PREL11 - lost contact with my media - said "media offline".

Similar Questions

• I put my cRIO 'DHCP' to 'local connection' and lost contact with her.

  I put my cRIO 'DHCP' to 'local connection' and lost contact with her.

  I changed the location setting labelled '2' to post a link-local only, so I think I hit save to '3 '.  So, I have had no contact with my cRIO network.

  I tried;

  Hit the reset button

  A MAX of opening closure

  Go to safe mode

  Lift the switch to reset IP

  Power cycling the cRIO

  Directly from the host to my target of cat 5 cable running

  None of it worked, and I have no contact with my cRIO.

  

  This is what MAX looks like now.  How can I fix?

  

  It turns out that I had more of a problem.  Corrupt drivers, 255 in many in my subnet mask, overly complex LAN, use server control... you get the idea.  So I just deleted all software, disassembled everything and more from scratch.  Now back to the top and work.

  Thanks for the tips everyone, all the pieces and peace where it is useful to help me see the bigger picture.

• Lost sound with PC Media Center HP

  My office is a HP Media Center m1050y (PJ697AV-ABA) CTO of desktop PC. It runs Windows XP. I have a card Creative SB Audigy 2 ZS Audio sound [E480]. The sound is set by default to this card.

  One day, I listen and watch a video stream on the Internet and the next day I had no sound. I booted up and I don't think I had sound at first, and then I removed my advertising program. I went to point restaurant the day before but that does not restore the sound.

  I reinstalled the drivers and looked at the BIOS splash screen and have tried automatic, enabled and disabled.

  I worked through the support HP on the list page:

  http://support.HP.com/us-en/document/bph07154

  Still no sound. The connections are good.

  I tried to run the diagnostics of creative media for the hardware and the software again. Previously, it would be error. It was a mistake but I pushed the and everything happened. I ran it again and everything.

  The speaker system is supplied with the PC. It's a Klipsch loudspeakers and a subwoofer. I had checked the fuse on the box and it was ok. The computer goes into the right speaker which has a small green light. The resisdes pre - amp with the subwoofer. I know power going to the subwoofer because it was hot, and the fuse is ok. Also the green light was carried out.

  I could hear also some clicks and pops in time outside so it appeared to work.

  Pretext to check hypotheses twice, I pulled an old speaker system and hung. I had sound.

  My guess is that the missed preamplifier that has been powered speakers. Also the green light did not shine. What I saw, that was my office of light reflecting on the little green bulb.

  Thanks for your help.

• How do I restore my apple ID after I lost contact with my original activation id (the one I used to activate the phone (iphone 5 s) initially)

  I have an iPhone 5s which I locked using 'find my iPhone' with the apple ID * gmail.com.

  in order to unlock my iPhone, I need of the apple I used for activation, which I don't remember ID, I removed the lock 'Find my iPhone' in the 26.1

  but when I open my phone yesterday asking apple ID to activate my iPhone...

  p.s

  I have the original with the IMEI label box...

  Help, please

  < images and contact information and Email published by host >

  If you don't remember that Apple ID and password, you just present the original invoice, indicating your name, the name of the dealer, date of sale and the series/IMEI number # etc. to Apple.

• Update codec C20/C40 cisco to 6.1.2 meetings lost contact with cisco

  So I improved a few Cisco C40 codec C20 5.1.6 to 6.1.2 the process was smooth.   He updated the device of the codec and cameras, but once the upgrade has completed, the touch screen of cisco lost all meetings.  Is there a way to put all meetings (from outlook calendars) of cisco press?

  A mixture of CUCM and TMS is not really possible.

  In any case, which concerned the TMS, can you set a password for the admin on the endpoint and then add this

  password under the connection tab in the Navigator system of this endpoint.

  After that do a force refresh and apply management settings and see if the meetings will appear again.

  As TMS pushes this information, it would be the correct symptom do not show this info when

  There is a communication / authentication problem.

• I try to send a book of Lightroom 5.2 to Blurb, but as we have very slow broadband I tried for 9 hours on 5 days, but it cannot send to Blurb.  Whenever he gets more than half way through, then told me he lost contact with the server I

  Someone know how to export a book built in 5.2 Lightroom to another device, like our broadband is so slow I can't send the book to Blurb and wish so to save the book also if I use faster broadband to download?

  Him DianaGamble.

  Simply select 'Export to the book in PDF format' in the book module.

  Then copy it to another device.

