Postazioni Xp con uso Esxi USB e the solution?

Similar Questions

• ESXi USB, what happens if you then remove the USB boot?

  Hello

  Someone in our team IT wants to use ESXi 5 bootable, i.e. start an ESXi host for a 2 GB USB flash drive in order to save the cost of buying the hard drives local to a RAID set.

  I know there are a few downsides to this, but one thing I wanted to know more precisely, it is what happens to the ESXi if you remove the USB or the USB drive goes down, while the host is running. The army continues to operate, as it will be charged the ESXi image in memory? Or it will fail if it cannot see the USB as it initialized from?

  Thank you!

  ESXi will work on - running some virtual machines are not affected.

  Usually, there should be no problem to plug new - but I have seen cases where the system does not start after a rough unplug - so avoid it.

• [not resolved] At boot esxi USB key, but the key is broken, how to recover?

  Hi all

  I installed a host vmware esxi 3.5 starts using a USB key.

  My problem is that the key has been broken.

  I have reinstall a new key with the same version of esxi 3.5 and assigned the same IP address to the host.

  Should what steps I follow to host my comments towards the top and run again?

  Thanks a lot for your help.

  It's not good

  Are you sure that your storage space is not the original problem?

  If you start from USB, and the key fails, ESXi will continue to function until you restart the box. ESXi RAM tracks

  If your storage space is 100%, you can try the following

  Advanced settings under configuration if I remember correct:

  EnableResignature change to 0

  Replace disallowSnapshotLun with 0 as well.

  A new analysis of the storage card at least 2 times

  Change the values back to 1 if it works

  Concerning

  If you find this or any other answer useful please consider giving points by checking the answer useful or appropriate. Thank you.

• Problems with the data store when installting ESXi USB

  I had problems getting free ESXi reliable running.  I am able to install a flash drive fine and initially everything works and I am able to create virtual machines.  Upon the first connection to vSphere, told me that there is no data store, so I create one on my controller LSI 400 GB RAID1 8308elp without problem.  However, once I reboot the server ESXi I lose the data store.  When I check my warehouses under Configuration it is listed.  At this point, if I try to create the data store, yet once I get "Error during the configuration of the host".  I read about using fdisk from the console when people have had this problem but there is no access console in the free version.  Is that what I can do to work around this problem?

  Right in the HCL... SAS/SATA-RAID of the lists for older versions, SCSI for the current version... Search within i/o devices for "LSI 8308elp '...

  VMware VCP4

  Review the allocation of points for "useful" or "right" answers.

• iPhone 5 c will not charge via USB on the laptop?

  Hi all.

  I have an iPhone 5 c and as about a week ago, does not charge via the USB port on my laptop. He sees very well in my wall sockets and Sockets USB as well, but not in my laptop. I have an Acer laptop running Windows 7. Windows is up to date, iTunes has the latest version installed. Whenever I plug in my phone, one of the following conditions occurs:

  (1) does not have

  (2) noise "plugged" USB lights, the window on the lower right, tell that a USB device has malfunctioned

  (3) (rarely) of phone calls after I tried several things

  What happened is I would plug my phone, she would charge via USB, iTunes opens automatically, and "trust to this computer" popup would come on my phone if I had unlocked it. None of this is happening now. I did the following to try to remedy:

  (1) power cord iPhone replaced (it was time for a new anyway)

  (2) uninstalled and reinstalled iTunes

  (3) restart computer and phone probably 29856 times

  (4) device Manager... nothing comes up at all, not even the unknown device. RARELY the unknown device comes up, then I get a "Code 10: this device cannot start" error, but it is * in a handbasket just trying to get to THIS point! and IF I do what they say to do to correct a code 10 (uninstall all USB and restart the computer, then USB devices hook to the top one at a time), so I'm now at my problem of a communication that don't meet pluse between my phone and PC

  5) tried to the registry editor, but not "upper filters" option rises

  (6) virtually every other option on this thread of 5 pages iphone not recognized by Windows 7

  Help, please?

  The USB port of your laptop does not provide sufficient power to recharge the phone. It is a hardware problem with your laptop, not the phone.

• Cannot start OSs of HDD external USB on the Satellite NB10t-A-101

  I'm unable to install Linux on the Satellite NB10t-A-101, because it does not allow to boot from USB or install other OSs.I tried to circumvent this way: (it came with pre-installed Windows 8).

