Problems of transfer of files on the laptop with USB - Satellite Pro L100

Similar Questions

• Printer LaserJet 4100: Should which cable I for Laserjet 4100 connected to the laptop with USB port

  I have the HP Laserjet 4100 printer. I bought a new laptop with USB ports.  What type of printer cable I need to connect the printer to my laptop? Is there some kind of printer cable adapter, or something else that will do the trick?

  I have the same question about my HP Laserjet 1100 printer.

  Thanks in advance for your assistance expected.

  If I remember correctly, the 1100 uses a cable "C", alias MicroCentronics.  Have never seen an adapter for that one.  On the 4100, you can get a USB to parallel adapter.  They are pretty cheap and available at most CESS (Consumer Electronics Super Store) as Best Buy.  Staples and OfficeMax/Office Depot should also wear.  Online is cheaper if you have time to wait.

  The thing with these USB converters is often must 'install' the cable first.  In other words, connect it to the laptop, then wait so he could install, then connect the printer.  Depending on your operating system and if you have correct updates that can be almost instantaneous, and you may not even see it pop on the screen.

  Best idea is that since these are obviously not portable machines, connect them to your router via a network card.  I had the 1100 years and used a cheap 170 X.  I know most recent are available which are faster.

  For the 4100, see if you can retrieve a Jet Direct 620 unit on eBay.  Probably less than $50 and sometimes even as little as $25.  Stay away from the 600, 510 or 615 cards.  Low or as the 600, they can leave your network open to hackers.  No need to get Gigabit cards as they will be well above what the 4100 can handle.

  Now, two of these old devices, processing power and memory can be a problem.  Never try to print documents online.  Save them on your laptop, and then print.  You will probably get communication errors if you print directly from IE or FireFox.

  If the 1100 does not die, not even worth fixing.  Put into a Fuser is a nightmare.  The 4100 will probably work for another 20 years if you keep to clean and replace the rolls before they cause jams.

• Can not find the latest version of the BIOS for my Satellite Pro L100

  Hello everyone,

  I'm looking at the latest version of the bios for Satellite Pro L100 (PSLA1E).
  I can't find it on the Web from Toshiba site because it is a product at a reduced price.

  The BIOS download page is http://www.toshiba.eu/innovation/download_bios.jsp
  The older models, you can find if you use the option product type > Archive.

  Your Satellite Pro is in the list and latest version of BIOS is WIN 3.00.

  I don't know if there is a problem with your laptop but if everything is working properly and stabile don't change anything.

• is it possible to transfer MP3 files to the flash drive USB to hard drive SYNC?

  See the title.

  Hi Tom,

  Yes, it is possible to transfer MP3 files, a flash drive USB external hard disk by connecting the two devices to your computer using two USB ports, and when the two are detected, you can copy the contents of files MP3, flash USB drive files and paste it on your external hard drive.

  For reference:

  Transfer files and settings from another PC:

  http://Windows.Microsoft.com/en-in/Windows-8/transfer-files-settings-another-PC

  Transferring files and settings: frequently asked questions:

  http://Windows.Microsoft.com/en-in/Windows-8/transfer-files-settings-another-PC

  Moving and copying files by drag-and - drop:

  http://Windows.Microsoft.com/en-in/Windows7/move-and-copy-files-using-drag-and-drop

  If you need further assistance on this topic, let know us and we will be happy to help you.

• How can I transfer files from the laptop with a broken screen of a new netbook under windows Vista 7

  I tried to use an old cable and even if the netbook can see old computer I can't access my files on your old computer, it is said that it wants a username and password, I put these in but they are not accepted, im stuck and don't know what to do. someone please help

  Hi mandyXH,

  Step 1:

  You can try to use an external monitor and check if it helps.

  Links:

  Move windows between multiple monitors

  http://Windows.Microsoft.com/en-us/Windows-Vista/move-Windows-between-multiple-monitors

  Set up multiple monitors

  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-multiple-monitors

  Step 2:

  Because you have made a new computer and want to move the data to the new machine, you can try to copy files and folders to an external hard drive and then move it to the new machine and see if it works or not.

  Step 3:

  You can also use the easy transfer cable easy to move files and settings from one operating system to another operating system.

  Check out the link:

  Transferring files and settings: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/transferring-files-and-settings-frequently-asked-questions

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer

• Problem to browse to files in the page with the text field with special characters

  Hello.
  I have a very interesting thing happening in my APEX (4.0.1) application.
  
  I have problems with a text field, because when I insert the text 'aaaaa' and send the page, the text is transformed in "Aaa£ aa.
  After some time trying to understand the game characters and translations and etc, I realized that this thing happened in some pages.
  
  Then, I started to remove components of the page where it happens and I discovered that what initially is an element to browse file...
  Every time I have send the page, if there is an element of browse file created on the page, the text is changed. If I delete the queue item browse, when submitting the page, the text remains correct.
  
  Is it supposed to work like this? And if yes, why is it?
  
  Thank you.
  vssantos
  
  Published by: vaissantos on April 1st, 2011 22:45

  Is it supposed to work like this?

  No, of course not.

