Problem with the Sony ARW in CS2 files

Similar Questions

• problem with the backup data in text file

  Hello

  The problem I am facing wihile, saving the data in the text file is that everytime when I'm slecting the path of the façade, data that are recorded are added with the previous data, not only in the new text, the new data set is saved but also, is there any previuos run for the program , the corresponding data is also present in this text file.

  However, when I change the same ''(file path) to 'constant' in the control block diagram, and then add the path of the file, it doesn't have this problem. Basically, changing the "file path" constant in the diagram of control block (so that it is displayed in the front panel) is at the origin of the problem.

  Help, please!

  Thank you

  Your shift on the loop Register For is not initialized. It will keep the value of the string since the last time that he performed. That initialize and it should solve your problem.

• Problem with the Sony Bravia KLV-32T550A color

  My Sony Bravia KLV-32T550A (Serial No. 6165091) which is about one and a half years began to have problems with color. When you turn it on, it turns red and then the colors are all stripped top and blurred. After now for a few minutes, the color is back to normal, and then it goes bad again after a few minutes. An authorized Sony technician came to my place and told me immediately that this is a problem with B motherboard and it must be replaced costing me about 5500 rupees as well as Service charges. Please indicate if the technician diagnosed the problem correctly and this card cannot be fixed first to solve this problem of color instead of such a costly replacement.

  Thank you for your message and welcome discussion of the user forums.
  According to the description of your problem, the B-board (motherboard) is normally the root cause of the problem.

• Problems with the 'Association' in Windows 7 files

  Original title: constantly stuck in insane mode, 'Open with' file associations opens instead of the selected despite the default application

  Some types of files, mainly media, refuse to open with an application and still shows the "Open with" dialog. The option "Always use the selected program to open this kind of file" is available and verified, but makes no difference. The next time I try to open it, I get the same dialogue again. This is my original problem.

  The programs I am trying these to are foobar2000 (for audio) and Media Player Classic (for video files), respectively.
  I tried many suggestions, most involving the registry, who only managed to make things worse. At present, the file associations are generally uninterrupted again (I went through a phase, where not even Explorer would start over), but there are a few things left that are quite strange.
  For example, for file extensions that work (open their associated program by double clicking), the context default "Open" menu item is normally "BOLD". For me, it is no more.
  Also, I normally do not use Windows Media Player. Therefore, I usually don't bother with going through the initial report set up the wizard who wants to activate the automatic recovery of the DRM keys and stuff like that. To try to solve this problem, I only skip the wizard and now all the files THAT WMP wants to associate are permanently associated with it, and double clicking for example a WAV files directly open WMP without going through the "Open with" dialog. However, when I go to the control panel applet "default programs", I find myself unable to uncheck WMP associations or partner with another application with them.
  I can't go to the association of foobar2000 (my audio player of choice) and file associations "Select all", then "Save". And behold, when I return to registration after registration, it is empty again (this program a default 124 0).
  Now as the mucking with the registry seems to be the way to go about these things, as evidenced by most of the advice on the internet, as well as on this site, I decided to test a theory. In HKEY_CLASSES_ROOT for all types of file WMP STOLE, the (default) value was WMP11Assoc.Something. I decided to change these values to their equivalent of type foobar2000 (such as foobar2000. MP3) and Hello! Suddenly, foobar2000 has "29 of 124 by default". Surely, which should count for something.
  Nope. Opening one of the 29 file types where I applied this change is that open dialogue 'Open with' once again. At least he didn't open WMP, I thank Bob for this. But again, we're back to square one. The initial problem.
  Now, in an interesting case study, I invented a new type of file on the spot, which was not used for anything else. In this case, I used '.lam '. I made an empty file with this extension and set to open in Notepad. This works. But where it gets interesting is when I try to change the association then. I opened the menu popup and select 'Open with' and (arbitrarily) has decided to open it with 7 - zip, check "always use the selected program to open this type of file". But the next time I opened it, it is still open in Notepad! Closer to the irrefutable, I searched for the novel file extension using Regedit. The results of three who came were in the following keys:
  HKEY_CURRENT_USER\Software\Classes\. Lam
  HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\FileExts\. Lam
  HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\RecentDocs\. Lam
  The first linking lam_auto_file. I deleted all three keys and the key lam_auto_file. After refreshing the Explorer, I could choose a different association, and it's stuck
  ! This is a solution for the types of files that are not normally associate with something else.
  However, when I tried this same technique with .mp3 (noting that the association who is system wide and therefore in HKEY_CLASSES_ROOT instead of HKEY_CURRENT_USER\Software\Classes), delete all the keys and associations, when I try to associate it with something, it won't be yet to stick. Subsequent attempts to open the file still pop up the "Open with" dialog
  Normally, I can find a solution to almost any problem, an extensive search on Google, either by launching logic mixed with trial and error to her. It left me speechless. Someone has ideas, outside the usual "have you tried it turning on and off again", "have you tried super registry cleaner ultimate Xtreme ($500)", "delete system32", "Reinstall", "you have a virus", etc.. ?

