Problem with TouchPad-Help!
I have a new Toshiba Sattelite with Windows 7. All of a sudden my touchpad has stopped working. I went to the device in my control panel and it says that the device is functioning properly. Anyone have any ideas on how to solve this problem? I have a USB mouse that works very well.
Thank you!
Hello
Toshiba has also map of keys which allow easy adjustment of the TouchPad. See support for Toshiba
and Forums. The key shortcut for the TouchPad, if they are responsible in the Fn + F9 or see the key card
So usually loaded at the top of the screen.
There is also usually a TouchPad control utility that loads in the Notification area next to the clock
at the bottom right.
Toshiba support - click Communcate for links to the Forums and Contact Toshiba.
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp
Toshiba downloads - access your model.
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp?NAV=download
Toshiba forums - good source of info from others who have the same system or similar
http://laptopforums.Toshiba.com/
Check with the manufacturer of system support, documentation in line, or forums as there probably
are shortcut keys that enable and disable the touchpad functions.
Also check the control - Mouse - touchpad settings panel.
You can also try this:
Panel of configuration manager devices - mouse and pointing devices - Double click on the touch pad-
The driver tab - click on Update Driver (which is may not make anything like MS is far behind certifying)
(drivers), now right CLICK on the touchpad and UNINSTALL.
Then go to the USB and UNINSTALL ALL controllers except the category itself (all in).
RESET
This will refresh the driver for the TouchPad and battery USB. This does not prevent the touchpad
of work.
Here is the similar procedure in XP, Vista is the same, except that we need to clear the specific
device if present.
http://support.Microsoft.com/kb/310575
Then go to the website of the manufacturer of system (Toshiba downloads - access your model - listed above)
and get the latest touchpad drivers.
Download - SAVE - go to where you put it-click on - RUN AS ADMIN.
I hope this helps.
Rob Brown - Microsoft MVP - Windows Expert - consumer: bike - Mark Twain said it right.
Tags: Windows
Similar Questions
-
Having problems with the help of web camera program does not work when I click it. don't know what to do. Please help thanks.
Hello
Right click on the shortcut tab icon - properties - look on the target line to see where and what type of program
is supposed to work.You will probably need to reload the drivers of the device and any camera control software.
Login as an administrator.
Double-click Control Panel / Device Manager - Imaging - writing down of the brand and model of camera.
on this subject and on the tab of the driver is version. Now, click on update drivers (who are unable to do anything as MS
is far behind the pilots of certification). RIGHT click on the camera - UNINSTALL - REBOOT - it
will update the driver stack.Now, go to the system manufacturer's website and download the latest driver for the camera and the other related camera
software (if not more recent get the same).Download - SAVE - go to them and RIGHT CLICK - RUN AS ADMIN - reboot after each driver.
Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlThen let windows updates on however prevent loading of drivers who are often older than the
those that you have installed. If updates suggests a pilot and then HIDE it and watch manually to see if their
really is a more recent version (at the time system manufacturer and the sites of the manufacturer of the device).How to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspxI hope this helps.
Rob - bicycle - Mark Twain said it is good. -
problem with the help of the conditional formatting on a cell that is defined as the percentage
Hi all
I am facing a problem with the help of the conditional formatting on a cell that is defined as the percentage.
I am using beaches for example:
is equal to or greater than 10% - green color
5%-10%-yellow
less than or equal to 5%-color red
the problem is that keeps the value 10% get yellow color when it should get green.
i thought that is a rounding issue but when I change the definitions of the cell to learn more decimal places I see this part of the percentage 9.65% and some of them are 10.00% and they are both colored in yellow.
I also tried to change the way range of 6 to 9%, but values between 9.65% or 5.5% are not colored.
I really enjoy your help!
You know the reason and the solution.
change the format of the column and go or add a column more with decimal and opt for conditional and hide report.
Thank you
-
Hello!
I m facing a problem with the help of oraext: query-database.
