Problem with IPSec VPN ISA500 & login questions (multiple devices)

Similar Questions

• Problem with IPsec VPN between ASA and router Cisco - ping is not response

  Hello

  I don't know because the IPsec VPN does not work. This is my setup (IPsec VPN between ASA and R2):

  my network topology data:

  LAN 1 connect ASA - 1 (inside the LAN)

  PC - 10.0.1.3 255.255.255.0 10.0.1.1

  ASA - GigabitEthernet 1: 10.0.1.1 255.255.255.0

  -----------------------------------------------------------------

  ASA - 1 Connect (LAN outide) R1

  ASA - GigabitEthernet 0: 172.30.1.2 255.255.255.252

  R1 - FastEthernet 0/0: 172.30.1.1 255.255.255.252

  ---------------------------------------------------------------------

  R1 R2 to connect

  R1 - FastEthernet 0/1: 172.30.2.1 255.255.255.252

  R2 - FastEthernet 0/1: 172.30.2.2 255.255.255.252

  R2 for lan connection 2

  --------------------------------------------------------------------

  R2 to connect LAN2

  R2 - FastEthernet 0/0: 10.0.2.1 255.255.255.0

  PC - 10.0.2.3 255.255.255.0 10.0.2.1

  ASA configuration:

  1 GigabitEthernet interface
  nameif inside
  security-level 100
  IP 10.0.1.1 255.255.255.0
  no downtime
  interface GigabitEthernet 0
  nameif outside
  security-level 0
  IP 172.30.1.2 255.255.255.252
  no downtime
  Route outside 0.0.0.0 0.0.0.0 172.30.1.1

  ------------------------------------------------------------

  access-list scope LAN1 to LAN2 ip 10.0.1.0 allow 255.255.255.0 10.0.2.0 255.255.255.0
  object obj LAN
  subnet 10.0.1.0 255.255.255.0
  object obj remote network
  10.0.2.0 subnet 255.255.255.0
  NAT (inside, outside) 1 static source obj-local obj-local destination obj-remote control remote obj non-proxy-arp static

  -----------------------------------------------------------
  IKEv1 crypto policy 10
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 3600
  Crypto ikev1 allow outside
  crypto isakmp identity address

  ------------------------------------------------------------
  tunnel-group 172.30.2.2 type ipsec-l2l
  tunnel-group 172.30.2.2 ipsec-attributes
  IKEv1 pre-shared-key cisco123
  Crypto ipsec transform-set esp-aes-192 ASA1TS, esp-sha-hmac ikev1

  -------------------------------------------------------------
  card crypto ASA1VPN 10 is the LAN1 to LAN2 address
  card crypto ASA1VPN 10 set peer 172.30.2.2
  card crypto ASA1VPN 10 set transform-set ASA1TS ikev1
  card crypto ASA1VPN set 10 security-association life seconds 3600
  ASA1VPN interface card crypto outside

  R2 configuration:

  interface fastEthernet 0/0
  IP 10.0.2.1 255.255.255.0
  no downtime
  interface fastEthernet 0/1
  IP 172.30.2.2 255.255.255.252
  no downtime

  -----------------------------------------------------

  router RIP
  version 2
  Network 10.0.2.0
  network 172.30.2.0

  ------------------------------------------------------
  access-list 102 permit ahp 172.30.1.2 host 172.30.2.2
  access-list 102 permit esp 172.30.1.2 host 172.30.2.2
  access-list 102 permit udp host 172.30.1.2 host 172.30.2.2 eq isakmp
  interface fastEthernet 0/1
  IP access-group 102 to

  ------------------------------------------------------
  crypto ISAKMP policy 110
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 42300

  ------------------------------------------------------
  ISAKMP crypto key cisco123 address 172.30.1.2

  -----------------------------------------------------
  Crypto ipsec transform-set esp - aes 128 R2TS

  ------------------------------------------------------

  access-list 101 permit tcp 10.0.2.0 0.0.0.255 10.0.1.0 0.0.0.255

  ------------------------------------------------------

  R2VPN 10 ipsec-isakmp crypto map
  match address 101
  defined by peer 172.30.1.2
  PFS Group1 Set
  R2TS transformation game
  86400 seconds, life of security association set
  interface fastEthernet 0/1
  card crypto R2VPN

  I don't know what the problem

  Thank you

  If the RIP is not absolutely necessary for you, try adding the default route to R2:

  IP route 0.0.0.0 0.0.0.0 172.16.2.1

  If you want to use RIP much, add permissions ACL 102:

  access-list 102 permit udp any any eq 520

• Problem with Tunnel VPN L2L between 2 ASA´s

  Hi guys,.

  I have some problems with my VPN Site to site tunnel between 2 ASA (5520/5505).

