Power supply light

Similar Questions

• OfficeJet Pro 8500 a-green power supply light on-Quit printing using as a copier

  I was using the printer as a copier, placing documents on the glass and close the cover.   About 8 different documents, then the printer just quit so that, in the middle of printing a page printed.   Green power light is on, but when I push it, it is not off. Touch control panel does not respond.  Nothing seems to function.   Tried to unplug the power cord at the back, unplug the unit from the wall and disconnect the power supply cord.  Plugged everything back in after about 10 minutes to be disconnected and no help.  Green power light turns on but no function doesn't seem to work.  Have windows 7, 64 bit HP computer, but the copier function should work even if not connected to the computer.

  Appreciate any help.   Thank you

  Carl

  It seems that the firmware may have had a fatal error occurs. I'm afraid there is little you can do to solve the problem. Try the procedure described in the document below. If this does not work, you will need to replace the printer.

  http://goo.GL/aNuHW

• Color Laser Jet MFP M277n Pro: Power supply flashing

  Just set up this printer.  I've not turned off because I think he's using the toner when you next turn on the.  Is this correct?  But now the power supply light flashes.  Is this normal?

  Without doubt, it entered into mode 'sleep'.  Hit the button on the screen which should come on and the power button should now be solid on.

• Dimension 4600 doesn't work with the new power supply

  Hi all

  I replaced the power supply in my 4600 today so he would welcome a Nvidia Geforce 7950GT AGP.

  The model is an integrator of Aerocool 500W 80 Plus Bronze. http://www.Amazon.co.UK/GP/product/B00JKVHKSU?

  The 4600 has two sockets on the motherboard. A 20 pin and 4 pin. The new power supply had a 24pin cable that I shared, so it became 20 + 4.

  It is not working properly. With all the connected cables (2 cables for the mobo) and 2 connectors molex to drive HARD and CD - R, there is a flashing orange light on the front of the computer and a green light on the motherboard. Some discs don't look, no noise. Nothing is on. If I remove the power cable from motherboard 4 pin POWER supply lights up and the fan from the CPU. There is no problem when I connect the old Dell 250w PSU back up.

  Some of the reviews on Amazon have said that some cable has been connected to wrong and only he re-wiring to work. I don't know if this applies to me? I took some pictures of the connectors. http://imgur.com/a/6m9pu

  Someone at - it ideas?

  Thank you

  Andrew

  AV115

  Hi all

  I replaced the power supply in my 4600 today so he would welcome a Nvidia Geforce 7950GT AGP.

  The model is an integrator of Aerocool 500W 80 Plus Bronze. http://www.Amazon.co.UK/GP/product/B00JKVHKSU?

  The 4600 has two sockets on the motherboard. A 20 pin and 4 pin. The new power supply had a 24pin cable that I shared, so it became 20 + 4.

  It is not working properly. With all the connected cables (2 cables for the mobo) and 2 connectors molex to drive HARD and CD - R, there is a flashing orange light on the front of the computer and a green light on the motherboard. Some discs don't look, no noise. Nothing is on. If I remove the power cable from motherboard 4 pin POWER supply lights up and the fan from the CPU. There is no problem when I connect the old Dell 250w PSU back up.

  Some of the reviews on Amazon have said that some cable has been connected to wrong and only he re-wiring to work. I don't know if this applies to me? I took some pictures of the connectors. http://imgur.com/a/6m9pu

  Someone at - it ideas?

  Thank you

  Andrew

  AV115

  Have you used the connector 4 pins, which was part of the 20 + 4 P1 12v connector, connect to the P2 4 motherboard connector pins 12v?

  
  See 41, J5B1 Connector [aka P2]

  http://FTP.Dell.com/manuals/all-products/esuprt_desktop/esuprt_dimension_desktops/dimension-4600_service%20manual_en-us.PDF

  
   http://www.AOne.co.UK/prodinfo.asp?ProductID=4523

  Connector 4 + 4 pin 12v PSU is divided into two 4-pin connectors and one of them, can be used for the P2 motherboard connector.

