrading memory

  Upgrade memory L50 - A - 1 5 pskk6e

  I have a memory ddr3 4 gb 1rx8 pc3 - 12800 S-11-12-b2 hynix and I tried to add another memory
  memory DDR3 4 gb 1rx8 hynix pc3 - 12800 S-11-11-b2, but it does not boot up the laptop.

  I tried to mount only the new but it won't start.

  Some ideas?

  I think that it s you already know that this Satellite L50 - has - 1 5 would support max 16 GB of RAM (2 x 8 GB)

  But why, box for computer laptop doesn t is very simple: the new modules are not compatible.

  I found modules recommended by Toshiba.
  These are:
  8GB DDR3L - 1600 PA5104U-1M8G
  4 GB DDR3L - 1600 PA5104U-1M4G

  Both are made of Kingston and the specifications are:

  Memory speed: 1600 Mhz PC3-12800
  Capacity: 8 GB (1x8GB module)
  Pins: 204 SODIMM
  Type of RAM: DDR3 SODIMM
  Verifying the integrity of data: non ECC
  Specifications:
  Latency (CL) CASES: 11
  Voltage: 1.35v

• Upgrade memory for Satellite 2800 400

  I am trying to upgrade my ram to 128 on the laptop. After following the instructions for the instillation, that I turned the laptop on to find that it was slower than before and that the new ram had not registered as 128, and always thought it was 64 in someone can help me solve this ir is there anything I can do?

  Hi Ben

  Maybe you used the memory modules bad.
  As far as I know that you can upgrade memory for max 192 MB
  The 64 MB has been installed in an internal memory and cannot be deleted.

  I found these compatible modules:
  PA3003U - 1 M 03 32 MB
  PS3004U - 1 M 06 64 MB
  PS3005U - 1 M 12 128 MB