Problems of WAG54GS

Similar Questions

• Problems with WRT610N v2 + WAG54GS v1.0 of port forwarding

  Background:

  I have a WAG54GS v1.0 (Appendix A) that I use to manage my home network and my ADSL connection. I bought a WRT610N v2 (which I will refer to as the router) with the intention that he would replace the functions of networking of the WAG54GS (which I will call the modem), who could be relegated to handling just the Internet connection. Both are running their latest firmware.

  I got this configuration to work, but with a problem: I lost a lot of flexibility with regard to port forwarding. The problem is the only way I managed to get the Internet to work with the 192.168.0.1 router and the modem to 192.168.1.1. If I try and that you have both 192.168.0.x or 192.168.1.x then connect to Internet no longer works under any configuration options, I've tried.

  What wants to say that when I go to port forwarding of installation in the modem, I can only forward to clients on 192.168.1.x, but the router can only transmit to 192.168.0.x. The only things that I can go to work are situations where triggering serial port can be applied, so that when a connection is made to the relevant port to an external IP address, and then this external IP address to communicate on this port. As you can guess this covers almost all cases.

  Question:

  Would it not be possible to have the router and the modem on 192.168.0.x or 192.168.1.x, allowing port translation work as expected. Which should in principle be possible with the modem bridge mode except that it is impossible to configure the PPPoA settings needed to connect to my ISP.

  Or I'll have to rethink the configuration of the network (i.e. buy a dedicated ADSL modem and remove entirely my WAG54GS?)

  In fact in the end what I figured out was that according to my WRT610N concerned my WAG54GS is my ISP and that was all he needed to know on the Internet connection. So I had to connect to the WAG54GS with an IP address static, stuck that IP in the DMZ of the WAG54GS and left the WRT610N to manage port forwarding like all devices that connect will make it through that. (Yes, I've disabled features wireless of the WAG54GS)

  I'm reasonably sure that I tried the combination of settings you suggested (including moving the WAG54GS off the Internet port on the WRT610N, which I wanted to avoid in any case as I have four devices permanently connected in any case) and found that it still does not. And I wasn't saying two to 192.168.1.1 set at any point, my darkened auto focus was that change only the last block of the IP address doesn't have to work for Internet access.

• The WAG54GS Firmware upgrade problem

  Hello

  I am trying to update my firmware using the files provided on the linksys site. I have entered my serial number of the router correctly and chose the model of the good version (v.1.1) and downloaded the firmware file. I have connected my router configuration page, selected upgrade firmware and selected the id of the file downloaded. He got about 10% in the upgrade, and then he said it's the wrong file for my router. I currently have Firmware Version: V1.00.12 installed and I try to install the firmware Ver.1.01.03.

  Please can someone help?

  Marc

  Hi again,

  I feel such a fool as I now installed firmware annexed. As already mentioned by Kate, I wasn't directing the update firmware specifically for the IMG file.

  Ah, well you live and learn

  Your timidly

  Marc

• LOCAL M40X-230 WIRELESS NETWORK PROBLEM

  I have a problem with the Wi - Fi connection. After initial startup of wireless lan, speed goes from 54 to 1 MB/s and then continues to jump around making me lose my internet connection. Thought it was the router at first but after 3 new routers, this may not be the case. Last router is liksys wag54gs. Laptop is about 7 feet from the router. Please, I need help!

  Hello, Robert

  On this forum, you can find many topics on the same theme. You can check wireless Board. Check please what a http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=8406

  There is obviously a problem with the Intel wireless card.

• WAG54G v2 faulty LAN

  It seems there is a very common problem with these models works very well for a period and then for no apparent reason the wired ethernet ports stop working. I had 4 devices connected for 2 years without problem until last week when none of the devices would connect with no changes made somehow. Worked for a minute then nothing. It's obviously a hardware problem (component manufacturing/MTBF default) as the lights on the router ports do not come on (only on the initial power of the port test), or isn't on any network devices - they always have, but no more. If this were not the case, then surely a FW version could fix.

