Portege 7010CT shows Toshiba logo then the screen goes black

Similar Questions

• When I start my computer I saw a MSI logo and then the screen goes black and Windows does not load.

  original title: HELP ME PLEASE!

  (I am running windows xp) I need help! I tried installin linux ubuntu for netbook 10 on my msi u100, but everything was wrong when my little brother from my FlashDrive from the port, it has been installin linux from. so now when I turn on my computer it will not load windows, it will just have the msi logo and then the screen goes black and it does not load windows xp.

  Netbooks and also most computers these days, do not come with an installation CD. Instead, it has a recovery partition. Assuming that you have not deleted the recovery partition,

  Take a look at this:

  http://randompastime.blogspot.com/2010/02/restoring-MSI-wind-U100-NetBook-to.html

  Hope this helps

  Post back if necessary

  __________________________________________________________

  If this post can help solve your problem, please click the 'bookmark' or 'Yes' to this message button. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• My HP Pavilion laptop g6 hangs on the screen then the screen goes black!

  Hi, I have a laptop Hp pavilion g6 running on windows 7 that I bought for my high school diploma. Of course she had only one year warranty. At first, all was well, then he would start gel and goes black. I restored to factory settings, and everything was fine until Tuesday morning. Tuesday morning I woke up and I went to turn on my laptop after hibernating all night, as I usually do. Only instead of commissioning, he went to the logon screen and after clicking on enter my password it froze. He stayed there for a good 2 hours and then the screen went black and the small arrow white that presented themselves. After that, nothing so I turn it off and back on it. It does the same thing. Last night, after trying for several hours, I restored to factory again. This morning it worked for a few hours, then the office frozen and then the screen went black and is insensitive. Currently, it is still insensitive.

  Update: it works fine in Safe Mode.

  Hello

  303 error code is a failure of the short test (DST) disk Self and would indicate that hard is defective and must be replaced.  This also corresponds to the start-up question and would explain why you can run safe mode because the disk is under less load (that is, much less read/write requests).

  I gathered from your original post that the laptop is no longer under warranty - you can check the status of your warranty here.

  If you are out of warranty and would like a guide to replacing the hard drive yourself, please let me know - include the full model number and your notebook series g6 Nr - see here for an explanation.

  Kind regards

  DP - K

• Once I turn on my dell inspiron laptop 1545 dell logo appears and then the screen goes black

  Let me start by saying: I had similar problems before, but none of the usual works.  The other day, these two Windows Update kept popping up and wouldn't go away so I clicked finally allow.  Then the next day that I was on the internet and my computer froze, I tried to turn it off and it wouldn't if I pressed the power button until it did.  Then when I turned it back after the dell logo appeared all that I had a black screen with a cursor in the upper left.  I ran diagnostics and startup repair and nothing.  I tried to do the restore of the system once in couple with different points and nothing, I still get the black screen after dell logo.  Is there another way outside the reinstallation of the operating system, to fix (because I really don't want to lose everything I have on my computer - and no I don't save it anywhere)?

  You can reinstall the OS without formatting the drive, all of your data in a folder named windows.old. You will need the Dell Windows Vista disc however.

  Follow my guide here: http://en.community.dell.com/support-forums/software-os/w/microsoft_os/1434.aspx
  Start with step 3. (require reinstalling Dell DVD). Skip step 5 continue on step 6 to step 7. Install Service Pack 1 and Service Pack 2 (autonomous probably 32-bit) and stand-alone Internet Explorer 9. You must download these in step 4 with the system drivers as described (probably, use another computer and use a USB drive). Install the drivers as mentioned system. Activation should be useless since you use the Dell DVD in a BIOs Dell. At the stage. 12 use the automated to retrieve documents from Windows.old. Make sure you have everything and then delete windows.old.

• Satellite L500 starts, allows me to connect, and then the screen goes black

  I just bought a new Toshiba Satellite L500.