  (1) turning off SecureBoot (which I did)
  (2) putting USB at the top of the list of starting the computer.

  But it does not work.

  I have two HDD USB (a TPG, the other normal) partitioned and it s impossible for them starting with this model of Satellite. I m thinking to return it back to the store that I need to install/start several OSs.

  Hello

  Great that you are using Linux on your PC!

  You mention that you have disabled the secure boot.
  It is very good. But you don't say anything about the startup mode and nothing about what Linux you try to start.

  Most of the distros must support UEFI but that can't be true for each of them.
  If you want Win8 dualboot with a Linux distro, so you need to active UEFI and able to start in this mode distribution.
  If you use a late clone-Ubuntu, Fedora or OpenSuse, you should be fine!

  Another clue could be to take the USB key and try to start another PC from him.
  Which will give a clearer picture of where the problem lies: on your key or the compatibility of firmware NB10 & distro Linux of your choice.

  If you try to boot from a USB - HDD, I'm afraid I'm a bit at a loss as I've never tested.

  I hope this helps!

  Tom BR

• I have a late 2009 iMac. When I tried to upgrade to El Capitan. He said that the CHIP shows the h/d is a failure and can not be updated. I have install an external withEl of h/d Cap but it is very slow. the h/d is USB 3 but the iMac's USB 2. the h/d is on

  I have a late 2009 iMac. When I tried to upgrade to El Capitan. He said that the CHIP shows the h/d is a failure and can not be updated. I have install an external withEl of h/d Cap but it is very slow. the h/d is USB 3 but the iMac's USB 2. the h/d is only 5400 RPM. a 7200 RPM 7 / would accelerate the iMac?

  No, because the limiting factor is the computer is USB 2.0, which is how it connects any external drive apart the external drive. As USB 2.0 is much slower, there is no real advantage to a 7200 RPM drive. What you need is a Firewire enclosure that supports FW800 which is much faster than USB 2.0.

• A key using self-powered USB causes the base station go "off-line".

  I found that by using a USB drive self-powered, as the WD My Passport, without a USB powered, hub attached to the base of the station USB port has caused the base station go "off-line". In fact, using a powered hub does not always remedy the situation, but it is more reproducible without one.

  This is true for the AirPort Extreme and Time Capsule 802.11ac. The problem does not occur immediately, but it may happen over several days. The symptom is that the player is no longer lies in the Finder, or the base station appears in AirPort Utility.

  My question is if others have had the same results? ... and did you find permanent solutions?

  

  USB key "seems" less reliable on the airports of AC model than on previous versions.

  I tend to not use USB attached to routers because I think it's convenient mediocre and poor speeds. But I tested with previous models, and it seems ok...

  KT those a few posts here a me trial there. These are not self powered readers... who I have long recommended people avoid the use (without a powered hub)...

  Re: External backup drive down regularly

  In fact, the wire is different from what I remember... Age don't you know.

  But I did the test on an AC TC. The result has been very reliable. He did not cause the TC to close... but I lost the connection of the USB almost every day... except for a trial where I kept the USB drive mounted in the Finder... so that the USB drive wouldn't turn it down. He then worked for a few weeks... until what the noise of rotation of disk (sitting next to me) drove me crazy... as soon as he was mounted is more, he would pass the same existence as before.

  The previous model TC was barely big enough for the internal use of the power supply units. So powered car running disc was impossible.

  Provide EI (GEN 1-5) at 1. 8A and 12v was adequate, but the standard USB port is estimated at 500 my wrong to manage disks free power.

  You would certainly think AC 12v 5A power supply models would have a lot of power. Yet, power problems are a major problem still. Supply is extremely sensitive and stop easily for reasons I'm still to understand.

  Where the long threads on power issues to the AE.

  Now, I'm going to speculate... I think that SOME problems are associated with power.

  What is the USB port side in airports of AC? Is it still 500ma? Apple never seem to give easy to find info on these details.

  Do you know? I haven't measured it, but I can try timing the time it takes to charge a phone.  Assuming that it will immediately trigger.

  Then he will have problems with a self-powered drive. Even if the drive has less energy than quotes, current during starting is much higher. The restriction of the power on the USB port is managed by a self regulator recovery... Once you triggered it, you must stop the power... then reboot the machine to restore power.

  Then, I also did the test with hub powered... and like your results... It was better. Longer time between the drive disappears from the network. But it was not enough to stop it.