  Hello

  A sound solution suggests allows you to perform the following method.

  Method 1: use this option to choose which programs you want Windows to use, by default.

  If a program does not appear in the list, you can make the default program using set Associations.

  1. open default programs by clicking the Start button, click default programs.

  2. click on associate a type of file or Protocol with a program.

  3. click on the file type or protocol that you want the program to act as the default value.

  4. click on the program of change.

  5. click on the program that you want to use by default for the selected file type, or click the arrow next to

  Other programs to show other programs. (If you don't see your program, or other programs
  is not listed,

  Click Browse to find the program that you want to use and then click Open

  6. click on OK

  For more details follow the link below:

  http://Windows.Microsoft.com/en-us/Windows7/change-which-programs-Windows-uses-by-default

  Method 2: try to create a new user account and check if you have the same problem.

  To create a user account

  1. to open user accounts, click the Start button, select Control Panel, click on accounts of users and parental controlsand then click user accounts.

  2. click on Manage another account. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  3. click on create a new account.

  4 type the name that you want to assign to the user account, click an account type, and then click create an account.

  For more information follow the link below:

  http://Windows.Microsoft.com/en-us/Windows7/create-a-user-account

  If everything works well in the new user account, then the user account may be damaged.

  To fix the damaged user profile, you can check the link below:

  http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile

• problems with the external table to excel file

  Hi all
  I tried to use the statement below to create an external table.this table refers to an excel file.
  
  CREATE TABLE EMPFRAUD_TEST
  (
  SERIAL_NUM WHICH VARCHAR2 (10 BYTE),
  BRANCH_CODE VARCHAR2 (10 BYTE),
  BUSINESS_ADD VARCHAR2 (100 BYTE),
  VARCHAR2 (50 BYTE) REGION,
  DATE OF TRANSACTION_DATE_TIME,
  DATE OF REPORT_DATE_TIME,
  NO_OF_TRANS VARCHAR2 (4 BYTE),
  NUMBER OF AMOUNT,
  FRAUD_TYPE VARCHAR2 (25 BYTE),
  IMPACT_CATEGORY VARCHAR2 (10 BYTE)
  )
  EXTERNAL ORGANIZATION
  (TYPE ORACLE_LOADER
  THE DEFAULT DIRECTORY EXT_EMP_TEST
  ACCESS SETTINGS
  (records delimited by newline
  BadFile "empfraud%a.bad."
  logfile "empfraud%a.log".
  fields completed by «,»
  surrounded of possibly ' "'lrtrim"
  missing field values are null
  )
  LOCATION ("fraud.csv")
  )
  REJECT LIMIT UNLIMITED
  NOPARALLEL
  NOMONITORING;
  
  the problem is the following
  (1) when I run the query above the table will be created,
  but when I try to select in the table, an empty table display.
  When I checked the error log file, the following message was given.
  It was obtained from an oracle on unix Server database.
  
