Power problem - computer from HP Pavilion 23-h055la all-in-one desktop touch

Similar Questions

• External monitor to an hp pavilion 23-b010 all-in-one desktop?

  I just bought a hp pavilion 23-b010 all-in-one desktop computer... can I connect it to an external monitor? and if so, are there special requirements for the external monitor?

  Here are the specifications of your all-in-one HP Pavilion 23-b010 computer office. According to the specifications, this computer has no video output of any kind ports (DisplayPort, VGA, DVI, or HDMI). You will need to purchase and use a USB-to-video as the EVGA UV adapter more + UV39 or UV19 to connect an external monitor to your computer.

• 2nd video device HP Pavilion-23-a304a-All-in-One Desktop PC E9V70AA

  Hello world

  I'm new to the forum. I just bought a HP Pavilion all-in-one 23-a304a Office P E9V70AA.

  One thing that I forgot to check was I can plug in a laptop and use the HP as the DISPLAY monitor, sometimes I work from home and using the larger screen would be great, but I've noticed that there are no HDMI or other video ports on the desktop.

  The thoughts and thanks in advance.

  Rob

  Hello

  It has not designed this way, you can not use it as a stand-alone monitor for your laptop.

  Kind regards.

• The lid opening rear of the hp Pavilion 23 - f250 all-in-one desktop

  Hi TwoPointOh

  Thank you for let me know the step by step process the opening on the back of the NEW (2013) hp Pavilion 23-f250 Office all-in-one to add ram memory. There are a few online video, but not for 23-f250, is there one for a Jules Destrooper?

  Thank you

  Hello

  Try this Guide maintenance and upgrade HP.

  Removal of Modules of memory

  Before you start: Remove the VESA cover and back cover.

  Measures

  1. Carefully remove the shield EMI covering the memory - locations take care of is not to damage the battery on the motherboard.
  2. Then, pull gently on the fixing lever on each side of the SO-DIMM memory module.  The module will pop up in its socket.
  3. Remove the module from the plug.

  Replacement of Modules of memory

  Measures

  1. There is a small notch on one side of each SO-DIMM module that fits on a small tab on one side of each shot SO-DIMM.
  2. To replace a module of memory SO-DIMM, angle of the module at about 45 degrees, engaging the notch in its socket tab.
  3. Push the module in place until the levers of fixing snap into position above the sides of the module.
  4. Carefully align the top edge of the EMI Shield over the opening slot of memory on the shield of the motherboard - then press it down into place.

• scanning of pictures on my computer from the series of J611 all-in-one HP Deskjet 3050 has

  I've uninstalled and reinstalled the software, but when I try to scan, the message arrives that the scanner can not find my computer.  What should I do now?

  Hello

  It's much better scan from your computer, this method allows more options. But if you want to scan from the printer to your computer, you must initiate or enable the analysis of the computer first TO your computer (Windows):

  (a) click (or double-click) the printer icon.
  b click on Manage scan of the computer,
  (c) enable

  You can start this option with Windows by checking a square box.

  Kind regards.

• HP Pavilion 23-a200a all-in-One desktop PC

  critical error is not going past this error

  tried to let him do a repair via windows repair work not to go in front of her and is not reding any our external dvd player usb

  If I can get the data off hd

  can someone help please

  Hello @RIMTECHMOB,

  I understand that your computer displays a critical error, and that you are not able to run a repair of the operating system Windows. What is the full error message exactly as it appears on your screen? You are able to start your computer in Mode safe?

  In the meantime, I recommend that you follow the steps described in this document on using Microsoft System Restore (Windows 8) when your computer is not able to start normally. If you are not able to restore or restore your operating system, please follow this resource on HP System Recovery troubleshooting (Windows 8).

  Please re-post with the results of your troubleshooting, as well as the information requested above. I look forward to your reply!

  Concerning

• Power problems: computer turns off when the power supply cord is unplugged.

  original title: power problems: computer shit turned off when the power supply cord is unplugged.

  I have a HP Pavilion dv2000

  Windows vista home premium/sp2

  AMD Turion (TM) 64/2 1.80 ghz processor

  1 GB memory

  32 bit operating system

  I have 2 problems with this laptop.

  !. I have lost the power cable and bought an expensive one online step (model: PA-1650-02 c. input 100-240v 1.5 put out a(1,5A) 18.5V 3. 5 = a)

  When I first plugg cord battery charge light came on the balance, then he started to come on and outside.

  now its completely off, even with the power cord plugged in. on the lower right part of the screen its showing that cord is connected to the power supply and the battery is fully charged, but as soon as I unplugg the power cord or remove the computer cut right away.

  the second problem is that the left mouse botton does not work, the work aside right very well. I went in the proprties to put it right, click on to, but who does not work either. I've updated the drivers but still nothing.