  I watched a lot of videos on youtube, but I can't find out why the tunnel does not...

  Both devices can ping eachothers WAN IP address (outside interfaces), but I don't see any traffic between the 2 sites. It seems that the tunnel is not open to everyone. When i PING from the local to the Remote LAN (which should be an interesting traffic for the tunnel...), the its IKEv1 remains empty...

  Am I missing something? I can't understand it more why same phase 1 is not engaged.

  You NAT won't. In your config file traffic is NATted initially and then does not match any more crypto ACL. You must move the rule dynamic NAT/PAT until the end of the table on two ASAs NAT:

   no nat (INSIDE,OUTSIDE) source dynamic any interface nat (INSIDE,OUTSIDE) after-auto source dynamic any interface

• Someone at - he had problems with 9.2.1 and pairing Bluetooth devices?  My iPhone will not be connected or pair of devices.  Devices to recognize the iPhone 6, but the will of the iPhone 6 does not recognize the device.  Is there a problem with 9.2.1?

  Someone at - he had problems with 9.2.1 and pairing Bluetooth devices?  My iPhone will not be connected or pair of devices.  Devices to recognize the iPhone 6, but the will of the iPhone 6 does not recognize the device.  Is there a problem with 9.2.1?

  Kev2012 wrote:

  Someone at - he had problems with 9.2.1 and pairing Bluetooth devices?  My iPhone will not be connected or pair of devices.  Devices to recognize the iPhone 6, but the will of the iPhone 6 does not recognize the device.  Is there a problem with 9.2.1?

  It would depend on what you're trying to link to?

  Here are the supported Bluetooth profiles an Apple device can connect to iOS: Bluetooth profiles supported - Apple Support

• Context with IPSec VPN

  Hi friends,

  I have a question for the scenario below.

  I need to create a Site-Site IPSec VPN in the firewall mode.

  Is it possible to create the tunnel.

  I have ASA 5510 Security Plus with Ver 8.3

  Thanks in advance.

  In your case, you ASA in multiple-context to allow VPN to the amp.

  There is no problem with that.

  The only restrictions are that an ASA in multiple context will not work as a VPN endpoint (apart from a tunnel admin)... but you can pass the traffic or VPN traffic as in ASAs in simple mode.

  Federico.

• PIX 515E (7.0.1) - problem with the VPN connection between inside and outside

  Hello

  I ve creates a VLAN on the pix.

  In this VLAN, users are allowed to connect only to the Internet. Everything is fine, but when trying to connect with his VPN Client to their company, it has problems... (Outside traffic flow, but no traffic came back.)

  Is the only solution for this problem to create a Pool of Nat with public ip addresses, one to one mapping, or is there another solution with a public IP address (NAT on PAT) possible for this problem?

  Thanks for your replies.

  D.

  The problem is that the esp is an IP Protocol, so PAT will not work in this scenario. When the return traffic returns to pix he doesn't know how to get to the inside host. The only way to do this is by adding a static nat (1 to 1 mapping) and create a rule to allow esp. Is what type of vpn client? Microsoft vpn? Cisco vpn? If cisco VPN, perhaps, they can use NAT - T on the vpn that overcomes the question PAT by encapsulating ipsec within UDP packets. You need to talk to the admin VPN and itself it allow.

  -kevin

• "ITS creation failed" problem for IPSec VPN

  An ASA 5100 is used to provide VPN access for my business. The configuration was made by a permeable man who has been missing for some time, and the configuration used to be OK until this morning. This morning, some users reported that their VPN would have fallen once got connected. I checked the ASA and ASDM, I see every time when user deletes, it IPSec tunnel is always action. Furthermore, I faked the problem and got the newspaper of errors such as:

  1 11:14:45.898 12/06/07 Sev = WARNING/3 IKE/0xE3000065 could not find an IKE SA for 10.2.1.8. Abandoned KEY_REQ.

  2 11:14:45.898 12/06/07 Sev = WARNING/2 IKE/0xE3000099 could not open the P2 generate a new key: error detected(Initiate:176)

  3 11:14:45.898 12/06/07 Sev = WARNING/2 IKE/0xE3000099 cannot open the QM (IKE_MAIN:458)

  On the side of the AS I did "debug crypto isakmp" and 'debug crypto ipsec' and I got the following errors:

  iscoasa # ERROR IPSEC: expiration of the timer of the asynchronous operation, SPI: 0x114CA5B6, user: roeladmin, peer: 202.x.x.70, time: 2 seconds, ctm_ipsec_create_sa:856

  IPSEC ERROR: Material outside ITS create command failed, SPI: 0x114CA5B6, error code: 0 x 17

  IPSEC ERROR: Asynchronous Operation timeout expired, SPI: 0x61BE2022, user: roeladmin, peer: 202.x.x.70, time: 2 seconds, ctm_ipsec_create_sa:856

  IPSEC ERROR: Cannot add a user auth, SPI input: 0x61BE2022, user: roeladmin, peer: 202.172.62.70

  IPSEC ERROR: Cannot create an inbound SA SPI: 0x61BE2022 document

  IPSEC ERROR: Unable to complete the command of IKE UPDATE

  12 June at 14:25:13 [IKEv1]: Group = LANWORKS, Username = roeladmin, IP = 202.172.62.70, error QM WSF (P2 struct & 0 x 4699058, mess id 0xf37ec6f4).

