Problem of site 2 site config dynamic to static

I must be missing something in the config, but I'm not sure.

Try to get a 506th PIX (6.3) at an ASA 5505 (7.2). The PIX is dynamic IP and the SAA is the static IP address. This is a second Site 2 site VPN between the PIX and PIX, another who has an IP staitic.

I tried everything I can think of. I think it's on the side of the ASA, but not sure. I have reset the pre shared key several times. I tried the sysopt connection permit-vpn on the SAA. He took command, but it does not appear in the config of runn. Put in ipsec-ra tunnels both ipsec-l2l as well as other things. In any case, I have attached my config.

Almost forgot, I used this link as a guide. http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805733df.shtml

Thanks for your help - Keith

Keith,

I think you should compare your ASA to static IP and the PIX for dynamic-IP configs - see what is different (apart from the names of things)

The pre-shared key, I used was test1234 at both ends.

Tags: Cisco Security

Similar Questions

VPN site-to-site between 3 dynamic ip site to ip address static site

Hi all

I have a scenario,

I have a static ip address in the headquarters and I have 4 office locations of all offices of construction site have dynamic ip.

I created a site to site vpn between HO perfect work for 1 site office

but I create a second profile in HO ASA for site office 2 config, I have created does not work.

I use HO ASA 5520 and branches 5505 all site offices is ADSL connection

I enclose my config HO

Can u sat down just how dynamic config several profile in the HO

Thank you

Zeus

It's just a suggestion...

You want to get 3 dynamic sites connected with the HO, right?

HO:

As the branch have dynamic ip, you must use the DefaultL2LGroup profile (the same shared key for all three BO).

The crypto-plan should be dynamic with the right soure/destination NET configured. Exempt NAT with the same source/destination NET as well.

BO:

Configured as a VPN Site-2-Site normal with the HO. The IPSEC Wizard is very useful.

To connect to HO Bo, the branch must initiate the tunnel. After that, you have 2 full functional site site VPN.

http://www.Cisco.com/en/us/partner/products/ps6120/products_configuration_example09186a00805733df.shtml

Welcome,

Norbert

VPN site-to-site dynamic-to-static

Dear

I have a few sites already connected with ASA 5505 VPN site to site with both ending static IP address. Normally, all traffic can be found without any problems. Even, I used 'inside access management' for the two ASA.

Now I have a new office with only the ADSL pppoe. I used to install between Site B:remote the site dynamic IP and IP SiteA:static with a similar example of this easy VPN: http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00805733df.shtml

All my ASA 5505 run 1 8.4 (4)

Site A - Static IP

Site B - Dynamic IP with pppoe connection.

After EasyVPN connected, I don't know how I remote manangment of the site a lan at the ASA 5505 B site?

Best regards

Alan.

If you're ok with or the other solution, it is probably easier to use dynamic to static lan-to-lan, so, at least, that your solution is consistent and fair use lan-to-lan tunnel instead of customer vpn solution mixture and lan-to-lan.

Dynamic to static L2L IPSec VPN

Hello

I've implemented a dynamic to static IPSec Site to Site VPN between a branch (ship) ASA5505 and headquarters. Now, this solution does not allow HQ initiate the IPsec connection.

There is a router behind the ASA5505. I heard that if I want to keep the tunnel upward, so that the HQ customers can switch the traffic to remote clients through the tunnel, I would need to run ALS IP icmp probes on the router behind the ASA.

Could someone explain how to implement it?

Thanks for your help.

Frank

The ICMP probe can be done through any device that is able to do ping, not only of the router.

The reason is that it is interesting traffic triggers the traffic is encrypted by the vpn tunnel, tunnel will stay up, so you will be able to open the connection to the AC to your remote site.

Hope that helps.

Dynamic to static IPSec with certificate-based authentication

I'm trying to implement a dynamic to static LAN2LAN vpn from an ASA 5505 (with a dynamic IP address) to an ASA5520 (with a static IP address)
I wish I had a small (/ 30) network on the side dynamics which I can connect to a larger (/ 24) network on the static side.
I also try to use the identity for authentication certificates.