  Any help will be greatly appreciated.

  Hi aloum,.

  (a) what kind of mouse you are using?

  (b) the left button of the mouse seems to be stuck or it does not meet the click? This only happens with certain applications?

  Step 1: Test the mouse on another computer or another mouse on the test computer

  To determine whether the mouse or the computer is defective, follow these steps:

  1. test the mouse in question on a system that works, you know. If the problem appears to follow the mouse, you may need to return or replace the mouse.

  2 test a mouse you know is working on the computer in question. If the problem seems to stay on the computer, then the problem is most likely related to the software.

  In regard to the battery not holding charge

  Battery problems are often associated with the battery itself. If you encounter this problem, contact your mobile PC manufacturer. If you purchased the battery separately from the notebook computer, contact the manufacturer of the battery.

  Troubleshooting battery problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-battery-problems

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• HP Pavilion - 27qe touch everything-i: HP Pavilion - 27qe touchscreen all-in-one PC Downgrade of Win10 of Win7 Pro 64 bit

  I ordered, from hp store-still in production, a HP Pavilion - 27qe touchscreen all-in-one.  There are 10 Windows.  I would come down to Win7 Pro 64-bit (I can buy a legal copy of win7 and do a clean install).  I understand that I would lose some features like the touch screen, but I really prefer Win7.  I'm looking for info on how to do this?  For example, where to find the proper drivers (determine which and where to download to), BIOS etc.  Drivers listed on hp for this computer are for Win10 only, there is no Win7 drivers listed.  Of course I'd first recovery disks Win10, where I always want to go to the Win10 or if Win7 is not working properly.

  Any info/help appreciated.  My wife and I share one our computer at home with Win7 on it.  Me, my wife and probably would be better to use Win7 we are used and as.

  Thank you...

  Thanks for the info WAWood.  I decided to nix the idea of decommissioning.  It would be too complicated, as you point out.  Have a good!

  I noticed that you have been very busy here.  Member for 2 months and almost 500 posts!  Thanks for you disseminate knowledge and activity here.

• Upgrade memory for HP Pavilion 23 - g040xt CTO all-in-One desktop

  When I ordered my

  HP Pavilion 23-g040xt CTO of all-in-One desktop PC I could only afford the version of 4 GB of Ram. Now, I want to upgrade the memory up to 16 GB. I have a few questions

  1. I noticed all this in a use SODIMM and I was wondering if I could buy any DDR3 SODIMM for this or if I have to buy a specific manufacturer?

  2. now, I have only 4 GB using 1 of the 2 memory slots. I'll be able to buy 2X8GB and use this location empty on my motherboard and run dual channel?

  3. How do the memory locations? Just pop the back of all in one PC?

  Thank you

  According to the specification, this model supports up to 16 GB (2 x 8 GB), as follows:

  Dual channel memory architecture
  Two DDR3 SODIMM Sockets (204 PIN)
  Supports the PC3-12800 (DDR3-1600)
  Supports 1 GB, 2 GB, 4 GB and 8 GB DDR3 SODIMM

  Any brand or model of RAM memory that meets the following specifications should work on your computer. If you have 4 GB in a housing, you will need to remove it to install both 8 GB DIMMs. Yes, you just need to pop on the back.

  There should be two or more screws on the back that need to be turned counterclockwise until you hear each "click" of 5-6 times. Then, take a lower corner and lift the corner. Repeat with the other bottom corner. Now, lift the... starting back down. You may also need to remove a cap on the memory locations to access.

  If you have any other questions, feel free to ask.

  Please click the White Star of KUDOS to show your appreciation

• Wireless network problem unable to connect to Kodak ESP7 All In One Printer wireless. Windows 7

  Hi close baldy headed by trying to connect a Kodak ESP7 printer all-in-one wireless. The printer itself recognizes the wireless connection which is excellent but the does'nt of the computer. Whenever I try and print something an error message printer does not. I tried resetting the wireless router, is returned at the beginning and installed the software again, but no luck. I am on Windows 7 and the other 2 laptops that I have in the end work from home. Could someone tell me if I'm missing something simple, or would it be a problem with the printer itself. Thank you
  Phil

  Hello

  Configure the primter with a static IP address to connect diretly to the router (read the printer manual).