  As I am a student in high school, it was a huge and very expensive purchase for me.
  I previously had a Toshiba that served me extremely well, so I was ready to buy a new one, but now I have a problem with it.
  I have a L5000 with operating system Windows 7 Professional.

  Notepad starts end, showing the Welcome screen and allowing me to enter my password, but once the password is accepted, and disappears from the Welcome screen, I find myself with a black screen showing only my mouse pointer.

  If I enter CTRL + ALT + DELETE, the Task Manager becomes visible, but I don't see nothing else UNLESS I select 'explorer' under the processes tab and end process, then re-run the Explorer - then only the home screen becomes visible.

  It's a new laptop - Needless to say I don't want to have to do this every time I turn it on. I should try to restore factory default?
  I'm usually very proficient with computers, but I don't have enough faith to tinker with it.

  Can anyone help?

  Hi Korosuhito,
  It sounds like an infection or a misconfiguration.

  You can try to start in safe mode and search for services that run maybe you can find the "bad guy".

  or (the fastest) is to restore the factory settings
  Make sure the bios is on the 'default' as well

  I think that you have no personal data on this machine in order to recovery is the most simple and quick way!

  If the error after recovery occours made back to your dealer and get another

• my laptop starts up then the screen goes black and says no operating system found

  My child put their hands on my laptop now it starts and then it says no operating system found, or there is another sign that comes up it says

  Security Accounts Manager intiliaztionfailed because of the following error: the handle is invalid. Error status: 0xc0000008 please click ok to shut down this system and reeboot in safe mode / check the log of the events for more information

  the laptop say no operating system found is when I put the xp disk in I thought the disc would have fixed it... .as now you will probably laugh like its obveous I nothing about computers of any help would be much appreciated because it wasn't a cheap laptop and I need to keep the best care that are out of my reach of girls, but he himself is a task... Thanks in advanve david

  Please see: "operating system not found" or "Missing operating system" error message when you start your Windows XP-based computer

• At the beginning; After the Windows Logo at the start, the screen goes black and a POWER SAVE MODE comes up. I must stop button. I can run the computer as I am now in Mode safe mode with networking.

  When I turn on the computer of gateway, the machine starts and the initial window logo starts and runs for about five seconds.  Then the screen goes black instead of blue and stays black for about 10 seconds.  A 'Power SAVE MODE' appears.  The machine is dead to all orders.  I have to stop by pressing the off button.  I can turn back and the F10 key to get in Mode safe mode with networking.

  I tried to reinstall Windows XP original but it would erase my files.  I tried to restore the last good configuration also knowledge.  That did not work.

  The change came after a Windsows update.  I have McAfee security and I asked Windows but could not use due ot a conflict. -C' is all this bad start.  Clues?  I use Negear.  No change when I hooked directly either.

  Botton line, I can run in SafeMode with networking; but it is slow and I can't make alll I have to do.  What does not load Windows?

  http://wiki.answers.com/Q/How_to_get_out_of_power_save_mode_when_computer_screen_is_black

• Startup problem: first black-wallpaper appears with the logo, and then the screen goes to the Microsoft screen with green moving bar "Please wait".

  My computer is having problems loading the main office. I start it up, the first black-wallpaper with the logo is displayed, then the screen goes to the Microsoft screen with the green bar of movement. After that, the Windows logo appears and makes the sound. A new screen will appear with a "start-up Fund" and he said: "Please wait...". "This form of lasting about 5 to 8 minutes, then the text disappears, with only the bottom upward. I left it sitting there on the blank screen for about 20 minutes, and still nothing changes. I tried Ctrl + Alt + Delete, and shows nothing. Finally restart manually, but the same problem occurs. The only way that this works is in Mode safe mode with networking (which is currently used). I also tried the system restore, but this does not work because by default it must go through the same problematic steps, as mentioned previously.

