PowerConnect 6224 piling on XFP

Hi all

Just curious about something I've been trying to find a hard yes/no answer on but have had no luck.  Long story short, I'm looking to pick up a pair of 6224 switches and would set up in a pile.  I'm looking at the use of fibers to connect and wonder if the switches will allow me to configure FJ727 XFP modules for stacking or if they will only help stacking if you use the CX4, UY108 or GM765 modules for stacking.

My other question is that if I can use the XFP module for stack, it will force the XG1 and XG2 XFP module to use for the stack, or can I configure a port for stacking and the other for a 10 GB uplink to my router?

Joekamel,

Only CX4 modules can be used for stacking on the PowerConnect 62xx switch.  You can find more information about all the modules supported for the 62xx under 'N-Series Switches of Campus' at the following link.

http://en.community.Dell.com/TechCenter/networking/p/guides

If you download the file called 'Expansion Modules for network switches Dell' and go to page 17, it it shows all five supported modules and shows only CX4 to stacking.

B

Tags: Dell Switches

Similar Questions

  • VLAN between 2 powerconnect 6224 using XFP modules

    Dear friends,

    I have 2 switches powerconnect 6224 interconnected using optical fiber and XFP ports on the rear panel of the switch.

    There is no configuration of the battery between them.

    The distance between the two switches is 500 metres and they both work correctly when you use the vlan by default (use of the LAN)

    I created a virtual LAN using 2 ports on a firewall and I created the same vlan on the second firewall, but I can't see a VLAN traffic goes to the other.

    Also, I tried to configure the port as trunk but same result.

    The vlan works very well in a single switch, but traffic is not able to flow to the second switch.

    You have an idea why does not?

    Maybe is not posible to have VLANs using xfp connections...

    Any idea would be greatly popular.

    Thanks in advance!

    Rear ports are labeled xg1, 2, 3, 4. So, if the connection is made using the xg1 on a single switch for xg1 on the other switch. Then you enter interface 1/xg1 and make configuration changes.

  • How Reboot/restart Dell Powerconnect 6224

    Hello

    My company has 2 powerconnect 6224, 1 is the master and 1 slave, do I know how could restart/reboot my switch in the GUI?

    Can I use the cli to restart/reboot command and what is the command line.

    Thank you

    Using the CLI to recharge the battery, you must use the # reload command. You can add the number of the switch in the command reload members of chimneys. charge # 1, # reload 2.

    You can also use the command console (config-battery) #initiate failover. This command forces a warm restart of the battery. The unit of backup succeeds the new management unit without clear status of material on the stack members. The original management unit restarts.

    In the graphical user interface, you can reboot the switch with entering the system > general > reset. You can also start a recovery using System > stacking > NSF summary. Initiate failover will begin a warm reboot of the switch.

  • LACP LAG POWERCONNECT 6224

    Hi I m ussing a powerconnect 6224, I have equipment that works as a switch and it has two ports glued with LACP, when I connect this device to the POWERCONNECT and send a ping there is no answer, one that with a laptop computer connected to this port, it responds to the ping command. Can help you with this? Here is the configuration of the POWERCONNECT. Thanks in advance.

    Console (config) #interface vlan 32

    Console (config-if-vlan10) #ip address 10.163.101.4 255.255.255.252

    Console (config-if-vlan10) #routing

    Console (config) #interface ethernet 1/g3

    mode console (config-if-1/g1) #switchport general

    Console (config-if-1/g1) #switchport general allowed vlan add 31

    Close, more like this.

    Console (config) # interface range ethernet g2

    Console # channel - group 1 automatic mode

    output console #.

    Console (config) # interface range ethernet g3

    Console # channel - group 1 automatic mode

    output console #.

    Console (config) # interface port-channel 1

    Console # switchport mode general

    Console # switchport general allowed vlan 201 tagged

    Make sure that there are at least two ports in each LAG.

  • PowerConnect 6224: Dell SFP + port supports combine Dell SFP?

    I have a Dell Powerconnect 6224 switch and I installed a Dual Port SFP + Module of adaptation for PowerConnect
    6200 series at bay2 at the rear of the switch. I inserted a transceiver, SFP 1000BASE-LX, wavelength 1310nm 10km Reach in the SFP slot + and the other end is connected to a connector SFP 1gbe. I don't have any link. My question is if Dell SFP ports + supports SFP transceivers or it only supports SFP transceivers +?