  What does not seem work evolves unit setting of the Auto - 10 MB/s speed & duplex half. It is said in many places, even by Cisco as acceptable work around... WHAT? All right, now it connects but no more transfers of video, not bigger files continuously, no longer full speed ethernet. Not good enough!

  (Mod Note: not fired off topic.)

  This isn't a problem of firmware it is a defective hardware problem. I did everything what the consumer can do to remedy this but as I have since found this very common problem is caused by a faulty capacitor on the device. Since then, I've replaced the defective hardware and everything works as it should.

  I would recommend this difficulty to all those who still have a little know how with a soldering iron. Very quick, simple, and this MARKET. I hope that this message is not also edited or deleted because it can be useful to many customers Cisco/Linksys there also well suffer that.

  Here is a link that I found for a portico on what to do, I'm lazy to do the maximum, so here you go:

  http://gavinbenda.com.au/2007/05/27/WAG54G-v2-capacitor-replacement/

  Accessories for Gavin for this tutorial.

• WAG54GS allows wireless clients to connect but will not assign IP addresses for full connectivity

  I have three XP 3 computers connected between them in a MS home network via a wired hub and access to the internet through a wired connection to a router WAG54GS.  DHCP is enabled on the router, the IP addresses are correctly assigned and internet access to these computers Wired is not a problem.

  In the past, I've connected also with success of laptops to the internet via the feature wireless router, but having not used that for a while, I think now it will not work.  I tried to connect with laptop computers running XP 2 and Vista Home and the problem is the same.  Laptops find broadcasting wireless router and connect but they are not assigned IP addresses during the phase of "Acquiring IP address" resulting in a "Limited or no connectivity message."  Packets are sent to the router, but none are received in return. It is with the strength of the Signal at 73% and the quality of the link to 100%.  Ipconfig displays no deafult assigned gateway and the IP auto configured to be 169.254.96.1 for example.  Ping the router gives "Destination host unreachable".  Not surprisingly, laptops are able to 'see' other computers wired on the MS. network  These laptops connect correctly to the MS network and internet if I change the wired connection.

  If I check the status of the network wireless router configuration good laptops MAC addresses are displayed, but the computer name and the IP address are missing.  I usually use a protection WEP 128 bit on two channels 6 and 13, but it makes no difference if I change this without guarantee, once again the connection occurs, but no IP address is assigned.  DHCP is enabled in the tab for basic configuration of router from 192.168.1.100 with selected up to 50 users DHCP (and DHCP works very well for cable customers).  The IP address of the router is set to 192.168.1.2.  Wi - Fi router is set to "allow everything".  Default settings are used for the parameters wireless advanced, although I tried to reduce the 100 interbval tag at 50 and the RTS and Fragmentation threshold to 2304.  The policy of Internet access on the router is disabled.

  If I have (for purposes of testing only) connect laptops to one of my neighbors secure networks (there are several) to connect laptops very well so I can access the internet, DHCP works great on laptops.  Firmware is v1.00.08 (I looked this modernization, but while I can identify my router version 1.2 downloads talk about types of Annex A and Annex B are mutually exclusive and I'm not clear I have.  I am also doubtful as to if the firmware upgrade would make a difference, because there is no trace of the upgrade solve this kind of problem and I had the Wireless does not work if long ago).  I'm running out of ideas, is there something that I missed?

  Well in this case you can try to upgrade the firmware of your router, go to the website http://www.linksysbycisco.com/UK/en/support/WAG54GS/download...insert of your router model serach tab... select the correct version of your router... Download the firmware file... save this file on the desktop.

  Follow these steps to upgrade the firmware of the device: -.
  Open a page in Internet Explorer browser on a computer hard wired to the router...
  In the address bar type - 192.168.1.1... Leave the name blank username & password use admin lowercase...
  Click the 'Administration' tab - then click on the 'Upgrade Firmware' under the tab-here, click on 'Browse' and navigate the .bin firmware file and click on "Upgrade"...
  Wait a few seconds until it shows that "the update is successful," after the upgrade of the firmware, click on "Reboot" and you will be returned to the same page OR it will say 'cannot display the Page.