  Of one of your previous posts, it seems that you use the APEX? If so, similar problems have been reported a number of times before: + {: identifier of the thread = 1104224} + suggests a fix.

• Impossible to find all the drivers XP for Satellite Pro P200-15W

  Hello everyone.

  I just installed XP Professional and now I have problems with some drivers. The laptop is a Satellite Pro P200 15W and the drivers are:

  Graphics card (specification says that it is an Ati Mobility Radeon HD2600, and I have not found the pilot)
  Wireless card (both pilots in the toshiba download page don't work)
  Audio device on Bus Audio High Definition (I installed the audio driver, but after that, appears this 'new' device)

  In addition, it appears an unknown device and I have no idea on what it can be

  I searched many forums and pages, and everything I've tried has failed.

  Can someone help me?

  Best regards and thank you

  Wait a minute of traditional knowledge. You confused me completely. All the drivers, tools and utilities are available on the download page of Toshiba under http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

  Sorry, but I must ask you something: what exactly is your problem? As you can see he is also classified document called Instructions of facilities. All you need to do is install it using the order of good facilities. Have you ever done this?

  BTW: Have you installed WXP including SP2?

• What is a current market value of the Satellite Pro L100-125

  Hello

  I currently have a laptop Satellite Pro L100-125, that I've had for a few years now.
  It's getting on abit I know, but until recently, he did everything I needed it to do. Unfortunately, I had a small accident and the laptop has been damaged.

  Asking for a new home insurance since I'm not able to buy a new laptop for now (being student humble and everything!). The insurance company asked about the damage and the value of the computer.

  The damage, I know, this is the current value of the computer that I'm not sure of!
  Its probably not much, but if I get it wrong then a number of things can happen!
  If I declare that the value is higher than it actually is, they say it's fixable or say that it is a fraudulent application!

  If I declare the value too low, then we'll write him offshore but I get a very good replacement (I know it's the lesser of two evils and looks like I'm just try on, but this claim will push my premiums until next year regardless, so I might as well get the best that I can possibly get out of it!).

  Anyone happen to know the current market value of a laptop with the specifications below?

  The computer is a Satellite Pro L100-125
  Intel Centrino Duo T2400 1.83 GHz
  2 GB of RAM (512 MB originally)
  60 GB HARD drive

  Also, just so that I know what to expect, no one knows the approximate cost of replacing the screen and the housing on this particular laptop?

  Any help at all would be much appreciated.

  Hello

  Satellite L100 series is already abandoned and it seems no more on the market
  The point is that you could buy a new a lot harder for laptop with the best hardware specifications for about 400-500 euros.
  I don't have no idea how the fix would cost, but if the screen or motherboard would have died then the repair process could be a costly affair because the display and motherboards are more expensive laptop parts

• Satellite Pro L100 - Crash during the update of the Bios

  Hello

  I am the owner of a Satellite Pro L100 (PSLA4E)

  On the Toshiba site I downloaded the BIOS update. While installing I read that it was necessary to supply cable is plugged. Before I could cancel for the cable, he had started and then frozen. The computer stopped working and so I turned it off! Since then, I've read that it was a very big mistake!

  When put on the fan starts and I can hear etc cd drive spinning. After 15 seconds, the screen is blank, the computer starts beeping!
  Is there a way to solve this?

  Thank you very much
  Rich

  Hi Richard

  Seems not good buddy from your description, that something went wrong during the update procedure and now the ROM module has been flashed properly.

  Maybe you area lucky man and the motherboard isn't too bad, but only the Rom module must be flashed again.

  Unfortunately, this must be done by the technician of the ASP. You will need to contact the ASP in your country for assistance.

  Good luck and have a nice day

• Windows XP - a problem to transfer big file from laptop on an external hard drive

  I have a problem to transfer large files (mail.pst - zipped file - 5Gbyte) of the laptop (Dell Latitude D630) on an external hard drive (WD 320 G - FAT 32) where each time, I got the message "there is not enough free space on the disk" although I did successfully drive clean on both sides and there is enough space on both sides (not less than 25 GB).

  Also, I did a checkdisk command and he succeeded, and I use Windows XP

  I did several tests to resolve and in the end, I found that I convert the format of external hard drive FAT 32 to NTFS, and then I could successfully transfer the file.

  I used the following commands:

  (1) command line then chkdsk to repair bad sectors

  (2) convert the command line to change the format to FAt 32 to NTFS

  Note: For Windows xp, "convert" command will not delete the files from the hard drive

• Need help with the error message when you try to transfer a file from one laptop to another.

  I'm trying to transfer a file from one laptop to another using Belkin transfer cable. While trying to install software for my old laptop, I get an error message as follows WET7CABLE ERROR OPEN. LOG FILE. I tried with the support of Belkin and they referred me to Microsoft. Please help me with this question.
  Thank you
  Nelson Santiago

  Hello

  It is a matter of easy transfer Windows.
  Read on this and the solution here:

  http://support.Microsoft.com/kb/980870

  Kind regards

  Joel

• I have problems keeping records and files of the administrator and the user separate in my laptop (HP Pavilion dv6700) under Windows Vista Home Premium.

