Portege R930 - 4 critical events - 41 core power

Similar Questions

• Bad connection WiFi on my Portege R930-15E

  Hello

  I have a strange problem on my R930 which I tried to solve already for several months, but could not succeed.

  As I recently replaced the WLAN router and the problem remained to the laptop, I know now that it's really the Toshiba which hurts.

  Question: The WiFi is on the 2, 4 GHz WLAN and there are only two local wireless networks here in the neighborhood. The intensity of the signal is supperb (5), but the speed of the network status changes in a few seconds between the 26 and 130 MBit according to the diagnostic tool for Windows 7 (without doing anything with Notepad). I would not care about it if WiFi would work well, but it's not.

  Download videos from YouTube makes sometimes troubled (videos are stuck) but the most important problem is that access to the data to our NAS is really bad.

  I know it can work much, much better that I have also two other laptops that work well, both HP, older than 7 years, shows no such a question, signal WiFi is still at 54Mbps or, on the new, with 150 MB / sec. Other tablets and smartphones also do not have these issues.

  I tried already to have different channels, but does not help. I've updated also the WLAN, the last driver of Toshiba seems to be: Intel Centrino Advanced - N 6235 Version 13.03.2012 15.1.0.21. Is this really the last being?

  In addition, I found around many problems of WiFi in the Toshiba Internet, but so far, none really match my situation.

  But I found that Toshiba seems to have bad WiFi antenna, but I sat just 5 meters from the router, so I don't think that it's a software problem (driver). Operating system is Windows 7 Professional 64 bit.

  Do you have recommendations for me what to do?

  Thank you

  Volker

  Hello
  Indeed, Portege R930-15E was equipped with the Intel Centrino Advanced-N 6235 WLan/BT combo card that supports the 802.11 A/G/N standards.

  The latest driver should be available on the Intel page:
  http://www.Intel.com/p/en_US/support/highlights/wireless/can-6235

  It seems that the latest driver (at that time) was published at 29/12/2014 and its v15.14.0.1 for Windows 8.1
  Anyway, as you can see, this WLan module supports the 802.11A/G/N standards.

  I think you should check in the Device Manager-> properties-> Advanced tab WLan card which WLan standard was chosen. Probably, you could change cela a/g or just N

  Last but not least, I would recommend allows you to check the WLan Card power saving option.
  Option for WLan module energy savings are in the advanced power settings and I recommend you to choose for two profiles (dough/adapter) the performance of the value

• Can CPU overheating if Portege R930 goes into sleep mode?

  I have an a Portege R930. I run an application of 25-30% of the CPU for long hours. If I put the laptop in mode 'sleep', the calculation get suspended? If not, and it is still running, how the CPU is cooled when the fan is off mode 'sleep'? The CPU can overheat?

  I * don't * want my program from several hours to be interrupted by a detector from overheating. If I know that the program is suspended in mode 'sleep', I fear enter "standby" mode. If this isn't the case, so I'll keep the laptop awake, and if I need to carry the laptop, I'll put it into hibernation.

  The answer seems to be that the CPU cannot fire because the programs are suspended: http://forums.toshiba.com/t5/Port%C3...p/689961#M4014

• Portege R930 - 14 X and additional software

  Hello

  I recently acquired a Toshiba Portege R930 - 14 X, a friend. It is running Windows Pro 8.1, it came with any disks etc. It does not seem to have any of the supplied software, he would come with out of the box. Please excuse that my ignorance, but is there anyway I can restore it or download it please.

  Thank you very much

  Hello

  According to the specifications of the laptop this model of laptop computer came with preinstalled WIN7 64 bit PRO & WIN8 64 bit PRO DVD.
  http://www.Toshiba.co.UK/discontinue...Tege-r930-14x/

  I don't know what version of the OS is installed now, I mean is it original with update or install own Win8.1 Win8 but all drivers necessary, tools and utilities, you can download from Toshiba support and download page - http://www.toshiba.eu/innovation/dow...ivers_bios.jsp

  Additional software is included in the recovery image only.

  If you have any other questions please be free to ask.

• RAM in Portege R930 max

  If I understand the straight plug to the Portege R930 with i7 processor maximum RAM is 8 GB. Has anyone tested a larger memory to say 16 GB?

  / Anders

  What model do you have? At your Portege PT331E part number?

• Portege R930 - upgrade the mSATA SSD succssfull

  Just briefly, I wanted to report an SSD upgrade.

  When I got my Portege R930 (PT331E, i7) two years ago, I changed the HD to a PRO 840 Samsung SSD 512 GB (big improvement). Now, this SSD is too small (photos!) and I wanted to increase the capacity up to 1 TB.

  But instead of a new SATA, I decided to go for an mSATA + adapter SATA I felt an mSATA unit would be more "evolutionary" - next update of the laptop for me would be a Portege Z, who use mSATA.

  So I bought a Samsung 850 EVO 1 TB with a Delock adapter/converter mSATA SSD, made a clone of the Apricorn cable and the software switched the SSD and everything works fine (actually a little faster )! At first I tried to use the clone with software from Samsungs migration but this didn t work, maybe I didn t the right version.