  Now reset your router:
  Press and hold the button of reset for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...

  Once you re-configured settings of your router, and you are able to go online Wired computer, here are some settings that you can configure your wireless router, I think this might solve your problem

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1
  Let the empty user name & password use admin lowercase...
  For wireless settings, follow these steps: -.
  Click on the Wireless tab
  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Set the Standard - 20 MHz Radio band and change the Standard channel to 11-2, 462 GHz... Wireless SSID broadcast should be enabled and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WEP wireless security, encryption must be 64-bit. Let the empty password, do not type in anything... Under type of WEP Key 1 in all 10 numbers please (numbers only and no mailbox for example: your 10-digit phone number) and click on save settings... Please note the 1 WEP key as it comes to the security key for the wireless network...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304, change the RTS threshold to 2304 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect... And check if you are able to navigate.

• WAG54GS-> settings E3000

  Hi This is my first post here.
  I would like you to ak you a few questions. I have the WAG54GS router with this settings

  except that the LLC is not on VC. My problem is that E3000 support only PPPoE. This is not a problem because my provider also supports PPPoE. I don't know how to select LLC in my E3000. And secondly when I put PPPoE MTU 1492 - DHCP server username password disabled I connects. When I press the button on the status bar to connect it tells me that it cannot find any ip provider.

  With my other router WAG54GS I'm ok with the entire network but with 3000 the autorun of the cd event guide not found internet connection even though it is the same cable used in the two router for internet.

  My line is PSTN. When I call my provider for assistance they tell me the settings for all of the routers supported their company Linksys AG310
  LinksysWAG200G
  LinkSys WAG54G
  I try to explain that when when I connect the internet cable does not find my 3000 and they say to me that's all is not possible. Can you please help me with the settings? Because I think that's not possible 3000 unable to connect to the internet.

  Sorry for my bad English.

  Here are the settings for my provider Forthnet

  http://www.forthnet.gr/templates/supportPosting.aspx?c=10007410

  I know that there are in Greek but find you a way, that there are a lot of photo

  Thank you once again

  The E3000 is an ethernet router. However, there is no built-in ADSL modem. You will need a DSL modem which you connect the E3000.

• Window update causing problems of printer driver

  Hi, I have a laptop running XP and router wireless computer (WAG54G) and a set of HP6380 in one. About 2 nights ago an update to Windows Installer by himself and rebooted the laptop (even though I have some turned off automatic updates what they seem to be screwing with anything these updates produce still grr)...

  I went to try and print and to found the 6380 was absent from the list of available printers... The problem is not with the wireless network (as it is trendy and functional). I don't know what it does the update of windows... but when I tried to reinstall the drivers for this printer from the disc, he acknowledged that they were already installed... So I uninstalled them instead (and it is taken up only parts of the driver remained and he removed these pieces).

  Then I tried to do a fresh driver... install that took a long time because it got stuck at the end... Finally, he came up with an error and so I tried to introduce him, HP - and received click on a desktop icon... (Icon HP - XP Installation). I tried it but it tells me to 1) Reinstall driver (done twice -) solve printing problems wireless (not a problem at this point given that I have no printer driver and I can use the network wireless for other things very well) well tried anyway... or 2

  Anyone has any suggestions please > in the past when Windows updates have caused problems, I used the system restore to roll back, but this is only a temporary solution - as Windows insists on the updates I want!

  Thank you very much!

  If you have the original HP software CD, look in the folder of the ccc/utils for a L3_unintsall (or similar).  Run for an uninstall very full.

  Reset.

  Now, download the latest version of the software for your printer from the "Support & Driver" link at the top of this page.  DO NOT reinstall from the CD (a good rule is in general not the CDs software, but to go to the website of the manufacturer for the latest and best).

• Unable to connect via the wireless router "problem with wireless adapter or access point" _

  Hello

  I recently replaced my old Toshiba laptop with a new model of Toshiba Satellite L500/033HNX, it installed Windows 7.

