Problems of monitoring of resources http (no response time)

Similar Questions

• SG200 - 26 [FW - 1.1.2.0]-very high response time: > 1000 ms!

  Hello

  Problem: New SG - 200 26 Smart Switch with the latest Firmware - very high response time 500-800 ms

  We have a router of EdgeMarc 4500 with 10 VPN tunnels at 10 locations of brach. SG-200 26 Smart Switch is connected to 7 servers (Terminal 2, SQL and others), all locations have 50 MB download and download 20 MB of Verizon FiOS Internet service speed.

  Depending on the tool Kulvik, the response time of this switch is around 500ms. At the same time, the response time of the EdgeMarc 4500 router is around 40ms and less.

  We have 60 remote desktop computers connected to our SQL Server database and 40 users of RDP via Remote Desktop. The configuration is the same for 3 years. But we change the switch HP 1800 - 24G of Cisco because of some failures of connection. For connection failures, we first think the old switch from HP, but it looks like problem with router EdgeMarc.

  This response time is normal? I have attached two screenshots of Switch Cisco and response time for the past 24 hours EdgeMarc router according to the tool Kulvik. Any other advice would be greatly appreciated. Thank you.

  Hello Srinath,

  Thank you for your participation in the community of support to small businesses. My name is Nico Muselle of Cisco Sofia HWC.

  The response time of the switch can be considered quite normal. Reason for this is that the switch gives CPU priority to its actual tasks that would be sure to pass, lists of access, VLANs, QoS, multicast, and DHCP snooping etc etc. As a result, the switch itself ping response time does not show in any way the good operation of the switch.

  I invite to try the rattling customers connected to the switch, you should be able to notice that the response time to customers are much lower than the response time of the switch itself.

  I hope that answers your question!

  Best regards

  Nico glacier

  Senior Network Engineer - CCNA - CCNA security

• HTTP 400 response code

  Hello

  I'm trying to set up an HTTP connection with a Web site to retrieve some info and update my SQLite database. I use the MDS in my Simulator and I get a HTTP 400 response code when I try to access the web page. Just to test, I tried to set up a connection with http://google.com/ and which worked very well. Thinking it was a problem with my url, I copied the url that I use in the browser on my computer, and it worked fine. Any suggestions?

  Got it to work. I just use url = url.replace (' ', '+');

• Purchase monitor – issue of response time

  I'm considering buying a monitor ASUS: the PA238Q.  It has a response time of 6ms.

  I know that the video game people would consider it's slow.

  QUESTION: Is it appropriate for video editing with first Pro CS5.5?

  Thank you.

  Yes and it's a fast parser for IPS. See http://www.kitguru.net/peripherals/monitors/zardon/asus-pa238q-led-monitor-review/6/

  Only drawbacks are LED lighting and only 250 cd/m2 brightness, but these specifications will hamper you not for video editing, and certainly not for the price. It looks like an excellent choice.

• EXTREME slowing windows 7 professional 64-bit response time, possibly problem driver network adapter? Help, please!

  I have Windows 7 Professional 64 bit installed on a computer, I built

  Data sheet:
  Processor Intel i5 750 (stock clocked & stock cooler)
  Card mother Gigabyte GA-P55A-UD3P
  G. Skill Rip jaw DDR3 1333 RAM (standard timings)
  Western Digital 640 GB SATA HD
  Card EVGA 8800 GS SC Video
  Creative Sound Blaster Audigy SE sound card
  Powersupply Coairsair 650W
  Samsung SATA DVD writer

  My problem is, after I started and had my computer running for a significant amount of time (30 minutes to an hour), I loose full internet connectivity and the response time for any action I'm trying of the preform is from 30 seconds to 5 minutes.

  This problem occurs almost every time my computer is started for a significant amount of time, and it's extremely annoying.

  First Firefox, Google chrome, or internet Explorer stops receivers internet connectivity (because it is not sailing to any web page) but still related reports.

