Ports for Essbase

Similar Questions

• Tomact as an application server for Essbase 11.1.1

  Dear all,
  
  The management decided to move our IBM Websphere 6 application (Web server) server to Tomcat to the cost-effectiveness.
  
  I've nt used Tomcat as Web front server and I appreciate if you can share your experience or any documentation that helps me integrate Tomcat as the Web server for Essbase 11.1.1
  
  for the most part, I'd be interested to know the required port number and artifacts (war files) necessary.
  
  Thanks in advance
  
  See you soon
  MS

  876035 wrote:
  Yes, I had a look at the EPM cumulative System Feature Overview Tool ID 1092114.1. Unfortunately, the comparison stops with 11.1.1.3 in the selection of TARGET output.
  and this ID seems to be later.

  I think you look the wrong file, if you look at epm_sys_cfo_tool.xls then the igoes target up to the latest version

  See you soon

  John
  http://John-Goodwin.blogspot.com/

• I just bought a keybboard ultra thin logitech for iPad air. It has a port for a small cable, but no cable in the box. What is the port for, and what don't get me?

  I just bought a keybboard ultra thin logitech for iPad air. It has a port for a small cable, but no cable in the box. What is the port for, and what don't get me?

  Have you tried the Logitech support site?

• Satellite T130 - 10G: extra port for mini SSD?

  Hi there :)

  I found an empty port in my T130, near the port of hard drive, see also here-> [klick | http://www11.pic-upload.de/08.07.14/3aosd93avlc5.jpg]

  It's a job mSATA-Port for mini-SSD as "ADATA SX300 mSATA SSD 128 GB"
  so I can use both, _and_ SSD HARD drive? *

  Thank you

  (* for example: Partition boot and Windows: SSD, data partitions: HARD drive)

  Hello

  I'm quite sure this isn t mSATA and this series doesn't support the mSATA SSD definitely m.

  Fact is that belonging to the same series models support different hardware specifications.
  For example: some models have been fitted with one: module 3G miniPCI and module Bluetooth Mini-PCI and some models supported only the miniPCI WiFi card.

• WSD port for printers and TCP/IP ports monitor, what is the difference?

  There are a lot of discussions on IP etc. addresses for printer problems. There is no mention of a new feature for the port for printers, WSD port for plug-and-play printers, I assume that the IP addresses have no importance with WSD, my printer is vaguely configured for the WSD port and TCP/IP port, can someone please expain

  Here is a description I found

  The WSD Port Monitor is a new printer port monitor in Windows Vista and Windows Server 2008.  This port monitor supports printing on network devices that are designed to include Web Services for devices (WSD) technology.  Services Web for devices allows devices connected to the IP-based network announce their functionality and to provide these services to customers using the Web Services Protocol.  Clients and devices WSD communicate on the network using a series of SOAP (Simple Object Access Protocol) messages on UDP and HTTP (S).  WSD for devices offers a plug-and-play network experience that is similar to the installation of a USB device.  Services Web for devices also defines a security profile that can be extended to provide additional protection and authentication by using certificates based on the device.

  WSD is not a port, but a port monitor.  A port monitor looks at information from the TCP/IP port and makes routing or changes based on what happens in the port.

  This link has some in the description of the depth of the WSD port monitor:

  http://blogs.technet.com/b/askperf/archive/2008/02/11/WS2008-the-WSD-port-monitor.aspx

  Back to the comparison of the IP address as a P.O. box.  Once the letter arrives in the POST box, someone needs to come empty the box or letters are going no where.

  When the data comes in the TCP/IP port a port monitor is where I look for that to happen.  The WSD port monitor would take over this function from the standard TCP/IP port monitor.

• HP - 15 af008ax: my new laptop usb port for the left side does not, only 1 work on 3 Please help me

  My new laptop usb port for the left side does not, only 1 work on 3 Please help me

  Hello:

  Have you installed the drivers for W7 32 bit amd chipset?