In my transformation im try the following (Simplified):
How to get the correct value when you use oraext:query - database?<xsl:template match="*"> <xsl:variable sqlQuery="select ....."/> <xsl:variable name="storeSec" select="oraext:query-database($sqlQuery,true(),true(),'jdbc/xref')/> <xsl:choose> <xsl:when test="string-length($storeSec/ROWSET/ROW[1]/STORE_PART_SECTION) > 0"> <xsl:value-of select="$storeSec/ROWSET/ROW[1]/STORE_PART_SECTION"/> </xsl:when> <xsl:otherwise> <xsl:value-of select"some other val"/> </xsl:otherwise> </xsl:choose> </xsl:template> {code} This always results in +some+ +other+ +val+ !! I´v checked the output from oraext:query-database by using getcontentAsString and if I instead test putting the expected output from oraext:queryDatabase in my variable it gives me A100 which is what i expected. {code} <xsl:template match="*"> <xsl:variable sqlQuery=select ....."/> <xsl:variable name="storeSec"> <ROWSET> <ROW num="1"> <STORE_PART_SECTION>A100</STORE_PART_SECTION> </ROW> <ROW num="2"> <STORE_PART_SECTION>XXm</STORE_PART_SECTION> </ROW> </ROWSET> </xsl:variable> <xsl:choose> <xsl:when test="string-length($storeSec/ROWSET/ROW[1]/STORE_PART_SECTION) > 0"> <xsl:value-of select="$storeSec/ROWSET/ROW[1]/STORE_PART_SECTION"/> </xsl:when> <xsl:otherwise> <xsl:value-of select"some other val"/> </xsl:otherwise> </xsl:choose> </xsl:template>
How should you exit? Several item ID with each having a value of the result set?
If Yes, then you can try following: -
I have a problem with the help of the touchpad.
Original title: cannot zoom with touchpad etc.
Cannot set my pad touch, tempted several times.
Hello Shelly,Please go to the Microsoft Community Forums.Description of the question, we understand that the touchpad is not working properly?Let us move forward and help the issue.If you could answer a few questions that would help us resolve this problem:1 have you tried to install the touchpad of the website of the manufacturer drivers?2. What is the exact problem you are facing with touchpad?3. don't you make changes to the computer before the show?We invite you to check out the link and follow the steps in the article:Mouse, touchpad and keyboard with Windows problemsI hope this helps. If you have any other queries/issues related to Windows, write us and we will be happy to help you further.
-
Satellite Pro C660 - on and off the problem with Touchpad
Hey guys,.
I had one on and out of the question with my touchpad at least a few months now. I tried to do the function + F9 thing with little effect. Also, I re-uploaded the synaptics driver, which seems to make it work for a little while but then it started working sporadically.
Currently my touchpad works from time to time, if it fails on the first pressing Ctrl Alt Del and then Esc seems to do the job for a little long but after that it just stops working. I am a student and not having is not a fully functional laptop is often a major obstacle if any help would be great.
Best,
gleeful199
Hello
My first question is: When did you notice this problem from touchpad.
I mean, the Sat Pro C660 is a portable old and if this issue seemed to be in the first day of purchase, then something touched the touchpad feature in the past.
The question is: is at - it something wrong with the software or touchpad maybe module.
I think that can be answered only the settings of the notebook back to factory State.
If you are recovering the using laptop computer Toshiba recover disk, you will get exactly the same State as at the first day of the purchase.If the touchpad would not always work properly, well there is some hardware problem
-
Satellite M70-309 - problem with touchpad
Hello
I have a problem with the touchpad of my laptop. When the laptop is charging, touchpad not working properly but if I unplug it work.
What is the problem? I don't understand...
I thank.
Hmm when did you notice this problem?
Since the first day of purchase?I'm not very well if it could be a software problem, but of course, you could try to update the driver for the touchpad to ensure that this problem related isn t touchpad driver m.
