pouvez S10-3 turns AERO GLASS under Win7 ULTIMATE?

Similar Questions

• Tecra S10 - 64 bit of Vista and Win7 64 bit driver question

  Hello

  I own a Tecra S10 and using Vista 64-bit operating system.
  Unfortunately Toshiba isn't supporting this version of the OS, because pilots proposed must be taken on different products that use the same hardware.

  Is anyone know wether Toshiba will start sharing the drivers for Vista 64 bit soon and whats on Win7?

  I think that Vista 64-bit drivers will run under Win7, but * when they officially released drivers for 64 bit Vista or Win7?

  Any info would be interesting.

  Thanks in advance.

  Hello!

  Normally it comes out drivers * after the release of the operating system. This means you have to wait a few months more I think
  But you think contacting Toshiba? Guys, you should know better than us users here. If you write an email or call, it takes only a few minutes!

  In addition, you should try the Vista 64 bit drivers. Most of them also works under Windows 7.
  And it s worth a try! ;)

  Good bye

• LV2010 32-bit under Win7 64 bit - SCC provider not found

  Is there a work around to use a provider of Source control with LV2010 32-bit under Win7 64-bit?

  It seems that the VI 'Raspberry find all Providers.vi' does not work with the OS 64-bit due to registry access restrictions.

  The Key.vi of open registry is not able to analyse below HKey SOFTWARE but the full path is SOFTWARE\SourceCodeControlProvider\InstalledSCCProviders.

  Best regards

  Christian

  By reading this thread http://forums.ni.com/t5/LabVIEW/LabVIEW-32-bit-and-Vista-64-Registry-Read/m-p/978676#M438513 , I was able to get a work around.

  I replaced the version registry key VI opened by the ".vi ACI - WinAPI - open registry key (WOW64 support)" within raspberry NI find all the Providers.vi and now I can choose the SCC provider installed via the LabVIEW IDE-tools >-> Source code control-> configure source control.

• My computer will not be stopped by using the "turn off computer' under 'Start' (lower left corner)

  My computer will not be stopped by using the "turn off computer' under 'Start' (lower left corner)

  Hi Harry,.

  · What happens when you try to stop?

  · You receive an error message or error code?

  · Do you remember all the recent changes on the computer before the show?

  · What is the service pack installed?

  You can check the link below: Windows XP Shut Down and auto-restart issues: http://www.microsoft.com/windowsxp/using/helpandsupport/learnmore/russel_02may13.mspx

  Advanced Troubleshooting for shutdown problems in Windows XP: http://support.microsoft.com/kb/308029

• How to rename tasks scheduled under win7?

  I would like to know how to rename tasks scheduled under win7

  Does anyone have any suggestions?

  Thanks in advance for your suggestions

  It can't be renamed directly, but if you export the task at any place, then re-import, it can be renamed during the import process.

  Then just delete the old task.

• Windows 7 Aero / Glass no effect no more working time

  My computer is Windows XP on your main HARD drive. I added another HARD drive and installed Windows 7 Ultimate (32 bit), the feature in question worked but I had problems with fuzzy texts and also I can not set the resolution recommended for my monitor.

  I downloaded and installed the drivers for my monitor from the manufacturer's website but since it does not solve the blurred fonts, I tried to find the latest drivers for my card through the Device Manager. I noticed that the version of the driver was older (Date of the driver in the course of 2009) that is used by the computer when I boot it Windows XP (driver of 2010). Even if I tried to update, it says that he already has the latest driver for it. I managed to save the display drivers XP uses and updated Windows 7 with her ("disk," method etc.) and I finally got the resolution which is best for my monitor that makes fonts very sharp and any other clear enough. I then installed the ATI Catalyst Control Center (was struggling so he can install properly - missing. INF file, CCC not launch, etc.) but I managed to make it work in the end.

  Unfortunately, I lost Aero / glass effect. Troubleshooting (made sure advanced option 'Applies automatically repairs' is checked) gives me the "current video card can support Aero with a driver that is compatible with the Windows Display Driver Model (WDDM).  Contact the manufacturer of your video card or computer for a WDDM compatible driver. "message and finally the error 'Video card driver doesn't support Aero effects. "I thought it's because the drivers of Windows XP was not intended for Windows 7 I so uninstalled and returned to the former working driver, uninstalled ATI Catalyst Control Center (cleaned all the remains) and reinstalled it but ATI does not find the. INF file so it can't update the drivers. Then, I just reinstalled Windows XP drivers.

  Here are some details:

  (After updating the graphics card with the XP ones)

  Adapter type: ATI Radeon X 300/X 550/X 1050 Series

  Driver date: 10/02/2010

  Driver version: 8.593.100.0

  Before I updated with drivers that Windows XP uses now, I remember when Aero was still working (but the resolution is bad), the Date of the driver was some time in 2009.  I read about the update of Windows KB2670838 and discovered that I had installed so I uninstalled it but Windows 7 cannot always bring Aero without it. I don't understand why Aero works with a previous version of a driver but not later.