  'L_NUM '.
  KUP-04036: second enclosing delimiter not found
  KUP-04101: Save 71 rejected in the /home/oracle/ext_folder_test/fraud.csv file
  KUP-04021: field error for the field formatting ACCOUNT_KEY
  KUP-04036: second enclosing delimiter not found
  KUP-04101: Save 79 rejected in the /home/oracle/ext_folder_test/fraud.csv file
  KUP-04021: field formatting of error for the serial_num field which
  KUP-04036: second enclosing delimiter not found
  KUP-04101: Save 80 rejected in the /home/oracle/ext_folder_test/fraud.csv file
  column in treatment of TRANSACTION_DATE_TIME error in the row 1 for the /home/oracle/ext_folder_test/fraud.csv data file
  ORA-01858: a non-digit character was found here where was waiting for a digital
  column in treatment of TRANSACTION_DATE_TIME error in line 2 to the /home/oracle/ext_folder_test/fraud.csv data file
  ORA-01843: not one month valid
  column in treatment of TRANSACTION_DATE_TIME error on line 3 for the /home/oracle/ext_folder_test/fraud.csv data file
  ORA-01843: not one month valid
  column in treatment of TRANSACTION_DATE_TIME error in row 8 for the /home/oracle/ext_folder_test/fraud.csv data file
  ORA-01843: not one month valid
  column in treatment of TRANSACTION_DATE_TIME error in line 9 to the /home/oracle/ext_folder_test/fraud.csv data file
  ORA-01843: not one month valid
  column in treatment of TRANSACTION_DATE_TIME error in line 10 by /home/oracle/ext_folder_test/fraud.csv data file
  ORA-01843: not one month valid
  column in treatment of TRANSACTION_DATE_TIME error at line 11 to the /home/oracle/ext_folder_test/fraud.csv data file
  ORA-01858: a non-digit character was found here where was waiting for a digital
  column in treatment of TRANSACTION_DATE_TIME error in line 12 to the /home/oracle/ext_folder_test/fraud.csv data file
  ORA-01843: not one month valid
  column in treatment of TRANSACTION_DATE_TIME error in the 13th for the /home/oracle/ext_folder_test/fraud.csv data file row
  ORA-01843: not one month valid
  column in treatment of TRANSACTION_DATE_TIME error in line 14 to the /home/oracle/ext_folder_test/fraud.csv data file
  ORA-01843: not one month valid
  column in treatment of TRANSACTION_DATE_TIME error in row 15 for the /home/oracle/ext_folder_test/fraud.csv data file
  "ORA-01843: not one month valid."
  
  
  pls I need help to fix it fast
  Thank you
  
  concerning
  Abdulrahman olayide arpin
  
  NB:
  After the conversion to .csv format.
  HERE IS THE DATA THAT I'M TRYING TO ACCESS THE EXCEL FILE
  
  REGIONS, Transaction_Date_Time, Report_Date_Time, Account_Key (account number), BUSINESS OFFICE, Number_of_Transactions, Total_Amount (N)
  Ojo 1,162,9 Street, South of Lagos, various, 17 January 00, CHECK
  2,0238, "10 cyril Road, Enugu", Orient, 21/06/2006,23/12/10,020968765357 09867653920174,1,20000000
  3,0127, '261, Roland Rd, Asaba', Midwest, 22/12/2010,23/12/10, 1,'00160030006149, 6000000
  4,0519, 'just road, Onitsha.
  ', East, 12/03/2010,14/02/11,0896002416575,1,5000000.
  5,0519, 'just road, Onitsha.
  ", Orient, 03/12/2010,14/02/11,06437890134356,1,5000000.
  6 149, rue olayide, South NGN01492501036 of Lagos, 10/02/2010,17/02/11, 1,6108950
  7,0066, wale, mi - west,18/02/2011,18/02/10,'05590020002924,1,55157977.53
  8.66, john, Mid-west, 6787500, 1,'00660680054177 11/03/2010,14/03/09
  Waheed 9,0273, Biem, N/central, Jan 09 Dec/2010,01/04/11, Nile, 1, 14146040
  

• DNS problem with the fake IP on computer file discovered. Help

  installed a new Virus program (Kaspery switched to Norton) and impossible DNS verified or recognized.  When the IP address has finally found (ARIN) it was not related to my machine, but to another in another city, somewhere else.  How is that possible? -is that my spyprogramming is not able to clear a hijacking, a bot or a virus, or is there another explanation maybe the FBI cyber crime unit should enlighten us on? have you ever heard such a thing, a product of MS?