  Bev.

• Satellite A500 - battery light flashes when connected to the power supply

  Win 7 Satellite A500 PSAM3A-03P00E.

  Battery light flashes when connected to the power supply (intermittent fault), when I disconnect the sector and reconnect the flashing stops and battery (high capacity) continues to receive.

  Also, when battery light blinks the keyboard backlight stays on when it should white and if the backlight is turned off and the battery light starts to blink the keyboard backlight turns on, all other functions seem to work well.

  Charges of battery and the wedges load properly (when the battery flashes).

  Hello

  Have you noticed this problem since the first day of purchase?
  Theoretically, it could be possible that your battery begins to malfunction
  On the other hand, an electrical problem could also be possible

  However, try this:
  Remove the battery and the AC adapter. Then press and hold button power 30 sec long.
  Then insert the battery and plug AC adapter still does that help?

  By the way: this is the BIOS updated? If this isn't the case, perform an update.

• The green light on the power supply shuts off when I try to turn on my pc to my thought is a power supp

  The green power light on the power supply shuts off when I press the power button / stop on the fron of the pc.  I think power but would it be the switch?

  It is a sign that the PSU has failed, but here's a convenience store. If you had mentioned the model #, I could have linked a suitable replacement.

  http://support.HP.com/us-en/document/bph06788

• Satellite L300 - transformer power supply makes light rattling

  Hi, thanks for reading.

  Recently, I noticed that when my laptop is connected to the power supply, the transformer makes a slight sound of rattling, just loud enough to be heard on a movie running at full volume, but not loud enough to be heard unless you look for it.
  The click is sporadic and does not seem to relate to what is happening on the laptop.
  I said it could be an overheating problem, but I've had the laptop for a couple of months and longer, I have instructed to at the same time is 8 hours.

  It doesn't seem to be any negative effect on the computer, but it made me a little worried.

  Thanks for your help,
  Marlon

  If a technician can open your adapter, it will find a burned capacitor "the biggest one" change

• G4 MDD power supply Issue

  My MDD was recently stop only two or three minutes after a cold start. The power led lights up, the gray screen with the Apple logo appears with the spinning wheel, but then the machine suddenly loses power as if the power cord was disconnected. These are the things I've already tried:

  1. Removed the PRAM Battery
  2. Disconnected all devices except the keyboard and the monitor
  3. Tried a different power cord

  Start in safe mode did not help. The fans are all running, the red LED lights on the logic board and disk drives seem to work. This could be a power supply issue or a problem with the motherboard and is it possible that I can definitely identify the problem without being able to start the G4? The startup time has been considering more when everything worked last week, would that be a clue? I've owned this machine for more than twelve years and it put to the test so I wonder if it's time to retire him.

  Thanks in advance for any help you can offer!

  Hi, looks a lot like a problem of heat from the CPU, thermal paste is usually good for 5 years or more.

  It runs longer open door?

• Power supply for Powermac MDD

  Hey all,.

  I got a Powermac MDD dead sitting in my room for a few years now that I picked up for free because it lights. I came to the conclusion that it was the power supply, so I took and threw it years. Now, here I am, no power supply and one useless MDD.

  I really want to get this thing to the top and running, but as the price of the power supply on ebay are absolutely ridiculous. I hope that someone here has a job, they are willing to participate with and sell to me. (Pay me for the part + shipping costs). Also interested in an OS disc that will work for the machine, so I can stand him up and running.

  If eBay is too pricing heartburn, try a Mac (MUG) user GFroup in your area. This site will help you locate a:

  http://appleusergroupresources.com/find-a-group/

  As a general rule, you don't have to physically visit the groups for assistance. Several times, simply by sending an e-mail "looking to buy" published groups addresses will receive a response.

  The other option is to look for a private LABEL job and use it for parts. The cost of a scrap computer may be less than the PSU.

