Problem with Pioneer DVR-109 driver

Similar Questions

• HP 1350 printer peripheral will not stay in offline mode. Problems with the Wi - Fi driver

  Hi I have a Dell desktop with printer HP 1500 computer.  After printing several documents, the printer has gone offline.  Troubleshooting indicates the problem with the Wi - Fi driver.  The printer is connected to the computer makes a Wi - Fi connection has to do with it?  I have add a portable Wi - Fi system recently.

  Hi, Mt48,

  Is the printer a 1350 aio or deskjet 1500?  You have listed two different models.

  Windows operating system?

  To resolve this problem, perform the following steps:
  1. Right-click on the my computer icon and choose manage, then click Design Manager.
     In the currency Manager there will be the USB root hubs (there may be several USB root hubs) perform the following steps for all root hubs:
  2. Right click on the USB root hub and go to properties, then the power management and uncheck 'Allow the computer to turn off this legacy to save energy' in the Design Manager.

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?lang=en&cc=UK&TaskID=110&prodSeriesId=439153&prodTypeId=18972&ObjectID=c01475742

  Monofunctional and multifunction printers - HP printer is offline message appears on the computer and the HP product does not print

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?objectID=c02221706&lang=en&cc=us&TaskID=130&ContentType=SupportFAQ&prodSeriesId=306884&prodTypeId=18972

  Look for your version of Windows and select printing HP and the Scan Doctor - this is a diagnostic utility

  http://h20000.www2.HP.com/bizsupport/TechSupport/DriverDownload.jsp?prodNameId=306889&lang=en&cc=us&TaskID=135&prodTypeId=18972&prodSeriesId=306884

• I click on "Fix a problem with the NVIDIA graphics driver" and he says: "this solution could not be downloaded.

  I click on solve PC problems (the flag) and it says address a problem with the NVIDIA graphics driver. I click it and it says:

  This solution could not be downloaded

  --------------------------------------------------------------------------------

  The most likely causes:
  Your computer was unable to download the solution at this time. Make sure that your computer is connected to the Internet and then try to download the solution later.

  --------------------------------------------------------------------------------
   
  I am connected to internet, and the works, works etc of web browsing of windows update. Why it is not downloading the solution?

  Download and install the latest driver for your graphics card nVidia.

• My window 7 showing message "a problem with the NVIDIA Graphic driver", but I can't download the solution

  My Windows 7 PC at home keep crashing and I keep losting my screen when I played the game on the last 6 months.  After I restart my PC, it says that there was a screen.   I had since a few Update window update driver and try the NVIDIA drivers with no will.  There were a few times he were message indicating the "resolve a problem with the NVIDIA graphics driver" on the taskbar.  When I click on the message and try to download.  It gives me the message that "your computer was not able to download the solution at this time.  Make sure that your computer is connected to the internet, and then try to download again"that had happen all the time, and of course, I had access to the internet all the time!  I'm getting nowhere for solve this problem.  Can anyone help?  I want to know if there is something I need to know the video driver as usual outside the upgrade.

  PS I tried a lot of stuff, running the troubleshooter from the performance.  I had an i7 with plenty of RAM, running only a few program, hard disk error not... etc.  It seems related to the video driver. I update my window.

  Hello Lewie,

  Thanks for posting your query in Microsoft Community Forum.

  1. What is brand and model your computer?
  2. You did it any significant hardware or change software on the computer before this problem?

  I understand that you lose your screen when you play a game. This happens usually if the installed graphics driver has corrupted or unstable. Therefore, I suggest trying the following methods and check if the problem persists.

  Method 1: Run the tool material and devices

  Try running the next fixit and check whether the problem is resolved.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2: Update your graphics card

  1 open Device Manager by clicking the Start button, click Control Panel, click System and Security, and then, under System, click the Managerof peripheral . If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  2. in the list of hardware categories, find the display adapters and select the device driver you want to update, and then double-click the device name.

  3. Click tab driver , click Update driver, and then follow the instructions. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  For more information, visit the below mentioned link:
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  If you are not able to update the device driver via windows update, you can visit your computer or graphics card manufacturer (NVIDIA) Web site and download & install the latest driver. Or contact the manufacturer of your system to do.

  For reference, you can also consult the following Web page. Click on continue to this site Web (not recommended) if you are prompted for any error of certification.

