Portege M300 and DIV port on Port Replicator 3

Similar Questions

• Portege A600-133 - Slim Port Replicator III does not entirely

  Hello...

  I just got a Slim Port Replicator III (model PA3681E-2PRP) and annexed a number of devices (a VGA monitor, a USB keyboard and a USB mouse), according to the user manual.

  The unit, however, does well with my laptop (a Portege A600-133). Specifically, the laptop battery does not, the devices are not recognized and docking led remains off. However, the laptop turns on and off of the port replicator power switch, and the ethernet port also works very well.

  Clues?

  Thank you!

  Dimitris

  Hello
  I also had problems with the Portege A600 and Slim Port Replikator, when I just connect, works all good! Maybe it's too you, when you try to connect to the port Slim R. you: with your hands the laptop with Slim Port R. extra press together in the Air about where the connector is, one when she makes "Clack" and then a right is connected!
  Sorry for my English

• Tecra M3 and Advanced Port Replicator III: not recognized as docking station

  Hello!

  Just install my new M3 and Advanced Port Replicator III. Everything works fine, but the Port Replicator is not recognized as a Docking Station (No disconnect in menu button start XP; pressing disconnect button on the Port Replicator itself has no effect either).

  Is TI WHEREAS behavior?
  Thank you in advance.

  Hello

  You reinstall the unit with the recovery CD?
  As far as I know that the TOSHIBA Mobile Extension3 for Windows XP is responsible for the good condition of the market of the docking station.
  Well, I recommend to reinstall this driver and utility.
  Perhaps the installation of the new driver will solve this problem.

  Good bye

• Portege R500 - question of Port Replicator

  I just bought a PA3603U-1PRP (mainly) to connect an external monitor, a keyboard and mouse wireless to my Portege R-500.
  Once attached to the port replicator (after startup) the HARD drive password prompt appears on the external monitor.

  However, until I get the password for HARD drive on the laptop the wireless keyboard keyboard is frozen (can not enter anything).

  Once I get the password for HARD drive on the laptop itself the external monitor, keyboard, and mouse work fine.

  Is there a setting/reason when the port replicator is attached to the laptop that I can not enter the password HARD drive on the wireless keyboard?

  Thanks in advance for your comments.

  What is the wireless dongle attached to the laptop or the rep of port?

  Try updating the BIOS R500 and the display driver. Also try reinstalling the driver of the Extensions of the Mobile or Toshiba Value Package added.

• Tecra A9 and express port replicator - two external monitors

  Hello

  I have a Toshiba Tecra A9 laptop and a Toshiba express port replicator, the Replicator has two outputs DVI & VGA, but I just can't seam to allow them both to use my funds rather than 1 desktop computer screens and the screen of the laptop.

  Is this possible?

  See you soon

  Ash.

  As far as I know that something like this is not possible. The video signal may not be spited and sent to two video output ports. If you want to use two external monitors, you need an additional video source as Toshiba Dynadock or another solution.

• Tecra A8 and Adv Port Replicator III - no audio output from the port replicator

  I have a Tecra A8 anchored on an Advanced Port Replicator III. All ports (network, USB, video) with the exception of the AUDIO ports seem to work well. I can get sound from the headphone jack on the front of the A8, but nothing since the station docking ports. Is there a docking station driver or something I need to install to get the sound from the docking station not the laptop?

  Hello

  The Advanced Port Replicator III supports the line and line port left.
  As already suggested by user above; Check if you are using the command-line output port!

  Welcome them

• Tecra M10 and Express Port Replicator, no DVI to Toshiba 20 "LCD output

  Hello

  As the bed of the subject line, I will put up a new Tecra M10 with the Express Port Replicator and monitor LCD Toshiba Tekbright 20 ".

  The system works on Windows XP, and the ordinary VGA connection on the port replicator works fine when connected to the external LCD.

  However, there seems to be no way to get the DVI interface on port replicator, working on the LCD.

  I tried to run this utility, and it does not detect the DVI monitor at all.
  http://www.entechtaiwan.com/util/moninfo.shtm

  I have updated graphics drivers Intel for XP, form the Web from Toshiba site and also have the latest version of the BIOS.

