Portege R500 and Wireless connectivity N

Similar Questions

• Portege R500 - can only connect to unprotected WLAN

  Hello everyone

  My Portege R500 (win XP pro 32) has something very strange.
  It is absolute no problems to access any unprotected WIFI, but with the gateway D - Link DI-524 in WPA - PSK / WPA2-PSK channel 6 mode.
  He faults the IP assignment many times (from 30 min to 1 hour or more), before receiving access to the local network.

  Gaeway reports: dissociated [MAC ADDRESS] with no WPA retey

  The R500 is configured exactly as all other laptops. No other laptop not a WLAN access problem, even during failures R500.

  Often the WLAN will detect R500 with the maximum power level, and after a few minutes later without WLAN is available.

  I think that there is a driver problem with WXPpro in authentication procedure:
  The WiFi network is the Intel 4965AGN
  The driver is the ver.11.1.1.16 of NETw4x32.sys

  Help me please...

  Try:

  Update the BIOS
  Update the LAN and wireless drivers
  Disable your firewall
  Use the static IP instead of DHCP
  Update the Firmware on your DLink.
  Manually configure the wireless connection, instead of by selecting it in the list and clicking "connect".

• 3g modem failure internal Portege R500 Novatel wireless

  Hello

  I have a toshiba portege r500 with windows vista business sp2.

  Since last Saturday I am unable to make a connection through the modem 3g internal 3g.

  When I open novatel wireless mobilink, he said on the radio switch sense wwan is off, however, it is not off. I can connect to the thin wireless networks.

  Toshiba broadband 3g HSDPA sm - bus modem minicards is declared as normall work in Device Manager.

  all the drivers are updated to the latest drivers. no change. Unable to use the 3g modem.

  nvtl phoenix mfc application stops working that looks like a problem of modem again.

  can someone tell what to do please?

  Did you installed the 3 G RF power control utility?

• Portege R500: unable to connect the remote DVI monitor via Dynadock

  Hello

  I just connected Dynadock (DVI) with my Portege R500. The cell would be supported - according to Toshiba - but my experience confirms that Dynadock is not able to access the DVI ports. This implies, that Dynadock is nothing more than the USB HUB.

  My setup: Vista 32 company b (CZE edition), the latest patches, Toshiba R500.

  Software: latest dynadock software 2.3 c.

  Symptom: I can't connect to the remote DVI monitor via the dynadock, there are only two external panels with 800 x 600, but Vista does not allow me to choose.

  More information: software Dynadock requires to run without Microsoft Defender, otherwise it blocks the service: DisplayLinkService; file:C:\Program Files\DisplayLink base Software\DisplayLinkService.exe
  If you turn off the MSDef, the "error 2738" message appears when you connect the dynadock and when Vista tries to install a missing drivers for you.
  Yes, I know the VBS question and the problem is not caused by VisualBasic - VBS "Hello World" runs.

  If you think always, Toshiba Dynadock is compatible with Toshiba R500, then press Fn + F5 and look at your logs and you should find something like:
  In English: igfxext.exe throws an exception 0xc000000d, offset 0x0000f9f8.

  I look forward to the comments, advice etc. If you are able to transmit this bug report to a responsible engineer, do please.

  Hello Leo

  As far as I know, Toshiba has not designed for laptops models own only Dynadock and it can be used on every laptop or fixed. Because of this, I think that this statement about model of care is not so important for this problem.

  Toshiba provides devices and software. To connect using the USB port, and these ports must each computer or laptop. I hope that you have installed the software by following the on-screen instructions (device of should not be connected to the start-up of the plant).

  Is your Portege docked the host or you have connected Dynadock directly in Portege s USB port?

• Portege R500 and Novatel Modem 3G on Windows 7

  Hello

  someone have a solution for getting the Modem 3 G build-in novatel works on Windows 7 in a Portege R500?

  I tried to install the driver for Vista 32 bit on my W7-Ultimate32bit. I have tried this driver:

  http://de.computers.Toshiba-Europe.com/innovation/Tracker.jsp?file=http%3A%2f%2fsupport1.toshiba-tro.de%2ftedd-files2%2F0%2fwmb-20071115155201.zip

  Installation starts fine, but the installer then a fallback and stops.

  What do I have to wait for a W7 driver?

  Klaus

  > Should I wait for a W7 driver?
  I think so. You can try to use the Vista driver but there is no guarantee for correct material work.
  I think that Win7 drivers will be available soon.

• Portege R500 and SSD update

  I have a Portege R500-S5006V with a 64 GB SSD installed.
  Currently I have space issues, but always so happy with this nice computer I don't want to replace it.

  Is it possible to upgrade to an SSD more? What kind of readers are compatible?
  I need to send to Toshiba, or a regular computer repair shop can do this for me?

  I think that the SSD in this machine is not a standard 2.5 "SATA or IDE Drive, it is 1.8" and has a ZIF connector and runs as an IDE device.

  Do a google search for "IDE ZIF SSD" and you will find a few commands which can be compatible. In theory, they should work in the R500, but I'm not 100% sure.

  An FSL can install for you for a fee.

• Portege R500 and Toshiba optical Tilt-Wheel Mouse

  Hello

  I have a problem with my Portege R500 combined with my Toshiba optical Tilt-Wheel Mouse. I use Win XP Pro SP2.

  When using the laptop will cut the mouse. If I plug the mouse into a different USB port, I can use the mouse for a while, but it does not stop.

  Then the same problem, but a reconnection to another work of doesn´t of USB port.
  I use the original Microsoft win xp driver.

  Hoody Bye

  Have you received the special XP driver with this mouse?
  If Yes, then install it.