  A problem of NVIDIA graphic driver

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

• Satellite U500-17F: problems with the new HARD drive

  Hi everyone, I got some troubleshooting with my Satellite and a new drive, I bought recently, because that is already damaged because of too many bad sectors. One is a Western Digital Scorpio Black 320 Bg (WD3200BEKT model number). It should be a fast reader but is not with my Satellite.

  After having mounted the drive in the laptop, I ran a new installation (with full disk format} Windows 7 (64 bit) with all the necessary drivers (that I downloaded directly from the Page of Support Toshiba.)

  The problem is that the laptop needs a lot of time to start and also to disable, and whenever I try to run an application or start a program (for example Firefox, or just a few windows applications), the laptop freezes for about 30 to 60 seconds, the drive no longer works (you can hear leaders put in position 'parking' and the HDD LED control is constant) ", no lights flashing).

  It seems that the drive (during this 30-60 seconds) in something as a stand-by mode. I ran a few Western Digital diagnostic tools and the car looks all right to 100%. It works also without any problems in the other laptop (HP Pavilion DV6500). Could this be a problem with the controller (Intel ICH9M - E ATA AHCI controller) driver?

  Any suggestion?
  Thanx

  Hello

  You use the latest version of the BIOS?
  Please check if you need a BIOS update. Of course I read in a few discussions on the similar question of Win XP you use Win 7 but its value to check the update of the BIOS and U500 series.

  In addition, I recommend check you the power of Windows 7 options.
  Disable in the power profile that you use power saving HDD.

  Just a question:
  You use the option AHCI in the BIOS?
  As far as I know it of possible to use either a compatible SATA AHCI mode.
  AHCI must be used because this option would use full SATA performance.

• Satellite 2770 - problems with Windows 2000 display driver

  Hello

  I have a Toshiba Satellite 2770 and Windows 2000 is installed. If I am wrong the S2770 there graphics S3 Savage IX/MV, and I downloaded the Windows 2000 driver on the S3 site but it wont not be recognized by the hardware detection.

  Then I tried the Windows on the Toshiba site 95SE driver, but Windows 2000 acept used it because it is not suitable for Windows 2000 as it seems.

  What should do? is there a Windows 2000 driver out there that works? I don't want to work at 640 x 480 and 16 colors for ever!

  Hello

  You are absolutely right. Your device has the graphics card S3 Savage IX8 but the problem is that your camera comes with the WinME operating system. This means that there is no support for other operating systems. All drivers are designed separately for each laptop model and the OS. The only way to solve this problem is to install the driver provided by the producer of the graphic card. If this does not work, you have a big problem.

  Sorry, but I don't really know what you can do. Maybe you can try to install the driver designed for Sam 2750. There are the same graphics card, but the driver is designed for Win98SE.

• Equium P200-1ED - have a problem with the installation of driver VGA

  Hello

  I have problem with installing driver vga video, every time in installion on that he stops

  Version: 6,14.10,4833 and it has error poping up...

  Help, please!

  What kind of error?
  Have you installed the chipset utility first?
  What version of Windows XP Home edition, you have installed? SP3 maybe?

• Problem with my Personal Media Drive hd1600

  Hello

  I have a problem with my HD1600 Personal Media Drive.

  After formatting, Windows 7 can not recognize it. Only the power of the blue light is on

  in the Hp website, I can not find the driver software

  Please help me

  Thank you

  As is the case, what I would do then is to format the drive outside of the Windows environment.  I like to use a Linux on CD or GParted on CD.  Unplug your hard drive after the CD and boot from the CD that you did.  With your hard drive disconnected, there is no chance of accitentally choose the wrong drive and the PC will work fine to either that of the CD.  Format the connected USB HD1600 Personal Media Drive everything using one of the version of the Linux CD in the NTFS format.  If it is completed, the disc is OK and you should be good to go.

• Problems with QE65000 and optical driver Océna spectrometer

  Hi, a few months ago, I installed the driver to use the spectrometers of USB4000, HR4000 and QE65000 with LabVIEW 2010 with Windows 7 - x 64. Recently, I measured the spectrum of the Source of Calibration HG - 1 Mercury Argon with the help of software SpectraSuite and a LabVIEW program QE65000 spectrometer ("optical ocean 2000 4000 acquire continuous Waveform.vi, example of library, Fig1"). When I got the two spectra, I observed that there is a shift to the infrared region of the spectrum with LabVIEW program. Acquired calibration coefficients are consistent with "wavelength calibration data" that comes with the spectrometer (Fig2). So, I would like to know if there are problems with the example of the library program or what is the problem?. Attached to this message I send image of obtained spectra.