I produced a root and intermediate CA signed of the intermediate CA with the certificate authority root and then created identity cases for
the ASAs, signed with the intermediate CA using OpenSSL and imported to a trustpoint

I tried to use the instructions on:
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080930f21.shtml
to configure certificates (replacing MS with OpenSSL) and following the instructions to:

I tried the ASDM to set up the cert to identity appropriate on the external interface
[Configuration-> Device Management-> advanced-> SSL settings]

and establish a connection profile [Configuration-> Device Management-> connection profiles] on both devices,
setting the part that gets its IP via DHCP static and the side that has the IP permanently to accept dynamic.

I apply the settings, and nothing happens.

See the crypto isakmp just returns "there is none its isakmp.

I don't know where to start debugging it. How can I force the side DHCP to initiate a connection?

We are sure that both peers are using the same isakmp settings? It seems the policy that uses rsa - sig on one end uses a different Diffie-Hellman group.

KeepAlive to restore a dynamic to static tunnel?

Hi all

I have a dynamic to static 501 501 configuration of operating system 6.3 pix pix. I would use KeepAlive to re - establish the tunnel where the tunnel down. Is this possible?

Theres a workaround for any solution, you have the pix to the extreme end use a local ntp or server syslog, this traffic would bring the tunnel upward, as it has been defined as interesting.

Problem on site to site and between router vpn client series 2,800

Hello

I need a little help.

I have 2 office of connection with a site to site vpn

Each site has a dry - k9 router 800 series.

Each router has actually client ipsec vpn active and all users can connect by using the client vpn with no problems.

I added the lines for the vpn site to another, but the tunnel is still down.

Here the sh run and sh encryption session 2 routers:

OFFICE A

version 15.3
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
OFFICE-A-DG host name
!
boot-start-marker
boot-end-marker
!
AQM-registry-fnf
!
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login xauthlist local
AAA authorization exec default local
AAA authorization exec vty group xauthlocal
AAA authorization exec defaultlocal group bdbusers
AAA authorization groupauthor LAN
!
!
!
!
!
AAA - the id of the joint session
!
Crypto pki trustpoint TP-self-signed-220561722
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 220561722
revocation checking no
rsakeypair TP-self-signed-220561722
!
!
TP-self-signed-220561722 crypto pki certificate chain
certificate self-signed 01

quit smoking
!
!
!
!

!
!
dhcp WIRED IP pool
Network 10.0.0.0 255.255.255.0
router by default - 10.0.0.254
Server DNS 10.0.0.100
!
!
!
8.8.8.8 IP name-server
no ip cef
No ipv6 cef
!
!
!
!
!
Authenticated MultiLink bundle-name Panel
!
!
!
!
!
!
!

!
!
!
!
!
VDSL controller 0
!
property intellectual ssh rsa ssh key pair name
property intellectual ssh version 2
property intellectual ssh pubkey-string