  12 June at 14:25:13 [IKEv1]: Group = LANWORKS, Username = roeladmin, IP = 202.172.62.70, peer table correlator Removing failed, no match!

  IPSEC ERROR: Material Inbound ITS create command failed, SPI: 0x61BE2022, error code: 0 x 17

  It shows that ITS creation has failed. But I can't find the problem with the configuration. Can someone help me on this? Thank you

  Outgoing material ITS create command failed, SPI: 0x114CA5B6, error code: 0 x 17

  It is a hardware problem, reset the firewall and it will work, I saw 4 times in different ASAs

  Please hate the post if help.

• Problem with IPSEC tunnel between Cisco PIX and Cisco ASA

  Hi all!

  Have a strange problem with one of our tunnel ipsec for one of our customers, we can open the tunnel of the customers of the site, but not from our site, don't understand what's wrong, if it would be a configuration problem should can we not all up the tunnel.

  On our side as initiator:

  Jan 14 13:53:26 172.27.1.254% PIX-7-702208: ISAKMP Phase 1 Exchange started (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% PIX-7-702210: Exchange of ISAKMP Phase 1 is complete (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% 6-PIX-602202: ISAKMP connected session (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% PIX-6-602201: Phase 1 ISAKMP Security Association created (local 1.1.1.1/500 (initiator), 2.2.2.2/500 remotely, authentication = pre-action, encryption = 3DES-CBC, hash = SHA, group = 2, life = 86400 s)

  Jan 14 13:53:26 172.27.1.254% PIX-7-702209: ISAKMP Phase 2 Exchange started (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% PIX-7-702201: ISAKMP Phase 1 delete received (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:26 172.27.1.254% PIX-6-602203: ISAKMP disconnected session (local 1.1.1.1 (initiator), remote 2.2.2.2)

  Jan 14 13:53:56 172.27.1.254% PIX-7-702303: sa_request, CBC (MSG key in English) = 1.1.1.1, dest = 2.2.2.2, src_proxy = 172.27.1.10/255.255.255.255/0/0 (type = 1), dest_proxy = 192.168.100.18/255.255.255.255/0/0 (type = 1), Protocol is ESP transform = lifedur hmac-sha-esp, esp-3des 28800 = s and 4608000 Ko, spi = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 4004

  The site of the customer like an answering machine:

  14 jan 11:58:23 172.27.1.254% PIX-7-702208: ISAKMP Phase 1 Exchange started (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  14 jan 11:58:23 172.27.1.254% PIX-7-702210: Exchange of ISAKMP Phase 1 is complete (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  14 jan 11:58:23 172.27.1.254% 6-PIX-602202: ISAKMP connected session (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  14 jan 11:58:23 172.27.1.254% PIX-6-602201: Phase 1 ISAKMP Security Association created (local 1.1.1.1/500 (answering machine), distance 2.2.2.2/500, authentication = pre-action, encryption = 3DES-CBC, hash = MD5, group = 1, life = 86400 s)

  14 jan 11:58:23 172.27.1.254% PIX-7-702209: ISAKMP Phase 2 Exchange started (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  14 jan 11:58:23 172.27.1.254% PIX-6-602301: its created, (his) sa_dest = 2.2.2.2, sa_prot = 50, sa_spi = 0x9de820bd (2649235645) sa_trans = sa_conn_id of hmac-sha-esp, esp-3des = 116

  14 jan 11:58:23 172.27.1.254% PIX-7-702211: Exchange of ISAKMP Phase 2 is complete (local 1.1.1.1 (answering machine), 2.2.2.2 remote)

  Jan 14 12:28:54 172.27.1.254% PIX-6-602302: SA deletion, (his) sa_dest = 2.2.2.2, sa_prot = 50, sa_spi = 0x9de820bd (2649235645), sa_trans = esp-3desesp-sha-hmac, sa_conn_id = 116

  Kind regards

  Johan

  From my experience when a tunnel is launched on one side, but it is not on the other hand, that the problem is with an inconsistency of the isakmp and ipsec policies, mainly as ipsec policies change sets and corresponding address with ASA platform when a tunnel is not a statically defined encryption card he sometimes use the dynamic tag to allocate this vpn connection. To check if this is the case go ahead and make a "crypto ipsec to show his" when the tunnel is active on both sides, see on the SAA if the corresponding tunnel is the static encryption card set or if it presents the dynamic encryption card.