    I checked the ports to help an SFP + SFP +, 10GbE, copper Direct Attach cable Twinaxial, and link LEDs are lighting up.

    I believe that the SFP ports + back work with SFP transceivers. Ports before combo will work with SFP transceivers. Another thing to look at is the cable being used. Don't forget that there are specifications that are compatible with transceivers FPS are you wanting to use. A SFP + SFP connection would require that the SFP transceiver + supports a connection of 1 GB.

    Hope this info helps.

  • Slave keeps restarting after unstacking-Dell PowerConnect 6224 switch

    Hello everyone;

    I have 2 switches (PowerConnect 6224) on the other. Because we are them stacked like we got new switches, we decided to remove the cables from the battery and use them as individual switches.

    So I tried to unstacking the first switches using CLI, but it does not, simply, nothing happens. So I took the cards accumulation off both switches and removed the stacking cables.

    Switch works fine, but the slave is restarted.

    I correct the following:

    Startup options, tried to reset, restore the production parameters, format... They look successful the config looks like this is done and once the switch starts it asks me if I want to run the Setup Wizard, but it will just freeze and restart.

    is there a way to fix it? or the switch is dead?

    All ideas are welcome

    Thank you

    I would like to download the latest firmware.

    www.Dell.com/.../drivers

    Disconnect all other devices from the switch and follow the instructions of XMODEM that are included in the download to Flash the firmware.

  • Good method to restore running, boot and Firmware for PowerConnect 6224 switch

    Hi all

    I have a switch PowerConnect 6224 of production that is configured exactly as I want.  I have a new PowerConnect 6224 switch I want to restore the config is possible?  My goal is to not have to manually enter settings for each single switch.

    I tried a few methods, but they do not seem to work.  If anyone can tell me the correct procedure or point me in the right direction would be great!

    Here's a document on some older switches which explains the process.

    www.Dell.com/.../app_note_12.pdf

    It is different for the 6248 somewhat, but the concept is still the same.

    Copy of the file Image of a server to Flash memory

    Use the command copy of the image - the url of the source to copy an image from a Flash memory server file, use the boot system command to activate the new image.

    Copy of a Configuration file from one server to the running Configuration

    Use the running-config command to copy the url of the source to load a configuration file to a network server for the device running configuration. The configuration is added to the running configuration, as if the commands were typed in the command line interface (CLI). The resulting configuration file is the combination of the running configuration and the loaded configuration file, with the configuration file with priority.

    Copy of a Configuration file from one server to the Startup Configuration

    Use the command copy startup-config - the url of the source to copy a configuration of a network server file in the startup of the device configuration. These commands replace the configuration file starting with the copied configuration file.

    Store the Configuration of starting or running on a server

    Use the command copy running-config destination url to copy the current configuration file to a network server by using TFTP. Use the copy destination-url startupconfig command to copy the configuration file to start on a network server. The copy of the configuration file can be used as a backup copy.

    firmware download also includes step by step instructions on how to upgrade the firmware.

    www.Dell.com/.../drivers

  • Proxy-arp or local proxy arp? Reference Dell Powerconnect 6224

    We need allow some customers to resolve the mac address of a server that is located in a different range of addresses, VLAN and IP.

    I thought that the addition of the ip proxy-arp interface command vlan should do the job, but this command seems to be activated by default according to the reference guide, after that I tried to add the command he always show up on a running show. Which confirmed my thoughts. While I was looking for the solution that I saw another command that does not appear in the cli reference guide: local-proxy-arp ip. But since I'm not sure of what will make this command I am careful to hit just the command on the interface VLAN.

    How others send their arp on powerconnect 6224 requests?

    After reading my own source again, I realized that the thing that I want is not possible. It goes beyond the need to divide the network into segments. If all the query arp is transferred to other networks, there is a benefit less: you want to limit the broadcast domain.

    Static ARP is the thing I'm going to need to be implemented to solve this problem.

    Thanks for the clarification anyway.