  There is another interesting effect using self-powered hubs... I discovered this on a computer running Mac OS lets say! The computer would not start with a powered hub connected to the front USB. Hubs self-powered cheap, showing a defect in their design. They can refer to the USB port. In this computer, it was enough to stumble on the good power circuit and prevent the supply, commissioning... As long as the computer is running, everything was fine... but if I turned off it would not start. I finally woke up I had to exit the USB every time. At one point, I made a "special" Cup USB cable 5v line so the hub can stay connected. You can probably just to isolate the 5v of contact in the USB. Regardless of the configuration of power USB in the AE or TC is as you can assume she's sensitive enough... and at any time when the 5V on USB hub exceeds the 5V in AE it could trigger.

  The symptom is that the player is no longer lies in the Finder, or the base station appears in AirPort Utility.

  Endangered of AU base station is not uncommon.

  It responds to the pings? I guess he still has lights but is he blocked? You still get internet through it?

  Try to open it manually in to THE... use of the file / configure from others and put the IP address of EI.

  Talk with me by e-mail... It is open in the profile.

• Impossible to install the Raid drivers from the USB on the Tecra S series

  I tried to install the Toshiba RAID drivers (you know things F6) using a USB and emulating the BIOS USB FDD, well that detected the installation got XP file sytem was unknown.

  Any help?

  Hello

  If you use Windows XP RAID driver cannot be installed on the USB. It is not possible.
  You can install the RAID driver using only the drive FDD USB and floppy.

  But Windows Vista recognizes the USB and the RAID driver might be installed in this environment.

  So what OS and device do you use?

• OfficeJet Pro 8500 a: 8500 a plug the USB to the PC and wireless for Mac

  Our Officejet Pro 8500 a is connected via USB to our HP Pavilion running Windows 7. This connection works well. However, I tried to connect my iMac (OS 10.10.2) to the wireless printer with no success. If I disconnect the USB from the PC, I can connect wirelessly from my Mac. My question is: the Officejet Pro 8500 a does support multiple types of connections - one by USB and the other by wireless? If so, then I would appreciate help to understand why my Mac is not the 8500.

  Other details: our wireless router is Apple Airport Extreme. The wireless connection on the printer seems to work (I can print the details of this connection). However, when I try to add the 8500 to the Mac by using add printer, the printer does not appear. (The printer is lit and shows five bars of signal strength, SSID is correct and a valid IP address).

  My Mac is connected to the wireless network.

  Any suggestions?

  I was able to solve the problem of the printer with ethernet connection to the router that provides network wireless for PC and Mac. Now two machines are able to access the printer with no problems. By connecting with an ethernet cable, connect the printer wireless has been disabled. It had to be done because the wireless radio had become unreliable. The idea was that the blue wireless light never came. Thus by connecting wired LAN, all problems are gone. Thanks to the team of Geed for help.

• Cannot use the USB in the Portege M500

  Hello

  I use the model of laptop Portege M500. When I connect my Transcend 4 GB pen drive it detects and dispays an alrert lower-right with "new hardware found". At the same time another box dialog box opens asking for the installation, I tried to give next & finish but it does not.

  1A tried to install the drivers of the utility in the toshiba site.
  2. check the USB - it works very well in the other system.
  3. I use Windows XP. I checked the registry key to activate the pen drive.

  Ended in vain.

  It would be nice that you can share your ideas to connect the USB into the laptop.

  Thank you.

  Hello

  I had the same question that I couldn t use my pen USB drive more. After a search here a bit I started to remove the USB ports in Device Manager. Then I restarted my laptop and the USB ports are being installed again. Now, I have my USB again! :)

  In addition, it would be interesting to know if you have tested another USB key. Another one works

• How to install this update and resolve problems of USB and the touchpad?

  I Equium M50 (59th) and am bitten by an update that pulled my touchpad and keyboard. I did the new installation of XP Home and have all updated drivers and everything goes well. The last update, what I can't understand is for
  Ana _2005_10_24_V1.2 driver is for, Standard Open HCD USB Host Controller... X 2 .........

  The update addresses all kinds of questions like I'm having and is an update recommended driver detective, I use offten.

  The problem is that it says uninstall the drivers for the i have installed already and when I do it it hits off my USB mouse me leaving no able to install the new. When I reboot it installs those I don't want not reinstalled.