  I advise you to go to the settings on both sides and ensure that they are both in the opposite direction.

• site noncisco routers with IPSec VPN

  Hello

  I try to connect Router 2911 cisco routers noncisco (HP, TPlink) using ipsec site to site vpn with crypto-cards.

  the problem is that vpn ensuring shows '#send error' if command "crypto isakmp identity dn" is used (we use it for authentication of certificate based for cisco vpn clients). When I remove the command, vpn works great with noncisco devices.

  Please can you advice if there is no option on cisco ios to fix the problem.

  Thank you

  Giga

  good,

  try to use the isakmp profile something like below:

  crypto isakmp profile test
  function identity address 1.1.1.1 255.255.255.255

  under card crypto profiles isakmp as below:

  test 1 test ipsec-isakmp crypto map

  -Altaf

• Problem with ping VPN cisco 877

  Hi all!

  I have a working VPN between a fortigate and a Cisco.

  I have a problem with ping network behind the cisco of the network behind the forti.

  When I ping to vlan2 cisco without problem (192.168.252.1) interface, but I can't ping a server in the vlan2 (192.168.252.2) behind the cisco.

  However the Cisco I can ping the server. In the forti, I see that ping to the interface vlan2 and server in vlan2 take in the same way, and I can see package.

  I post my config could see it it as blocking the ping from 10.41.2.36 to 192.168.252.2 while 192.168.252.1 ping is OK?

  IPSEC #show run
  Building configuration...

  Current configuration: 3302 bytes
  !
  ! Last modification of the configuration at 14:42:17 CEDT Friday, June 25, 2010
  ! NVRAM config update at 14:42:23 CEDT Friday, June 25, 2010
  !
  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime localtime show-time zone
  encryption password service
  !
  IPSEC host name
  !
  boot-start-marker
  boot-end-marker
  !
  logging buffered 1000000
  enable secret 5 abdellah
  !
  No aaa new-model
  clock timezone GMT 1
  clock to summer time CEDT recurring last Sun Mar 02:00 last Sun Oct 03:00
  !
  !
  dot11 syslog
  IP cef
  No dhcp use connected vrf ip
  DHCP excluded-address IP 192.168.254.0 192.168.254.99
  DHCP excluded-address IP 192.168.254.128 192.168.254.255
  !
  IP dhcp DHCP pool
  network 192.168.254.0 255.255.255.0
  router by default - 192.168.254.254
  Server DNS A.A.A.A B.B.B.B
  !
  !
  no ip domain search
  name of the IP-server A.A.A.A
  name of the IP-server B.B.B.B
  !
  !
  !
  !
  !
  crypto ISAKMP policy 1
  BA aes 256
  preshared authentication
  Group 5
  ISAKMP crypto key ciscokey address IP_forti
  !
  !
  Crypto ipsec transform-set esp - aes 256 esp-sha-hmac vpntest
  !
  myvpn 10 ipsec-isakmp crypto map
  defined by peer IP_forti
  Set transform-set vpntest
  match address 101
  !
  Archives
  The config log
  hidekeys
  !
  !
  !
  !
  !
  interface Tunnel0
  IP 2.2.2.1 255.255.255.252
  source of Dialer0 tunnel
  destination of IP_forti tunnel
  myvpn card crypto
  !
  ATM0 interface
  bandwidth 320
  no ip address
  load-interval 30
  No atm ilmi-keepalive
  DSL-automatic operation mode
  !
  point-to-point interface ATM0.1
  MTU 1492
  bandwidth 160
  PVC 8/35
  VBR - nrt 160 160
  PPPoE-client dial-pool-number 1
  !
  !
  interface FastEthernet0
  switchport access vlan 2
  !
  interface FastEthernet1
  !
  interface FastEthernet2
  !
  interface FastEthernet3
  switchport access vlan 2
  !
  interface Vlan1
  IP 192.168.20.253 255.255.255.0
  IP nat inside
  no ip virtual-reassembly
  !
  interface Vlan2
  IP 192.168.252.1 255.255.255.0
  IP nat inside
  IP virtual-reassembly
  !
  interface Dialer0
  bandwidth 128
  the negotiated IP address
  NAT outside IP
  no ip virtual-reassembly
  encapsulation ppp
  load-interval 30
  Dialer pool 1
  Dialer-Group 1
  KeepAlive 1 2
  Authentication callin PPP chap Protocol
  PPP chap hostname [email protected] / * /
  PPP chap password 7 abdelkrim
  myvpn card crypto
  !
  IP forward-Protocol ND
  IP route 0.0.0.0 0.0.0.0 Dialer0
  IP route 10.41.2.32 Tunnel0 255.255.255.240
  !
  no ip address of the http server
  no ip http secure server
  The dns server IP
  translation of nat IP tcp-timeout 5400
  no ip nat service sip 5060 udp port
  overload of IP nat inside source list NAT interface Dialer0
  !
  IP access-list standard BROADCAST
  permit of 0.0.0.0
  deny all
  !
  NAT extended IP access list
  IP enable any host IP_cisco
  deny ip 192.168.252.0 0.0.0.255 10.41.2.32 0.0.0.31
  !
  access-list 101 permit ip 192.168.252.0 0.0.0.255 10.41.2.32 0.0.0.31
  public RO SNMP-server community
  3 RW 99 SNMP-server community
  SNMP-server community a RO
  SNMP-Server RO community oneCommunityRead
  not run cdp
  !
  !
  !
  control plan
  !
  !
  Line con 0
  password 7 abdelkrim
  opening of session
  no activation of the modem
  line to 0
  line vty 0 4
  password 7 aaaaa
  opening of session
  escape character 5
  !
  max-task-time 5000 Planner
  NTP-period clock 17175037
  Server NTP B.B.B.B
  Server NTP A.A.A.A