If the driver update help doesn t then a hardware problem may be possible
It is hard to say what role might be affected but a laptop computer technician could run tests and might be able to tell what's wrong. -
ENVY dv6-7320el: problems with touchpad
Hello
I'm new here, so I don't know if this is the right place for this question, but here goes:
I had problems with my touchpad, precisely with the two-finger-roll. It would sometimes stop working, but then set a few minutes. Today that work completely collapsed. I have read suggestions on how to solve this problem, I tried the HARD RESET, it did not help, I tried to juggle synaptics in Panel, which did not help either. Now, I have managed to completely remove the synaptics and cannot install it back.
Can someone please help? The two-finger-roll was my main way of getting around, I feel so lost without her.
model: dv6-7320el
Thank you!
Bob
Dear customer,
Welcome and thanks for posting your question on the Forum of Support HP
Looks like you are facing difficulties to solve problems with your laptop Touchpad
We will surely help you with this
Steps to drain the static charge and load the BIOS default settings to solve the problem
Step 01. Turn off the laptop
Step 02. Disconnect the power/AC adapter and also remove the battery too
Step 03. Press and hold the power button of the laptop for a minute
Step 04. Now re - insert the battery back in and plug again the power supply/adapter
Step 05. Start Notepad and keep pressing the F10 key during startup to access the BIOS
Step 06. Once you get the BIOS, please press F5 or F9 key to load the default settings for the BIOS
Step 07. Now press ESC/ESC. Save Changes and Exit - Yes
Step 08. Now, please wait until the unit load the Windows operating system
Now please download and reinstall the drivers from the touchpad for your laptop on the Site of HP Support
Please click on this link to find several troubleshooting steps to solve this problem
Please find the screen shot as shown below for your reference:
Hope this helps, for other queries in response to the post and feel free to join us again
* Click on the star of CONGRATULATIONS on the left to say thank you *.
Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.
Thank you
K N R K
Although I am an employee of HP, I speak for myself and not for HP
-
Problems with the help of control Edit Expression with tab control
Hi all
I am facing a strange problem when using Expression Edit Control with a tab control.
When I put the Expression of the RichEdit controls on several tabs in a tab control, and when I run the application, the Expression Edit controls in a single tab are visible, others get invisible! I do NOTHING with them, but they do not simply show upward!
I first faced this problem using Expr editing controls in Visual Studio c#. NET - with tab controls. For verification, I created a simple VI is LabVIEW to see if the problem is with my request / problem with Expression Edit controls in c#, etc. But voila! A similar behavior in LabVIEW too!
I'm doing something wrong? OR do not do something right? Ask someone for help please ASAP!
Thanks a ton in advance!
DASI
PS: Attached the VI here (LabVIEW 8.5) just download and run it, and you will see probably what I'm talking about!
-
E5 - 511 problem with touchpad Acer.
Hello everyone. I have a problem with the touchpad when I slide my finger on it, pointer does not move smoothly, it is very laggy. When I connect to my mouse, it works fine and smooth. I tried to find solutions on here, but none of them worked. Any ideas? Operating system is Windows 8.1.
It solved! Found solution here, thanks for the suggestions. Win8 uninstalled and installed again with UEFI boot.
-
Problems with the help of Deskjet 3745 on home network 2-PC
I have an old PC running Windows XP SP3 and a new one running Windows 7, but only one printer. The network that connects the PC is on an ADSL router with its own external Iomega network drive with a USB port.
To make the printer can be used on two computers,
- I initially plugged on the Iomega USB port. But the port was effectively a 1-way connection, so I couldn't preview before printing to see which form/profile of the printer used. So I put discarded and...
- revenue to the printer connected to a PC all the time and share it on the network. But two different PCs drivers needed which would not talk among themselves, and the establishment would simply not work.
- Finally, I went back to the simple method of the printer on the USB port of any PC, sure I needed it for us. Worked well for a while until the WINDOWS 7
- Print preview has begun showing empty images (but print correctly).
- print-queue doesn't have to face the cancelled documents.
I had help of Deskjet Support to address this issue, which even reinstall the drivers on two PCs - several times! But I'm still left unresolved 3 problems with Win 7 donations.
Has anyone encountered a similar situation and found a satisfactory solution to work?