  Your message is in the forum for people needing help with the anti-malware program from Microsoft Security Essentials (MSE).

  Since your "glitch" appeared after having uninstalled Kaspersky and installed Norton, suggest that your question should be considered by the Norton Support.

  You could try: http://community.norton.com/

  You may also find useful information by reading the Kosh Vorlon response in the following thread: http://answers.microsoft.com/en-us/protect/forum/protect_scanning/identifying-computer-ip-addresses/0b3d14f6-979c-4053-a74b-845f2e8b0d15

• Problems with the one backup. MSWMM file to. WMV

  I get the error "cannot complete film Assistant record" when you try to save a. MSWMM file to. WMV. any ideas? It starts to save the file, and then after a few minutes, I get the error. A lot of space on the hard disk.

  O, I just used first place. I think the source files were too big (100 MB) so the final product was too big for WMM to manage. Thanks in any case! xDDD

• problem with the LR 5 cannot read the RAW of Sony A7R II files

  I have a problem with the LR 5 cannot read the Sony A7R II RAW file

  Hi alexl

  Greetings!

  Support for this camera is added in Lightroom version 6/CC

  

  Your Options are either update of Lightroom CC/6 or Free DNG Converter allows to convert .raw .dng files.

  This way you can import into Lightroom and can work on it.

  Download link for DNG Converter:- Adobe - Adobe Camera Raw and DNG Converter: for Windows: Adobe DNG Converter 9.2

  Adobe - Adobe Camera Raw and DNG Converter: for Macintosh: Adobe DNG Converter 9.2

  Concerning

  ~ Assani

• I have a problem with the touch screen of Sony.

  Original title: "Sony touchscreen issues."

  I am running Windows 7 Home Premium on a Sony All In One with touchscreen. For about 4 weeks, I got a problem with weird things happening on the screen. For example, I can use any application and it will automatically become minimized and I'm now looking at the level of the office. Other times on keyboard screen will appear in itself. Do not know what is happening, but it sure is frustrating the heck out of me. Answer from Sony is that I put the computer back to factory settings, thus losing my files and programs. Is there a way I can back up the system and retrieve my programs from the backup. I don't know if I can find my original downloads, including Office 2010.

  Thanks a lot for your help.

  Dennis

  Hello

  IAM having the same problem with my Sony all in one touch with Windows 7 home Premium edition running, did you get your problem solved, please let me know what I need to fix, it is very annoying to use the computer now that the application itself minimizes every minute.

  Help, please

  -Irshad

• I'm having a problem with the FireFox browser. I have attached two files that describe the problem. I have marked their A & B. A is the way it should lo

  I'm having a problem with the FireFox browser. I have attached two files that describe the problem. I have marked their A & B. A is how it should look like and B what happens once I have, I opened several tabs. I can get it back to normal if I click VIEW, click Customize. When the window customize appears that Firefox returns to its normal state. I have to click on the done button and go back to what I did. I tried to reset FireFox back to the default settings, but that has not fixed the problem.
  It started happening a month. Is there a way I can fix this? Thanks for your help. I don't know how to fix my 2 attachments that shows the problem I'm having.
  [email address removed to protect your privacy and security]

  Try disabling hardware acceleration in Firefox.

  • Tools > Options > advanced > General > Browsing: "use hardware acceleration when available.
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• problem with the Finder - files and folders displaying incorrectly

  After acquiring a new iMac, I noticed a problem with the Finder - files and folders are displayed wrong (see table).