!
!
crypto ISAKMP policy 3
BA 3des
preshared authentication
Group 2
!
crypto ISAKMP policy 20
md5 hash
preshared authentication
OFFICE-B-IP address ISAKMP crypto key XXXXX
!
ISAKMP crypto client configuration group remoteusers
key XXXX
DNS 10.0.0.100
WINS 10.0.0.100
domain.ofc field
pool ippool
ACL 101
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
tunnel mode
Crypto ipsec transform-set esp - esp-md5-hmac xauathtransform
tunnel mode
!
!
!
Crypto-map dynamic dynmap 10
Set transform-set RIGHT
Crypto-map dynamic dynmap 20
Set transform-set RIGHT
!
!
map clientmap client to authenticate crypto list userathen
card crypto clientmap isakmp authorization list groupauthor
client configuration address map clientmap crypto answer
10 ipsec-isakmp crypto map clientmap Dynamics dynmap
20 ipsec-isakmp crypto map clientmap
defined OFFICE-B-IP peer
Set transform-set RIGHT
match address 115
!
!
!
!
!
!
!
ATM0 interface
no ip address
No atm ilmi-keepalive
PVC 8/35
aal5mux encapsulation ppp Dialer
Dialer pool-member 1
!
!
interface Ethernet0
no ip address
Shutdown
!
interface FastEthernet0
INTERNAL description
switchport access vlan 10
no ip address
!
interface FastEthernet1
no ip address
Shutdown
!
interface FastEthernet2
switchport access vlan 10
no ip address
!
interface FastEthernet3
switchport access vlan 10
no ip address
!
interface Vlan1
no ip address
Shutdown
!
interface Vlan10
IP 10.0.0.254 255.255.255.0
IP nat inside
IP virtual-reassembly in
!
interface Dialer0
the negotiated IP address
NAT outside IP
IP virtual-reassembly in
encapsulation ppp
Dialer pool 1
Authentication callin PPP chap Protocol
PPP pap sent-name of user password xxx xxx 0
clientmap card crypto
!
router RIP
version 2
10.0.0.0 network
network 192.168.1.0
!
IP local pool ippool 10.16.20.1 10.16.20.200
IP forward-Protocol ND
no ip address of the http server
no ip http secure server
!
!
the IP nat inside source 1 interface Dialer0 overload list
overload of IP nat inside source list 101 interface Dialer0
IP route 0.0.0.0 0.0.0.0 Dialer0
!
!
access-list 22 allow 10.16.20.0
access-list 22 permit 10.16.20.0 0.0.0.255
Note access-list 101 * ACL SHEEP *.
access-list 101 deny ip 10.0.0.0 0.0.0.255 10.16.20.0 0.0.0.255
access-list 101 permit ip 10.0.0.0 0.0.0.255 any
access-list 115 permit ip 10.0.0.0 0.0.0.255 192.168.1.0 0.0.0.255
!
!
!
control plan
!
!
!
MGCP behavior considered range tgcp only
MGCP comedia-role behavior no
disable the behavior MGCP comedia-check-media-src
disable the behavior of MGCP comedia-sdp-force
!
profile MGCP default
!
!
!
!
!
Line con 0
no activation of the modem
line to 0
line vty 0 4
exec-timeout 0 0
preferred transport ssh
transport input telnet ssh
!
Scheduler allocate 20000 1000
!
end

OFFICE B

OFFICE-B-DG host name
!
boot-start-marker
boot-end-marker
!
AQM-registry-fnf

!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login xauthlist local
AAA authorization exec default local
AAA authorization exec vty group xauthlocal
AAA authorization exec defaultlocal group bdbusers
AAA authorization groupauthor LAN
!
!
!
!
!
AAA - the id of the joint session
!
Crypto pki trustpoint TP-self-signed-1514396900
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 1514396900
revocation checking no
rsakeypair TP-self-signed-1514396900
!
!
TP-self-signed-1514396900 crypto pki certificate chain
certificate self-signed 01

quit smoking

!
!
8.8.8.8 IP name-server
no ip cef
No ipv6 cef
!
!
!
!
!
Authenticated MultiLink bundle-name Panel
!
!
!
!
!
!
!
license udi pid C887VAM-K9 sn FCZ191362Q7
!
!

!
!
!
!
VDSL controller 0
!
property intellectual ssh rsa SSH key pair name
!
!
crypto ISAKMP policy 1
md5 hash
preshared authentication
!
crypto ISAKMP policy 3
BA 3des
preshared authentication
Group 2
!
crypto ISAKMP policy 20
md5 hash
preshared authentication
encryption XXXX isakmp key address IP-OFFICE-A