  Then using the Kodak software, install the printer driver and utility management, on each computer that requires to for use.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Incredible problems to get the new workgroup C8180 All-in-one

  I bought a C8180 All-in-one printer to the end of September. When I plugged in and installed the software, everything seemed to function OK (I didn't test printing from the computer at the time), but after a short period of time to print Microsoft Word and Wordpad failed, started working and then failing again every time I reinstalled the software to try to solve the problem. Then began a long series of emails with HP technical support. In the next two weeks I have uninstalled and reinstalled the software 6 or 7 times in several different ways, under the instruction of HP. But he never could get Word and Wordpad works correctly. Finally, once again, under order of HP, he worked with a fake installation of HP Deskjet 990c printer. Then I noticed that it was more possible to digitize documents and slides to the computer, except by using a chip memory such as an intermediate storage. Then I went on vacation after spending about 30-40 hours two weeks previous emailing and calling the HP technical support.

  Back from vacation in the third week of October, I took the issue once again with HP support. Yet once, I spent hours and hours writing emails and reinstalling the software but to no avail. HP finally proclaimed this a problem difficult and said that it would increase the level of support. A gentleman named Sylvester who sent someone would phone a day pre-arranged to see more advanced techniques could be applied to the problem. Needless to say that the phone call came not despite my cancelling several meetings to wait in it (I should have better that they had promised to phone back me several times before and has never done).

  Finally, I called customer service to the local office of HP. (At least you can get to them without having to listen to the music for half an hour for the price of 5 p / minute.) They said that they would ensure someone would contact me and would monitor the call to ensure that happened. A week later I ' d has received no call, and I went to the local customer service. Has been raised to the top level of management, and finally, after a few reminders more than me, they managed to get a senior technician, called Natheem, in their technical service Cap to call me.

  He has been very helpful (and actually phoned me several times), and finally he forced me to go through the complicated process of getting Microsoft in India (via a conference telephone with Cape Town and myself - apparently it would have cost me a lot in telephone charges, but I have not had the Bill) to give advice on how to spend my Windows XP with service pack 2 and my internet explore to IE6. I reinstalled the C8180 software once again. No difference, still the same problems, except that now, Microsoft Word would work with the HP C8180 printer driver.

  At this point, Natheem said that it must be a hardware fault and arranged for the device must be replaced.

  The new unit arrived last Thursday. I again carefully uninstalled and reinstalled the software, connected to the machine and got the same problems, but once again with Microsoft Word cannot print with the C8180 printer drivers.

  I tried to contact Natheem again once in Cape Town this afternoon. After half an hour of expensive music additional I have with a person named Waleed who said that Natheem is on a call but he would get to call. No call came.

  So on the forum, I would like advice on what to do with a new HP C8180 All-in-One printer which:

  1. not print Word documents (except by using a printer deskjet 990c driver)
  2. used to scanning documents or transparent to the computer
  3. will not print photos from the computer using HP photosmart essential, or other photo editing software

  I'm also rather fed up of the assistance provided by HP. When you get through them they always try to help, but pass through, especially for someone who knows your case is more frustrating (and costs). In an attempt to get the thing, I also had to downgrade my computer Windows XP service pack 2 OS and my internet explore to IE6. I spent probably 50-60 + hours of the last two months, trying to get the thing work.

  Any advice on what to do next would be welcome.

  BobA

  Hi David,

  Well, my story has a happy ending. I stopped trying to untangle the printer after a whole month of working hours, including a lot of phone calls to the SA and responidng to dozens of emails. But then I bought my wife a laptop Toshiba for Christmas - and it worked perfectly first time. In any case, my computer was in a bit of a mess especially when the messing around I had done on this to HP support, so I decided to reload my operating system (after reformatting hard disk), I just finished. And guess what the C8180 works perfectly (at least until now anyway)! I just updated my OS to SP2 (according to HP support the C8180 has problems with SP3), and I kept my Internet Explorer version 6 (higher versions - 7 I think - again can cause problems according to HP support). I somehow use Firefox. But now its work, its quite an impressive machine.

  I want to say individual personnel in support of HP thin is always very friendly and helpful. It's just a phone, it costs and often listen to music for a long time, its very difficult to get hold of the same person again, if you spend hours to repeat the details of your problem, and despite vehement promises they call you rarely back - probably because they are too busy. His support system which is very poor, not the support staff.

  In any case you have a different problem. If your printer does not work on computers with different operating systems. I would say that you have good arguments to either get a new printer or your money under the guarantee.

  Good luck

  BobA

• problem of download/install HP psc 2355 all-in-one driver

  With the help of the operating system of windows xp with service pack 3. Printer model hp psc 2355 all-in-one. When the driver download/install is done I get the pop-up window

  2.5 FEAD OPTIMIZER.

  "The device is not ready".