  This is what happens always after the files have been transferred from one folder to another. I was reminded of my days of using Mac OS in the 1980s when automatic setting of files was not so "automatic." I use Mac OS for decades and I don't remember the last time I had to think about GUI problems like that.

  Other problems in the graphical display of files and folders were introduced, such as when you have hundreds of files in a single folder, you end up deleting about 30 to 40 of them say in a particular section, and you end up with gaps of the ChartSpace where files used to be, that is the remaining files automatically rearrange themselves (fill in these gaps) - never. A week later, you open the folder, and the gap of GUI is still there.

  I decided to do a clean install of the operating system but nothing works.

  Is there some setting in Prefs I'm missing?

  

  Hi there highland99,

  Looks like your folder icons are not accommodating themselves automatically you plan to do. To me, this indicates that you have organize by the None value in the view menu. You can change the way files and folders are prepared automatically by clicking on view > reorganize by and selecting how you would like that fixed.

  Thank you for using communities of Apple Support.

• How to do this: Photoviewer, Windows cannot save changes to the image due to a problem with the properties of the file!

  Hi, I'm trying to post a photo, but whenever I have try rotation to the right, it says something like: can't save changes to the image due to a problem with the properties of the file. My laptop is MS, but the photos were taken on the Iphone. How to do this?

  I don't know if the following links answer your question, but
  they may be worth a visit:

  Good luck and * proceed at your own risk *.

  FWIW... There is a very long discussion (several pages) to the
  following link:

  Cannot change the imported iPhone 4S photo
  https://discussions.Apple.com/thread/3444951?start=0&TSTART=0

  More Discussion

  iPhone 4S image properties is not compartible with Windows?
  Editing can be done on the computer due to the error
  "Windows Photo Viewer cannot save changes to this picture.
  because there is a problem with the properties of the image file".
  Any help?
  https://discussions.Apple.com/message/17291884#17291884

  More Discussion:

  We cannot turn a few photos in Windows 7 (but can turn others)
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-pictures/cant-rotate-some-photos-in-Windows-7-but-can/3a809845-9144-4BB1-9bb3-ab4f5b856524

  A simple solution is to open the photos in paint or most other
  digital image editor and modify it.

  Some people have reported success using the following free download
  to remove the metadata.

  Property restrictions stripper iphone 4S (JPEG & PNG Stripper)
  http://www.SteelBytes.com/?mid=30&cmd=download&PID=15

  Here's a way to turn...

  Easily turn locked iPhone 4 and 4 s Photos in Windows 7 with
  the rotator Lossless JPEG free
  http://www.daleisphere.com/easily-rotate-locked-iPhone-4-and-4S-photos-in-Windows-7-with-the-free-JPEG-lossless-Rotator/

  Free download JPEG Lossless rotating
  http://annystudio.com/software/jpeglosslessrotator/

• Problem with the executable files

  Hello all, I need a help from you...

  I use LV 2009 SP1 Professional Development Suite on Windows Seven and I have a problem with the executable files, a problem that I have ever found with other versions of LV (8.x, for example) and I'm a little surprised...

  In the attachment you will find an example of what I mean.

  There are two base screws, the main one (prova) and a Subvi (provasubvi). The main vi launches the Subvi and the Subvi simply create a chart. As you can see on the screws works fine, without any kind of problem.

  I also created the exe file, without specifying that no particular option... and 'magic' of the application does not work as I want. In particular, it seems that the Subvi is running, but the front panel will not be accessible.

  I also try to play with the Subvi construction structure and options, but nothing change.

  Did you ever solve something like that?... I would say that I thank you in advance for any suggestion...

  Andrea

  Hello andrea,.

  Looking at your project I've heard that you do not include the Subvi during the build of the project. SO I slightly modified. Please find the attachments.

  Thank you and best regards,

  srikrishnaNF

• I ran CHKDSK, the report tells me I have problems with the file system, usn journal. ___

  I ran CHKDSK, the report tells me that I have problems with the sys file. I ran CHKDSK/F, it is said it fixed the problem but I ran CHKDSK again and it shows that the same listed the issues.