  (during this time and on my computer don't report any anomaly, IE CPU utilization / ram uses / temperature are amounts all acceptable)

  I usually try to close my browser (s) web, but its reports "not responding" and I cannot close or even end the process or the process tree, so it runs as a process. From there a program or a click I do I try to run either doesn't work or takes 30 seconds to 5 minutes to register if they register at all.

  Programs I all ready have running continue to run, IE Vuze, WindowsMP, Zune software, openoffice. But once that I close them I can't reopen.

  Any program I try to open starts a process in the Task Manager but it not to start a program or actually run, and I can't used to finish the tasks that do not work properly.

  If I try to shut down windows, it takes a minute or so to begin to disconnect, then he sits on the "logging" off the screen until I use the power switch to kill the system.

  I suspect that it may be a problem from my network card driver (Controller Realtek PCIe GBE Family, latest version downloaded directly from the Gigabyte website for my motherboard) because the question almost always starts when my internet stops working. However, this may be 2 combined numbers.

  I had this problem and I thought it was because of an installation of bad windows 7 so I erased the hard drive and did a complete new installation, but the problem is back!

  I changed my routers settings to give me a fixed IP address to dismiss questions here. All the other computers in my House have access the internet without interruption during my problems. And no other computer in my house has similar problems.

  I reinstalled the network once drivers without success.

  I would like to address the downturn extreme Windows 7 after half an hour or so if possible because I have other NICs lying there if the problem comes from the network card.

  I'm pretty computer savvy and I've exhausted all my ideas, so any notice are useful! Thank you

  OK, so I think that the slow issue is resolved now. I blame intel speedstep, while part of my problem is fixed.

  Internet connection problems still remain.

  I ran my computer in safe mode with network for about 2 hours. When I booted in safe mode, everything was fine, internet connetion worked on download and upload at full power. I let it sit for an hour or two in safe mode and I came back and there is no internet again, as usual. All my browsers (internet explorer, my main browser firefox and chrome) refuse to function / load anything and their work will not end in the Task Manager. The device says it all works and it (network adapter) said I have a connection, but I am squatting me on my browsers or any other uses of the Internet. This test will run on a network interface card that I installed, with drivers. I did him wrong with shooting my motherboard cable network and its software driver port. This new card gives the same result, so I think now I know that this issue has nothing to do with my physical port or its drivers.

  The only things I can think that it either now are either:
  my router
  However, all the other computers in my house (3 of them, 1 win XP), 1 Win 7 64 bit pro, 1 Ubuntu and my Xbox 360 not having this problem and works perfectly

  or

  Something inside windows 7 that control the browsers or manages connections,
  I think it's most likely due to the fact that my browsers have problems in the Task Manager / they do not work properly

  All reviews are useful,

  Thank you!

• Problems with monitor CF11

  My Department has recently installed CF11 on a new server redhat.  I can not monitor working properly.  I activated the surveillance and profiling and Monitoring Server.  I can get the monitor to launch and am able to connect.  However, it shows not all applications at all.  In addition, any changes I make in the monitor (for example tracking alerts or # last to list jobs that are more than # seconds) without saving.  Any thoughts?  I was able to define alert configurations via the API, but they are not "seems to work.

  After a lot of headbanging, I realized that 'impossible to invoke CFCS' error is the result of trying to run the monitor via the SSL protocol.  I added - Dcoldfusion.disablejsafe = true in the file next and restarted CF.  If I run the monitor of the https://srv-webdev-01/administrator/, it opens the URL for the monitor as http://srv-webdev-01:5500/CFIDE/administrator/monitor/launch-monitor.html.  Then he tells me that I'm disconnected from the CF server and makes me authenticate.  When I do the start buttons are missing.  If I have http://srv-webdev-01/administrator connection and start the monitor, it works.   Once I'm connected to the administrator under http and https, I can launch the monitor with success.