  Has anyone met and discovered how fix this problem without having to reinstall the operating system? Or should I really give up Aero and settle for the appropriate monitor resolution?

  Thank you!

  Uninstall the current driver.

  Then download from the ATI site: http://support.amd.com/en-us/download on your hard drive.

  Then install.

  (Latest version of the driver is 10.2)

  J W Stuart: http://www.pagestart.com

• Activate aero glass on Windows 8?

  Original title: Aero Glass

  enable aero glass in windows 8?

  To add to this, I think that there should be an option to restore, with the default opacity does nothing to affect the performance of the system.  Solid slabs of color can be a little awkward and the effects Aero 7 made chrome much less intrusive user interface.  Darkening of the color palette doesn't help, because it makes some much stronger colors and the text of the user interface is made more difficult to read.  Desaturate the colours too would also make more difficult to differentiate between active and inactive windows.

  As the taskbar is transparent, it would be certainly possible to do the same thing for the title bars and also include adjustable opacity levels.

• 2.04 Ubuntu comments on VMware Workstation 9 under Win7 can't see ext4 USB drive

  Comments from 2.04 Ubuntu on VMware Workstation 9 under Win7: on computer A trivially, I connected to an out-of-the-box 64 GB USB drive formatted for VFAT on Ubuntu in a VM. I re-init'ed the player for ext4 (mkfs.ext4), mounted, drop a bunch of stuff on him (which took awhile), he dismounted and walked away. The next day, identically configured computer B, I inserted the USB key. Natch, Win7 may not go up because it does not ext4. But Ubuntu don't see either, so I can't be installed. Do not see under removable devices, no small icon bottom left of the screen of VMware, nothing in the settings menus or properties, etc. I think it's just me being a noob to VMware, but it seems that Ubuntu under VMware Workstation 9 cannot see the drive unless Win7 can go up. Seems unlikely. KB searching, Googling, etc. produce many unrelated things. Ideas? AdvTHANKSance.

  Here is the final answer: works great on an earlier version of VMware Workstation 9 on one of the Windows 7 of my client machines, it didn't work on my Windows 7 computer. I upgraded to VMware Workstation 10 on my Windows 7 computer, and now it works perfectly. If I call you this a bug in this version later 9 which was set at 10. Could also be had I simply uninstalled 9 and reinstalled which would have fixed it too. But I'll never know.

• Resize the volume & Aero Glass on Vista

  I recently bought a MacBook and installed Windows Vista Ultimate on it using VMware Fusion 2. For some reason, he chose to give Windows a volume of 40 GB, which I felt was too small, but I couldn't change it. I used the settings of the Virtual Machine and has increased the size of the volume to 60 GB, and she seemed to accept but did nothing major that I clicked OK. When I have botted Windows, he always says the volume was 40 GB. How can I increase the size of the volume to 60 GB? If I've touched 40 GB, it will add a new 2 GB to the volume I have the possibility to use 2 GB files (rather than 1 large file) selected?

  Also, can I the Aero Glass interface work?

  Once you extend the vmdk file to size, you can go to disk management, and you can extend the disk to the new size.  Regarding the Aero, vista looks like the video card and usually decides whether she can handle the stress of the experience.  I know they have upped the virtual video card to manage several games and others, but I don't know if it is powerful enough to run aero.

  • Kyle

• Confirmation of chipset? under Win7 (m7367c) Emery

  I upgraded my HP Media Center m7367c (Emery) of XP > Win7 Ultimate 7600 Build. Does anybody know which chipset Windows 7 installs during the installation? Where in the Device Manager are they appear? I want to upgrade if they need. Not sure if I'm looking in the right place.

  Data sheet: HP Media Center m7367c

  Windows 7 Ultimate Build 7600 (XP Media Center Edition 2005 SP Upgaded 3)

  BIOS Asus P5LP-(Emery) 3.19

  4 GB of RAM DDR2-PC2-5300 667 mhz

  Gigabyte Radeon HD 4670 512 DDR3 (CCC - 10.5)

  Sound Blaster x - fi Xtreme Gamer (pilots are underway)

  HP - 840b DVD/CD-RW DL

  CD-ROM/DVD-ROM

  I thought about it. FYI: Windows 7 RTM 32-bit Build 7600 installs the Intel Chipset version 9.1.1.1016 driver regarding the motherboard Asus P5LP-(Emery).

• Cannot install Adobe CS5.5 Master Collection under Win7 x 64

  Hellom

  I bought a lot of adobe products in the past, and I was generally happy with them.

  However, I downloaded a demo of the CS5.5 Master Collection, and it will not be installed.