Try the following: connect the printer to the XP computer and set the machine XP to share it on the network. On the Windows 7 machine go devices and printers folder, add a printer, a local printer, create a Port, Local Port, \\Computername\Printername (use the name of the actual share of the computer and the printer), OK, and then click Windows Update, and then select (not Hewlett-Packard) HP Deskjet 3740 series (Bobo).
-
Problems with the help of Windows 8 Mail
Hello.
I encountered some problems with Windows 8 Mail that I hope you can help:
I configured the other IMAP email accounts on my Windows 8 Mail. But facing problems with it;
(1) emails took very long to cool. Also I'm unable to delete e-mails. As soon as I delete a message, it appears again and gives an error - Email is not available
(2) cannot create new folders. Gives an error - the action I'm doing may not be completed.
(3) I am also unable to save an Email Signature with links. It won't let me save a plain text signature.
Y at - it a setting that I missed? I thought that the option of e-mail with Windows 8 has been very effective, that's why I chose to merge my other accounts work for this.
Help, please. Thank you
The Mail app can not handle the mail POP and is limited to Basic for IMAP mail functions. Use the post office to work. You'll have more control and features.
-
When I use the HELP TAB from the main screen, I can connect to any website but I am trying to access documentation crashes Dreamweaver.
for example
Help (microsoft message asking to send the text of the error returns)
Getting Started with Dreamweaver
Whats's New in Dreamweaver (crashes without an error message)
Any help or advice appreciated
Tony ProdgerUpdate my problem - solved.
Found the answer on Adobe TechNotes
http://www.Adobe.com/cfusion/knowledgebase/index.cfm?id=6d7a2c59
Problem with Internet Explorer 7
Thank you
Tony Prodger
-
Known problems with the help of 64 bit Essbase with version 11 planning?
Hello Experts,
One of my clients is considering moving to the 64-bit Essbase. Are there known issues with the help of 64 bit Essbase (11.1.1.0.00) with the version 11 planning?
Thank you
JingleI tested and there is no problem at all, if your planning server is 32-bit, you just install the 32-bit Essbase client that can communicate with the 64-bit server.
-
Problem with the help and support after Windows Update
Hello
After downloading some updates from microsoft, I now cannot open the option "help & support". It is said ' sorry Internet Explore cannot download / help.
Anyone got any ideas how I could restore the option ' support & "?
concerning
DaleHello
It would be useful to tell us what operating system you have and what computer you have. Regarding your problem:
who help and support option do you mean? Help windows?
Moreover, already checked the website of microsoft? Would be useful for you since almost all topics around the windows are covered here.
Visit this link for the support of the MS Web site: http://www.microsoft.com/europe/
Welcome them
Maybe you are looking for
-
Looking at a CRM Dynamcs in Firefox
When looking at a CRM Dynamcs in Firefox screen renders the m slipped on a mobile phone. In IE, I can change the view by using the compatibility settings but I can't find similar in Firefox. Any ideas anyone?
-
I have a lot of Hp dx2000mt towers I put embeded Thin PC from Microsoft, Windows 7 on. I have no sound on these machines, when before with XP I had audio. I downloaded the latest audio drivers I know a Slimdrivers free program. I tried to use HP driv
-
Reduces the display size of font on Windows Outlook
The display of fonts on my Windows Outlook, now apparent reason, reduced to an unreadable size when you create an email. I write the email to a font size of about 90 to be able to see the text and then reduce it to 12 before sending, so it won't be s
-
Install windows 7 on HP Ultrabook B003SA
Hello I want to install Windows 7 32 bit on my HP Pavilion Ultrabook b003sa via USB but can't do it. This laptop has 320 GB HDD and SSD of 32 GB I turn off secure in the Bios boot. When I try to install windows 7 iam get after message show in the pic
-
System image recovery question
Recently, I managed to get my HP Envy laptop (model: E1P05AV) sent repair due to confer a certain problems. I was wondering if restore a system image on it it when I came back would cause problems back to the image. Wouldn't be better to simply resto