  If this isn't the case, you must install them and reboot the PC to get the 3 for usb ports work.

  You want the first file on the Web page.

  http://support.AMD.com/en-us/download/chipset?OS=Windows%207%20-%2032

• Using the Serial Port for data acquisition Non-Serial

  I searched the forums and can't find anything on this topic.

  I saw that it was possible to use the parallel port for e/s digital single and I was hoping that the serial port can be configured the same. It seems all VI VISA only to use the serial port to receive ASCII characters at a given flow rate, but is it possible to simply query the status of the line series at my own speed to see if it is high or low, kind of like a single pin DAQ?

  It seems that it would be possible until the serial data are read and controlled by labview, not Windows. Let me know if you have ideas of how to approach this problem, or any comment as to why it is not possible.

  Thank you all!

  Select the property > settings series > Modem of the line parameters. For example, the State of the CTS is an entry to the pc.

  With the help of these lines is a very poor substitute for a scope or map DAQ. The only things you can return is Asserted, Unknown or Unasserted. The range of acceptable signals is important enough. Anything between + 3 and -3 is an unknown state. Your other signals is + / 3 to 15 volts. What type of signals do you really want to capture?

  Edit: there is no such thing as a visa so I have no idea of what you actually use.

• Set the port for WMI for Windows Server Standard Edition 2003 R2

  Hi guys,.

  Can I know how to solve a static port for WMI using Windows Server Standard Edition 2003 R2?

  Thanks in advance!

  Ask in the forum Windows Server:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• How to enable access to a port for my mobile phone application to access. When I try to connect I get error socket is closed.

  I have purchaced an app for my phone android mobile facenate which can access my computer remotely.  When this trys remote app to connect to my computer, I receive an error message that says the socket is closed.  What I need to know, is how to open a port for this app to access my computer.  Also I got an error that I do not have a public IPV4address that may have something to do with it.  I have win 7 64 bit. I would be so happy if someone could help me; I'm really ready to see this app works.

  Hello

  I suggest you follow the steps in the link below and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows7/allow-remote-desktop-connections-from-outside-your-home-network

• Port for uTorrent - WRT54GC

  Hello

  I need further assistance.

  I want to free ports for uTorrent.

  I have a router WRT54GC.

  I successfully logged in and clicked on Applications and games, and I think that there should I typed port in tab Port range forwarding.

  Given that I'm not good at this stuff, and it's my first time there is. I want to know what are the beginning and end for uTorrent port numbers, or where I can find it. I have uTorrent 2.0.3 and I found the current port (for inbound connections) in the installation guide. In the preferences and besides I can't find nothing with 'port' in it.

  As for the Protocol, I would (TCP and UDP), the IP address is the same and will check Enabled. Only, I don't know the start and end port.

  Thank you further and I appreciate the help!

  Thank you

  ALEKS

  I solved it ^^

• USB 0001 virtual port for UsB not found

  When inatalling a Xerox Phaser 8560DN to my laptop HP Win 7 professinal it does not find the virtual USB 0001 port for UsB. I installed the printer even to other laptops and no prblem. When you come to select the port the virtual prot is tehre but not so much in this laptop and HP peole say it is not their problem. Any suggestions on what to do?

  Hello

  You don't see any other virtual ports except USB 0001?

  Follow these steps and check if that helps:

  1. go in Control Panel.
  2 Select all Control Panel items.
  3. open devices and printers.
  4. at the top of the window, select Add a printer.
  5. Select Add a local printer.
  6. If you want to choose a Printer Port, select use an existing port.
  7. in the drop-down list, select USB001 or USB0002 (virtual printer to USB Port).
  8. Select the next button.
  9. in the manufacturers section, select HP.
  10. in the printers section, search for your printer model and select it.

  Note: If your printer does not appear in the list of HP, select nearest LaserJet series model number.

  Click the Windows Update button. WU get the database driver for all HP printers.

  Note: the search may take a while.

  When the search is complete, go back to the HP section and your printer should now appear there. Select it and click the next button.