!
ISAKMP crypto client configuration group remoteusers
key xxxx
DNS 192.168.1.10
WINS 192.168.1.10
rete.loc field
pool ippool
ACL 101
!
!
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
tunnel mode
Crypto ipsec transform-set esp - esp-md5-hmac xauathtransform
tunnel mode
Crypto ipsec transform-set esp - esp-md5-hmac rtpset
tunnel mode
!
!
!
Crypto-map dynamic dynmap 10
Set transform-set RIGHT
Crypto-map dynamic dynmap 20
Set transform-set RIGHT
!
!
map clientmap client to authenticate crypto list userathen
card crypto clientmap isakmp authorization list groupauthor
client configuration address map clientmap crypto answer
10 ipsec-isakmp crypto map clientmap Dynamics dynmap
20 ipsec-isakmp crypto map clientmap
peer IP-OFFICE-A value
Set transform-set RIGHT
match address 115
!
!
!
!
!
!
!
interface Loopback1
no ip address
!
ATM0 interface
no ip address
No atm ilmi-keepalive
PVC 8/35
aal5mux encapsulation ppp Dialer
Dialer pool-member 1
!
!
interface Ethernet0
no ip address
Shutdown
!
interface FastEthernet0
switchport access vlan 30
no ip address
!
interface FastEthernet1
switchport access vlan 30
no ip address
!
interface FastEthernet2
switchport access vlan 20
no ip address
!
interface FastEthernet3
switchport access vlan 10
no ip address
!
interface Vlan1
no ip address
Shutdown
!
Vlan30 interface
IP 192.168.1.254 255.255.255.0
IP nat inside
IP virtual-reassembly in
!
interface Dialer0
the negotiated IP address
NAT outside IP
IP virtual-reassembly in
encapsulation ppp
Dialer pool 1
Authentication callin PPP chap Protocol
PPP pap sent-name to user
clientmap card crypto
!
router RIP
version 2
10.0.0.0 network
network 192.168.1.0
!
IP local pool ippool 10.16.20.201 10.16.20.250
IP forward-Protocol ND
no ip address of the http server
no ip http secure server
!
!
the IP nat inside source 1 interface Dialer0 overload list
overload of IP nat inside source list 101 interface Dialer0
IP nat inside source static tcp 192.168.1.100 5060 interface Dialer0 5060
IP nat inside source static tcp 192.168.1.100 5061 interface Dialer0 5061
IP nat inside source static tcp 192.168.1.100 5062 interface Dialer0 5062
IP nat inside source static tcp 192.168.1.100 5063 5063 Dialer0 interface
IP nat inside source static tcp 192.168.1.100 5064 interface Dialer0 5064
IP nat inside source static udp 192.168.1.100 5060 interface Dialer0 5060
IP nat inside source static udp 192.168.1.100 5061 interface Dialer0 5061
IP nat inside source static udp 192.168.1.100 5062 interface Dialer0 5062
IP nat inside source static udp 192.168.1.100 5063 5063 Dialer0 interface
IP nat inside source static udp 192.168.1.100 5064 interface Dialer0 5064
IP nat inside source static tcp 192.168.1.100 3541 interface Dialer0 3541
IP nat inside source static udp 192.168.1.100 3541 interface Dialer0 3541
IP route 0.0.0.0 0.0.0.0 Dialer0
!
!
sheep allowed 10 route map
corresponds to the IP 150 101
!
access-list 22 allow 10.16.20.0
access-list 22 permit 10.16.20.0 0.0.0.255
access list 101 deny ip 192.168.1.0 0.0.0.255 10.16.20.0 0.0.0.255
ACCESS-list 101 permit ip 192.168.1.0 0.0.0.255 any
access-list 115 permit ip 192.168.1.0 0.0.0.255 10.0.0.0 0.0.0.255
!
!
!
control plan
!
!
!
MGCP behavior considered range tgcp only
MGCP comedia-role behavior no
disable the behavior MGCP comedia-check-media-src
disable the behavior of MGCP comedia-sdp-force
!
profile MGCP default
!
!
!
!
!
Line con 0
no activation of the modem
line to 0
line vty 0 4
exec-timeout 0 0
password Password02
preferred transport ssh
transport input telnet ssh
!
Scheduler allocate 20000 1000
!
end

Thanks in advance for any help :)

the site at the other tunnel is mounted, but it does not pass traffic; What is the source and destination ip on the router that you are trying to ping the address

whenever you try to open the traffic from router A to router B, you must to the source of the traffic.

for ex,.

