SFP transceiver compatibility

Similar Questions

• Can I change the speed on a GB SFP?

  We have an ASR1002 edge router I need to connect a 100 LH SM Fiber (1310). I have a GLC-LH-SM and a SFP SFP-GE-L. I need to set the speed to the ASR for the interface of the FPS to 100/full. The IOS does not "speed" controls at the interface level. Can I set the speed to 100 for one of them and, if so, how?

  Cannot change the speed for SFP module.

  However, for the 100 M SFP Transceiver compatibility Document (link below), the ASR1002 supports the module of GLC-GE-100FX of 100 MB interconnects (split into a compatible slot in GE).

  http://www.Cisco.com/en/us/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL632702.html

  Good luck!

• PowerConnect 2824 Ports SFP does not

  We bought a new switch 2824 with a corresponding to SFP module replace old 2724 PowerConnect and SFP module.

  After the configuration of the switch and installing it, we were able to get a connection on our uplinked to fiber.
  SFP light illuminates and flashes from time to time, and the switch detects correctly module SFP is inserted and that the fiber is connected.  We can see the insertion of the SFP is detected and the switch for change of fiber mode by looking at the output of the console, and the web administration port status page lists the port as "ComboF" when the SFP is inserted and the fiber is connected.

  However, the switch always indicates that the port State is down.  (The port is not administratively disabled.)

  The old switch works very well with the old SFP module.  The new switch does not work with the old or the new module SFP.  We tried two combo SFP ports.  We also checked that the fiber itself is fine. We cannot get the new switch to display the drop-down list port status that up when you use the SFP. We tried to completely reset the new switch by removing the configuration file via the boot over the serial connection menu and re-run the initial configuration wizard, but the port still won't go up.

  Any ideas?

  After a few tests yesterday, we determined that part of auto-negotiation must be disabled for switch work with our copper and fiber Media converters.

  The 2724 works very well with our media converters, with auto-negotiation enabled.

  The 2824 works very well with auto-negotiation enabled when it is connected to an another SFP transceiver in building switch.

  But when we introduce the Media Converter in the path, the 2824 will bring only the link up if you disable auto-negotiation.

  So far, everything looks good.

• PowerConnect 6224: Dell SFP + port supports combine Dell SFP?

  I have a Dell Powerconnect 6224 switch and I installed a Dual Port SFP + Module of adaptation for PowerConnect
  6200 series at bay2 at the rear of the switch. I inserted a transceiver, SFP 1000BASE-LX, wavelength 1310nm 10km Reach in the SFP slot + and the other end is connected to a connector SFP 1gbe. I don't have any link. My question is if Dell SFP ports + supports SFP transceivers or it only supports SFP transceivers +?

  I checked the ports to help an SFP + SFP +, 10GbE, copper Direct Attach cable Twinaxial, and link LEDs are lighting up.

  I believe that the SFP ports + back work with SFP transceivers. Ports before combo will work with SFP transceivers. Another thing to look at is the cable being used. Don't forget that there are specifications that are compatible with transceivers FPS are you wanting to use. A SFP + SFP connection would require that the SFP transceiver + supports a connection of 1 GB.

  Hope this info helps.

• 10GbE SFP + LR transmitters for Broadcom 57800 S

  Hi all.

  I have a r.620 with a card Broadcom NetXtreme 58700 S daughter 2x10GbE SFP + slots.

  Dell has only SR (short-range 850nm) issuers listed on their homepage, but need us a 10GbE SFP + Transceiver for the LR 1310nm wavelength. Is there a recommended ARVA LR or can I use any module SFP + support 1310nm?

  Thanks in advance

  The two I know are:

  Dell Reference number: N198M, Finisar - FTLX1371D3BCL-DL

  Dell Reference number: 5DCPW, Avago - AFBR-707SGDZ-D1

  I don't know there are several other transceivers with the same characteristics that will work.

• Determine the side "reception" of the SFP optics

  Hello.

  I have an upcoming implementation of dark fibre which requires me to run ZX SFP (cable distance of more than 10 k), but I need an attenuator in the side reception of the FPS at each end.

  How I think we're the receiver?

  With SFP 1350nm, it is not 'light' to see the exit and the number which is the transmitter, as it is on 850nm SFP - so, how do I do to the longer wavelength, those?