  • PowerConnect 6224 VLAN created, but impossible to do a ping between customers

    1 created vlan 2 with two ports 17.19 with ip 10.0.1.2/24

    2 created vlan 3 with two ports 13.15 with ip 10.0.2.2/24

    attempt to create inter routing vlan

    1 pc windows connected with ip 10.0.1.3/24 and a gateway to port 17 10.0.1.2

    2 connected windows pc with ip 10.0.2.3/24 and a gateway 10.0.2.2 to port 15

    Unable to get the Ping between two clients any help would be much appreciated, thank you in advance and running config pasted below

    coresw1 #show running-config
    ! Current configuration:
    ! Description of the system "PowerConnect 6224, 3.3.7.3, VxWorks 6.5.
    ! 3.3.7.3 system software version
    ! Passage mode is configured as disabled
    !
    Configure
    database of VLAN
    VLAN 2-3, 5
    VLAN 2 1 routing
    VLAN 3 2 routing
    output
    location of SNMP Server "Data Center"
    contact SNMP Server «»
    hostname "coresw1".
    unicast SNTP client enable
    10.0.0.1 SNTP server
    clock timezone 5 minutes 30 zone 'IST '.
    battery
    1 1 member
    output
    IP 10.0.0.193 255.255.255.0

    by default-gateway IP 10.0.0.1
    IP - peekaygroup.com domain name
    name-server IP 10.0.0.1
    without enabling ipv6
    IP routing
    interface vlan 2
    name "LAN1.
    Routing
    10.0.1.2 IP address 255.255.255.0
    bandwidth 10000
    IP mtu 1500
    output
    interface vlan 3
    name "LAN2.
    Routing
    IP 10.0.2.2 255.255.255.0
    bandwidth 10000
    IP mtu 1500
    output
    interface vlan 5
    name "RIL Internet"

    output
    level of 8a9f2a72d65baf40b48108874cd50592 user name 'admin' password encrypted 15
    !
    interface ethernet 1/g13
    switchport access vlan 3
    output
    !
    interface ethernet 1/g15
    switchport access vlan 3
    output
    !
    interface ethernet 1/g17
    switchport access vlan 2
    output
    !
    interface ethernet 1/g19
    switchport access vlan 2
    output
    !
    interface ethernet 1/g20
    switchport access vlan 5

    output
    !
    interface ethernet 1/g22
    switchport access vlan 5
    output
    SNMP-server community public rw
    output

    This blog does a good job of showing the different firewall rules to add. You said that you have already tweaked the firewall some, I would just check the measures taken.

    http://www.sysprobs.com/enable-ping-reply-Windows-7

    If there is no antivirus software installed, try a break/disabling it to test and see if it makes a difference.

    I don't see anything on the config which would prevent pings happen.

  • How to access the management of VLANs with a different virtual LAN (Dell powerconnect 6224)

    Hello

    DELL powerconnect 6224 reference.

    I want to access the management of a different VIRTUAL LAN VLAN.

    The management of VLANS is 100 of VLAN. not the routing

    My computer is vlan 60 (192.168.60.10) and I want to connect via ssh or http (192.168.100.1) to manage my switch.

    Thank you for your help on the command line

    The management of VLANS on the 6224 is not routable. So, you will not be able to access VLAN 100 from any other VLAN. However, you can manage the switch from other VLAN IP addresses. So if VLAN 60 has an IP of 192.168.60.1 you can http and ssh to it. And if the VLAN routing is enabled you have access to 192.168.60.1 on the other VLAN.

    See you soon

  • Transit VLAN on the PowerConnect 6224

    I need help to sort out a problem with routing on a 6224 we have configured to act as a vlan transit for one of our branches.  The general idea is 8.143 is the vlan of transit, of 8.144 is our PC LAN 8.145 will be our VOIP lan.

    We have installed this switch with our WAN provided last week, but had to get out. Traffic seemed to happen to the WAN providers to our transit interface VLAN (172.22.143.254) wasn't going anywhere.  It's symptoms

    (1) we could ping from 172.22.144.x to 172.22.145.x and 172.22.143.x

    (2) we could ping from 172.22.145.x to 172.22.143.x and 172.22.144.x

    (3) we could ping from 172.22.143.x to 172.22.144.x and 172.22.145.x

    (4) if I was plugged into the 6224 on with an address 143.x I could ping our remote control does site at 172.22.8.x no problem but not 144.x or 145.x

    (5) 172.22.8.x, I couldn't ping 144.x or 145.x or 143.1 (I could ping 143.254 which is EXTENDED to suppliers to our switch network interface)

    Here's the running to the switch configuration.  Any suggestions would be greatly appreciated:

    Console > activate

    Console execution #show

    ! Current configuration:

    ! Description of the system "PowerConnect 6224, 3.3.6.4, VxWorks 6.5.

    ! 3.3.6.4 system software version

    ! Passage mode is configured as disabled

    !