  The problem is that I can't connect to my wireless network. I am currently connected via Ethernet cable to my Linksys router.

  I had help from my internet service provider, the installation correctly the problem not because of the connection.

  I had a Linksys online support, the router is a wireless, model - WAG54G ADSL gateway, is not the problem of all the correct settings and other devices can connect via my wireless network. I ran Dr. connectivity several times and it is always impossible to connect, "problem with the wireless adapter or access point.

  OK, you're my next hope to solve the problem can you HELP Please!

  Hi, JoelbX
  I want to thank very you much for your support and effort do to help me solve this problem, but we receive have been, and I don't want to waste any more of your valuable time, so I am the son of closing and deleting of Tring in Microsoft Answers.
  All the best
  Tring

• Unable to Scan to the computer after downloading macOS Sierra. Is this a software problem?

  How can I scan from HP Envy 4500 to computer after downloading macOS Sierra?

  Hello wdemetris,

  Thanks for asking for scanning helps here in the Apple Support communities. I understand how it is important to have access to your scanner and am happy to offer help for this.

  As a precaution, we always recommend that you have backups to make sure that all your data is safe. You can perform a backup using Time Machine and an external hard drive. Use this article to help make a backup of your Mac: use Time Machine to back up or restore your Mac.

  Then, in accordance with article help: printer and scanner for Sierra, El Capitan, Yosemite, and the Mavericks macOS software, the HP Envy 4500 e-all-in-one is supported for printing and scanning. The drivers must be installed, but if not, if it please go to the App Store and check the updates tab to see if there are updates for HP. If there is, please install.

  If you have only general questions about how to get your updated scanner in place or how to scan pictures, please check out these two articles: macOS Sierra: implement a scanner & macOS Sierra: scan images or documents. If everything is configured correctly and you still have problems scanning, please visit this help article: macOS Sierra: scanning troubleshooting.

  Thanks again and have a great rest of your day.

• My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  Hello brooksm549,
  Thank you for using communities of Apple Support.

  I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

  Maximize the life of the battery and battery life

  Best regards.

• MacBook Pro display problem

  Hello members of the community.

  As of recently, I have noticed some glitches when feeding on my MacBook or awakened from his sleep.

  The colors are distorted, usually with pink, green, or yellow blobs. Blobs cannot entirely replace the colors, they appear to be contained in a element would normally be. For example. the menu bar will be partially pink and white, but pink does not leave the menu bar in this area, and the Office has green lines on it.

  I tried to take a screenshot, but the problem resolves in about 20 seconds, but it's a recurring problem.

  It happens when I wake up, connection or not. I had also certain powers serious and problems of performance, such that my MagSafe LED would not illuminate when plugged on rare occasions, fan could turn unnecessarily, graphics performance were SUPER slow, and the health of my battery was running out quickly. I actually ran a report on the system at 2 different times and my quality of full load is depleting of 1.2% per charge cycle, which is very worrying. I went from 6281 mAh mAh 6138 maximum capacity after two cycles of load. I'm tracking closely it because at this rate, my battery will survive only at load cycles about 150 instead of the 1000 expected, gives me the idea that this could very well be a bad battery. The computer is also warm to the touch while you sleep, not connected to the power supply. I NAP active but even taking into account should not be hotter my iPhone did the same thing.

  I have reset the SMC, and it solved a couple of problems. The charger works fine now and my performance improved considerably (which made me feel better, either it is a high-performance laptop, a 11-inch MacBook Air should not he surpass), and battery life has improved. I feel even if it uses a lot of power in his sleep. Maybe I need to turn off the NAP and see if that makes a difference. The graphic bug still persists however, and I don't have enough time to see if the max battery is depleting again.

  In regards to the bug, is there something that can be done? Basically, I want to assure you that I took all appropriate measures or if someone else has this problem to see if it can be software related instead of my computer.

  I have the entry level MacBook Pro with the retina, last generation.

  Any constructive contribution welcome!

  See you soon.