  I've been unable to find a representation of the disgrametic of a CWDM SFP that indicates a specific - is it reasonable to assume a SFP WDM standard, is not the same thing?

  Or should I connect with the attenuator on the one hand, check the input power, and then plug it into the other side and see if it makes a diference?

  Thank you.

  Look at Figure 1.

  Cisco SFP and SFP + Transceiver Module Installation Notes

• Cisco SFP module name

  What is the difference between the module two next?

  SFP-GE-L = vs SFP - GE - L, we have = to sigh at the end and others are not.

  http://www.Cisco.com/c/en/us/products/collateral/interfaces-modules/Tran...

  SFP-GE-L	1000BASE-LX/LH SFP (DOM)	GLC-LH-SMD	1000Base-LX/LH SFP transceiver module, MMF/SMF, 1310nm, DOM	-
  SFP-GE-L =	1000BASE-LX/LH SFP (DOM)	GLC-LH-SMD =	1000Base-LX/LH SFP transceiver module, MMF/SMF, 1310nm, DOM	-
  SFP-GE-S	SFP 1000BASE-SX (DOM)	GLC-SX-MMD	1000BASE-SX SFP transceiver module, MMF, 850nm, DOM	-
  SFP-GE-S =	SFP 1000BASE-SX (DOM)	GLC-SX-MMD =	1000BASE-SX SFP transceiver module, MMF, 850nm, DOM	-

  For all Cisco SKU (Stock keeping units), the '=' at the end means a piece of spare or ordered separately article.

  Without a '=' means usually the exact same item is ordered in a parent configuration - for example, a SFP as an optional part of a module switching.

  They are exactly the same physical part.

• can you connect the SFP - 10 G - SR low-support to SFP 1000BASE-SX?

  Hello world:

  today I use the SFP + 'SFP - 10 G - SR' in Cisco Catalyst 2960 S-48TD-L connect to the SFP 1000BASE-SX to 6509 WS - X 6724-SFP module.

  the port setting is master, but they do not work, even the light don't flush. Then, I also use the SFP 1000BASE-SX to replace SFP + SFP - 10 G - SR in

  2960 S-48TD-L, then they cany working.

  I look to the top of the cisco data sheet, there is no roadmap to satament database 10G sfp + can't low support 1 G sfp. So, I want to confirm the problem.

  Otherwise, the 10 FPS + can only use for 10G SFP +; can't go down the suport 1 G SFP.

  This means: If you want to use the 10 G SFP + the other old device also need to replace.

  Thank you ~ for your help!

  Hi Marvin,.

  I found this conversation today, because I'm looking for an answer on a question similar to the question that Jerry asked, at the opening of this discussion.

  So my problem is this. In a certain place, I need two 10 GB and a connection of 1 GB on an optical cable. To cut costs, I tried with WS-C2960X-48FPD-L, but because it contains only two ports of SFP +, I tried with two WS-C2960X-24PD-L which will be connected with the battery modules.

  Then, having two WS-C2960X-24PD-L, I have 2 x 2 ports SFP + 1 GB. There are two open questions:

  1. can I put 1 GB transmitter SFP module SFP + port (that I have a connection of 1 GB at remote site)?

  2. can I use two switches to 24 ports mentioned 2960, in a way that I use one of them for the two connections of 10 GB (using ports SFP + 10 GB connection) and the second member of the battery so that we (2 available) port SFP + is used to 1 GB SFP connection (using the SFP port + as mentioned in question 1)?

  I'm not sure if your previous statement covers my questions, because it is not clear if the 1 GB SFP transceiver can be inserted in the port SFP + WS - C2960X - 24PD - L (or any other a port SFP switch +).

• Optical transmitter/receiver

  Hello

  I have catalyst express 500 switch with GLC-SX-MM, 1000BASE-SX SFP transceiver modules.

  Is it possible to change the speed of the transceivers to 100Mbit

  I need know, because on the other side of the link is a converter of transmissions/metallic (AT-MC101XL

  Card Fast Ethernet 100BASE-TX, 100BASE-FX (ST) multimode fiber (2 km), stand-alone media converter)

  In my view, converter and tranciever are not compatible. Is it not?

  I thank.

  Unfortunately, the GLC-SX-MM is not switchable on operation of 100 MB. You can buy a 100Base-FX SFP module for your switch.