  -Now I have a lager SSD that will live longer than my R930. Please note that I'm not an expert with computers - just a happy user Toshiba! Thanks for a good forum with my good ideas!

  Concerning
  / Anders

  So, I bought a Samsung SSD 850 EVO mSATA 1 TB whole with a converter/adapter Delock...
  .. .and everything works fine

  Good news Lao!
  Thanks a lot for the comments...

  I also upgraded my laptop with a 250 GB SSD drive and now I think of a larger SSD... I should consider your solution now...

• Portege R930 gets hot enough

  My Portege R930 (PT331E - i7) becomes quite warm today, earlier it was very silent, now the fan is 70% most of the time.

  I open the bottom cover and checked the cooling paste on top of the processor - seemed rather dry.

  Should I change the dough? I cleaned the fan.
  What can I do else?

  Thank you
  / Anders

  Hello

  If you have already removed your laptop and cleaned vents and grid cooling cooling you can also change the FAT if you know how to do this. I mean, why not. Laptop is already open.

  Usually after the computer cooling system laptop cleaning should work a lot quieter. A few years ago I did this on my machine. I found so much dust inside which blocked the air flow.

• Portege R930 brightness increases when the shiny things are displayed

  I use a Portege R930 with the 2nd lowest brightness. I noticed that when something bright is displayed, the overall screen brightness adjusted upwards by about 5 tiny slices to speed increment of 1 / second.

  Increments of brightness are not nearly as pronounced as the steps in the brightness slider, but it's there. And very annoying.
  I can't find any mention of this 'feature' online. Is it possible to disable it?

  Hello

  I put t know if your laptop was equipped with the graphics card AMD but the problem, you take it all sounds a bit like a future provided by AMD GPU called: AMD vari-bright.
  Vari-bright save energy consumption by optimising contrast image on the internal LCD screen AMD computers.

  This feature can be used if the computer is running in battery mode, using the internal LCD only or PowerPlay settings under mode battery is set to maximize autonomy.

  The Vari-Bright feature can be turned on and off in CCC.

• Portege R930 - 1 d 0 + Replicator port dual monitor supported high speed II - taken

  Hello

  Crossing a Portege R930 - 1 d 0 high speed port replicatior II.
  Is it possible to dual-display output?

  Thank you

  You hear the internal + external display by the dual display or you mean two external monitors?
  Speed Hi II port replicator supports the RGB port and display port and HDMI port but (display port and HDMI) can not be used simultaneously.

  You can use the internal s for computer laptop HDMI port and for example a the Hi speed port replicator II ports to connect an external monitor.

• Portege R930 is compatible with Dynadock U3.0

  Hello

  I m using a Portege R930 with a ' Toshiba Hi Speed Port Replicator II.
  The dock works fine, most of the time, but I was wondering if R930 is also compatible with Toshiba dynadock U3.0 USB 3.0 Docking Station universal since I want to use the laptop monitor and 2 additional monitors(1920x1080).

  Best regards
  Adrian Dobre

  The Dynadock U3 is compatible with most computers and could be connected to a regular USB port.

  It supports separate chip graphic.

  It supports a HDMI and a DVI - I ports that can be used simultaneously.

  This support allows to use up to 3 monitors (2 external + 1 internal)

• Portege R930-C086 - how to recover the Windows 8 serial key?

  I have Toshiba Portege R930-C086

  my hard drive is broken, I lost all my data and the original windows 8
  so I want to buy the new HDD, and I want to know how I got my windows 8 key back?

  I don't want to buy the new windows 8.

  Each laptop comes with preinstalled operating system also preinstalled recovery media Creator called tool. This tool can be used to create bootable recovery DVD or USB media. This recovery media can be used in case this recovery HARD drive installation procedure no longer works or if the HARD disk fails, as in your case.

  I presume you didn't create this media, right?
  Is that you can order the original recovery image but is not free.
  More information, you can get the Toshiba service provider in your country.

  I don't know if you can order it on https://backupmedia.toshiba.eu/landing.aspx but please check.

• error 0xc004e003 during activation of Win 7 Pro on Portege R930 - 17 L

  Toshiba Portege R930 - 17L
  S/N: 5D016093H
  (If I search on Toshiba after SN I only find in Toshiba - Ukraine)

  Bought at the shop online "Sigmanet" in Romania.

  It has a sticker on the back w / Windows 8 Pro (small sticker without product key).
  He arrived with the installation of Windows 8 CD.
  Now, it has been pre-installed Windows 7 Pro x 64 SP1 (this laptop has the right of use of Windows 8 and Windows 7)
  Of course, the preinstalled operating system has been slow and gave errors (pre-installed McAfee antivirus, a bunch of small apps, a.s.o.)