  Any ideas?

  Thank you very much
  Paul

  Hello paul

  Your Tecra M10 has DVI port?
  Replicator port is not some sort of converter and it will be just a loop through the signal directly from the laptop.
  If the computer laptop doesn t supports DVI output you cannot expect to get signal from the port replicator.

• Portege M300 and Bluetooth Nokia 6310i modem

  I have recently purchase a M300 and want to use my Nokia 6310i as a Bluetooth Modem (M300 last a Tosh Bluetooth stack etc.). The side Bluetooth works very well - phone is detected the Modem etc. - Std 33600 (Com40) is used. The log file indicates the modem commands run very well, but immediately after the ATDT numbering * a NO CARRIER response. The phone displays the correct number being composed, and I can manually dial the call of "recent" calls list.

  The same phone works very well with an old satellite pc.

  Any suggestion would be appreciated

  Bill

  Hello

  It's not easy to say why you re the connection doesn't work on your device. I also have a laptop even and it works fine.
  On the Toshiba Bluetooth compatibility list, I also noticed that the connection with a 6310i should work.
  I put t know what version of Bluetooth, you have, but the latest version is 4.00.30 form 15.02.2006

  Check out this site.
  http://APS.toshiba-tro.de/Bluetooth/

• Tecra M9 and Express Port Replicator - display flicker

  Hi guys,.

  I'm having some problems with my new Tecra M9! After that laboriously installed all the drivers and ending up with a nice clean install, I am now subject to constant headaches!

  I run a Setup dual monitor with my main monitor being a LG 19 "and the second screen being my Tosh laptop screen. When I move anything or anything open my main screen flickers like mad! I swapped the primary monitor with another screen (make and model), and it still happens! If I connect the main monitor in the laptop VGA port and run the same setting of the screen, its fine, but the second I put it through the docker it still sparkles! I also checked running a single screen (an external monitor) it still happens!

  I've updated all my drivers to the latest version without any doubt the GFX and BIOS.

  I can't be the only person having this problem, I have at least 3 of Tecra M9 who have the same problem and I can't buy laptops additional I need till remedy! Help!

  Your Andi

  Hello Andi

  Before starting any discussion can you please tell us a little more info on pre-installed OS? You wrote about installing the drivers. Why?

  As I know your laptop comes with the own operating system preinstalled. Why you do this again? And what operating system you are using?

• Advanced Port Replicator III more compatible with the Portege R200

  I just ordered a new Portege R200 and above-port replicator... However, I note that the R200 is not listed in the list of laptops supported for this Replicator! Can anyone confirm if I have made a mistake and need to change the order?

  Will be

  I visited the area Options & accessories on the European site of Toshiba, and like you said the Portégé R200 is not listed in the list of mobile phones compatible.
  So I assume that the Advanced Port Replicator III more (PA3474E-1PRP) does not support the protected R series.

• Portege M300 & Dock display probs

  I have a Portege M300 in a Port Replicator III with keyboard, mouse, network and external screen, but cannot automatically do the output to the external screen after being away with the laptop. I have to lift the lid on the laptop, login and him then use the Fn + F5 util to switch to the external display only. If I turned off the laptop but do not remove the Port Replicator and then power save it keeps in memory the output settings and Ext screen very well.

  Can anyone help?

  Steven.

  Hello

  I don t see display problems. The fact is that the laptop can't switch on the external screen after unplugging the external monitor.
  The external monitor must connect to the laptop.

• No Audio or USB ports with Port Replicator 3 and Portege R600

  I have a problem between my Port Replicator 3 (PA3681E-2PRP) and my Portege R600-13 X (Win7 Pro 32-bit). Everything has been working well for the past few months until a week ago. My PC has developed a problem then that plugged on the Port Replicator, it will not recognize something new that is connected to the USB (two PC & Replicator ones) ports, the Replicator audio output no longer works and the PC hangs during shutdown. Everything is OK with the PC when booted without the Replicator, but as soon as it is connected to the port replicator, in this case.

  I tried looking for information about this problem, but nothing helps... Any help to fix this would be greatly appreciated as it is to set up a business and I need it to work properly.