  end

  Alex,

  It's your GRE tunnel:

  interface Tunnel0
  IP 2.2.2.1 255.255.255.252
  source of Dialer0 tunnel
  destination of IP_forti tunnel
  myvpn card crypto

  You also have routing set by it.

  You don't need a GRE tunnel, nor do you need the road to tunnel if you want just IPsec tunnel.

• Problem with the VPN site to site for the two cisco asa 5505

  Starting with cisco asa. I wanted to do a vpn site-to site of cisco. I need help. I can't ping from site A to site B and vice versa.

  Cisco Config asa1

  interface Ethernet0/0
  switchport access vlan 1
  !
  interface Ethernet0/1
  switchport access vlan 2
  !
  interface Vlan1
  nameif outside
  security-level 0
  IP address 172.xxx.xx.4 255.255.240.0
  !
  interface Vlan2
  nameif inside
  security-level 100
  IP 192.168.60.2 255.255.255.0
  !
  passive FTP mode
  network of the Lan_Outside object
  192.168.60.0 subnet 255.255.255.0
  network of the NETWORK_OBJ_192.168.1.0_24 object
  subnet 192.168.1.0 255.255.255.0
  network of the NETWORK_OBJ_192.168.60.0_24 object
  192.168.60.0 subnet 255.255.255.0
  object-group Protocol DM_INLINE_PROTOCOL_1
  ip protocol object
  icmp protocol object
  object-group Protocol DM_INLINE_PROTOCOL_2
  ip protocol object
  icmp protocol object
  object-group Protocol DM_INLINE_PROTOCOL_3
  ip protocol object
  icmp protocol object
  Access extensive list ip 192.168.60.0 Outside_cryptomap allow 255.255.255.0 192.168.1.0 255.255.255.0
  Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_3 of object-group a
  Outside_access_in list extended access allow DM_INLINE_PROTOCOL_1 of object-group a
  Inside_access_in list extended access allow DM_INLINE_PROTOCOL_2 of object-group a
  network of the Lan_Outside object
  NAT (inside, outside) interface dynamic dns
  Access-group Outside_access_in in interface outside
  Inside_access_in access to the interface inside group
  Route outside 0.0.0.0 0.0.0.0 172.110.xx.1 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  AAA authentication http LOCAL console
  Enable http server
  http 192.168.60.0 255.255.255.0 inside
  http 96.xx.xx.222 255.255.255.255 outside
  No snmp server location
  No snmp Server contact
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
  Crypto ipsec ikev2 ipsec-proposal OF
  encryption protocol esp
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 proposal ipsec 3DES
  Esp 3des encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES
  Esp aes encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES192
  Protocol esp encryption aes-192
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 AES256 ipsec-proposal
  Protocol esp encryption aes-256
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec pmtu aging infinite - the security association
  card crypto Outside_map 1 corresponds to the address Outside_cryptomap
  card crypto Outside_map 1 set peer 96.88.75.222
  card crypto Outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  card crypto Outside_map 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
  Outside_map interface card crypto outside
  trustpool crypto ca policy
  IKEv2 crypto policy 1
  aes-256 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 10
  aes-192 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 20
  aes encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 30
  3des encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 40
  the Encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  Crypto ikev2 allow outside
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  authentication crack
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 20
  authentication rsa - sig
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 30
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 40
  authentication crack
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 50
  authentication rsa - sig
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 60
  preshared authentication
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 70
  authentication crack
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 80
  authentication rsa - sig
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 90
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 100
  authentication crack
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 110
  authentication rsa - sig
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 120
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 130
  authentication crack
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 140
  authentication rsa - sig
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 150
  preshared authentication
  the Encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH stricthostkeycheck
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  inside access management