    Configure

    database of VLAN

    VLAN 143-145

    VLAN routing 143 1

    VLAN routing 144 2

    VLAN routing 145 3

    subnet of VLAN association 172.22.143.0 255.255.255.0 143

    subnet of VLAN association 172.22.144.0 255.255.255.0 144

    subnet of VLAN association 172.22.145.0 255.255.255.0 145

    output

    battery

    1 1 member

    output

    DHCP IP address

    IP routing

    IP route 0.0.0.0 0.0.0.0 172.22.143.254

    interface vlan 143

    Name the "Transit".

    routing ip address 172.22.143.1 255.255.255.0

    output

    interface vlan 144

    name "TWLAN".

    routing ip address 172.22.144.1 255.255.255.0

    output

    interface vlan 145

    the name "VOIP" routing

    IP 172.22.145.1 255.255.255.0

    output

    level of 746f7a78621059d80fdc538acc40cbf2 user name 'admin' password encrypted 15

    !

    interface ethernet 1/g1

    switchport mode general

    VLAN allowed switchport General add 143

    output

    !

    interface ethernet 1/g2

    switchport mode general

    VLAN allowed switchport General add 143

    output

    !

    interface ethernet 1/g3

    switchport mode general

    VLAN allowed switchport General add 144

    output

    !

    interface ethernet 1/g4

    switchport mode general

    VLAN allowed switchport General add 144

    output

    !

    interface ethernet 1/g5

    switchport mode general

    VLAN allowed switchport General add 145

    output

    !

    interface ethernet 1/g6 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g7 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/8 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g9 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g10

    switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g11 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g12 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g13 switchport mode General General switchport vlan allowed output adds 145! General mode of interface ethernet 1/g14 switchport

    switchport general allowed vlan add exit 145! interface ethernet 1/g15 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g16 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g17 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g18 switchport mode General switchport General allowed vlan add 145

    output! interface ethernet 1/g19 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g20 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g21 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g22 switchport mode General switchport General allowed vlan add exit 145

    ! interface ethernet 1/g23 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g24 switchport mode General switchport General allowed vlan add to exit 145

    Console #.

    It seems that port 1 must be in the VLAN 143, not general mode access mode. You already have a static route in place on the PowerConnect switch which directs traffic to the next break in the network. But it may be necessary for a place on the Cisco that allows to direct traffic to the PowerConnect switch.

    Here is a good post to look through also.

    http://en.community.Dell.com/support-forums/network-switches/f/866/t/19506015.aspx

  • Update Firmware on Powerconnect 6224 switch

    I am wanting to update the firmware on my Powerconnect 6224 3.3.1.10 Version 3.3.5.5 Version switch.  Is there a problem with this jump or if that's okay?

    I would like also some words of wisdom as how this upgrade as painless as possible.

    Sincerely,

    Ken

    You should not have problems from this version to the current 3.3.5.5.  If you are not familiar with the command line on the switch, you can download the firmware from a location on your workstation management through http.

    You start by downloading the 3.3.5.5 from the support.dell.com site. Keep in a folder.  Then from the interface WebGUI of the switch, you can go to System/file/management folder download you must choose HTTP to transfer mode, then navigate to the location of the firmware on the desktop you.  Here is a screenshot of the file download page.

  • I need manage the bandwidth used, PowerConnect 6224 traffic collision and packet traffic.

    I need manage the bandwidth used, PowerConnect 6224 traffic collision and packet traffic. I downloaded the MIB from the Dell support site and I saw thar there are about 105 MIB in the downloaded file. My question is: in what Mib, I can find the OID which allow me to monitor the above?

    Thanks in advance

    Rogerio

    Unfortunately, there is not a complete list of the different OID in different MIB. In order to find this info to simply browse through the different MIB seeking the OID, you need. We did some looking through the MIB and found these OIDs that can help you. Another thing to keep in mind is that the MIB downloaded are in general of a group of switches. So there are situations where a /OID MIB listed will work for a certain model of switch with certain level of firmware.

    RMON-MIB

    FastPath-cos-qos-mib

    Another method, some people have had success, done using a SNMP walk.

    http://www.snmpsoft.com/freetools/snmpwalk.html

    I hope this information helps. The method of importation for these MIBs can change based on the management/tracking software that you use.

    Thank you

  • Port mirroring for the uplink of 10 GB of PowerConnect 6224

    I need to take a copy of the traffic over a 10G fiber link. The amount of traffic on this link is less than 1 Gbps.