  Your printer appears in the printer name box, click Next again and the printer will be installed.

  Kind regards
  Amal-Microsoft Support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How to open the manual mini port for vpn connection in win7?

  How to open the manual mini port for vpn connection in win7?

  Hi Andrew,

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It would be better suited to the TechNet community.

  Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

• Change the default ports for http and https

  Hello

  I'm trying to change the default ports for http and https

  I have a 506th PIX (which does NOT of NAT)

  I have the following: -.

  static (inside, outside) tcp 192.168.10.2 601 192.168.10.2 http netmask 255.255.255.255 0 0

  static (inside, outside) tcp 192.168.10.2 602 192.168.10.2 443 netmask 255.255.255.255 0 0

  access-list acl permit tcp any 192.168.10.2 eq 601

  access-list acl permit tcp any 192.168.10.2 eq 602

  Access-group acl in interface outside

  where 601 and 602 are the http port and https to be redirect to respectively.

  I changed the webserver accordingly

  I get the error message

  "No group of translation not found for tcp src outside:189.x.x.x/50232 dst inside:192.x.x.x/80" (trying to access port 80)

  "I also have ' fixup protocol http 601.

  I had access to the internal and external web server before attempting to change the default ports

  Any ideas where I'm wrong?

  See you soon.

  I apologise for not thinking correctly.

  the static method must be:

  static (inside, outside) tcp 192.168.10.2 80 192.168.10.2 601 netmask 255.255.255.255 0 0

  static (inside, outside) 192.168.10.2 tcp 443 192.168.10.2 602 netmask 255.255.255.255 0 0

• RJ-45 (LAN) and port the expansion Port for laptop

  I am a newbie. I have a HP Mini Netbook 1151NR. Someone can tell me what and where can I find the Port RJ - 45 (LAN) and the expansion Port for laptop? What is it like? How can I use them?

  PindarDraconia wrote:
  I am a newbie. I have a HP Mini Netbook 1151NR. Someone can tell me what and where can I find the Port RJ - 45 (LAN) and the expansion Port for laptop? What is it like? How can I use them?

  

  The expansion port is used when connecting to a docking station... and it's the rectangular port next to the ethernet port.

• Highway X8.2.2, Changing default SIP Port for B2B calls is not possible

  Much of community support.

  I 10.5.1 (SU1) of CUCM and X8.2.2 Expressway.

  I have configured without VPN Jabber and B2B based on the Document calls "CVD-CollabEdgeUsingBE6000 - Apr14.pdf.

  everything worked fine for months, but after the upgrade of the X8.2.2 Express way B2B calls are no more work.

  After troubleshooting, I found the following:

  the DSF Guide tells me to change the default Port to 5061 to 5560 B2B calls because 5061 is also used for the integration of Jabber.

  When I look at my record of wirekshark I see cucm tries to connect to the port 5560 expressway, but after sending a SYN packet, cucm receives a RST packet.

  When I change back to the port of 5560 to 5061, everything works well again for B2B, but of course encrypted calls Jabber connection is not possible more.

  for me, it looks like a bug, but I found nothing on the 'Bug search' tool.

  I also tried to disable all Protection rules and I also have a firewall rule for Port 5560. I also tried to change the TCP Port to something different, 3999 for example. All this without success.

  Just a little look in the guide.

  Two caveats. First thing the guide explains unencrypted SIP - TCP connections, if you want to be aware that both sides use TCP or TLS. If you are using TLS certificates must be good as well.

  5560 isn't a port on the highway, this is the port for the trunk on CUCM.

  What do you see CUCM sending to Highway: 5560 Setup is not ok.

  The port of the highway will not be changed.

  If you look at page 30, he 5560 port is used for the "incoming Port *" and the bottom of page 31

  You can see that it uses the Expressway IP with port 5060.

  On the highway, you configure the area to port 5560 (page 34)

  And of course the firewall should also be ok.

  Please note messages posted under the stars below and set the thread if it's an answer!