  According to the following document, these are compatible with the 500 Express interfaces of 100 MB:

  GLC-GE-100FX

  GLC-FE-100FX

  GLC - FE - 100LX

  GLC-FE-100BX-D

  GLC-FE-100BX-U

  This document details the interoperability and the specifications of these SFP modules:

  Cisco Small Form - Factor Pluggable (SFP) transceiver Modules Maintenance and troubleshooting

  http://www.Cisco.com/en/us/products/HW/modules/ps4999/products_tech_note09186a00807a30d6.shtml#model>

  I hope this helps!

• 10GE copper Nexus 5 k

  Hi all.

  Small question: what FPS do we need on our Cisco Nexus 5 k to connect to a server to 10 Gigabit Ethernet, if this is going to be connected with a CAT7/RJ-45 UTP cable?

  We have several SFP modules that work with fiber on our Nexus N5K C5596UP, but we have never signed anything with copper, and still less that supports 10G. Someone told us that it has been supported, but check the Cisco documentation we only see cables twinax, nothing else.

  I appreciate all help.

  Thank you.

  Hello

  I don't think that a SFP transceiver-10GBASE-T is available for the Nexus 5 K.

  If you look at the Modules Cisco 10GBASE SFP data sheet , there is no such SFP + transceiver listed.

  A search on OCC for 10GBASE-T transceivers finds only the transmitter/receiver X 2 - 10 GB - T listed in the Cisco 10GBASE X 2 Modules data sheet which is of no use to you.

  There is a plug-in 12-port 10GBASE-T (PID-N55-M12T), which is perhaps overkill for your needs, but also who took in charge only in the Nexus 5596 T chassis according to the Cisco Nexus 5548 P, 5548UP, 5596UP and 5596 T switches data sheet. I don't know why this would be the case given the 596UP and 5596 T are based on the same ASIC, etc.. Perhaps a question to your Cisco sales representative.

  Concerning

• Compatibility of Microsoft® 2.4 GHz Transceiver v8.0

  Microsoft® 2.4 GHz Transceiver v8.0 works with keyboards and mice?

  Those. what it delivered.  Various combinations of frequencies and codes are used to prevent bleedover in office environments where any number of people will have the same or similar receiver.  Otherwise, your computer would meet several mouse and keyboard and your mouse and your keyboard would cause other computers respond.

• PowerConnect 6248P 10 G SFP + compatibility

  Hello

  Is could someone please tell me if this device is compatible with 6248Ps after adding a module of 10 G uplink for the back?

  Thanks in advance

  Peter

  Yes, this transceiver will work perfectly in your P. 6248

• Compatibility SFP

  Hello

  I currently have several Cisco C2960X-24TD-L. I would like to read, it is possible to connect two SFP GLC-SX-MMD and GLC-LH-SMD with a multimode cable.
  When the switch is connected to the GLC-LH-SMD lights but the GLC-SX-MMD does not illuminate. He will issue an order?

  Kind regards

   I would savois it is possible to interconnect two SFP GLC-SX-MMD and GLC-LH-SMD with a multimode cable.

  Is not possible.  The two modules (and associated cables) must be of the same wavelength.  It is GLC-SX-MMD-to-GLC-SX-MMD (with multi-mode cable) or GLC-LH-SMD-to-GLC-LH-SMD (with single-mode cable).

• Gigabit Ethernet SX Mini-GBIC SFP Cisco transceiver

  This reference Cisco: Cisco MGBSX1

  Any type of connector can support?

  And how can I change the type of connector of LC to SC?

  Ho Yousovich, all GBIC SB is LC.

  http://www.Cisco.com/c/en/us/support/docs/interfaces-modules/CWDM-GBIC-s...

• Cisco WS-C3750X-12 s - S SFP modules

  Dear team

  I required 12 new sfp port switch I chose WS-C3750X-s-12s
  for my requrement is here my question is...

  Is I need to add separate trancievers SFP for this switch or not?

  Care technical I have not found that rock come alongwith 12 trancievers then how can I configure this procudt

  Hello

  The X Catalyst 3750 - 12s switch is a based FPS you don't need SFP transceivers. Take a look at table 6 to the Cisco Gigabit Ethernet transceiver Modules compatibility matrix for details on the supported transceivers and the OS release that they are taken care of.

  Concerning