  I followed all solutions in http://forums.adobe.com/thread/628980?start=100 & tstart = 0 , but nothing helps.

  I received a diagnosis of the root of the problem, and it's C:\Users\Yunyu\Desktop\MasterCollection_CS5_5_LS1\Adobe CS5_5\payloads\Microsoft_VC90_MFCLOC_x86\Microsoft_VC90_MFCLOC_x86.msi will not be installed.

  I've got when I try to install, and the Tower of registry key does not work for me, as there is no registry key.

  Win7 Ultimate x 64

  No antivirus

  What should I do?  I contacted adobe, but they are unresponsive.

  I really want to try and buy this product.

  Hey guys,.

  I did what lordalpha1 said and it worked like a charm! Thanks a lot, man! I searched for a solution days already. I read the post and you have pretty much done everything I had tried less replacement of files. Furthermore, pipjunkies, I replaced the two files in the folder of the payloads with the 64-bit version, and it installs quickly without error. It sounded like you can have just replaced a. Try to do this for both and give that a try!

• Satellite A300 (PSAG8E) - hardware problems after I installed win7 ultimate

  Hello and good day,

  I installed win7 ultimate a few days ago, windows was able to recognize most of my material accepts my build of microphone and camera and another component, I'm not sure what it is (Windows Update automatically downloaded the driver of sound and graphics for me).

  My questions are - where you can find the remaining drivers and where can I get the preinstalled Toshiba tools and software? (The site pilot in the support page Toshiba does not include drivers and software)

  Thank you very much
  King Ben Simon

  Hello

  I have the Satellite A300 (PSAG8E) too and installed Win7 Home premium and everything works perfectly.

  Initially, I must say that I do not know where you are looking for the drivers and tools of Toshiba and that all things because utilities are downloadable on support Toshiba & download page under http://eu.computers.toshiba-europe.com

  It is logical that MIC will not work if you have not installed the appropriate driver. Installing drivers only and not using Microsoft update. What you need are the real and tested and not some free drivers of the internet.

  Go to the Toshiba download page and install all the stuff following this order of installations:
  -Win7
  -chipset driver
  -Storage Manager
  -display driver
  -driver sound
  -modem driver
  -utility supervisor
  -infrared
  -patches
  -configfree
  -VAP
  Hardware - toshiba
  Control - HDMI
  -WLAN driver

  Everything works well but lacks some drivers

  Added Vista tips:
  Toshiba - help - working properly
  -Card reader - installed correctly
  -Webcam driver for A500 - tested with Skype - works correctly.
  Driver - Synaptics

• Lost aero on windows vista ultimate / I now the victory of base

  I lost Aero under vista ultimate, now he went to basic windows how to

  it back, it is said a recent pilot program is causing a problem, I recently tried to install edge mirror set, then happened, help please.

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-desktop-theme

  Read the above about the themes of Vista.

  If you still have problems of re-download drivers graphics:

  Go to the website of the manufacturer of your computer/laptop > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  See you soon.

  Mick Murphy - Microsoft partner

• the sreen join dim after upgrade from win7 win7 ultimate

  Why the screen on my sony vaio turns dim inlight after that I have upgraded to win7 home premium to win7 ultimate.can you help me how to do the sreen for your help brighter.thank.

  Thanks for your help, I'll try.

• Having previously worked now Readyboost does not activate flash on Win7 ultimate x 64

  Hi people,

  I use a SanDisk cruzer micro 8GB flash drive for awhile with win7 now and I alternate between use as readyboost and storage.

  But recently the readyboost option stopped on the AutoPlay list. Then, after a restart it came back, but every time I select the flash drive > properties, there is no readyboost tab to be seen.

  The only changes to the system are that I added a USB printer and scanner USB. What the hell is happening?

  I tried to format, reinstall SanDisk U3 launcher, I tried diskpart own all etc, etc. But nothing seems to give me the option
  to enable readyboost.

  Anyone got any ideas? The really strange thing is that readyboost was working fine last time I used the flash drive with Win7.

  Any help much appreciated.

  Hi Khaled,

  Nope, none of that helped.

  But I think that the reason for the problem of readyboost is that Win7 didn't like the fact that I had hacked an install of my Nikon Coolscan 5ED the USB and Canon LIDE35 USB devices to work under Win7 using old drivers 64-bit XP and Vista.

  I have now re-installed Win7 and I can confirm the two my SanDisk Cruzer Micro 8 GB and 16 GB USB key work correctly with readyboost again.

  On the plus side, I realized that I wasn't not take full advantage of my computer RAID storage. I have a controller matrix RAID Intel 10CHR and after having read up on the site intel I have now installed Win7 with a RAID0 to 3.4 volume and super fast and a volume RAID5 1 TB on a range of 5xHDD 5xHDD.

  anyway thanks for the help guys.

  MegaWatt78