  This is the read me, off the coast of the new update and really I don't understand to underdstand what to do... .so here it is?
  Driver revision history:
  Twinhan VP704A Driver Release Notes
  -------------------------------------------------------------------------------
  Note:
  1. in the event that the system hangs when running with VP704A, please install ULI
  Host USB 2.0 in \ULiUSB20Driver driver

  2. for XP/SP1, please update with the patch in
  

  3. in XP/SP1, update driver will crash the system, while the new facility is ok.
  The trick to update driver XP/SP1 is illustrated in the following steps,
  a. uninstall the driver
  b. disconnect and reconnect the USB device
  c. install the driver
  4 to support the controller remotely, please launch Agent.exe in \Agent.
  Further details at \Agent\Readme.txt

  Known issues:
  1 multi-instance is not supported
  2 remote wakeup is not supported
  3. strong use of the processor from analog video/audio capture
  4. bad Signal using color YUY2 format IST
  5 AV sync if audio captured the wrong filter.
  (Difficulty: use the filter "USB Audio Device" in the flow WDM capture device)
  6. noise with analog TV and FM Radio
  (Difficulty: use the filter "USB Audio Device" in the flow WDM capture device)

  Driver revision history:
  -------------------------------------------------------------------------------
  2005-10-24, version: 1.0.2.8
  Bugs fixed and new features:
  1 is not correctly configured.
  -------------------------------------------------------------------------------
  2005-10-21, version: 1.0.2.7
  Bugs fixed and new features:
  1. the firmware version read FLASH OK!
  -------------------------------------------------------------------------------
  2005-10-14, version: 1.0.2.6
  Bugs fixed and new features:
  1.MUtil - access driver empty part lower part of screen when IST!
  2.MUtil - access HCT pilot check fix crash!
  -------------------------------------------------------------------------------
  2005-10-07, version: 1.0.2.5
  Bugs fixed and new features:
  1 tuner turns off when S-Video, Composite.
  -------------------------------------------------------------------------------
  30/09/2005, version: 1.0.2.4
  Bugs fixed and new features:
  1.agent.exe update for repeat bug!
  2.TI5150 sign up to fix video Format!
  -------------------------------------------------------------------------------
  2005-09-29, version: 1.0.2.3
  Bugs fixed and new features:
  1.A pilot of the trial build for multiple access medium. (in the folder "\Multi-Access")
  Note: The filter 'Audio device USB' provided by the system does not support mutil-access.
  2 reset TI5150 when a new frequency is defined
  -------------------------------------------------------------------------------
  2005-09-27, version: 1.0.2.2
  Bugs fixed and new features:
  1. difficulty I2C unstable access on some devices.
  -------------------------------------------------------------------------------
  2005-09-23, version: 1.0.2.1
  Bugs fixed and new features:
  1. analog TV becomes sometimes darker.
  -------------------------------------------------------------------------------
  15/09/2005, version: 1.0.2.0
  Bugs fixed and new features:
  1. difficulty of installation INF for Windows 2000.
  2 FM scan radio policy changed!
  -------------------------------------------------------------------------------
  13/09/2005, version: 1.0.1.9
  Bugs fixed and new features:
  1 USB string serial number not visible with USBView, updated firmware required.
  2. political analysis of FM radio, return of release if PLLOffset > = 9 x 12. 5 kHz
  -------------------------------------------------------------------------------
  13/09/2005, version: 1.0.1.8
  Bugs fixed and new features:
  1. after the passage between AV/D/A several times, video display becomes dark in THDTV 2.61
  -------------------------------------------------------------------------------
  12/09/2005, version: 1.0.1.7
  Bugs fixed and new features:
  1. improve the performance of check channel lock status
  2 pinnacle INF Fix.
  -------------------------------------------------------------------------------
  2005-09-09, version: 1.0.1.6
  Bugs fixed and new features:
  1. Add an audio initialization function.
  -------------------------------------------------------------------------------
  2005-08-31, version: 1.0.1.5
  Bugs fixed and new features:
  1 separation of PAL and NTSC resolution mode.
  -------------------------------------------------------------------------------
  2005-08-30, version: 1.0.1.4
  Bugs fixed and new features:
  1.AvgTimePerFrame.
  2 frame drop.
  3 pinnacle inf file HCT chkinf fail.
  -------------------------------------------------------------------------------
  2005-08-22, version: version 1.0.1.3
  Bugs fixed and new features:
  1. add remote control interface in digital source filter.
  2.A new remote test tool that contains of the source code in \Test_RC.
  -------------------------------------------------------------------------------
  2005-08-16, version: 1.0.1.2
  Bugs fixed and new features:
  1. Pinnacel & Twinhan driver & file reorg.
  2.VP704A_BDA_Test tool, add a test to the system code.
  3. set the standard infrared protocol of "IRSTANDARD", "IRSYSCODECHECK1" registry keys in the INF file.
  4 firmware update
  -------------------------------------------------------------------------------
  2005-08-15, version: 1.0.1.1
  Bugs fixed and new features:
  1 serial number feature is lost when the audio volume of the TV control
  2.RC6A support CIR
  (This firmware uses GPIO3 (M9207 pin 80) to decode the RC6 Protocol.
  The material must be reworked to connect the M9207 80 pin to the CIR module and the actual
  EEPROM must be flashed with \Firmware\M9207.bin)
  3 Serieal, MAC address and name of device OEM taken in charge.
  Please see for more details on the \Firmware\readme.txt.
  4 Ioclt example source code included.
  -------------------------------------------------------------------------------
  08/08/2005, version: 1.0.0.10
  Bugs fixed and new features:
  1. increase audio volume analog TV.
  -------------------------------------------------------------------------------
  04/08/2005, version: 1.0.0.9
  Bugs fixed and new features:
  1. analog TV Video mode failed.
  -------------------------------------------------------------------------------
  2005-08-03, version: 1.0.0.8
  Bugs fixed and new features:
  1.off - centerf frequency scan + / 125Khz
  2 difficulty program a copy scanned in MCE.
  -------------------------------------------------------------------------------
  02/08/2005, version: 1.0.0.7
  Bugs fixed and new features:
  1.THBDAConsole.exe 'ulFixedBW', 'ulDisableOffFreqScan', 'ulMCEFreqTranslate' bug
  -------------------------------------------------------------------------------
  2005-07-28, version: 1.0.0.6
  Bugs fixed and new features:
  1.THBDAConsole.exe 'ulFixedBW', 'ulDisableOffFreqScan', 'ulMCEFreqTranslate' support
  2. improve the stability of I2C communication.
  3 unify signaling resistance & quality as a THBda ioctl interface.
  4 capture filter lock state control.
  -------------------------------------------------------------------------------
  2005-07-28, version: 1.0.0.5
  Bugs fixed and new features:
  1. the same strength & quality signals as VP7046.
  2 debug build pilot
  -------------------------------------------------------------------------------
  2005-07-21, version: 1.0.0.4
  Bugs fixed and new features:
  1. put the INF update.
  -------------------------------------------------------------------------------
  2005-07-20, version: 1.0.0.3
  Bugs fixed and new features:
  1 improve performance in PCM4
  2 passage of the analog TV Mode to FM Mode failure
  -------------------------------------------------------------------------------
  2005-07-04, version: 1.0.0.2
  Bugs fixed and new features:
  1. production tool FM test OK!
  --------------------------------------------