Router A-->10.1.1.1--fa0/0

Router B - 172.168.1.100

source of ping 172.168.1.100 router # 10.1.1.1

After doing the pings, send the output of the show counterpart of its crypto ipsec at both ends

VPN site to Site VPN dynamic + XAUTH Catch 22

Hello world

I'm working on a PIX 515e with 6.3 (3) 132 installed. I'm having a problem of setting up a new VPN connection from site to site with a dynamic VPN are already in place.

The problem is that the card encryption has xauth specified using the command 'authentication of customer card crypto'. As it is my understanding that it is not possible to assign several cryptographic cards on the same interface, the new tunnel from site to site I am creating also requires xauth because its definition is under the same encryption card - which is a problem because the remote device does not support.

Is there a way around this issue, or is the only thing we can do is to disable xauth and reconfigure endpoint on the other end of the dynamic connection?

Thanks in advance

Excerpt from the configuration:

map mymap 10-isakmp ipsec crypto dynamic dynmap

MYmap 22 ipsec-isakmp crypto map

correspondence address card crypto mymap 22 122

card crypto mymap 22 set counterpart x.x.x.x

card crypto mymap 22 transform-set 3des

client authentication card crypto mymap AuthOutbound

mymap outside crypto map interface

Considering that:

TUN 22 ipsec-isakmp crypto map

crypto TUN 22 card matches the address 122

card crypto TUN 22 set counterpart x.x.x.x

card crypto TUN 22 value transform-set 3des

TUN interface card crypto outside

Might work, except the interface card switching to TUN crypto map would break the dynamic VPN.

Hello

The dynamic encryption card normally requires XAUTH for VPN clients.

If you want to set up a tunnel from Site to Site and avoid XAUTH on this tunnel, you can do the following:

# address x.x.x.x No.-xauth isakmp encryption key

The idea is to disable XAUTH for each peer Site to Site specific in this way (dynamic clients will continue to work with XAUTH).

Federico.

Problems with site-to-site vpn

Hello world

I recently received the mission assigned to the site to site vpn configuration and this is my first time. I'm trying to set up a vpn with pix 501 but short questions site. I managed to get that below, but I'm stuck now and do not know what could be the problem. Here's the debug output.

Any help is greatly appreciated on what could be the potential problem.

-AK

ISAKMP (0:0): sending of NAT - T vendor ID - rev 2 & 3
ISAKMP (0): early changes of Main Mode
crypto_isakmp_process_block:src:208.249.117.203, dest:70.91.20.245 spt:500 dpt:500
Exchange OAK_MM
ISAKMP (0): treatment ITS payload. Message ID = 0

ISAKMP (0): audit ISAKMP transform 1 against 20 priority policy
ISAKMP: 3DES-CBC encryption
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: preshared auth
ISAKMP: type of life in seconds
ISAKMP: duration of life (basic) of 28800
ISAKMP (0): atts are acceptable. Next payload is 0
ISAKMP (0): load useful treatment vendor id

ISAKMP (0): ITS been pre-shared key, using id ID_IPV4_ADDR type authentication

to return to the State is IKMP_NO_ERROR
crypto_isakmp_process_block:src:208.249.117.203, dest:70.91.20.245 spt:500 dpt:5
00
Exchange OAK_MM
ISAKMP (0): processing KE payload. Message ID = 0

ISAKMP (0): processing NONCE payload. Message ID = 0

ISAKMP (0): load useful treatment vendor id

ISAKMP (0): load useful treatment vendor id

ISAKMP (0): provider v6 code received xauth

ISAKMP (0): load useful treatment vendor id

ISAKMP (0): addressing another box of IOS!

ISAKMP (0): load useful treatment vendor id

ISAKMP (0): addressing a VPN3000 concentrator

ISAKMP (0): ID payload
next payload: 8
type: 1
Protocol: 17
Port: 0
Length: 8
ISAKMP (0): the total payload length: 12
to return to the State is IKMP_NO_ERROR
crypto_isakmp_process_block:src:208.249.117.203, dest:70.91.20.245 spt:500 dpt:5
00
Exchange OAK_MM
ISAKMP (0): processing ID payload. Message ID = 0
ISAKMP (0): HASH payload processing. Message ID = 0
ISAKMP (0): keep treatment alive: proposal = 32767/32767 sec., real = 3276/2 sec.