  Hi ninja_panda13,
   
  -Remember to make changes to your computer after that this problem started to happen?
   
  As you are able to boot mode safe mode with networking, put your computer in a clean boot state in order to verify if any third-party application is causing this problem.
   

  Put your boot system helps determine if third-party applications or startup items are causing the problem. If so, you need to maybe contact the manufacturer of the program for updates or uninstall and reinstall the program.

  See KB Microsoft article below for more information on how to solve a problem by performing a clean boot in Windows Vista or in Windows 7:How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

• Portege R100: The screen goes black after installing SP2

  Hello
  Currently, I tried to install SP2 for my laptop (Windows XP pro) R100. The end of the installation procedure I restarted the system, as requested. The windows logo appeared, then the screen went black and the only thing I could see was the mouse cursor.

  After several reboots, the situation did not do better. I tried to go on safe mode, but I had the same (only this time the black backround was typical registration of safe mode on the sides). I will perform a system restore without having to install SP2, but the fact that I am on a DSL connection most of the time very important SP2 installation.

  I would appreciate any solution to this problem.
  Thanks for your time.

  Hello

  As far as I know sometimes a few utilities and drivers must be updated after installation of the service pack 2 Microsoft.
  On the Toshiba driver page I found a backgrounder update of Microsoft Windows XP SP2 that contains a few s information about the utilities that must be updated.

  However, additional I found a lot of new drivers for R100.
  I think you should also try to update the old drivers as driver utility and the graphics card chipset.
  Eventually, it helps.

• My computer starts and I get the Windows startup screen, then my screen goes black and the computer is frozen I guess. Stopping and restarting do not work.

  I get to the black screen with the Windows XP logo and the bar of the State, and instead of my forthcoming accounts page, the screen goes black and nothing else happens. I tried the power off to reset and restart, and I can't perform a recovery of the system with the CD.

  Hi cgrosenick,

  -What software changes you did on the computer before the show?

  Follow these steps:

  Method 1:

  Start your computer in last known good configuration mode.

  For instructions, see How to start your computer by using the last good Configuration in Windows XP functionality

   

  Method 2:

   

  Follow the steps in this article:

  Computer stops responding with a black screen when you start Windows XP

• I'm playing True Crime New York City on windows xp and every time I'm trying to play the screen goes black and then I'm back at my desk.

  Whenever I try to play True Crime New york city for windows XP it is closes its doors after the theatrics start and gives me an error saying the file d3d9.dll has stopped working or the screen goes black and then then I know you left the game back and I'm at my desk again.

  Hello Respect137, welcome.

  It would appear that running DirectX files installed on your system were corrupt. This gives a test:
  1. go to: http://www.microsoft.com/downloads/details.aspx?FamilyID=2DA43D38-DB71-4C1B-BC6A-9B6652CD92A3&displaylang=en
  2 follow the instructions which is there to install the package to update DirectX
  3. Once installed, restart your computer and try to run the game
  Let us know if this helps,
  Thank you!

  Ryan Thieman
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows Media Player play about half of the clip, then the picture cuts off, the screen goes black, but audio continues to play.

  Windows Media Player play about half of the clip, then the picture cuts off, the screen goes black, but audio continues to play.  Just reinstalled MP 11, same problem.

  Hello

  · What is the number and the model of the computer?

  · This occurs when you are working on any specific file format?

  · Were there any changes made on the computer?

  · You play the file in mode full screen?

  Change hardware acceleration

  a. you can try to change the hardware acceleration in the middle and check (you can try another level too.)

  b. right-click on a space empty on the desktop.

  c. go to the resolution of the screen.

  d. click Advanced settings, and then click the "troubleshooting."

  e. set hardware acceleration in the middle. (Here you'll get the only option your video card sound support).