  And here is the Readme file from the other file in the update?

  ************************************************** ************************************************
  ULi PCI to USB Enhanced Host Controller Driver V1.72 for Windows 98 SE, Windows ME, Windows 2000 and Windows XP
  ************************************************** ************************************************

  ----------------
  INTRODUCTION
  ----------------

  This driver supports the host EHCI ULi controller under Windows 98 SE, Windows ME, Windows 2000
  and Windows XP.

  -------------------------
  CONTENTS OF THIS DOCUMENT
  -------------------------

  1. installation instructions
  2. uninstall instructions

  ----------------------------
  1. installation instructions
  ----------------------------

  (Windows 98SE & Windows ME)
  ULi USB 2.0 Controller has strapped on the system
  1. install the driver USB 2.0 ULi
  -Run the Setup program.
  -This program will copy the driver files in your Windows system, and then restart your computer.
  2. after the system restarts, Windows will detect the new hardware 'ULi PCI to USB Enhanced
  Host Controller"and install the driver.

  B.If any ULi USB 2.0 on the system controller
  1. install the driver USB 2.0 ULi
  -Run the Setup program.
  -This program will copy the driver files to your Windows system, then turn off your computer.
  -Fix the ULi USB 2.0 computer controller card and restart your computer.
  2. after the system restarts, Windows will detect the new hardware 'ULi PCI to USB Enhanced
  Host Controller"and install the driver.