    I am considering using the mirror port on a PowerConnect 6224 for this function. However, I don't know if port mirroring also works on the links to the top of the switch.

    Anyone know if a port 10G uplink on the 6224 can be mirrored on one of the 24 Gigabit Ethernet ports?

    I've been the mirror of able port of a fibre port with an Ethernet port, following the instructions on page 333 of the owner's manual.

    http://support.Dell.com/support/eDOCS/network/PC62xx/en/UCG/ucg_en.PDF

    He took it and did not return any errors. But I see potential for some issues if the fiber port went above 1 Gbps.

    Keep us updated and let us know what are your conclusions.

    Thank you.

  • PowerConnect 6224 Switch Netgear L2 and

    Hi, I have now successfully configured my PowerConnect 6224, host and road between the 4 VLANS, I have access to the internet and can ping I have, is all great work. The next thing on my list is to set up my router L2 netgear to work with the port based VLAN, I want to connect L2 switch port 1/g23 on my PowerConnect 6224, as far as I understand this port must be a trunk port allowes all WHAM, here's them my config for the PowerConnect 6224:

    ! Current configuration:
    ! Description of the system 'Dell 24 ports Gigabit Ethernet, 2.0.1.8, VxWorks5.5.1'
    ! Version of the software system 2.0.1.8
    !
    Configure
    database of VLAN
    VLAN 10,20,30
    subnet of VLAN association 192.168.1.0 255.255.255.0 1
    subnet of VLAN association 192.168.2.0 255.255.255.0 10
    subnet of VLAN association 192.168.20.0 255.255.255.0 20
    subnet of VLAN association 192.168.30.0 255.255.255.0 30
    output
    battery
    1 1 member
    output
    1 priority 1 switch
    IP 192.168.1.1 255.255.255.0
    IP - xxx.xx.xx domain name
    Name 192.168.2.10 IP-server
    IP-name 192.168.2.30 Server
    IP routing
    IP route 0.0.0.0 0.0.0.0 192.168.2.201
    bootpdhcprelay enable
    bootpdhcprelay IP_serveur 192.168.2.10
    bootpdhcprelay cidridoptmode
    192.168.2.1 IP helper-address 192.168.2.10 37
    192.168.2.1 IP helper-address 192.168.2.10 49
    192.168.2.1 IP helper-address 192.168.2.10 137
    192.168.2.1 IP helper-address 192.168.2.10 138
    IP helper 192.168.20.1 192.168.2.10 37
    IP helper 192.168.20.1 192.168.2.10 49
    IP helper 192.168.20.1 192.168.2.10 137
    IP helper 192.168.20.1 192.168.2.10 138
    IP helper 192.168.30.1 192.168.2.10 37
    IP helper 192.168.30.1 192.168.2.10 49
    IP helper 192.168.30.1 192.168.2.10 137
    IP helper 192.168.30.1 192.168.2.10 138
    interface vlan 10
    "Name servers".
    Routing
    IP 192.168.2.1 255.255.255.0
    Send IP rip rip1 version
    IRDP IP
    output
    interface vlan 20
    the "sale".
    Routing
    address 192.168.20.1 255.255.255.0
    Send IP rip rip1 version
    IRDP IP
    output
    interface vlan 30
    name 'accounts '.
    Routing
    192.168.30.1 IP address 255.255.255.0
    IP netdirbcast
    Send IP rip rip1 version
    IRDP IP
    output
    level password user name 'michi' encrypted 15 4f70cfb1451a1b0ce0b872421bee6c1c
    !
    interface ethernet 1/g1
    switchport mode general
    pvid switchport General 10
    No switchport acceptable-framework-type general tag only
    VLAN allowed switchport General add 10,20,30
    output
    !
    interface ethernet 1/g3
    switchport mode general
    pvid switchport General 10
    No switchport acceptable-framework-type general tag only
    VLAN allowed switchport General add 10,20,30
    output
    !
    interface ethernet 1/g4
    switchport mode general
    switchport General pvid 20
    No switchport acceptable-framework-type general tag only
    VLAN allowed switchport General add 20
    output
    !
    interface ethernet 1/g5
    switchport mode general
    pvid switchport General 10
    No switchport acceptable-framework-type general tag only
    VLAN allowed switchport General add 10,20,30
    output
    !
    interface ethernet 1/g7
    switchport mode general
    pvid switchport General 10
    No switchport acceptable-framework-type general tag only
    VLAN allowed switchport General add 10
    output
    !
    interface ethernet 1/g8
    switchport mode general
    switchport General pvid 30
    No switchport acceptable-framework-type general tag only
    VLAN allowed switchport General add 30
    output
    !
    interface ethernet 1/g23
    switchport mode trunk
    switchport trunk allowed vlan add 1,10,20,30
    output
    !
    interface ethernet 1/g24
    switchport mode general
    pvid switchport General 10
    No switchport acceptable-framework-type general tag only
    VLAN allowed switchport General add 10,20,30
    output
    output

