PowerConnect 6248P 10 G SFP + compatibility

Similar Questions

• Update firmware on Dell Powerconnect 6248P battery

  Hello

  I need to update the firmware on the switches on my stack, the stack consists of 3 all current 6248P to run version firmware 3.2.1.3 Powerconnect switches.

  I plan to stack in a 4 switch that is running 3.3.1.10 so I need to update my existing carpet before doing this.

  I would like to use auto update and upgrade the firmware on the circuit breaker that will modernize, then the rest of the stack, but the issue I'm having, it's that the documentation Dell tells me to enable synchronization of the firmware using the command "start auto-copie-sw" in the cli, however appears not to exist at all?

  Can someone advise?

  Thank you

  Steve

  The documents listed here.

  www.Dell.com/.../pwcnt_stacking_switches.pdf

  Is a little outdated. Therefore, the listed order is more part of the 6200/CLI firmware. By default, the switch will try and push any updated firmware for the other switches in the stack, no need to run a command.

  See you soon.

• Reference Dell 6248P - Guest Wifi VLAN config

  I am trying to retrieve all upward of a VLAN. The VLAN is comments wireless traffic going through our main switches and on an ADSL router but I'm running into some difficulties.

  We have 3 points of access for model AP - AC Unifi. Each access point has a connection of physical network of 1 of 4 Dell 6248 switches which are currently in a single stack managed as follows.

  AP 1-> Port of the Switch 1 40

  AP 2-> Port of the Switch 2 36

  AP 3-> Port of the Switch 3 17

  The managed pile and AP are currently using the 192.168.1.0/24 on VLAN 1 - default and I created a VLAN 10 - guest.

  The APs have two SSID WLAN, 'corporate', which is also on the 192.168.1.0/24 range and 'guest' that is located on 192.168.99.0/24. I put the "guest" to mark its traffic with VLAN 10 and no DHCP is defined.

  I put the 3 above general Mode ports, allowing all managers and VLAN - 1 that are not marked and VLAN - 10 they are labeled.

  I also put a Zyxell router with a static address of 192.168.99.254 in Switch 4 Port 24 and set the access mode for VLAN 10.

  The router is configured to provide DHCP for the beach of 192.168.99.0/24.

  Now when I connect a laptop to our 'coporate' WLAN, everything works fine. I get a DHCP address from our server and I can reach everything as usual.

  When I connect to the "guest" WLAN, I do not receive a DHCP address, in addition, I am able to ping on subnet 1 hardware VLAN I thought would not be possible.

  Can someone take a look at this config and I would like to know what is the problem with him?

  ! Current configuration:
  ! Description of the system «PowerConnect 6248P, 3.3.12.1, VxWorks 6.5»
  ! 3.3.12.1 system software version
  ! Passage mode is configured as disabled
  !
  Configure
  database of VLAN
  VLAN 10
  VLAN 10 1 routing
  subnet of VLAN association 192.168.99.0 255.255.255.0 10
  output
  unicast SNTP client enable
  192.168.1.18 SNTP server
  battery
  1 5 Member
  2 5 Member
  3-5 Member
  4-5 Member
  output
  switch priority 1 12
  IP 192.168.1.212 255.255.255.0
  default IP gateway - 192.168.1.227
  IP - my.domain domain name
  name of the IP-server 192.168.1.18
  name of the IP-server 192.168.1.19
  name of the IP-server 192.168.140.2
  IP routing
  IP route 192.168.99.0 255.255.255.0 192.168.99.254
  interface vlan 10
  name of the "Guest".
  Routing
  IP 192.168.99.212 255.255.255.0
  bandwidth 10000
  IP helper-address 192.168.99.254 dhcp
  IP mtu 1500
  output
  level of a8e64cdc85228f4c837da747958ffd74 user name 'admin' password encrypted 15
  l2relay DHCP
  DHCP l2relay vlan 2.10
  !
  interface ethernet 1/g7
  Auto mode channel-group 2
  output
  !
  interface ethernet 1/g8
  Auto mode channel-group 1
  output
  !
  interface ethernet 1/g40
  switchport mode general
  switchport general allowed vlan add 10 tag
  output
  !
  interface ethernet 2/g36
  switchport mode general
  switchport general allowed vlan add 10 tag
  output
  !
  interface ethernet 3/g2
  Auto mode channel-group 2
  output
  !
  interface ethernet 3/g17
  switchport mode general
  switchport general allowed vlan add 10 tag
  output
  !
  interface ethernet 3/g48
  Auto mode channel-group 1
  output
  !
  interface ethernet 4/g24
  switchport access vlan 10
  output
  output

  I was looking back through the configuration, and on the 24 port setting, I see there is a command to access in place, but the port is not set to enter the mode. Can you try to put the port in access mode?

  interface ethernet 4/g24
  switchport mode access

  During the test with the laptop plugged on the switch, we should test it first with a static IP address. This is to ensure that we have a connection established. Then you can move on to DHCP.