  (Windows 2000)
  ULi USB 2.0 Controller has strapped on the system
  1. install the driver USB 2.0 ULi
  -Run the Setup program.
  -This program will install and load the driver and you do not have to restart the
  computer.
  B.If any ULi USB 2.0 on the system controller
  1. install the driver USB 2.0 ULi
  -Run the Setup program.
  -This program will copy the driver in your Windows system files, before turning itself off
  your computer.
  -Fix the ULi USB 2.0 computer controller card and restart your computer.
  2. after the system restarts, Windows will detect the new hardware 'ULi PCI to USB Enhanced
  Host Controller"and install the driver.

  (Windows XP)
  ULi USB 2.0 Controller has strapped on the system
  1. install the driver USB 2.0 ULi
  -Run the Setup program.
  -Click "NEXT".
  -This program will install and load the driver and you do not have to restart the
  computer.
  -Once install the driver ULi USB 2.0 successfully. System will detect "USB 2.0 Root '.
  Hub. " Please select "Install the software automatically (recommended)" and then
  Click 'Next' to continue the installation.
  -This program will install and load the driver and you do not have to restart the
  computer.
  B.If any ULi USB 2.0 on the system controller
  1. install the driver USB 2.0 ULi
  -Run the Setup program.
  -This program will copy the driver in your Windows system files, before turning itself off
  your computer.
  -Fix the ULi USB 2.0 computer controller card and restart your computer.
  2. after the system restarts, Windows will detect the new hardware 'ULi PCI to USB Enhanced
  Host Controller', proceed with the installation.
  -Once install the driver ULi USB 2.0 successfully. System will detect "USB 2.0 Root '.
  Hub. " Please select "Install the software automatically (recommended)" and then
  Click 'Next' to continue the installation.

  Notice:
  If you can not configure driver successfully. Please restart your system, then follow
  steps to reinstall driver above.

  ------------------------------
  2. uninstall instructions
  ------------------------------

  1. open the "Control Panel" folder.
  2 call the "Add/Remove Programs" icon
  3 choose the "ULi USB2.0 Driver" section.
  4. click on the "add/delete" button to remove drivers.

  -----------------------------------
  Change list:
  -----------------------------------
  1.74
  1 fix this multi-interface keyboard may not be detected on the USB 2.0 hub.
  2. support all USB2.0 Host Controller.
  1.73
  1 problem on Win98SE, blue screen when you unplug a USB 2.0 Scanner after scanning image.
  2 solve problem on Win98SE, blue screen when you unplug a few Scanner USB 2.0 USB 2.0 Hub after scanning image.
  3 fix on Win98SE, blue screen when copying of files through the hub of UH-204 SUNBOX.
  4 solve problem as wirless lan will disconect when the plug in usb device.

  1.72
  1 fix that system crash when HD USB copy large files.

  1.71
  1. improve the management of power in Win98 / Me.

  1.70
  1. improve the devcie detection function.

  1.62
  1 solve the problem that can not operate a USB HUB USB 2.0 disk when the system resume inactive.

  1.61
  1 solve the problem that some device under USB 2.0 HUB is not found if resumes suspension system.

  1.60
  1. in support of functions power management when a HUB with the USB plug in device
  a root HUB.

  1.57
  1. Fix USB with USB 2.0 HUB floppy cannot detect problem.
  2. fix audio problem that can not display smooth when peripheral USB connect to the system.
  3. fix system cannot detect DVICE USB when the USB device attached to the system in
  suspend mode.
  4 fix when root USB HUB have a full load, USB HD sometimes
  failure of the transaction.

  1.56
  1 fix that device of DVD decoder cannot display correctly.

  1.55
  1. fix OTI USB 2.0 drive hand cannot detect question.
  2. attach the USB mouse cannot be used after the resumption of hanging.

  1.54
  1. to improve the safety of the driver.