  dhcpd address 192.168.60.50 - 192.168.60.100 inside
  dhcpd allow inside
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  AnyConnect essentials
  internal GroupPolicy_96.xx.xx.222 group strategy
  attributes of Group Policy GroupPolicy_96.xx.xx.222
  VPN-tunnel-Protocol ikev1, ikev2
  username admin privilege 15 encrypted password f3UhLvUj1QsXsuK7
  tunnel-group 96.xx.xx.222 type ipsec-l2l
  tunnel-group 96.xx.xx.222 General-attributes
  Group - default policy - GroupPolicy_96.xx.xx.222
  96.XX.XX.222 group of tunnel ipsec-attributes
  IKEv1 pre-shared-key *.
  remote control-IKEv2 pre-shared-key authentication *.
  pre-shared-key authentication local IKEv2 *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  inspect the icmp error

  ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  Cisco ASA 2 config

  interface Ethernet0/0
  switchport access vlan 1
  !
  interface Ethernet0/1
  switchport access vlan 2
  !
  interface Vlan1
  nameif outside
  security-level 0
  IP address 96.xx.xx.222 255.255.255.248
  !
  interface Vlan2
  nameif inside
  security-level 100
  IP 192.168.1.254 255.255.255.0
  !
  passive FTP mode
  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface
  network of the Lan_Outside object
  subnet 192.168.1.0 255.255.255.0
  network of the NETWORK_OBJ_192.168.60.0_24 object
  192.168.60.0 subnet 255.255.255.0
  network of the NETWORK_OBJ_192.168.1.0_24 object
  subnet 192.168.1.0 255.255.255.0
  object-group Protocol DM_INLINE_PROTOCOL_1
  ip protocol object
  icmp protocol object
  object-group Protocol DM_INLINE_PROTOCOL_2
  ip protocol object
  icmp protocol object
  object-group Protocol DM_INLINE_PROTOCOL_3
  ip protocol object
  icmp protocol object
  object-group Protocol DM_INLINE_PROTOCOL_4
  ip protocol object
  icmp protocol object
  Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_2 of object-group 192.168.1.0 255.255.255.0 192.168.60.0 255.255.255.0
  Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_3 of object-group a
  Outside_access_in list extended access allow DM_INLINE_PROTOCOL_1 of object-group a
  Inside_access_in list extended access allow DM_INLINE_PROTOCOL_4 of object-group a
  pager lines 24
  Enable logging
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) static source NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.60.0_24 NETWORK_OBJ_192.168.60.0_24 non-proxy-arp-search of route static destination
  !
  network of the Lan_Outside object
  dynamic NAT (all, outside) interface
  Access-group Outside_access_in in interface outside
  Inside_access_in access to the interface inside group
  Route outside 0.0.0.0 0.0.0.0 96.xx.xx.217 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  AAA authentication http LOCAL console
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  http 172.xxx.xx.4 255.255.255.255 outside
  No snmp server location
  No snmp Server contact
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
  Crypto ipsec ikev2 ipsec-proposal OF
  encryption protocol esp
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 proposal ipsec 3DES
  Esp 3des encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES
  Esp aes encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES192
  Protocol esp encryption aes-192
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 AES256 ipsec-proposal
  Protocol esp encryption aes-256
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec pmtu aging infinite - the security association
  card crypto Outside_map 1 corresponds to the address Outside_cryptomap
  card crypto Outside_map 1 set peer 172.110.74.4
  card crypto Outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  card crypto Outside_map 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
  Outside_map interface card crypto outside
  trustpool crypto ca policy
  IKEv2 crypto policy 1
  aes-256 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 10
  aes-192 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 20
  aes encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 30
  3des encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 40
  the Encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  Crypto ikev2 allow outside
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  authentication crack
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 20
  authentication rsa - sig
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 30
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 40
  authentication crack
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 50
  authentication rsa - sig
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 60
  preshared authentication
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 70
  authentication crack
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 80
  authentication rsa - sig
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 90
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 100
  authentication crack
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 110
  authentication rsa - sig
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 120
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 130
  authentication crack
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 140
  authentication rsa - sig
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 150
  preshared authentication
  the Encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH stricthostkeycheck
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0