• Power supply for my P7-1410 with 16 GB of RAM

  Hello

  I installed my new GEFORCE GTX650 video card in my HP Pavilion P7 1410 with 16 GB of RAM.  Is it my PC to handle the EVGA-SuperNOVA NEX750B 750W power supply?  Is this too much for this model?

  Thank you

  WND

  Hello

  You may need to use a shoehorn so he can adapt.  The physical dimensions of a standard power SUPPLY HP block is 5,9 "x5.5"x3.4. The Corsair CX600 or CX500 would be better physical shape.  Some of the older PC HP lights with blocks of power more than 650 watts.

• Satellite x 200 battery or power supply issues

  I have a satellite x 200 - s20. Owner since new, 2 and a half years.
  The laptop works perfectly, but I don't know if I need a new battery, power or maybe there is a hardware problem (but I doubt it).

  When it is connected to the power outlet, provide the following happpens:

  He started using the battery instead of the power supply.
  Power and battery leds turn on and turn off (on during a few seconds and then off for a few seconds).
  At this point, the battery stops charging.

  In the manual it mentions something on one of the lights turn blue, none have ever done that.

  Hope someone can advise
  Thank you
  Strand

  Hello

  In my opinion, you should first check if the power adapter is not a malfunction.
  If the AC adapter would work properly, then the battery might not be charged and the battery led not turn to blue because the battery is not fully charged.

  I would recommend so check the AC adaptor first.
  Of course this is only my personal opinion and I could be wrong too

• Tecra M9 - no power orange light error code sequence

  Hello

  I have a Tecra m9 laptop and when I try to turn it on, it blinks with a light orange in this sequence:

  6 short flashes, short 1 long blink, 1 blink, a ditch, and then it repeats.

  Does anyone know what is the problem?
  Any advice would be greatly appreciated.

  See you soon.

  What you see flashes code. The flashing provides an error code. Short means 0 and 1 long.

  The hexadecimal code can be read by the service partner. The blink code will be sent when the microcontroller detects a problem with the power supply. Unfortunately you can not do anything alone. Contact the closest partner in your country and ask for help.

  All you can try right now is to disconnect battery and start the laptop with AC power only.

• With Tecra750DVD power supply problem

  My laptop recently decided to refuse to turn on when I turned on. There is a yellow light in the position of "power" over the front of the machine, but it won't start. I tried all the options: Power Supply Unit only, only battery, Power Supply Unit + battery and nothing works. Fuse is good in the plug of power supply. Battery is less than 12 months.

  Hello

  You can remove the battery completely when problemshooting this kind of predicament.

  First of all - what impression the power button? Does it feel as it should? Refers to how it used to feel? If this is not the case, check if there is an active "lock" behind it.

  Some models have a safety lock to keep the machine from accidentally start in a bag or two.
  Please look at the LED that indicates that your adapter is connected. When you try to switch the machine on, what is happening with this LED? Always the same fixed green light or suddenly out or flashing?
  If out, please try to get your hands on another adapter (borrow prefferably). If it flashes then try to remove the AC adapter, remove any option that can be easily removed, CD/DVD, memory, expansion card PC and so on.
  Try to restart it (remember to join HQ again). Even? If Yes, then sorry to say I think that your machine needs service. If this isn't the case, then there could be hope.

  Disconnect the AC and put back in place the units that you have deleted before, one by one and after each unit, try to restart the machine.
  If it starts fine, remove the unit and reconnect the next unit. Perhaps you will find that there is a problem with an external device (memory, CD, PC Card and so on), then at least you can continue working more or less as before the problem.

  Good luck

  Tom

• Corsair POWER supply update does not post, powers of the powers of 5 seconds down and loops...

  Have the HP Pavilion Elite m9650f with motherboard replaced in April 2012 class good to go.

  Replaced the stock GPU Nvidia GeForce 9800 GT with a Zotac GTX 560 Ti GPU and

  the stock HP 460 Watt power supply with a W0388RU Thermaltake TR2 600 Watt PSU in may 2012.