  1.53
  1. transfer bulk fix may stop if the USB device is connected to the USB 2.0 hub
  2 difficulty USB 2.0 mass storage device cannot access after the release of the standby mode if there is an another USB 1.1 existing device

  1.52
  1 correct fault of system pages when accessing the storage of mass Win98SE or scandisk device failure when selecting
  automatically fix file system errors
  2. fix system may hang on in Win98SE / ME if USB 2.0 cardbus card is plugged

  v.1.51
  1. to improve the compatibility of USB 2.0 card reader.
  2. fix USB IDE devices are not accessible after the release of the standby/hibernation mode.

  v1.50
  1. improve the transfer block

  v1.48
  1. difficulty of installation of the USB 2.0 LAN driver hangs up
  2. attach a USB 1.1 card reader cannot be identified when plugged into the USB 2.0 hub
  3. fix some laptops starting hanging Win98SE

  v1.47
  1. improve the performance of bulk transfer.
  2. fix the failure of USB 2.0 Preview in bulk webcam.

  v1.46
  1. support USB 2.0 and 1.1 devices isochronous
  2. fix system hang up when restarting system if the USB 2.0 host controller is disabled in Win9X / ME
  3. fix system hang up when you uninstall the driver if there is USB 2.0 connected under Win2K/XP devices
  4. improve the capacity of the device detection in Win9X / ME

  v1.45
  1. fix system hang up when the mode standby ACPI.
  2. attach the mouse sometimes does not disappear when it is unplugged.
  3. fix the failure of detection of composite devices Win9X and improve device composite Win2K/XP

  v1.44
  1. composite crutch
  2 improve the detection of devices

  v1.43
  1 improve the failure rate of transfer IDE read/write with USB 2.0 to IDE bridge on the platform of PC card
  2 difficulty at high peripheral speed detected as full-speed device
  3. fix some problem of failure detection USB mouses
  4. fix some problem USB 2.0 Hub failure detection
  5 difficulty Win98SE crashing if ULi EHCI 1.42 is installed

  v1.42
  1. fix PC Card eject hang up in Win98 / ME
  2 difficulty of interruption/resumption hang up in Win98
  3 sometimes solve USB 1.1 device cannot be detected if OS starts with USB 2.0 and 1.1 devices plugged
  4. fix some failure detection of PC Card USB 1.1 devices

  v1.41
  1. Add new feature that system can install the driver ahead of the device is plugged in.
  2. fix PCMCIA OHCI controller resources affect problem on Windos ME.

  v1.40
  1. support Win9X/ME / 2 K/XP with ULi USB 2.0 driver.
  2 fix PCMCIA EHCI controller detection device USB 2.0 problem in Win9X / me.

  v1.32
  1. Fix problem that pilot cannot detect the Microsoft driver in Windows XP
  If the path of the OS is not c:\windows.
  2. Fix problem that pilot cannot detect the USB 2.0 controller device in a system.

  v1.31
  1. Fix problem that driver cannot install on Windows 2000.

  v1.30
  1 fix than Win9X / shows ME no USB 2.0 hub.
  2 solve the problem that hang up when the second entry in Win9X S1 with HID device connected.
  3 Fix problem that sometimes when you click on "search the hardware changes.
  for PNP ULi USB2.0, controller, the system will inform you the usbehci.sys
  file is not found.
  4. Fix problem that v1.20 can't find no EHCI controller to install the driver for after different
  verison of ULi EHCI controllers devices are connected and disconnected.
  5 install the driver support for several features of controller EHCI ULi existing on
  system at the same time.
  6. determine Win2K/XP shows hub USB root for USB 2.0 hub.

  v1.20
  1. support ULi USB 2.0 for Windows 98SE/ME/2000/XP host controller driver.

  ULi Coporation. (ULi) web sites:
  http://www.Uli.com.tw/ (Taiwan)

  CAN SOMEONE TREAT ME LIKE A CHILD OF TWO YEARS AND GIVE SOME ADVICE AS TO HOW TO OBTAIN THIS UPDATE.

  I'D VERY GRATEFULL AND KIND OF THINK IT would BE BENEFICIAL to a LOT MORE than PEOPLE LIKE I SEE a LOT OF XP AND PROBLEMS OF THE KIND THIS UPDATE IS SUPPOSE to FIX.

  It is said above 2 relevant and 1 right ANSWER available...

  I'm new here, so anyone could direct me to these answers?

• HP Mini 200-4200 doesn´t give USB in the Start Menu

  Hello!

  I have: HP Mini 200-4200, pr B3R47EA #ABU nr. Hard drive died, received a new one and I've been waitng for the upcoming USB info. I just got my USB with the news of recovery on it in time. (Recovery USB key is - 685741-034)

  I followed the instructions, but in the Start Menu of Options, he didn t give me an external drive. He gave me 3 options - hard drive for HP laptop, network adapter.