  The black figure is the spectrum obtained with the example LabVIEW program, including the ocean optical library. The red graph is the spectrum obtained with SpectraSuite and coinciding with the real spectrum of the HG-1 lamp.

  Best regards, Diego

  Version 1.3.2 should be alive in a few hours and this latest version is implementing the changes suggested above.  Did someone mind try these out and let us know how it goes?

  2000 4000 optical ocean pilot Page

  http://sine.NI.com/apps/UTF8/niid_web_display.download_page?p_id_guid=7833BD4A31DA1274E04400144FB7D2...

• IdeaPad Y450 problem with an external hard drive

  Whenever I start to start windows 7, I have to disconnect WD mybook from my laptop each time otherwise it will just pass through the bios screen and then enter halt (black screen with cursor blinking...), if I happen to forget unplug the hd, I just disconnect and then reconnect again when windows 7 starts after that pass this black screen.

  For now, I have a problem with my window of simetimes HD can not see the hd even if the hd mybook bright light flashes, so I think that it might be linked to this old problem that I neglect for 4-5 months

  solutions or suggestions would be really appreciated! Thank you...

  Press f2 to load bios mode and set to factory settings.

  (or just defined order of bios - hard drive - second dvd-...)

• My problem with my cd/dvd drive

  Hi all

  My machine is running XP Professional. My problem is on the CD/DVD drive. In the normal state, when it is empty, it can be opened and closed just as usual. But for most of the CDes DVDes, a problem will occur.
  The problem is firstly that the CD or DVD don't either not read / recognized. Then the CD/DVD drive is no longer available in the my computer window as it is not recognized as well. And also to defrost to manage the list, it is not any element of CD/DVD drive!
  In these situations, whenever I need to reboot the PC once or several times and try to eject the cd drive and off this CD/DVD and restart the machine. Then the drive will come back again!

  How to fix this please?

  This could be a variety of problems. More of how the optical drive is a failure or some form of hardware failure.

  If you're lucky, it's a loose cable or a rider on the CSEL which does not work well.

  You didn't say if it was a drive ATA IDE (PATA) or SATA, so I'll give instructions for both.

  Both:

  Open the computer, unplug and reconnect the cables to the drive and where they enter the computer. This, for the power and data cables. The power is usually permanently secure in power, then only concern on the side of the road.

  If it is an IDE drive, check the jumper blocks. The jumper positions may vary depending on the brand. There is usually a graphic on the disc. If you have configured to use CSEL, change instead to be the master or slave, as appropriate. If you have two chained devices and both are on cable select, rather use the master and slave designations.

  I have not really had a problem with select cable with most of the computers in the past ten years, but it was an old problem that has sometimes created a situation like you described.

  Don't use a jumper for some parameters, and you may need to get a.

  Also if it is an IDE channel, check the connections on the other disk in the chain of disconnect and reconnect.

  Also while you are unplugging cables, use a can of compressed air to blow out the connectors. You should probably take the opportunity to blow in all of your computer as the accumulation of dust can cause problems and a build-up of heat.

  If disconnect and reconnect the cables and making sure that they are explicitly does help together as master or slave discs (master/slave is IDE only), try replacing the cable (SATA or IDE) data. Also if you have a free power cable, try swapping one in the player doesn't do not. It is rare, but it could be the problem.

  In addition, you should try to get a cd player, kit cleaning and cleaning the disc. Usually regardless of if the kit says its for a cd player, a dvd player or a computer.

  If none of this helps, the drive is probably a failure and you're S.O.L. I suggested swapping the cables first because a new cable is $ 5 - $10 while a new drive starts at $50. Also, you can usually pull a cable from a computer that you have retired (a good idea to get some spare since a broken computer parts before getting rid of it. If the hard drive was not the problem, you can use it as additional storage for the new computer. The optical drive can give you two in your new computer. The cables are spares for cases like this. Heck, don't throw up until you have two generations of dead computers, collecting dust. Keep the old as spare parts).

  Sorry, but I don't see a lot of other things that can help in addition to clean the disk, control & clean the cable connections and check jumpers (if IDE).

  Oh, one last thing.

  Log in as an administrator and check the Device Manager. Check if the drivers have been updated whenever recently since around the time you started to get into trouble. If so, roll back the driver.

  https://support.Microsoft.com/kb/283657?WA=wsignin1.0

• Problem with network controller / wireless driver

  Hello, I have problems with my computer network controller. I can't connet to the Internet wireless or wired. In addition, two of my USB Ports do not work.