  All goes well until October 2012.

  PC randomly starts shutting itself off the coast and not feed until I have unplug the power cord and wait 5-10 minutes.

  Finally, he stopped turning on all together.  Reinstall all power PSU connectors, etc.  same result.

  Removed all cards, etc, same result.  Cards reinstalled one by one, etc., same result.

  Reinstall the stock HP 460 Watt PSU, now everything works fine.

  Thought it was a premature failure of Thermaltake PSU.

  Bought and installed a Corsair CMPSU - 850TXV2 850 Watt power supply for a few days but still not good to go.

  Lights, fans spin, but no MESSAGE, no video, tracks for all

  5 seconds, stops, turns on itself over and over again.

  Reinstall all power PSU connectors, etc. same result.

  Removed all cards, etc, same result.  Cards reinstalled one by one, etc., same result.

  Reinstalled the HP PSU stock, now everything works perfectly again.  ?

  Spends hours reading the forums...

  Some say that the RAM may not report correct voltage for power supply.

  If so, what can I change RAM voltage in the BIOS?

  Others say reset CMOS I did, same result.

  And someone on this forum HP thought that perhaps the Pegatron IPMTB-TK

  Card mother Truckee can only accommodate up to 750 Watts POWER supply.

  Any ideas?

  Can I get away with just using my HP 460 Watt power supply after all stock?

  Thank you.

  I have an additive to add to this topic.

  To refresh, my questions focus on a possible shift of the power supply and card mother specs:

  What is an ATX 12 v 2.0 and above technical problem or a power CAP problem?

  I posted my questions on the Forum of power SUPPLY Corsair PSU

  at the same time and I paste it here now, a response

  to GUY of RAM.

  "Hey RAM GUY."
  
  Sorry I couldn't answer until now.
  
  Please specify the difference between the ATX 2.0 specification and 2.01
  
  Spec that the negative - 5 v Rail is not present in the 2.01 spec and
  
  beyond.  As I mentioned previously, the Thermaltake PSU that has been
  
  running in my 2009, HP i7 tour for 7 last month said 12 volt ATX 2.2
  
  on the case and even if the power supply HP OEM said 12 volt ATX
  
  2.0 in the technical literature, that I found on Google, the real PSU I have does not work
  
  have any note on the case ATX specification.  So I think it's safe to say, my
  
  motherboard does not have the negative Rail v-5 at which he played
  
  nicely with 12 volt ATX 2.2 spec, until recently.
  
  Although theoretically it is supposed to be no limit on the amount of
  
  Absorbed power, you can use to power your motherboard, the motherboard because
  
  is supposed to use only what suits him and cap the rest, it seems that the OEM
  
  can dial up limitations of power if they deem necessary.
  
  Could be as simple HP, without wanting to compete with some of his HPs
  
  Professional workstations, caps so power on some Pavilion Elite
  
  Series models to prevent them from becoming a much cheaper
  
  solution.
  
  In any case, I think that all the available information, digested, he does not speak
  
  Specification of the ATX, but rather my motherboard HP has a limit of 650 Watts of power
  
  If I think that I read that someone else got the same motherboard goes with
  
  750 watts, but I do not remember where to find this announcement. »
  
  I'm back and Yes!
  
  Thanks again Lasvegaswireman!

• On Satellite P100 power supply problem

  Hai
  I bought the new laptop Satellite P100. Suddenly it does not start (no power to notebook) and the same time, I have only checked by the only power a/c no result, also do not charge the battery. I put t know what is the reason. Can someone give suggestion?
  Thank you bye.

  If the power light is blinking there is probably a problem with the electronic power supply. In this case, the laptop sends flashes code. Read this code, technicians can identify the problem.
  Please, don't waste your time but the closest service provider contact allowed in your country.
  After 18 months of that guarantee must be valid (it depends of course on where you live) as well as the repair must be free.