  I reinstalled Windows 7 Pro SP1 x 64 (original CD) on a clean partition.
  I can't activate it with the following text:
  Product key: XXXXX-YYYYY-ZZZZZ-XXXXX-YYYYY
  Product ID: xxxxx-OEM-xxxxxxx-xxxxx
  Error code: 0xc004e003

  Now, I spoke with the Microsoft Romania, they tried to help me, but they failed.
  They told me that the license seems stuck at Toshiba, so they suggested to speak to them (Toshiba) to unlock the license or provide a new product key.

  So, I contacted the seller. They passed me at the service of Toshiba authorized in Romania which avoids to help me.

  Now I'm stuck. What to do or who to contact. Everything is so blurry...

  I appreciate any response you can give me. Thank you!

  > It has a sticker on the back w / Windows 8 Pro (small sticker without product key).
  > Happened with Windows 8 installation CD.
  > Now it was preinstalled Windows 7 Pro x 64 SP1 (this laptop has the right of use of Windows 8 and Windows 7)

  Laptop Toshiba computers are preinstalled with Windows systems that are already activated.
  The stickers that you will find at the bottom of the units are the serial OEM key and these keys don't work in relation to other different systems. The OEM key belongs to the preinstalled image.

  So in case you would use the Toshiba Recovery disk and install Windows system using this disk, the serial key is not necessary.

  According to the technical specifications of Toshiba:
  http://www.Toshiba.co.il/en/laptops/Portege/r930/Portege-r930-17L/ the laptop has been pre-installed with Windows 7 Pro 64 bit.

  This means that Win 7 Recovery DVD was not part of the package. Why?
  because the Toshiba Recovery Media Creator software has been pre-installed on this laptop. The software allows you to create the recovery DVDs containing Pro Win 7 64-bit system and the image that is activated.

• Portege R930 - 15G - lack of security of Toshiba Assist Module

  On my new Toshiba Portege R930 - 15G I can't call the "Toshiba Assist security" module and only get the message 'a required module is not installed.

  If a Toshiba support person is reading this forum, I would be very happy to get a hint of what source I was able to download the required installation files.

  Maybe someone else has an idea how to solve the problem.

  Andreas

  > I can't call the "Toshiba security Assist.
  Can you please tell us how do you do that? Are you using the original preinstalled OS or the clean version?

  On the Toshiba download page, you can find this tool, version 2.0.9. try to download and install it.

• Portege R930: Low voltage DDR3-1600 SDRAM (1.35) or standard voltage 1.5

  Hi again,

  I just wanted to know if the two kinds of SDRAM DDR3-1600 Rams (one is called memory low voltage) which are available on the market are compatible with my Toshiba Portege R930 i7?

  Thank you!!
  Concerning
  / Anders

  The detailed specifications of the compatible modules are:
  + DDR3-1600 PC3-12800, SODIMM 204p, 1.5V +.

  As you can see its standard voltage of 1, 5V

• Portege R930: cannot use the keys FN under Win XP

  Hye

  I'm French. I'm sorry, but my English is not good. I'll try to explain my problem

  Yesterday, my boss gave me a new computer. It's a PT330E Portege R930-1FE with windows XP, 7 has been uninstalled

  I can't turn off my touchpad. I can't use the Fn key.

  I called technical support and after I downloaded the drivers for seven 32-bit and 64-bit... But I still have my problem

  Please, you have a solution.

  Thank you

  Hello

  Fn keys are controlled by special tools of Toshiba and depends on the running system.

  Using Win XP, you need to install the common Modules and this must be done first. The common modules is an essential component of Windows systems.
  He will perform the other original programming from TOSHIBA to work properly.

  Check this box:
  [Common Module Win XP v6.07.03 | http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 4 & selSeries = 151 & selProduct 7565 = & selSh ortMod = null & language = 13 & selOS = 10 & selType = all & yearu pload = & monthupload = & dayupload = & useDate = null & mode = a llMachines & search = & action = search & macId = & country = al l & selectedLanguage = 13 & type = all & page = 1 & ID = 83752 & OSI D = 10 & driverLanguage = 42]

  To get the other buttons FN working (ie the screen switching output), you must install hotkey utilities for display devices
  [Utility Hotkey for display v1.0.2.5 for Win XP | http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 4 & selSeries = 151 & selProduct 7565 = & selSh ortMod = null & language = 13 & selOS = 10 & selType = all & yearu pload = & monthupload = & dayupload = & useDate = null & mode = a llMachines & search = & action = search & macId = & country = al l & selectedLanguage = 13 & type = all & page = 2 & ID = 83758 & OSI D = 10 & driverLanguage = 42]

  In order to disable the touchpad, you need to install Touch Pad on / off Utility
  [Touch Pad on / off Utility for Win XP v2.5.5.1 | http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 4 & selSeries = 151 & selProduct 7565 = & selSh ortMod = null & language = 13 & selOS = 10 & selType = all & yearu pload = & monthupload = & dayupload = & useDate = null & mode = a llMachines & search = & action = search & macId = & country = al l & selectedLanguage = 13 & type = all & page = 3 & ID = 83770 & OSI D = 10 & driverLanguage = 42]

  I recommend you to check the page of the Toshiba UE driver and install all the available drivers for Win XP.