  I didn t know what to do, and the thought I´d go out of the system and ask for advice here. Press Esc. He then continued in the Recovery Manager. So I thought, Whew!, it'll work. Now however, he got stuck for about 3 hours (he can´t think as long?) in the present:

  "Recovery image factory preparations."

  Did you receive any additional disk supplied with the system recovery media? If so, insert it now; otherwise, click on ignore.

  Please wait. »

  The USB stick has been inserted all this time. Now, after 3 h in the same screen, I got him out for a second and put it back, no change.

  Current today?

  (should I press the 'skip' button?)

  SOS!

  ::::::::::::::::::::::::::

  While waiting for a response, I stopped the mini and returned to the BIOS (no idea what I m done - but in some post, someone said they changed their boot order... went to look for that)

  In the Conf system boot order appears like this: hard drive for laptop, USB floppy on say hard Key/Usb, CD-ROM Usb CD/dvd drive! USB floppy (with an exclamation point!) and network card. In the Boot Options startup disk has been disabled... I activated it. just in case... no idea what it means. After this USB doesn´t floppy have a "!" in this topic.

  Should I change here something to conditioned USB option? The order?

  I turned on my mini 3 times with the USB key in one of the 3 locations every time... it s do not know a good idea, but it's just doesn´t give me the option of Start Menu...?

  Now with everything enabled in the boot order... doesn´t still come as an option.

  :::::::::::::::

  People also speak of traditional can´t find anywhere in the BIOS to change any setting?

  ::::::::::::::::

  Oh and when I pop the USB in a location to another computer, it starts to read... but I m too ignorant and afraid to see that then happens, so I just took new.

  Start by using the option for "floppy USB disk hard key/Usb. This should return you to the same place as before. If it is not, disable booting to USB floppy option and try again. Since you did not receive an "additional disk" with your USB recovery media (and even if you did, you could not use it unless you have a USB CD/DVD drive), you'll want to press 'SKIP' when prompted. Then, just follow the prompts as required and eventualy Windows will be installed.

  Good luck and after back if you encounter other problems.

  Please send Bravo

• RN204 not reconnect the USB in the port back after reboot.

  I don't know if that's a problem, but my new RN204 unit will not see my USB stick after reboot. Key, I inserted into the lower back USBport. Port superior return I got UPS. Inverter is connected ok after reboot.

  If the USB is in front of USB port, unit connects OK after reboot. Rear ports, I have to go out and re - insert USB stick after every reboot. Key is detected and mounted after rehabilitation only. (connected external storage device.)

  USB drive is Kingston USB 3.0 and my RN104 unit detects that it restarts after all in backport more or less right. (after a reboot it tell me automatically (connected external storage device.))

  FW on the two unit (RN204, RN104) is 6.4.1 - T35, tested on 6.4.0 and 6.4.1 beta 1-2 - all the same.

  Hi all

  After you install the new version of FW 6.4.2 (Final, published today), everything looks OK. My RN204 unit reconnect all the USB key, that I tested.

  Everything is OK, the Bug disappeared. I think that FW 6.4.2 is the solution to the issue being reported.

  Thanks Netgear.

• Universal Serial Bus (usb) controller - the missing driver problem

  1. Hi all.
  • Name of the product and operating system: HP (Notebook) 15-r003sv - Windows 7 x 64
  • Product no.: G7E53EA #AB7

  This laptop has windows 8 and everything works fine, then I installed windows 7 x 64 and I have problem with the usb ports. they do not work and are of unknown devices

  I tried everything posted on the internet, but nothing.

  How can I find a driver for USB controller for my device?

  Thank you to

  * Also, I installed 3 drivers in my page of devices support for hp drivers (sp66602 etc, under the chipset). It extracts to a folder, I found and run but said the error message "this computer does not meet the minimum requirements for installing this software.

  Hi all!
  
  The problem is resolved.
  Thank you all to try it.

  Now, the magic software that solved my problem was "pilot identifier. (I didn't know it)

  It can detect unknown hardware ID devices (as you did) and recommends drivers for them.

  The pilot who was the solution has been Intel USB 3.0 eXtensible host controller driver.
  They are different but you choose the one that is compatible with your chipset.

  Pilot identifier recommend correct.

  Installation: Just run a single setup.exe, and that's all!

  Thank again!