  Is it possible to only have to authenticate over https?

• The HTTP header response

  I want to see the vary: user-agent in HTTP header response. Can anyone suggest me steps to implement this pls

  It depends on the requirements when you want to see it?
  If you want to a particular page, then you can write a droplet, getHeader variable User-Agent and set the header of the response of the dynamo.
  If you wish for any application then you write a servlet pipeline User-Agent getHeader variable and set the response header in the request pipeline (pipeline DAF).

• Improves the response time

  Here's my current situation. I'm in MARCH the version 4.2.1 of the application I have a test environment 1-2821 router with IPS version of the module 12.4 T, 1-2621 router with net stream is running version 12.2, OS 1-2950 switch and a stand alone server MARCH. When I run the script to test the response time (the time it takes MARCH to warn me of the attack) it takes anywhere from 1/2 hour and 1 hour before the alarm appears where the dashboard is a way to improve the response time? Second, I see the IPS signatures in the syslog, but I don't see them on my request of MARCH during investigations into an attack. If I run a query for real-time, I see everything but cannot investigate the attack.

  I wonder the usefulness of a VINE if you are not running the latest version of the software. Cisco is expected to provide the latest update for you. The question of the DST, for example, causing some of the major problems for us.

  Run a real-time event query to determine if the events you generate are 'collected' immediately. If they are, what are the events? What rule expect you fire? Here is a description of the rules should work (they should take immediately before the start of any limitation).

  http://ciscomars.blogspot.com/2007/02/guest-article-Mars-inspection-rule.html

• Big client - vCenter 5.5 response time of the customer Web U1c / questions of Performance and Navigation

  So we're all aware of the issues with vCenter 5.5U1 WebClient and how we are forced to use it to make use of all the features of the v10, vDS 5.5 vHardware (config switch changes the synchronization problems if an emergency change is done on c# client vDS) VSAN only available via the web client, flash, sluggish to questions do not respond the questions and the list goes with the presentation of the menus and hard to navigate, issues SSO (always after 5.5 upgrades)

  So @ VMware vCenter Architecture Team is going to make an effort to hear and give due to the much needed performance improvements and improvements to the user interface before adding more features and SSO type services which majority of clients don't use not and not force it's customers continue to loose faith its vCenter product?

  Looking for answers with options to remove vCenter 5.5 U1c installation as well as a promise to answer to these in vCenter 6.0 version!

  Here is your answer. First of all, to use Chrome as your browser, then you need to go with at least 4vCPU * 32 GB of RAM & adjust the segment size of java for SSO, Tomcat, (TC) Management Server, inventory server and profile based storage to "refine" vCenter device with DB Oracle embedded or external memory. I did, and performance gains went 10 X. This includes the vSAN enabled running clusters. My recommendation that works very well based on design documents:

  vCenter Server inventory	VMware VirtualCenter Management Webservices (tc Server)	The inventory service	(Sps) profile-based storage service
  Large (more than 400 guests or 4000 VMS) stock	4 GB	12 GB	4 GB

  Setting on the vCenter server 5.5 of the memory unit

  • Connect the unit to vCenter server using SSH
  • VI /usr/lib/vmware-vsphere-client/server/wrapper/conf/wrapper.conf configuration file, locate the JVM memory section and change maxmemory to 4096

  Line 66

  # Memory #wrapper.java.initmemory = 512wrapper.java.maxmemory = 4096 JVM

  • /usr/lib/vmware-vpx/inventoryservice/wrapper/conf/wrapper.conf VI configuration file, find the setting. MaxMemory and replace it with 12288

  Line 116

  # Size (in MB) maximum Java heap wrapper.java.maxmemory = 12288

  • VI /usr/lib/vmware-vpx/sps/wrapper/conf/wrapper.conf find the setting. MaxMemory and change from 1024 to 4096

  On line 154

  # Size (in MB) maximum Java heap wrapper.java.maxmemory = 4096

  • Restart the vCenter device w / DB (1000 hosts) external /embedded for lab (100 guests)

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC&docType=kc&externalId=2005086&sliceId=1&docTypeID=DT_KB_1_1&dialogID=294472825&StateID=1%200%20294492358

  Documentation Centre of vSphere 5.5

  PS: vCenter 6.0 has much better performance based on my beta test... so don't lose hope yet. Many improvements to come...