  Please see export a photo book > create a Photo book in Adobe Photoshop Lightroom 4 (instructions will be same in Lightroom version 5)

  

  Kind regards

  Assani

• I want to re install with a clean sheet. I have install, but my old catalog loads again. How do I delete catalog and where it is stored. I lost some of the media that came with my drive by accident so I need to re install

  I want to re install with a clean sheet. I have install, but my old catalog loads again. How do I delete catalog and where it is stored. I lost some of the media that came with my drive by accident so I need to re install

  HI ATR

  Just update you 13 windows 7 items... I sat until midnight and found the program data and ended up finding the catalog. I deleted the catalog now. and uninstalled items 13. I hope that when I reinstall it will be like new, and I can go back again. I had messed up I saw when viewing the photos in the media, it was media files and thought they shouldn't be there so I deleted them. Maybe thinking about now I get an error. Before, I made a slideshow with the media from the drive. I just started using elements 13 I used windows live previously for videos. Can you let me know also what photoshop elements or first, you use the most.  Also if I import video files in why do I see them I think of thumbnails. That's where I went wrong and thinking, they shouldn't be here. I brought a few books and trying to go through the learning process. What camera do you use?  Many questions sorry. Thanks for any help.  Russell

• Burn a CD with Windows Media Player

  I tried to burn a cd with windows media player.  I think that it is version 11.   I put the songs I want to burn on the right side where it says to put them.  I use a cd cd - r Phillips.  He'll burn 3 or 4 songs, and then eject the disc.  I tried several times and it does every time.  Any advice on how to burn the entire list of songs.  There are 15 I wanted to put it on disk.  And it's an 80-minute drive, so there is a lot of time on them.  I lost a few disk already so any advice would be appreciated.

  Thank you

  Rita

  you have to 'turn off' the ' auto eject and auto burn / rip "feature for your cd device.

  in this way the cd will stay "unburn" and can accept more files.  later, when you have copied all the files on the cd, then you can manually run a ' burn / rip.

  try to go to the menu bar of media player file.  then, under Tools > options there should be a tab to customize the "rip" where you can change the ejection and extraction methods.

  regarding as to why you seem to only be able to copy multiple files at the same time, it is probably due to low resources on your system.  Maybe you are low on memory or disk space when you use the media player.

  so, you could try to just use the Explorer to transfer files on the cd.

  You can open the Explorer and then find the folder that contains your music / song files.   then as with any file, you can drag and drop them on the cd or use other methods that you want to copy files from one place to the other.

  also, most computer come with specialized software that is designed for your device to computer and cd model.  This software will be has features to copy files to the cd, and will also have the necessary controls to fine-tune the device cd and windows to play and the extraction of files.

  Finally, it has been my experience that about five years of cd home-made, even if you buy the best cd for recording as those made with layers of gold and those with false promises that they last forever...

  Unlike the cd music that we buy at the store, the method that we have with the computer is not industrial strength and something happens to the layers inside the House made conference that degrade over time.  I have studied this issue carefully and I just to let you know about the phenomena.  (I almost lost some one of a kind songs where the group no longer exists or their albums.  I actually have the only copies of these songs in particular in the world)

  in any case, certainly keep copies of your music on the hard disk. You can also store copies of your music on the site of skydrive from microsoft for free.

• I am trying to sync my ipod with my windows media player and when I connect my ipod windows media play is not read. How can I sync my ipod with windows media player?

  I am trying to sync my ipod with my windows media player and when I connect my ipod windows media play is not read. How can I sync my ipod with windows media player?

  Hello

  Your MP3 player should have 2 settings - MSC that should allow the player to be used as a
  external drive and PSG that is the parameter to use to sync with WMP11. Remove the MP3
  and restart the computer. Change the MP3 in MTP mode - it power off and plug it in.

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Windows media player does not automatically open a video file on a Web site but I save it and open the file with Windows media player to play the video or audio recording.

  Windows media player does not automatically open a video file on a Web site but I save it and open the file with Windows media player to play the video or audio recording. I used to be able to play any video or audio file in any site!

  Hello

  Try resetting the default associations for WMP and IE.

  How to set default Associations for a program under Vista
  http://www.Vistax64.com/tutorials/83196-default-programs-program-default-associations.html
  How to associate a file Type of Extension to a program under Vista
  http://www.Vistax64.com/tutorials/69758-default-programs.html

  If necessary:

  How Unassociate a Type of Extension file in Vista - and a utility to help
  http://www.Vistax64.com/tutorials/91920-unassociate-file-extention-type.html
  Restore the Type Associations by default Vista file extensions
  http://www.Vistax64.com/tutorials/233243-default-file-type-associations-restore.html
  How to view and change an Extension of filename on Vista
  http://www.Vistax64.com/tutorials/103171-file-name-extension.html

  ====================================

  Also follow these steps:

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ------------------------------------------------------------

  Then, if necessary:

  Have you recently installed another player?

  Reset your associations for WMP and IE.