  The router will appear in the output of one of these two commands?

  console switch arp #show

  #show bridge console table address

• Very Simple Config on a 6248

  I have the need to have 3 VLAN

  3 VLANs cannot communicate with each other.

  VLAN must be able to access the internet

  My gateway is a standard Linksys router type with the IP address of 192.168.1.1

  My IP switches is 192.168.1.7 (as shown below in config)

  I don't know what to do next...

  TestSwitch #show running-config
  ! Current configuration:
  ! Description of the system «PowerConnect 6248P, 3.3.3.3, VxWorks 6.5»
  ! 3.3.3.3 system software version
  ! Passage mode is configured as disabled
  !
  Configure
  database of VLAN
  VLAN 20,30,40
  VLAN 20 1 routing
  VLAN 30 2 routing
  VLAN routing 40 3
  output
  hostname "TestSwitch".
  battery
  2 5 Member
  output
  192.168.1.7 IP address 255.255.255.0
  Default IP gateway 192.168.1.1
  IP helper-address 192.168.1.1 dhcp
  interface vlan 20
  name "private".

  Routing
  IP 10.11.12.10 255.255.255.0
  output
  interface vlan 30
  name 'Public '.
  Routing
  IP 10.11.13.10 255.255.255.0
  output
  interface vlan 40
  name of the "Training Center"
  Routing
  IP 10.11.11.10 255.255.255.0
  output

  !
  interface ethernet 2/g3
  switchport access vlan 20
  output
  !
  interface ethernet 2/g4
  switchport access vlan 40
  output
  !
  interface ethernet 2/g5
  switchport access vlan 20
  output
  !
  interface ethernet 2/g6
  switchport access vlan 20

  output
  !
  interface ethernet 2/g7
  switchport access vlan 20
  output
  !
  interface ethernet 2/g8
  switchport access vlan 20
  output
  !
  interface ethernet 2/g9
  switchport access vlan 20
  output
  output

  Yes, you have essentially the same scenario. If the fix must be the same. Movement of traffic except VLAN 1 should allow routing to work, VLAN 1 is not routable management unless a VLAN is changed to one VLAN different.

• 6248 VLAN do not receive the DHCP scope

  I created two new DHCP scopes in my windows server 2003:

  192.168.2.0 - public, and
  192.168.3.0 - VOIP.

  This DHCP server is connected to a Dell powerconnect 2708, which is connected to our new powerconnect 6248P via fiber point-to-point.

  In the new computers on network on the default 1 VLAN are correctly attributed IPs as they connect.

  I issued the following commands to the 6248 CLI:

  Enable
  Configure
  database of VLAN
  VLAN 20
  VLAN 30
  output

  Configure
  range of interface ethernet 1/1-g1/g2
  switchport mode general
  VLAN allowed switchport General add 20
  switchport General pvid 20
  l2relay DHCP
  output

  Configure
  range of interface ethernet 1/1-g3/g6
  switchport mode general
  VLAN allowed switchport General add 30
  switchport General pvid 30
  l2relay DHCP
  output

  interface ethernet 1/g11
  switchport mode general
  VLAN allowed switchport General add 20
  VLAN allowed switchport General add 30
  l2relay DHCP
  output

  Configure
  interface vlan 20
  name 'PUBLIC '.
  Routing
  IP 192.168.2.1 255.255.255.0
  IP helper 192.168.1.150
  output

  Configure
  interface vlan 30
  name "VOIP."
  Routing
  address 192.168.3.1 255.255.255
  IP helper 192.168.1.150
  output

  IP routing

  I also added all traffic on VLAN 20 and 30 of VLAN on ports 1/g11 (6248) and port 2 (2708). VLAN 1 access was removed from ports 1/1/g1-g6 (6248)

  Everything seems to have been set correctly, but I can't get a response from the DHCP server on all ports attached to VLAN 20. The powerconnect 2708 switch is unable to pass the baton to the server? Is it possible that something falls in the point to point?

  I would greatly appreciate any comments or suggestions, thanks!

  The 6248 has no default gateway. It wont let me put 192.168.1.1 because he does not reside in the same subnet as the 6248 (192.168.99.1)

  The 2708 has listed 192.168.1.1 as its default gateway.

  At this point, the network has too many complexities for me to unravel. I am very happy that at least I solved for DHCP when we finally migrate our server to the new location.

  Once the server is up, and the gateway/firewall are directly connected to the 6248; I will review the correct configuration of this network.