  Describe how you run chkdsk.

  That is what the report said: you have problems with the sys file?

  CHKDSK examines the disk space and use of the disk for the table of allocation of files (FAT) and NTFS file systems. CHKDSK provides information specific to each file system in a situation report. The report shows the errors found in the file system. If you run chkdsk without the /f on an active partition command line option, it can report errors because it cannot lock the drive. You should use chkdsk occasionally on each disk to check for errors.

  If you run chkdsk from a command prompt while Windows is running, it can report errors or it may not report errors - and it may report different
  Errors each time you run.  If this is the case, it could just be the way you run chkdsk.

  Here's how Microsoft explains this observation:

  "... CHKDSK may report that the disc is damaged, even when there is no
  current real corruption. This can happen if NTFS happens to modify
  areas of the disc on behalf of some programme activities that CHKDSK is
  review at the same time. To check a volume correctly, the volume
  must be in a static state, and the only way to ensure that the State is
  to lock the volume. CHKDSK only locks the volume when /F or/r (which
  involves the 'F') is specified. For example, you may need to run CHKDSK more than
  time so that it can complete all the steps in read-only mode. »

  If you run chkdsk from a command prompt, you are not the necessary static state and you can encounter errors "when no real corruption is present. This is how it works when you use this way.  Any changes made to a NTFS file system modifies the USN Journal.  If you are not in a static state, your USN change Journal probably all the time, so what you see (says something like that) can be quite normal.

  Two ways to ensure that you are in a static state is to run chkdsk from the Recovery Console or to schedule a chkdsk to run the next time that the system
  Restart by answering Yes to the question:

  Would you want to check this volume to be the next time the system restarts?

  If chkdsk reports errors when running in a static state, the errors should be investigated, resolved or explained.  This may take several
  chkdsk runs all of the issues and some problems cannot be resolved by chkdsk.

  If chkdsk runs the next time the system is restarted, the activity and the result will be displayed in the application event log.  Look in the Application log for
  Winlogon events and a source have the date and the duration nearby time chkdsk.

  It is in fact a chkdsk additional reading if you want to learn about it and it will explain everything you see and why your expectations exceed reality.

  Please vote my posts as helpful so I can get a lot of points. I'm saving for a pony!

• Windows Media Player cannot play the file because there is a problem with the audio device.

  Original title: Media Player

  I tried to play my music in media player and they will not play. The tab that appears says "Windows Media Player cannot play the file because there is a problem with the audio device. It might not be a sound device installed on your computer, it can be used by another program, or it may not work properly. Also, I can not play music in the window, that I downloaded everything. If anyone has an answer I would appreciate the help. Thank you

  Hi MikeMcKayXE,

  ·         What is the brand and model of the computer?

  Follow the suggestions below for a possible solution:

  Method 1: Quit other programs that may be using your sound device, and then try to play the file again.

  Method 2: Install an updated driver.

  Step 1: Firstly uninstall the audio from the device manager driver and Add / Remove Programs

  a. click Startand then click Control Panel.

  b. click Systemand click on the hardware tab, then click Device Manager.

  c. to the title sound, video and games controller, check the sound card that is listed.

  d. right click on the sound card, and then click Uninstall driver.

  Step 2: To see if an updated driver is available, use Windows Update or access the sound device manufacturer's Web site.

  Follow these steps to do the same thing:

  a. click Startand then click Control Panel.

  b. click Systemand click on the hardware tab, then click Device Manager.

  c. the title sound, the video controller and games, make sure that the sound card is listed.

  d. right click on the sound card and then click Update driver to install the latest version of the driver.

  e. visit the sound card manufacturer's Web site to determine if a newer version of the driver is available for download.

  Method 3: If you have multiple audio devices installed on your computer, try to use another. The selected audio device might not support Secure Audio Path (SAP).

  You can see the following article for more information:

  Resolution of the problems of reading in the Windows Media Player for Windows XP

  http://support.Microsoft.com/kb/306317

  Let us know if that helps.