    On my netgear L2 switch that I want to connect the port 24 to 1/g23 of my Dell switch, but I can't seem to be able to make it work somehow, here is my config to the Netgear switch:

    ! Current configuration:

    !

    ! Description of the system "GSM7224 L2 managed Gigabit Switch"

    ! Description of the system 6.2.0.14

    !

    Quickly define "GSM7224.

    Network Protocol No

    network settings 192.168.1.2 255.255.255.0 192.168.1.1

    database of VLAN

    VLAN 10

    10 name servers of VLAN

    VLAN 20

    name of VLAN 20 sales

    VLAN 30

    name of VLAN 30 accounts

    output

    Configure

    clock timezone "GMT" 0 0

    SNTP client unicast mode

    ! The SNTP server is active

    Server SNTP PooleOne.xxx.xx.xx

    set logging in buffered memory

    lineconfig

    output

    Storm-control flowcontrol

    name of the configuration of protocols spanning-tree 00-0F-B5-FC-BA-62

    public@10 SNMP-Server community

    public@20 SNMP-Server community

    public@30 SNMP-Server community

    IP - xxx.xx.xx domain name

    Name 192.168.2.10 IP-server

    192.168.2.30

    192.168.2.201

    interface 0/1

    pvid VLAN 10

    participation of VLAN include 10

    output

    interface 0/2

    pvid VLAN 20

    participation of VLAN include 20

    output

    interface 0/3

    pvid VLAN 30

    participation of VLAN include 30

    output

    interface 0/4

    output

    interface 0/5

    output

    interface 0/6

    output

    interface 0/7

    output

    0/8 interface

    output

    interface 0/9

    output

    interface 0/10

    output

    interface 0/11

    output

    interface 0/12

    output

    interface 0/13

    output

    interface 0/14

    output

    interface 0/15

    output

    interface 0/16

    output

    interface 0/17

    output

    interface 0/18

    output

    interface 0/19

    output

    interface 0/20

    output

    interface 0/21

    output

    interface 0/22

    output

    interface 0/23

    output

    interface 0/24

    Description "Trunk Port.

    marking 1 VLAN

    participation of VLAN include 10

    VLAN tagging 10

    participation of VLAN include 20

    VLAN tagging 20

    participation of VLAN include 30

    VLAN tagging 30

    output

    output

    First; is it possible to achieve what I'm trying to do with my equipment?

    Second; where I went wrong in my configs?

    Thank you very much for your help.


Maybe you are looking for

  • iCloud library always up-to-date!

    Hi guys,. I have an iPhone 6 and I started using icloud library recently. I turned on icloud photo library on my iphone and the photos were perfectly sync with icloud. Later, I've disabled icloud photo library on my iphone and uploaded a few photos t

  • OMG Skype is driving me crazy! No video

    I found that some archived messages but nothing recent. McBook Air + OSX 10.11.02 = Alexander-Graham-Bell Built in camera does not work with Skype. Any suggestions? Stealth

  • SD card does not work on Tecra A9

    Hello The * SD reader * does not appear on ' * Workstation ' * until I have insert a * SD *.It appears so. However, when I try to * read * it I get the message ' * insert disc in drive E:'*. Someone at - he encountered this before? Thank you John

  • Trying to create the recovery USB disk

    I am trying to create a usb for my yoga 2 pro recovery disk. I found the instructions of lenovo support page, but when I search "recovery disk", nothing comes. Does anyone know why this might be?

  • Windows Installer insist on not requested installation applications

    WINDOWS INSTALL CONTINUES TO APPEAR TO SUPPORT APPLICATIONS WHEN THE COMPUTER STARTS. IT IS INCESSANT AND ANNOYING. ONE OF THE MESSAGES THAT EMERGES IS: THE FEATURE YOU ARE TRYING TO USE IN A CD-ROMM... IT IS NOT AVAILABLE.