  How to set default Associations for a program under Vista
  http://www.Vistax64.com/tutorials/83196-default-programs-program-default-associations.html
  How to associate a file Type of Extension to a program under Vista
  http://www.Vistax64.com/tutorials/69758-default-programs.html

  ---------------------------------------------

  Do this to reregister the Jscript.dll and Vbscript.dll files.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  type or copy and paste-> regsvr32 jscript.dll
  Press enter

  type or copy and paste-> regsvr32 vbscript.dll
  Press enter

  Restart and if all goes well, it will run now.

  --------------------------------------------------------------

  Have you recently added stores or ANY application from Stardock?

  Using 64-bit Vista?

  Can you think of recent things you did in WMP which could be the cause? You added another
  reader recently or an add-on for WMP?

  When I try to use Windows Media Player 11, the program does not start, or some UI elements
  are empty - a Mr Fixit
  http://support.Microsoft.com/kb/925704/en-us

  Maybe something here
  http://msmvps.com/blogs/chrisl/articles/17315.aspx
  and here
  http://msmvps.com/blogs/chrisl/Archive/2004/10/30/17399.aspx

  Check here the news of WMP11
  http://zachd.com/PSS/PSS.html

  I hope this helps.

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Burning CDs with Windows Media Player in Windows 7. "Error: connect a burner and restart the player.

  Original title: CD burning with Windows Media Player in Windows 7

  When I try to burn an audio CD with Windows Media Player, I get the message "connect a burner and restart the player.

  I am able to burn audio CDs using ITunes, so I don't think that my CD/DVD burner is defective.

  Thanks for your help.  The "fix it" has not worked, but I checked the settings of my Nero 8, Nero Toolkit, Nero Burn Rights program, and he was the one who said "everyone has burn rights" or "nobody burn rights.  When I changed the option to "everyone", everything started to work properly.

• Lost audio on Windows Media Player-Windows 7 - after using the importer of music Amazon

  I lost the audio for Windows Media Player after that download music Amazon importer to import music from I tunes to my new Kindle fire. I realized this after you use Windows Live Media Player to do a 'film' and then save and send an e-mail (the file is compressed and will open with Windows Media Player). The recipient, however, can hear the sound.  Any ideas?
  L

  Problem has been solved-am embarrassed to say that the sound was low. Very embarrassed to say I didn't know that the sound on my computer is not the same as the definition of the sound of the media player.

  L

• Not possible to burn music with Windows Media Player

  When I drag music from MP3 Rocket files to burn the pane in windows media player, they will not 'stick' nor will they stick to the music library... althoguh I did it before in the two front wings, why not more?

  OT: drag & drop

  Hello

  I suggest you try the steps from the following link to burn CD/DVD with Windows Media Player.

  Burn a CD or DVD in Windows Media Player
  http://Windows.Microsoft.com/en-us/Windows7/burn-a-CD-or-DVD-in-Windows-Media-Player

  Additional information:
  Burn a CD or DVD in Windows Media Player: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/burn-a-CD-or-DVD-in-Windows-Media-Player-frequently-asked-questions

  If the problem is only with MP3 rocket software, then I suggest you to contact the support of the rocket.

• Computer crashes when exporting with Adobe Media Encoder

  Hi, whenever I start to export via media Encoder, my computer kind of freezes... I am not able to change or even to use no matter what other applictions when exporting with Adobe media encoder. It didn't happen with the old version CC7. All advice please? Very frustrating.

  Hi Henen,

  Hi, whenever I start to export via media Encoder, my computer kind of freezes... I am not able to change or even to use no matter what other applictions when exporting with Adobe media encoder. It didn't happen with the old version CC7. All advice please? Very frustrating.

  Press SHIFT when you start the program. If this does not work, please contact support at this link: http://bit.ly/PPro-support

  Thank you

  Kevin

• Satellite A105-S2101 - can't watch DVDs with Express Media Player

  I have this laptop Satellite A105-S2101, and the LCD breathed on me in two years.

  Fortunately, I can still use the VGA and S-video output but it may as well be a desktop PC now. Anyway, I just wanted to add that because of this problem, no longer is I can watch DVDs with Express Media Player because it will not accept VGA or S-video as default is just my broken - up, good for nothing always blurry LCD anyway.
  It's only when I'm in Windows mode can I switch to an external monitor.

  The reason I'm writing is, if it is necessary to add anything to an EMP update - this is the time and it would be something to add. What the devil?

  Have you tried another player?
  I prefer the VLC media player. He plays the most video and audio files, it s freeware and easy to use. Check it!

  Have you changed something on your hardware or software configuration before this happened?
  Maybe it's time to reinstall the drive Media Express