  You can also check: you receive an error message of codec or audio plays video but does not play when you play media files in Windows Media Player 11: http://support.microsoft.com/kb/926373

• Whenever we start to use our computer, the screen goes black and the message 'Auto adjust is in Prgress'. Then, all of our screen is small and all the icons and pages are smaller than before.

  original title: Auto Adjust

  Hello.

  Whenever we start to use our computer, the screen goes black and the message 'Auto adjust is in Prgress'. Then, all of our screen is small and all the icons and pages are smaller than before.

  I tried restoring the system that works and that gets our screen back to normal but every day that this Auto setting is coming and we can't seem to stop it.

  Any help would be appreciated... Thank you

  Try this:

  Go to the Web site of the manufacturer of your laptop computer-graphics/computer card > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  Then:

  http://Windows.Microsoft.com/en-AU/Windows-Vista/change-screen-resolution

  Change the screen resolution

  Screen resolution refers to the clarity of the text and images on your screen. At higher resolutions, items appear sharper. They appear also smaller, so more items adapted to the screen. At lower resolutions, fewer items adapted to the screen, but they are larger and easier to see. At very low resolutions, however, images may have serrated edges.

  See you soon.

  Mick Murphy - Microsoft partner

• Satellite C660-1J2 - the screen goes black for a second

  Hey everybody.

  I recently changed my HARD drive and did a reinstall fresh, as previous was damaged. What is happening now is that whenever I have connect or disconnect the cable the screen goes black for a second. There is no real consequence of this, I'd rather just if there was an option to make it happen.

  Then, give a shout someone if you know how to deal with this.

  Hello

  > I have recently changed my HARD drive and did a reinstall of fees
  You have installed Windows from Toshiba normal Microsoft Windows disk or recovery disk?

  To me it sounds like that, you forgot to install the display driver. Also check the Manager of devices for the yellow exclamation points or unknown devices.
  Make sure that correct display driver is installed. You can download the latest version of Toshiba's official website:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  Check this box!

• Satellite L405D-11V - freezes and the screen goes black when you watch the video

  OK, so I have the Toshiba Satellite L405D-11V, I had a breakdown, basically, the computer freezes at any time and the screen would go black, with the fan and lights still ongoing, this could be at the start, or a few hours using the laptop, so I decided to ring Toshiba technology support and they arranged for my laptop to collect and be expelled for repairs.

  I was able to track repairs online via the tracking service and was able to see what they were doing to my laptop, he said that they have ordered a part, it was underway and the repairs are completed.

  However, I got the laptop back today, I turn it on, all right, I start using the cell phone that everything is fine, so I decide to watch a video on youtube, and it freezes again, so I turned off now pressed the power button, hoping he wasn't that a large, I turn back to and load the video once again it freezes and the screen goes black again, after that whenever I am watching a video or a game, it causes the computer to crash and freeze as before the repairs. So there is always a mistake, but I'm not sure what to do

  Its still under warranty, I bought the laptop from the Comet, but I really don't want to send the laptop for repairs again and find it comes back with the same fault, is it interesting sending distributed, maybe see if the comet will replace the laptop as its still less than a year to buy the laptop, or it'll just be useful to save all the hassle and buy a new laptop? If this fault happened to someone else, I could use you some help, and if someone could shed some light regarding what could be bad?

  Thank you

  Hey Buddy,

  You changed something on the configuration after you got your notebook back from repair? You update a driver, or something else?
  What operating system you use on your L405D satellite?

  To be honest it is really hard to say why it happens because technicians test to check if your laptop is running correctly.

  In my opinion you should try to update the display driver. Maybe it's the origin of the problem of s
  If this isn't the case, I recommend installing Windows from Toshiba Recovery disk to restore to factory settings. These parameters are pre-tested by Toshiba and should work.

  If you still have the problem, you must contact the technicians again. I mean you could track the online repair and according to your assignment, everything worked well during repair, so in my opinion he should t be a problem to contact guys exactly.
  Explain your very detailed problem. I think that everything can be clarified then. :)