  dhcpd address 192.168.1.50 - 192.168.1.100 inside
  dhcpd allow inside
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  AnyConnect essentials
  internal GroupPolicy_172.xxx.xx.4 group strategy
  attributes of Group Policy GroupPolicy_172.xxx.xx.4
  L2TP ipsec VPN-tunnel-Protocol ikev1, ikev2
  username admin privilege 15 encrypted password f3UhLvUj1QsXsuK7
  tunnel-group 172.xxx.xx.4 type ipsec-l2l
  tunnel-group 172.xxx.xx.4 General-attributes
  Group - default policy - GroupPolicy_172.xxx.xx.4
  172.xxx.XX.4 group of tunnel ipsec-attributes
  IKEv1 pre-shared-key *.
  remote control-IKEv2 pre-shared-key authentication *.
  pre-shared-key authentication local IKEv2 *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  inspect the icmp error
  inspect the http

  For IKEv2 configuration: (example config, you can change to encryption, group,...)

  -You must add the declaration of exemption nat (see previous answer).

  -set your encryption domain ACLs:

  access-list-TRAFFIC IPSEC allowed extended LOCAL REMOTE - LAN LAN ip

  -Set the Phase 1:

  Crypto ikev2 allow outside
  IKEv2 crypto policy 10
  3des encryption
  the sha md5 integrity
  Group 5
  FRP sha
  second life 86400

  -Set the Phase 2:

  Crypto ipsec ikev2 ipsec IKEV2-PROPOSAL
  Esp aes encryption protocol
  Esp integrity sha-1 protocol

  -set the Group of tunnel

  tunnel-group REMOTE-PUBLIC-IP type ipsec-l2l
  REMOTE-PUBLIC-IP tunnel-group ipsec-attributes
  IKEv2 authentication remote pre-shared-key cisco123

  
  IKEv2 authentication local pre-shared-key cisco123

  -Define the encryption card

  address for correspondence CRYPTOMAP 10 - TRAFFIC IPSEC crypto map
  card crypto CRYPTOMAP 10 peer set REMOTE-PUBLIC-IP
  card crypto CRYPTOMAP 10 set ipsec ikev2-IKEV2-PROPOSAL
  CRYPTOMAP interface card crypto outside
  crypto isakmp identity address

  On your config, you have all these commands but on your VPN config, you mix ikev1 and ikev2. You have also defined political different ikev2. Just do a bit of cleaning and reached agreement on a 1 strategy for the two site (encryption, hash,...)

  Thank you

• Easy VPN with IPSec VPN L2L (Site - to - Site) in the same ASA 5505

  Hi Experts,

  We have an ASA 5505 in our environment, and currently two IPSec VPN L2L tunnels are established. But we intend to connect with VPN (Network Extension Mode) easy to another site as a customer. Is it possible to configure easy VPN configurations by keeping the currently active IPSec L2L VPN(Site-to-Site) tunnels? If not possible is there any work around?

  Here's the warning we get then tried to configure the easy VPN Client.

  NOCMEFW1 (config) # vpnclient enable

  * Delete "nat (inside) 0 S2S - VPN"

  * Detach crypto card attached to the outside interface

  * Remove the tunnel groups defined by the user

  * Remove the manual configuration of ISA policies

  CONFLICT of CONFIG: Configuration that would prevent the Cisco Easy VPN Remo success

  you

  operation was detected and listed above. Please solve the

  above a configuration and re - activate.

  Thanks and greetings

  ANUP sisi

  "Dynamic crypto map must be installed on the server device.

  Yes, dynamic crypto is configured on the EasyVPN server.

  Thank you

• Using dynamic PAT with IPSec VPN

  Hello

  I will say first of all thanks for reading this post.

  My goal is to create a dynamic PAT for 5 private host 1 ip address public, then to allow this ip address public 1 via an ipsec tunnel.

  I have an ASA5555 running on code 9.2 (1).  Here's what I have so far:

  network of object obj - 12.12.12.12 {mapped address}

  host 12.12.12.12

  object-group, LAN {address}

  host 10.0.0.1

  host 10.0.0.2

  host 10.0.0.3

  host 10.0.0.4

  host 10.0.0.5

  NAT (inside, outside) dynamic source LOCAL obj - 12.12.12.12

  First question - haven't set up that PAT correctly? I'm trying to PAT the local private addresses on the public address 12.12.12.12

  Now I would use 12.12.12.12 as interesting traffic and leave it in a vpn tunnel:

  access-list 1 extended permit ip host 12.12.12.12 object-group Remote_Network

  This configuration seems correct?  Is there another way to accomplish the same task?

  Thank you for your time.

  Looks good so far.