  But to my knowledge it s common USB mouse that needs to use a plug n play

  Then maybe you should check the USB settings.

  Go to Device Manager and open the USB bus controller tree
  Here, you must mark the unique USB root hubs and select Properties.

  In the Management tab to disable the function allow the computer to turn off this device

  In addition I recommend upgrading the XP to the last State. I want to say that all fixes and patches must be installed!

  Good luck

• Re: Portege R500 unable to connect with Mobilink

  I am unable to make a connection using the software of Novatel Mobilink on my new R500.

  I installed * XP * and installed the relevant downloads on the Toshiba site, i.e.
  Power RF 3 G v 1.0.1.8 control utility
  MobiLink 2.0.2.1.8 v
  Wireless Broadband Mobile v 3.0.0.3

  My SIM is detected OK. I created my profile and checked that my APN, username and password are correct. When I try to connect I get the Mobilink network connection manager * error 619 * saying that perhaps my profile settings are not correct.

  However, if I create a connection by modem with exactly the same settings that the connection works fine.
  The only difference is that I use windows dial up to start the connection rather than Mobilink.

  Put Vista on the laptop the Mobilink connection works fine as well, it seems that if you want to do with XP, so I think that there could be another driver or patch required.

  Anyone had similar problems using Mobilink to initiate the connection?

  Any ideas would be welcome?

  I think it is not necessary to post twice on the same theme ;)
  http://forums.computers.Toshiba-Europe.com/forums/message.jspa?MessageID=113651#113651

• Satellite A300 and wireless connection problems

  Recently, I had to use my recovery disk and restored my laptop to factory settings. Almost everything is back is the way has been, except for a small problem.

  The WiFi does not work. It is on, but when I go to connect to the wireless family network, it tells me to insert a cable.

  My laptop is the Satellite A300 - model psagca.

  I install the drivers of Realtech and still not get the case.

  Thank you in advance.

  Your wireless network is not visible to your laptop satellite?

• Portege R700 PT310A Wireless connection of abandonment

  I just receive a R700 PT310A-05N011 and my wireless guard stall repeated.

  I updated to the latest version of the bios and checked the broadcom drivers.

  Someone at - it the same problem. I have win 7 64 bit installed

  Hi mate

  Have you noticed what Wlan dropouts using the battery power only, or do you have this problem also if the laptop is connected to the power adapter?
  I had a similar problem, Wlan, but only using the power of the battery.

  I noticed that you may change your economy option in Win 7 the power supply WLan management and this has solved the problem.

  You should try it also disable it for the Wlan to save energy and check if it would improve the performance of Wlan

• limited connection - wired and wireless connection

  all devices, but this wireless to a 3 and 2 wired connection works with router/isp

  one device gets continually unidentified network

  have tried changing ports - resetting routers and cables

  Tech ISP could not solve

  even added a wireless - device to connect netgear usb and used to connect

  He sees the network and tries to establish connection, but only gives limited connection and leave it as a network not identified on the local network connection and Wi - Fi

  ran on CMD - ADMIN MODE

  netsh winsock reset
  netsh winsock reset catalog
  ipconfig/flushdns
  ipconfig/release
  ipconfig / renew

  

  None of your answers allowed. I ended up understand mine. My avast firewall was blocking the internet. When I updated the driver for the firewall port and changed its settings, I was able to access the network again.

• Portege R500 - Novatel Wireless Radio off

  Hello

  I've seen a few posts on here suggesting various downloads and updates to solve problems with 3 G connectivity, but none of these downloads have worked for me.

  Novatel loads OK... but reports still no Service - Radio Off... I can't find a way to get "Radio on" or any info on what might be the issue...

  Any help at all would be great!

  Dave L

  Hello

  Are maybe something stupid but you sure that you have an internal 3G module?

  As far as I know not all models are equipped with this feature to check this first, please!

• Bluetooth and wireless connectivity problem.

  My laptop model Presario cq43 - 400.its runing window7 ultimate os. Although in my pc have adapter atheros wireless and according to the suggestion of hp, I've updated the partiality of f32, f33. And then install atheros bluetooth adapter SP55514.exe.from hp recomdation. But the problem remains still same.in window Mobility Center there is no option wireless and when I try to add a bluetooth device, it did not discover any device if I turn on my nokia. From my mobile when I am looking to add a device he discover user-pc but I can not pair because my pc don't response.please help me. I try many

  Hello
  Please write your product number (p/n), computer laptop which system are automatically to the help and the country of purchase.

  Resources:
  How to locate the portable computer product number (p/n)

• Acer Aspire R7 571 black screen power light on. And wireless connection to low

  I bought my laptop like 1 month ago, and after that update windows and browinsg 8.1 began very slowly, play ping games, while games I can see higher enemies, but I can't do anything for them,

  After all when I opened my laptop I have black screen nothing was only the power light was on. Somewhere to say that there is an unupdated BIOS...

  Hello...

  Try a reset of the power.

  Unplug the adapter (power cord) turned off the phone, if you have connected.
  On the underside of the laptop, you will see a hole small reset with a battery symbol.

  Please insert a thin object like a paper clip into this hole and hold for 5 seconds.

  Then plug the adapter.

  Turn on checking of the laptop in question.

• Portege R500 and Windows 7 drivers

  Some drivers W7 happened 03.09.2009 for R500 - but unfortunally the 3G a dWlan are not included. Work does'nt Insallaing Vista drivers (even in Vista mode). Can someone help me?

  Rgds
  Lars

  Hello, Lars

  What do you exactly mean with doesn t work?
  Can you activate/module 3G?
  What exactly is the problem?