ISAKMP (0): load useful treatment vendor id

ISAKMP (0): Peer Remote supports dead peer detection

ISAKMP (0): SA has been authenticated.

ISAKMP (0): start Quick Mode changes, 413131006:189fe0feIPSEC (key_e M - ID
(Display): had an event of the queue...
IPSec (spi_response): spi 0x3e9451fa graduation (1049907706) for SA
from 208.249.117.203 to 70.91.20.245 for prot 3

to return to the State is IKMP_NO_ERROR
ISAKMP (0): send to notify INITIAL_CONTACT
ISAKMP (0): sending message 24578 NOTIFY 1 protocol
Peer VPN: ISAKMP: approved new addition: ip:208.249.117.203/500 Total VPN peer: 1
Peer VPN: ISAKMP: ip:208.249.117.203/500 Ref cnt is incremented to peers: 1 Total VPN
Peers: 1
crypto_isakmp_process_block:src:208.249.117.203, dest:70.91.20.245 spt:500 dpt:5
00
ISAKMP (0): processing DELETE payload. Message ID = 3425658127, spi size = 16
ISAKMP (0): delete SA: src 70.91.20.245 dst 208.249.117.203
to return to the State is IKMP_NO_ERR_NO_TRANS
ISADB: Reaper checking HIS 0xac149c, id_conn = 0 DELETE IT!

Peer VPN: ISAKMP: ip:208.249.117.203/500 Ref cnt decremented to peers: 0 Total VPN
Peers: 1
Peer VPN: ISAKMP: deleted peer: ip:208.249.117.203/500 VPN peer Total: 0IPSEC (ke
y_engine): got an event from the queue.
IPSec (key_engine_delete_sas): rec would remove the ISAKMP notify
IPSec (key_engine_delete_sas): remove all SAs shared with 208.249.117.203
IPSec (key_engine): request timer shot: count = 2,.
local (identity) = 70.91.20.245, distance = 208.249.117.203.
local_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4),
remote_proxy = 206.200.22.0/255.255.255.0/0/0 (type = 4)

Hello

Newspapers, I see you are using a VPN 3000 Concentrator as the remote vpn end point. Now, also of the debugs next section is interesting:

local (identity) = 70.91.20.245, distance = 208.249.117.203.
local_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4),
remote_proxy = 206.200.22.0/255.255.255.0/0/0 (type = 4)

-Looks like our traffic interesting PIX and the hub are not mirrors of each other, and does not. Can you please paste the PIX here cryptographic access lists, so that I can analyze the entries.

-Also, please make sure that you have followed all the steps during the vpn configuration according to the following links:

If your PIX is running at version 7.x and more: http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a008064a06f.shtml

If your PIX is running version 6.3.x: http://www.cisco.com/en/US/products/hw/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml

Once you check the config on PIX and concentrator, please provide me with the output of "sh cry isa his" and "sh cry ipsec his ' of the PIX. With this release, we can continue to troubleshoot if there is more questions.

Let me know if this can help,

See you soon,.

Christian V

Latest version of Firefox has problems loading sites, trying to load Google Analytics. No error message, just a page that won't load. How can I stop this?

Latest version of Firefox has some sites loading problems, it tries to load and gets then supported loading Google Analytics. No error message, just a page that won't load. How can I get rid of this, it is a "pain in the neck."

URL of affected sites

http://

Which websites do you have this problem?

Just did my laptop, tried to do windows updates and get a message T "here has been a problem the site witt" and can not open the page I requested at this time.

Just, I redid my laptop using my system recovery disks. I went to windows update and get this msg when I click on Express.com: the site has encountered a problem and cannot display the page you are trying to view.