  But if this PAT is only for VPN traffic, then you can change the policy-nat NAT rule:

   nat (inside,outside) source dynamic LOCAL obj-12.12.12.12 destination static Remote_Network Remote_Network

• Bypass the router upstream company ACL with IPSEC VPN

  Hello

  My headquarters has a routing infrastructure company. I want to configure a Site VPN to IPSEC as a solution of webvpn AnyConnect for my users through the company. If the security guys to create an ACL on the router upstream from my Cisco ASA 5585 to allow IPSEC between 28 (the stretch between my external interface of ASA and the trunk of PO on the upstream router) then I can send ip a whole between my inside interface subnet and subnet within the interface on the ASA distant (still on the company's infrastructure holding constant and correct routing. In short, if a packet is encrypted in an IPSEC packet, IPSEC is not filtered, you can send any traffic, even if it is AS restrictive on a router upstream of the LCA, correct?

  Thank you!

  Matt

  CCNP

  You are right, the router can not look in the VPN package. So anything that is transported inside the VPN, it bypasses security company-ACL.

  For VPN traffic to your ASA, you need the following protocols/ports:

  1. UDP/500, UDP4500, IP/50 for IPsec
  2. UDP/443 for AnyConnect with SSL/TLS, TCP/443

• Problem with the store and several questions.

  I tried all the methods listed below:

  Method 1: Make sure that User Account Control (UAC) is enabled.

  Press the Windows key and from the splash screen, type "UAC" and on the right, select settings.
  Select change user account control settings and check here.

  Method 2: Check the date & time zone is correct:

  Follow these steps to change the time.

  a. double-click the current time on the lower right of your screen.

  b. then click Change hour date, then click on the button to change time zone

  c. Select your time zone and the tick to automatically adjust clock for the time being, then press OK

  d. press on apply, then OK.

  Method 3: Run the network troubleshooting and check if you can connect to store.

  Follow the steps to run the network troubleshooter utility:

  a. press the keys Windows + C on your keyboard to show the charms.

  b. type Troubleshooting , and then clicksolving problems under settings.

  c. now, tap network troubleshooting in the optionSearch .

  d. clickutility troubleshooting networkto run the troubleshooter.

  Method 4: If you use a proxy connection, then try to disable the proxy and then check if the problem persists.

  Follow the steps to disable the proxy:

  a. open Internet Explorer

  b. click on the Tools buttonand then click onInternet Options

  c. click on the Connections taband then clickLAN settings

  d. uncheck it Server Proxy use.

  e. click on apply then Ok to save the changes.

  Now, check if you can access store.

  Method 5: Cache reset Store.
  Follow the steps and check out them.
  (a) right click on the start screen
  (b) click on run
  Type c) in WSReset.exe
  (d) press enter
  (e) restart the computer and check.

  Method 6: analysis Run SFC
  (a) right click on the lower left corner of the screen and select 'Admin command prompt.
  (b) type following command, and then press ENTER: "sfc/scannow".

  Method 7: I suggest that you disable the antivirus installed on the computer.

  Method 8: CDevil Windows Firewall settings

   

  (a) Type in the Panel on the Start Page.

  (b) on the left side, click on Control Panel.

  (c) click on Windows Firewall.

  (d) in the left pane, click "allow an app or feature through Windows Firewall."

  (e) under the features and applications allowed, look for store.

  (f) make sure that you have a click in private or Public.

  (g) then see if you can open the Windows store.

  Not a SINGLE one of these methods have worked. When I go to my home screen and click on store, he told me 'we could not connect to the Bank. This could have happened due to a server problem or a network connection has expired. Please wait a few minutes and try again. "I did it on my network troubleshooting, all right, I am able to connect to everything, but I've NEVER been able to connect to the store. Not only can I not connect to the store to upgrade to 8.1 Windows, but I can't create restore points. Not only that, but the backlight on my keyboard, no matter which option to choose, is always on when I type, even if I say it stays off. In addition, with Windows 8, I was promised the "quick start" where he takes no time to start, it takes more to start my computer windows 8 as it did my 4 years updated to the windows computer 7. Also, I can't start in Safe Mode or the clean boot. Whenever I try to perform the clean boot by using the options in the window manager and the configuration tasks system, when the computer reboots, everyone who opens are reset to zero and it doesn't work. I can also perform an update of the system. I want to just upgrade to 8.1 windows, but I'm not without the WS and NONE of the methods I have found work. I'm about to say the hell with windows 8 and make a downgrade from the system to an OS that actually works. I had nothing else problems since I bought this computer with windows 8. I don't have time to deal with these questions. It is clear that appropriate testing procedures were followed before the release of Windows 8. Please help, I am very frustrated with all of this.

  I also tried before asking this question. I don't know what happened, or how he did it, but the store has started working when I was on other networks, he didn't always works at home well. I finally download and install windows 8.1 and it fixed the issue together.