  File:C:/Temp/hp_web release

  Error code: 21.1812.01.2.25016

  Please send error to [email protected]

  Using the USB connection method.  I had my computer repaired by Geek Squad and need to reinstall my printer driver. Any help much appreciated. I tried all that I know is not much.

  Hello

  This message is related to the downloaded package that comes with the setup of the netopsystems.com created install creator.

  Solution:
  1. perform an uninstall of level 3.

  1. turn the all-in-one off and disconnect all cable USB/Ethernet of all-in-One to the computer.

  2. Insert the CD-ROM of all-in-one in the computer. Cancel any windows installation that appear.

  3. click on start in the bar of tasks and then run.

  4. in the command box, type command, and then press Next:

  X:\Util\CCC\Uninstall_L3.bat

  (X: is the drive letter of the CD-ROM the CD-ROM of all-in-one is in, if the CD-ROM drive letter is "the command must be D:\Util\CCC\Uninstall_L3.bat)

  2. use the Windows Cleanup utility and remove all entires of netop software systems or HP AiO

  This is the web link to download the "Windows Cleanup utility".

  http://download.Microsoft.com/download/e/9/d/e9d80355-7ab4-45b8-80e8-983a48d5e1bd/msicuu2.exe

  Below listed Remove HP related entries if they are registered.

  The HP Imaging device functions
  Documents HP Viewer
  HP Photosmart Essential
  HP Image Zone
  Gallery HP Photo and imaging
  HP Photosmart, Officejet, Deskjet, or Scanjet, (with the name version number and product software)
  The HP software update
  HP Share on web
  HP Solution Center
  HP Director
  HP memories disc
  Greeting Card Creator 32
  NOTE: Do not remove all the elements other than those mentioned above.

  3. download the package again and re-install.

  Here are the web l ink to download and install the all-in-one software for PSC 2355 all-in-one drivers

  FTP://ftp.HP.com/pub/softlib/software4/COL10513/OJ-30616-1/nn_rub_w01_Americas_Euro1.exe

  Installation instructions:

  (1) disconnect the USB cable from the back of the computer.
  2) double-click the downloaded file and install the all-in-one software, in the middle of the installation, it will prompt you to connect the USB cable then connect it and continue with the installation.

  In my view, these solutions have helped to solve the problem.

  Kind regards.

  Monalisa.

• HP Pavilion 23-B010 all-in-one. How to take back to add more ram. ?

  How to remove the rear while a B010 to access memory and other components.

  Please see upgrade and maintenance Guide for instructions on removing the back of your all-in-one HP Pavilion 23-b010 computer office. Turn the screw counterclockwise until the screws can be removed or 'click' 5 - 6 times!

  If you have any other questions, feel free to ask.

  Please click the White Star of KUDOS to show your appreciation

• Example: Pavilion dv6: printer all-in-one HP PSC 2110

  I, m trying to install the printer all in one HP PSC 2110 on windows 7. Annyone has a compatible driver for this OS.

  Hi @eok001,

  Welcome to the HP Forums!

  I noticed you're wondering if there is a driver available for your printer HP PSC 2110 running on Windows 7. I'm happy to take a look for you!

  A complete printer driver of functionality for one or more versions of Windows is not available for your printer, or from the CD supplied with your printer from the HP website. To use your HP printer with a Windows computer, you must install the driver built-in. To do this, please take a look through this guide, installation of your printer using the built-in Windows driver. Otherwise, I suggest upgrading to a printer of software complete features and drivers available for Windows 7. Here, a list of printers that are compatible with Windows 7.

  I hope this information helps and thank you for posting!

  "Please click the Thumbs up icon below to thank me for having responded."

• Software to scan picture and analysis of documents are missing from the installation of a all-in-one HP Photosmart 2608

  I had installed the software and drivers from the disc that came with the all-in-one multifunction printer HP Photosmart 2608 on Windows XP Home SP2. The menu Manager HP had icons for software photo Scanner and scan a Document and setting options for such software. After I installed SP3 and update the HP software to the latest version (installed by using the full version downloaded from the HP website), these two icons and software are missing by HP Director and as well as the PC.

  I ask that the method to get the software from the HP website and install these software only while the HP Director will fill up with these two icons of software and definition for these two software options can be provided free of charge. Or, please provide me the solution so that these two software installed on my PC.

  Thank you.

  This can help in scanning problems:

  http://support.HP.com/us-en/document/c02114802

  But this document specifically addresses the Director HP scanning:

  http://support.HP.com/us-en/document/bpu00781