Original title: I redid all my laptop. I went to windows update and get a message that says: there was a problem witht the site and I wanted that the pag can not open the page I have requessted at this time.

You must download and install Windows XP Service Pack 2 (if not already installed) followed in Windows XP Service Pack 3. You will find two of them at http://www.microsoft.com/downloads - download the "Network Installation Package" for the two and ignore the part about them being only for the professionals - the parcel I recommend you download will install with or without network connection.

the 3510 Office jet printer: printing problem on sites like Amazon and Ebay shipping labels

When you try to print a label created by Amazon or Ebay, I have a problem. When the tag appears and I click on the "print to the selected printer", instead of going to the print to print preview screen... I am taken to a Web site, home page specifically Oracles. whenever this happens when I try to print a label in this way.

The only way I can print the label's screen capture screen and print the label as image file.

I've never seen this problem before never.

Clues how to move printing, directly to a Web site?

Hello

This is probably how they create labels. Of many labels, statements... have to go through the process to create pdf files before you can print or save as pdf files. Please wait until the end before the print stage of the process.

Hope this helps

problem of site 2 site vpn

Greetings. We have a site 2 site vpn 2 asa5510-based work. The two sites are accessible internel network hosts, but we are unable to access all the services (such as the TFTP or CA)? or even ping hosts in the remote site of our local asa5510 network. It seems that ASA attempts to send packets directly through the default gw, bypasing the vpn tunnel. Any help would be very appreciate.

PS We checked the ACLs on both devices, so more than likely, this is not the problem.

Hello

Since you did not include public ip address of the external interface in the Crypto ACL, it's why he's not going in the tunnel.

Add Crypto ACL a statement where qualify you this statement outside the public ip address of the interface source and mirror image in the remote device.

HTH

Sangaré

Pls rate helpful messages

Problem with Site-to-Site VPN. VPN tunnel is broken but can ping

OK, so I am trying to understand why I can't not only appears when I sh crypto isakmp his or sh crypto ipsec his. I did the basic to site vpn settings to another and I can't ping on both networks fine no problem. So, when I ping from one pc to the address 172.16.0.0 192.168.0.0 network network there is no problem at all because the pings are very well received. But when I go to sh crypto isakmp sa, there's simply nothing and I can't for the life of understand me why. I watched my sh run for both routers and all seems well, but I guess I could be overlooking something. I would really appreciate if someone could help me to diagnose this problem.

I've attached my plotter file of package and two routers use the binary password. I also have the sh run two routers also attached.

I'm not on any of the router 172.16.0.0/24 only 172.16.0.0/16 and I think that is the question.

In Crypto ACL you have on the router of branch:

!

S2S-VPN-TRAFFIC extended IP access list

Licensing ip 192.168.0.0 0.0.0.255 172.16.0.0 0.0.0.255

If it should not be:

!

S2S-VPN-TRAFFIC extended IP access list

Licensing ip 192.168.0.0 0.0.0.255 172.16.0.0 0.0.255.255

and coursed mirrored on the main router.

If this isn't the case, you are saying that some ping between 192.168.0.x and 172.16.0.x is going ok. Can you please indicate exactly that one? I could see that you have attached a package tracer, but I couldn't open it.

IPSec site to site config question

Hi all

I want to config vpn site to site between cisco 871w and openswan on CentOS way.

I found that it can direct press 'Enter' after command:

"crypto ipsec transform-set esp - aes 256 test"

In my mind, I know that ipsec can be configured not encryption in the esp Protocol. So, what happens if there is no MCHA for auth in this scenario?

Default hash method will MCHA took or something else?

Thank you

Drank Breya

If you do not configure a HMAC for your IPSec security associations, and then no HMAC is used. That should NEVER be done! There are examples on ORC showing encryption without authentication, and also older versions of the official courses Cisco Firewall did that. But it is a non-secure config because he knows attacks against IPSec if you are not using authentication. Use always the ESP with a HMAC!

--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni

Problem of site 2 site config dynamic to static

Similar Questions

URL of affected sites

Maybe you are looking for