  -adreaux

  Hello bernardn753,

  After reviewing your post, it seems that you are having problems with the screen showing strange things on it. Looks like you already have a troubleshooting. I recommend you read this article, as reset NVRAM would be to reset your screen resolution settings that should help.

  How to reset the NVRAM on your Mac.

  Thank you for using communities of Apple Support. Good day.

• with IOS 10.0.2 - 5s iphone Bluetooth problems

  Since upgrading ISO 10.0.2 my M50 from PLT Plantronics (helmet unique headset) do not reliably connects with my iPhone 5 more. I have to go to the settings, activate bluetooth turned off/turned on, touch the device on the bluetooth page, etc. Once it connects successfully, it will reconnect (if I turn off the headset and turn it back on) for a short period. The next day he does not connect itself but I play with bluetooth on the iPhone again.

  It has always worked perfectly before the 10th of IOS.

  And, as I noticed others mentioning, the volume is much lower with IOS 10. The maximum volume is much lower. I can barely hear it now, more normal background noise, while driving.

  I did:

  Forget this device for the PLT M50 and paired again (several times)

  I did a Reset Network Settings

  I don't know what else to do - but it's a 10.0.2 IOS issue.

  Hello AppleUser2k,

  Please ask questions about your problems of connection between your iPhone and your Plantronics headset since you upgraded to iOS 10. I understand how important it is to have your Bluetooth devices connect with your iPhone with reliability. Here's what I recommend.

  The first thing we want to make sure is that all your data is safe. You can perform a backup in iCloud or iTunes using this article: backing up your iPhone, iPad, and iPod touch.

  Once your data is safe, try the troubleshooting steps in this article to help: get help to connect a Bluetooth accessory with your iPhone, iPad or iPod touch device should also check with the manufacturer that the device has all the drivers and firmware to work with the new version of iOS.

  If you have checked everything and that you have installed the latest firmware or driver and always are problems, please be aware of your surroundings when you encounter these problems. If you can isolate the time or location, you see the problems, you can isolate the cause. You can even see this help article to ensure that you are not affected by outside interference: the potential sources of Wi-Fi and Bluetooth.

  Thanks again and have a great rest of your day.

• Problem after update 10.0.2 iOS iPhone touchscreen

  After I have updated to iOS 10.0.2, I noticed a problem with the touch screen. Using the position of the image on the right side, near the corner, the toushscreen does not work.
  For example: when you use the keyboard, I can't type the letter 'P', have trouble typing BACKSPACE. Using the Contacts app, I can't scroll through using the alphabet bar.

  Do what idea of the problem?

  Kind regards!

  Hi fabriciorela,

  Thanks for the upgrade to iOS 10! I understand that the right of your screen is unresponsive to the touch. You can try the steps in this link to fix the problem. If the screen of your iPhone, iPad or iPod touch does not respond to touch

  If it does not help the problem, try to restore the device to factory settings. I would like to backup your important data first.

  The backup of your iPhone, iPad and iPod touch

  Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod to factory settings

  Please use the Apple Support communities to post your question. Let us know how it turns out. Have a great day.

• Bluetooth connection problem iPhone - audio system Nissan after upgrade iOS10

  After iOS10.0.2 iOS9 on iPhone upgrade, I got a cordially problem receive calls raise Nissan car audio.

  I can make a call without any problem. Bluetooth connection is stable. I can download address book e.t.c. But I can't receive a call. I see the incoming call on the radio shows. After pressing the button "answer" on the car Audio System, audio between iPhone and Audio streams car breaks down.

  But the cellular connection remains active. I need to rotate the audio output on the screen of the iPhone car for iPhone and back to the car. After that, I can continue my call via the car radio.

  Thanks in advance

  Hello StasV,

  Thank you for using communities Support from Apple. I know having a problem with calls on your iPhone in your car, it's not what you expect. The good news is that these steps will be useful for your problem of phone calls while using the bluetooth in your car. Go to settings > general > accessibility > routing of Audio calls and the value headset/Bluetooth Headset and retest your question.

  Audio routing call - the iPhone user Guide
  Help to connect your iPhone, iPad or iPod touch with your car radio

  See you soon!