  I have problems separating records and files of the administrator and the user. My computer is a laptop (HP Pavilion dv6700), used as a home computer only by myself, I like to keep the two distinct roles, but am unable to as Vista seems to be considered as one and the same. This scenario has arisen as follows:

  Initially, when I bought the laptop - approx. 18 months back - Windows Vista Home Premium was preinstalled, with the name 'Administrator' as an administrator. To customize the operating system and to use safely, I installed a user 'Renault', as a Standard account user.

  After awhile, I changed the name of the Director of "Renault", for reasons I have can not remember now. This caused Vista to combine folders and files of the two "users" in one, I found difficult to deal with, that I could not operate my laptop as just a Standard user, but is still considered the "administrator." On the one hand, this greatly increased spam in my email accounts. So I tried to reset the name of the administrator as 'Administrator' itself and keep my user name as "Renault", as originally the case.  But Vista me has failed to create a new user under the name "Administrator". So I created a new user under the name "System administrator", with administrative privileges. This has been accepted by Vista.

  But I forgot to change the user account for 'Renault', on the Standard account, so there was BOTH administrator accounts at the same time on my laptop! I realized that now only. The net result was that all the files that I created under the system administrator user were still being displayed under the user account of Renault. A few days back, I realized this and tried to separate the files correctly, but it has not been possible. No matter what I copied the account of the user in the files under the system administrator account, the files have been copied on account of the user himself.

  I tried to fix this by changing the name of the user account in something very different, AND as a Standard user. but this also does not work, as all folders and files under the administrator account system shows it as being under the user account of "Renault" only!

  Then, I deleted the user 'Renault' from the list of the user, but he was not yet of any help. Whenever I tried to create a new file under the system administrator, Vista responds with the message, "C:\user\Rajaram folder is not present. Will I create a new? ", which defeat the same purpose of my tent to isolate the administrator account and the user account.
  
  SOMEONE HELP ME PLEASE WITH A SOLUTION, - OTHER THAN REFORMATTING MY C:\ DISK AND REINSTALL VISTA AGAIN - TO GET OUT OF THIS MESS, IT SEEMS TO ME YOU HAVE CREATED AND HELP ME TO HAVE AN ADMINISTRATOR ACCOUNT AND OTHER UNIQUE STANDARD USER ACCOUNTS PROPERLY ISOLATED.

  I would be always grateful for a quick and helpful response.
  Thanks in advance.

  -RAJARAM77
   
  Thanks for your reply. It was very helpful / sorry your proposed solution has not solved my problem. Kind regards. -Rajaram77

  Better to delete the user account except the one that was built in the administrator account that you renamed. Before this backup all your data files of these user accounts.
  Then rename the buil into account administrator as 'administrator '. Then you create another administrator account and use it and never the user built in Administrator account and leave it alone.

• Problem with the transfer of files from the computer Windows XP to Windows 7 using Windows Easy Transfer.

  Original title: Put WET on the old computer

  When I try to use WET to transfer from old Win XP Win 7 again, I need trasfer WET to the old computer.  So I choose this option and move on to the part where it says "Select the USB flash drive where you want to save WET".  Well, in the window is the word "computer" I can't click on it, nor is the OK button light up.  What's wrong?

  Hello

  Thanks for posting in Microsoft Community!

  It seems that you have a problem with the transfer of files from the computer Windows XP to Windows 7 using Windows Easy Transfer.

  I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.

  I suggest you try the procedure described in the link and check if it helps.

  Transferring files and settings: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/transferring-files-and-settings-frequently-asked-questions

  For more information, please see the links.

  Transfer files and settings from another computer
  http://Windows.Microsoft.com/en-in/Windows7/transfer-files-and-settings-from-another-computer

  Windows Easy transfer

  http://Windows.Microsoft.com/en-in/Windows7/transfer-files-and-settings-from-another-computer

  Get back to us and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence.

• Broken screen - problems of transfer of files on USB stick due to the "read-only".

  I have a screen broke on my G2 bike. I can turn the phone on and off, but I can't get past my password because the screen is unresponsive. When I connect the phone to my pc via the usb port I can still access the files because of the default value to "charge only".

  Does anyone know of a way to change my phone to another parameter as 'charge only' that does not involve the use of the touch screen?

  I tried to use adb to transfer my files using the android devices Manager or command prompt but usb debugging is disabled.

  Even if usb debugging was, would not be required to change the settings for usb 'charge only' in order for my pc to detect the phone?

  The otg worked perfectly. With the help of a mouse instead of the touch screen, I was able to activate the bluetooth and transfer the files this way.

• How to transfer a file from my laptop Windows 7 to Air on my Ipad?

  How to transfer a file from my laptop Windows 7 to Air on my IPad?

  How to transfer a file from my laptop Windows 7 to Air on my IPad?

  Hello

  Some clarification would be useful.

  What type of file you have?

  What do you do with it?

  The easiest way might use dropbox or onedrive. Or you want to change the file on the iPad?

  MP3-files are also. And with iTunes you can copy those dear to your iPad too.