  Some advice to those who might have a similar problem: check your management VLAN. It may not be the same VLAN 1 if you plan to routing to work from VLAN 1 to nowhere else because the VLAN management cannot be routed. Also check static routing of your access point, make sure the front door has a return of the ips of your VLAN, IE: 192.168.2.0 255.255.255.0 gateway_ip

  That's all for now. Thank you to all who have contributed

• LACP group does not work with stacked 2 DELL PC 6248 and ESXi 2 5.5

  I would like to use LACP/LAG in vSphere 5.5. So I created a new vDS and a group LAG. 2 NICs per host should be used for this. We use 2 hosts, so the total 4 ports are involved. Basically, you can refer to a diagram at vmwares KB article 2051826 (http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=2051826)

  It's only 2 lacp group links are active, then the other 2 are inactive. Active is the only one of the esx hosts, it depends on which ports are going to be active first.

  Any advice? Someone at - it a config like this works?

  Best regards

  Alex

  The config for switch:

  ! Current configuration:
  ! Description of the system «PowerConnect 6248P, 3.3.7.3, VxWorks 6.5»
  ! 3.3.7.3 system software version
  ! Passage mode is configured as disabled
  battery
  1 5 Member
  2 5 Member
  output
  Configure

  interface ethernet 1/g8
  Auto mode channel-group 3
  Description "ESX2_vmnic5".
  Disable spanning tree
  switchport mode general
  switchport General disable filtering of capture
  switchport general allowed vlan add 20 tag
  output

  interface port-channel 3
  Description "ESX".
  hash-mode 6
  Disable spanning tree
  switchport mode general
  switchport General disable filtering of capture
  switchport general allowed vlan add 20 tag
  output

  Thanks to the good support at DELL.

  The secret is that you must create a separate group on the switch for each esx host. On the side of esx, you have the config with group a lacp/gal. But on the side of the switch, you need 2 groups for two guests. VMware should have this more clear I think.

• PowerConnect 6248 stacking using the front SFP Ports

  I am trying to stack two Dell Powerconnect 6248 switches. Currently they are chained together, but I modules fibre for the front sfp ports. Theoretically, I should be able to stack them. But when I try:

  stack 1/g45 #stack - port console (config-battery)

  Could not set the front panel stacking mode.

  Any ideas? Thank you!

  The PCT6200 requires a stack of modules installed in Bay 1 (XG1 XG2) at the rear of the switch. The stacking module uses CX4/Infiniband type stacking spacers.

  Stacking of front port / user is not supported

• ISP / IP Public routing with 6248P PowerConnect switch

  My ISP says I need to pass a level 3; I have a couple of Dell 6248P

  I get a single IP address in the range of 216.2.69.x/30 and a default gateway.

  I have ALSO (usable) 5 of the intellectual property in the 216.2.234.X/29 range.  I have 3 with separate public web servers IP, I need to host on the Internet (they are protected by a firewall/DMZ had through Microsoft TMG).

  My ISP waiting to route my public IP 'par' 216.2.69.X gateway.  Not only change the IP used 5, I have to send it.

  Can I do this with a single Dell 6248P?

  Tagging VLAN would not "work, I don't think that, as who knows if everything that we too are surfing, or whatever the customer is looking at our public IP, the web site would support tagging vlan.

  I can do a 'physical segmentation"on 4 ports say then the installation program a route from

  216.2.69.1-online 216.2.234.64, 65, 66?

  and

  216.2.234.64, 65, 66? -Online 216.2.69.1.

  with 6248 routing?

  If the Dell PowerConnect 6248 this is not possible, can anyone recommend a router that can?

  Thank you

  == John ==

  I make a few assumptions here, so if I'm wrong, please correct me.  Here's how you must configure the 6248 and this is just one example.  The ports you are using may be completely different.  Just make necessary substitutions and you should be fine:

  Create a VLAN 10 and VLAN 20

  Enable

  config

  database of VLAN

  VLAN 10.20

  output

  Assign an IP address in VLAN 10

  interface vlan 10

  216.2.69.1/30 IP address

  output

  Assign an IP address in VLAN 20

  interface vlan 20

  216.2.234.65/29 IP address

  output

  enable routing in the world

  IP routing

  Go to an interface to which you connect to the ISP and set access mode for VLAN 10

  interface ethernet 1/g1

  switchport mode access

  switchport access vlan 10

  Disable spanning tree

  output

  Go to the interface or interfaces that you will use for your servers.  If you connect the servers directly to the 6248 you do the following:

  range of interface ethernet 1/g2-1/g4

  switchport mode access

  switchport access vlan 20

  disable the spanning tree (but only if you're connected directly to the server)

  output

  Configure a default route to get the ISP since public addresses internal

  IP route 0.0.0.0 0.0.0.0 216.2.69.2

  If your ISP est.69.1 and you etes.69.2, your last noted the route should point vers.69.1 instead de.2.

  I hope this makes sense.

• PowerConnect 2824 Ports SFP does not

  We bought a new switch 2824 with a corresponding to SFP module replace old 2724 PowerConnect and SFP module.