  A few things to try:

  Reinstall the Toshiba Value Added Package.
  Use system restore to restore Windows to a previous state.
  Check the connector for docking station for damage.
  Back up your data and perform the recovery.

  If its still does not, then I would send the laptop and the Port Replicator Port for an ASP for repair.

• Re: Portege R600 - port replicator is compatible with regional products?

  Community of greetings from Toshiba,

  I need to buy laptops for several employees who are moving between the United States, the United Kingdom and the Middle East.
  The Portege R600 exist in all 3 markets, but each has a slightly different part number.

  The part number Replicator of compatible Port to the R600 is difference to the United Kingdom, the United States and the Middle East.
  Users would be able to dock their laptops in one of the 3 offices, because they travel extensively between each country.

  What's the Slim Port Replicator II (PA3603U-1PRP) and Slim Port Replicator III (PA3681E-1PRP) compatible with each of the products of the soil of Portege R600?

  United Kingdom Replicator of ports Slim Portege R600-11B (PPR61E-01G00CEN) III (PA3681E-1PRP)
  Middle East Replicator of ports Slim Portege R600-10 b (PPR61E-00F00MAR) 2 (PA3603E-1PRP)
  USA, Portege R600-S4201 PPR60U - 01700C Slim Port Replicator II (PA3603U-1PRP)

  Someone has an experience buy Toshiba products in the Middle East? Or needed to use Docking Stations in offices in several countries?

  Thanks in advance,
  Ted

  (I posted a similar request in the Forum we and receives no answer - http://laptopforums.toshiba.com/t5/Port%C3%A9g%C3%A9-Laptops/Port%C3%A9g%C3%A9-R600-US-UK-Middle-East/m-p/32060#M489)

  Post edited by: TedRNelson

  Hello

  I think that it shouldn't be a problem with the different Portege R600 in combination with the Slim Port Replicator 3.

  Portege R600-11b, R600-10 b belongs to the same series (PPR61E), that the R600 US belongs to the PPR60U, but this should t be a problem.

  As far as I know the different R600 from different regions are not really different (some belongs to the same series) as far as I know there could be a difference between some pre-installed applications and some modules as for example the card wireless network, but this should not affect the use of Slim Port Replicator 3.

  Cheers mate

• Portege R500 - configure the parser on the Port Replicator

  The system is Portege R500 with a port replicator Port MS Vista running. Port replicator has a Philips 19 "LCD monitor

  System has BEEN configured so that when the system was in the duplicator monitor 19 "inches would be active and system monitor is inactive.

  But, a few days before the following events occur, when the system is in the port replicator and its turned on screen (the one with the mobile progress indicator) Windows startup is displayed on the Port Replicator monitor, then the screen turns white and displays them on the screen on the monitor system, after entering the desktop on the monitor system.

  I live in a remote area, so I can't pop in the store of the local computer to ask for help.

  I would appreciate someone to give me some guidance as to where it configures the port replicator monitor configuration. I looked at the section Configuration screen Control Panel but it seems to be the performance of two monitors, it appears not to address the peculiarities of a laptop computer with a port replicator configuration

  Thank you

  Hello

  I have no Portege R500 but I ve used external monitor connected to my Tecra duplicator.
  Can you please tell me how you have configured previously?

  What is your external monitor set as primary monitor?

• Satellite Pro A60 and Port Replicator

  I JUST BOUGHT A SATELLITE PRO A60 AND USB2 PORT REPLICATOR. WHEN I ATTACH MY LASERJET 1100 AND PRINT A TEST PAGE IT PRINTS WELL BUT IF I PRINT A WORD DOCUMENT IT RELEASED FOR EXAMPLE GOGGLEDYGOOK. CAN YOU HELP ME?

  Hello

  I understand your problem in this way.

  You have connected the printer via Port Replicator ports for the A60 SatPro.

  Œuvres driver and so on correctly because the test page can be printed. But when you want to print from Word the printer isn't or what do you mean by "GOGGLEDYGOOK".

  Could you describe a little more detailly and give us some more information like Toshiba shipped OS or MS based installation, Service Pack installed, the name of the printer and so on...

  When you want to validate this information, it would be easier to help you!

  Bob