  My system is HP Pavilion G4 - 2235dx

  A6 - 4400M with Radeon AMD

  Windows 7 Professional

  The hardware ID

  PCI\VEN_168C & DEV_0032 & SUBSYS_1838103C & REV_01

  PCI\VEN_168C & DEV_0032 & SUBSYS_1838103C

  PCI\VEN_168C & DEV_0032 & CC_028000

  PCI\VEN_168C & DEV_0032 & CC_0280

  There are other issues such as:

  PCI device

  SM Bus controller

  USB controller

  When you open Device Manager and every thing under "Other devices" are not available, you will get the real picture. Please I need your help to make this work again.

  Thank you.                       David

  Hi, David:

  Here are links to the drivers you need:

  1. first install the amd chipset driver and restart. You only want to use the first file on the Web page.

  This will install the smbus and usb3 controllers.

  http://support.AMD.com/en-us/download/chipset?OS=Windows 7-64

  2. wireless card driver is the following:

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5229464&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_118499_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  3 PCI device is the following:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-103762-1&cc=us&DLC=en&LC=en&OS=4063&product=5275619&sw_lang=

• X230T USB 3 port sleep problem with external Blu - Ray drive

  Hi all

  I bought a new LG external blu - ray drive and I have problems with it sleeps very quickly.  It is recognized in Windows 7 and will be available for a short period of time after I turn it on, but if I don't use it for 30 seconds, it's in a kind of fashion 'sleep'.  It works perfectly on the single WE port 2.0 on the X230T so there must be something with the 3.0 port.  The drive is powered by an AC adapter and USB 3.0 cable included one.

  I tried to disable all the properties sleeping USB in all areas of power management and power options in Windows.  Also enabled and disabled USB hub root energy saving.  Also, I went through the BIOS and threw the USB options as well and can't find why it is go to sleep so quickly.  I have the latest firmware on the drive, as well as the latest drivers Lenovo USB 3.0 for the X230T.

  I guess I'm out of luck at this point because I think I've tried all possible solutions?

  Thank you.

  Hi again,

  I have looked on the specs and do not see why this problem should occur. I would make sure that the BIOS is updated, if you have not already. The latest BIOS for your machine is 2.03 and came out a month ago. This update, you can find here. And if this does not work, can you check and publish what are the settings in your BIOS Config > USB Configuration?

  Best,

  Adam

• Problem with USB 2.0 Driver

  I'm having a problem with the USB 2.0 driver. Whenever I connect my USB drive, I get a notification of an unknown device and I also used the troubleshooter to solve problems, but he said-

  An unexpected error has occurred. The Troubleshooting Wizard can not continue.

  Identifier of the package: DeviceCenterDiagnostic

  Path: unknown

  Error code: 0 x 80070002

  Source: engine

  User: Chinmaya-PC\Chinmaya

  Background: high

  Every time that I find this error code while troubleshooting the USB 2.0 driver. I even tried reinstalling the driver, but it's the same thing over and over again. I also tried to install Microsoft Fix it, but it won't install, it says "Microsoft Automated Troubleshooting Services BootStrapp has stopped working". Someone at - it this same error? I can't even connect a USB on my computer because of this error.

  If anyone has an answer, I would be very happy to know.

  Hello Chinmaya,

  Thank you for the update on the issue.

  Before any change in the registry, I highly recommend you back up the registry. You can see How to backup and restore the registry in Windows as described in the previous answer.

  UpperFilters and the LowerFilters are assigned values in registry keys. Upper filter drivers go between the operating system and the principal driver, and the lower filter drivers between the driver and the hardware.

  You can try the suggestion and let us know the result, we will be happy to help you.

  Thank you.

• problem with TSSTcorp DVD +-RW Drive SN - 208BB driver

  Hi I have a laptop Inspiron Windows 8, only about a month and the DVD continued to show.  I put a cd or dvd and shows nothing.  He makes noises but doesn't show anything.  I ran a material and problem solving devices and it says there is a problem with the above drive and the USB-drive IF port.  I select apply this fix, but it says it can't be fixed and the driver must be reinstalled.

  Ive tried to find this driver on the dell website, and I can't seem to find it.  I think it's a Toshiba product but am really stuck now.  Can anyone help? :(

  Hmm, well I went into Device Manager, uninstalled and it did something and came back!  I tried the same thing with the USB driver, I had trouble with, but who did not return :/  Hmmmm...