  After the configuration of the switch and installing it, we were able to get a connection on our uplinked to fiber.
  SFP light illuminates and flashes from time to time, and the switch detects correctly module SFP is inserted and that the fiber is connected.  We can see the insertion of the SFP is detected and the switch for change of fiber mode by looking at the output of the console, and the web administration port status page lists the port as "ComboF" when the SFP is inserted and the fiber is connected.

  However, the switch always indicates that the port State is down.  (The port is not administratively disabled.)

  The old switch works very well with the old SFP module.  The new switch does not work with the old or the new module SFP.  We tried two combo SFP ports.  We also checked that the fiber itself is fine. We cannot get the new switch to display the drop-down list port status that up when you use the SFP. We tried to completely reset the new switch by removing the configuration file via the boot over the serial connection menu and re-run the initial configuration wizard, but the port still won't go up.

  Any ideas?

  After a few tests yesterday, we determined that part of auto-negotiation must be disabled for switch work with our copper and fiber Media converters.

  The 2724 works very well with our media converters, with auto-negotiation enabled.

  The 2824 works very well with auto-negotiation enabled when it is connected to an another SFP transceiver in building switch.

  But when we introduce the Media Converter in the path, the 2824 will bring only the link up if you disable auto-negotiation.

  So far, everything looks good.

• PowerConnect 6224: Dell SFP + port supports combine Dell SFP?

  I have a Dell Powerconnect 6224 switch and I installed a Dual Port SFP + Module of adaptation for PowerConnect
  6200 series at bay2 at the rear of the switch. I inserted a transceiver, SFP 1000BASE-LX, wavelength 1310nm 10km Reach in the SFP slot + and the other end is connected to a connector SFP 1gbe. I don't have any link. My question is if Dell SFP ports + supports SFP transceivers or it only supports SFP transceivers +?

  I checked the ports to help an SFP + SFP +, 10GbE, copper Direct Attach cable Twinaxial, and link LEDs are lighting up.

  I believe that the SFP ports + back work with SFP transceivers. Ports before combo will work with SFP transceivers. Another thing to look at is the cable being used. Don't forget that there are specifications that are compatible with transceivers FPS are you wanting to use. A SFP + SFP connection would require that the SFP transceiver + supports a connection of 1 GB.

  Hope this info helps.

• PowerConnect 5324 SFP Module

  Hello

  I have a PowerConnect 5324 and a "QLE2462 PCI Express 4 Gb FC Dual Channel".
  What modules I need to buy to make them talk to each other?

  The seats of switch on the server, so I'm sure I need a SX module.

  I have no knowledge on the FC so a deep answer really appreciated

  This will be my homelab so nothing of quality required

  Kind regards
  Andrzej

  Hello

  The switch supports modules 1000-SX and 1000-LX. Those aren't Fiber Ethernet, fiber channel storage. The 5324 does not support the Fibre Channel.

• Connection EQL 6110 X (10G SFP +) PowerConnect 6224 10 Uplink ports

  Dear friends,

  Need your help...

  Please let me know if I can connect EQL 6110 X (10 G SFP +) storage to ports 10 G SFP + PC 6224 for iSCSI to my servers on a local network connectivity that is 1 G.

  Correct, do not use the uplink ports for Gigabit Ethernet switch for 10GbE tables.    It can connect, but performance and stability will most likely suffer.   So has been the experience of other customers who have tried to do.

• SFP transceiver compatibility

  I'm about to take my PC3524 a PC6248. Is the SFP transceiver in my 3524 compatible with the 6248? Or I have to get the new transceiver also?

  Thank you

  This transmitter/receiver is compatible with both switches and will work fine.

  See you soon

• Compatibility SFP

  Hello

  I currently have several Cisco C2960X-24TD-L. I would like to read, it is possible to connect two SFP GLC-SX-MMD and GLC-LH-SMD with a multimode cable.
  When the switch is connected to the GLC-LH-SMD lights but the GLC-SX-MMD does not illuminate. He will issue an order?

  Kind regards

   I would savois it is possible to interconnect two SFP GLC-SX-MMD and GLC-LH-SMD with a multimode cable.

  Is not possible.  The two modules (and associated cables) must be of the same wavelength.  It is GLC-SX-MMD-to-GLC-SX-MMD (with multi-mode cable) or GLC-LH-SMD-to-GLC-LH-SMD (with single-mode cable).

• Modulo 10G sfp + by powerconnect 7048

  Salve,

  Sono alla ricerca del modulo di expansion in oggetto by uno pass di UN nostro client che ha G7SYZY1 st

  da schede tecniche should be part n. J3PC9

  You can help?

  Grazie

  Buongiorno,

  by kit accessori invito a cars o acquistare he OUA commercial di Re, questo forum enjoy being a silver is.

  Saluti

  Marco