  PS: I've also broken down on this here until I figured this out just recently: Re: big client - vCenter 5.5 response time of the customer Web U1c / questions of Performance and Navigation

• Get the response time data VI

  Hi guys,.

  I am trying to use CD get time response data VI my VI. When I choose the pair of input-output, I can get the response data determined by the digital input to the output value. However, I need more of a pair of response data. I try to use the list of input-output, but there is no output data and response time of the VI with table 1 d of numbers.

  My question is how to use the CD get time VI data response with the list of inputs-outputs configuration? Thank you.

  Hey, Shapiro,.

  I think the problem is you have two 0 items in the above table for you will be out this definition data twice. Let me know if this does not solve the problem for you.

• JKI event response time

  Hello

  I discovered jki awhile but, never had the opportunity to use it. Today I'm trying to see how it works

  but I'm having problems when the task are back on themselves a mount of idle time is not attentive

  before the end of this taks: for example waiting for an instrument prior to prepare you.

  Its there a way to have a response time of more short UI

  here a basic example of 8,6 it could takes between 0 to 3 s to stop

  Best regards

  Tinnitus

  I often force them to pass through a State of rest when I'm waiting like this.  It has been discussed on the forum JKI here.  You will need to use a time-out value<= 0="" for="" this="" to="">

  

• Incredibly slow Internet response time.

  Original title: taskbar

  I had a problem with incredibly response times Internet. After reboot, I discovered in the taskbar, the icon of the single computer that deals with network connections, i.e. wifi had an x in it, which means it is turned off. (This isn't the icon to connect to the LAN of double work). Because my PC is using wifi and is not also connected to the cable, I was wondering what task is connected to wifi.

  I also noticed that my Internet speed of response actually works at an acceptable speed now that the icon shows it is off. Which task is this icon, so that I can disable it using msconfig and task is WiFi so that one is not?

  I use a Dell desktop computer, through Time Warner Cable. I had the SP3 for some time and that you have not added any new programs or updates, that I remember for a while.

  The only change in my computer added wifi (after moving to a new House/State) about six months ago.

  As a further complication, when I logged on today, connecting to the wifi network shown in the taskbar opened and ran into a mode of connection 'very good '. So yesterday and the previous week, I had access to the Internet with it NOT connected. My taskbar displays a computer screen green with waves in the upper left corner and says "Netgear WNA3100 is connected to...". "my camera wifi router in the basement next to the TW modem.

  Correct me if I'm wrong, but I think that there are two connections wifi different trying to run... one that was working yesterday and one today showing tasks in my bar.

  I blame that for my calculation of the slow speeds.

  Looks like you have three icons of network connection...

  1. area (cable) connection icon - two screens - probably with a red X

  2. the icon of Windows wireless - a blue screen with 'waves '.

  3 - Netgear wireless connection icon describe you it as 'green with waves screen '.

  It also seems that maybe you think that 2 and 3 are separate connections. This is not the case, they will just separate indicators of the same wireless connection.

  Reading between the lines a bit, my guess is that you used to have only 1 and 2, but now you have the 3rd too. If I'm right, probably, what happened is that you have started the application of Netgear wireless configuration, which experience tells me tends to 'support' of Windows wireless configuration without even asking if you want that to happen. All you need to do to get rid of this icon of the green screen is open the Netgear configuration (via its system tray icon) and find a check box saying "let Windows to manage my wireless network connection" (or words to that effect, in addition, it is that the word 'zero' in the text). If you have no network connection after doing this, then you were always in a Netgear configuration and you will have two choices...

  1. Start the Netgear form the menu start and reverse the changes that you just made
  2. Configure Windows to control the wireless connection

  If you want to Setup Netgear instead of Windows use, I think that you will have to put up with the two icons.

  Tricky

• Pavilion 17-F001dx: 'Windows 8 using 100% of the HARD drives with high average response time and low write speed '.

  

  It turns out that it is a pretty known issue windows 8.1 users infestation since at least 2013 and there is not a simple fix, then it cannot be * completely * lack of hp. but I've had two of these laptops, both the same model, one needing to be returned and exchanged for a problem absolutely no report with (hardware failure: ethernet port does not work with lights taped). Both are renovated. Both have been extreemly slow and unresponsive even compared to the lower Brazos powered by the laptop that I had before, but I recently decided to investigate why.

  So if there is something specific HP going on here, I hope that there is a simple fix. My average response time went upward as well more than a minute (> 60, 000ms), so that I'm an aberrant case here against this problem of reactivity/band bandwidth hardrive typical windows 8.1.

  Edit: there is a case with another HP pavilion laptop (intel powered, so there may be a problem of storage driver intel described in the first link) being much worse.

  Did not want to resort to that, but,.
  Going to a new facility to clean up an image of Windows Pro 8.1 from DreamSpark for my school.

  Disappointed by the lack of response. Given the odd subdomain name (h30434), I'm wondering if this forum has been abandoned.

• WebMonitor strong expression of mailBody response time

  Hello

  Please, help me to create expression for WebMonitor strong expression of response time mailBody.

  I got the expression for the availability of transaction webMonitor, I've pasted below.

  could someone please help me create a same response time?

  def message = "Page is not available. Cannot access the URL "+ scope.get("measuredObject/url") +". ";" "
  def httpStatus = null;
  def values = $scope #httpStatus # .values (scope);
  {if (values)}
  httpStatus = values.last ()?. GetValue;
  }
  If {(httpStatus)
  def httpStatusMessage = getWebMonitorHttpStatusMessage(httpStatus?.) (ToString());
  message = message & "HTTP status is ${httpStatus} - {httpStatusMessage}.";
  }
  message += "Please contact technical support.";
  return the message;

  Hi Vicky,

  Just try to understand what is missing from the message into the existing rule.

  WebMonitor Transaction Response Time Check rule

  has a variable of severity level of alarmMsg that references 2 other variables are variables rule.

  -alarmMsgPrefix rule variable named transaction - "high response time. "The response time of ${scope.measuredObject.name} of the transaction exceeds.

  -variable rule alarmMsgSuffix retrieves the response time

  def data = $scope #responseTime # .values (scope);
  responseTime def = 0;
  {if (Data)}
  responseTime = data [0] .getValue (.avg)? : 0 ;
  return "ms, current response time is" responseTime + "ms".
  }

  Golan

• Analysis of response time of NAM

  I have 2 small question:

  First: How Cisco NAM can calculate server, client and network responses while it is not the initiator of the traffic? It is based on the timestamps in data packets? All protocols put a timestamp in the header?

  The second question is: how NAM classify clients and servers? as I see the servers appear as a customer.

  Thanks in advance.

  Performance (IAP) intelligent application monitoring is a key feature that provides the Nam: an ability to measure the response time of the transactions between the client and the server.

  NAM monitors the flow of TCP packets between the client and the server and data response time to bring more visibility in time of response measures (ART) and the latency of the network.

  Next image will share more details:

  NAM request time response (it shows a representation of the total time of the operation as opposed to application response time)

  
  Transaction time / response time measurements (lists and describes measures ART measured by NAM)

  

  Possible NAM monitors conversation and the TCP packet flow between applications/server customers and where it grows the clients and servers.

  -Thank you

  Vinod

  To encourage contributors. RATE besoin.*