The WAG54GS Firmware upgrade problem

Similar Questions

• Shutdown after the last firmware upgrade problems

  After the last firmware update, I have questions turn off my rocket. If I try to turn it off during audio playback, the screen goes all black and turns off, and when turned on, it passes again by updating of media. She does whenever I turn it off if I do not push the button "Play/Pause" first. It's very annoying - anyone else knows this or can help?

  Sansafix said that it will be fixed in the next firmware. So far, just press the Center button until you turn it off!

• The RV042 Firmware upgrade problem

  Hello

  I was responsible for upgrading the firmware on the router RV042 in more than 30 remote locations. The problem is that when I update the firmware the vpn tunnel or office does not reconnect and we lose communication with the router. What can I do to keep the vpn tunnel directly without having to travel to each site just to get the vpn tunnel to the top?

  Thanks for any help.

  Hello

  You should check if the option Keep Alive and the dead peer detection is enabled on both ends of the tunnel VNP. They help to plug the tunnel once it falls.

  I hope this helps

• The SG300 1.3.5.58 firmware upgrade problem

  Hello

  We have two new switches SG300 managed. I updated the firmware of the stock to 1.3.5.58 without problem, but when I upgrade to the new firmware - 1.4.x I get the following error on the two switches:

  The files transferred: 7011840
  Status: Failed to copy
  Error message: copy: the code SW file size is more

  No idea what is the problem? I can't find any option to delete old images. Thank you

  Hello

  you do the upgrade via the web interface? I did the upgrade of 1.3.7.18 without any problem.

  What is your bootloader version? 'show Version' on the command line.

  Kind regards

  Lukasz

• The SPA3102 firmware upgrade error

  Hello

  Although I used my SPA3102 for a few years, she has recently become problematic. I sometimes hear audible clicking from the device that is associated with a red light flashes briefly on the power LED. If I'm on the phone at the time, the call is completed.

  I hope that a firmware update will address the issue, but I have been unable to upgrade 3.3.6 (GW). If I'm on a Mac, I don't understand the method of upgrading firmware using http or tftp. Fortunately, I ran Windows XP under Parallels Desktop for Mac and have been able to run the upg-spa3102-5-1-10-GW.exe program. However, a message is displayed: error in upgrading the firmware of the SPA > upgrade failed: no response from the SPA.

  Reading various forum posts on similar such problems, I was not able to find the solution.

  I have disabled the firewall on my Mac, the router (D-Link DSL 504 T) ADSL and Windows XP.

  I confirmed that the IP address of the SPA is 10.1.1.3

  I made sure that the firmware update is enabled in the Provisioning of the SPA configuration.

  I would be very happy to help you please.

  Thank you

  Bart

  These products are treated by the Cisco Small Business support community. (URL: https://www.myciscocommunity.com/community/smallbizsupport)

• Satellite A350 - cannot order the Win 7 Upgrade - problem of credit card

  To the right,.

  I bought a laptop, A350, in 2009 and ordered to Windows 7 using the www.toshibawin7upgrade.com program, but I couldn't get anything from anywhere until today.

  Recently, I asked the delivery during 2 months nothing delivered, but the team behind this program cancelled my order. (Order No.: 4440058036)

  Day before yesterday, I ordered again (order No.: 4440124899) but this time another email was sent on my credit card because they could not charge the card so that they are not able to send the Windows 7 upgrade.
  In addition, it is mentioned to get in touch with the service the customer in Turkey, but the phone number provided on the page does not work.
  I don't know that my credit card works because I order a lot of stuff from other Web sites in the world.

  Almost 3 months ago, I still don't know where to contact them and how to order the Windows 7 upgrade.

  I hope that during the purchase of computer A350 laptop brand TOSHIBA, but today I am considering my decision isn't true at all.

  Please tell us how to deal with which to order Windows 7 upgrade as announced at the sale of portable for the A350.

  Kind regards
  ALP

  Hello

  For me, it looks like there are some problems with the credit card.
  Who knows what makes you wrong maybe that you have entered the right number or missed something maybe, there is another problem with your credit card
  In my opinion, you should get in touch with your Bank and should ask what could be the problem

  Here are the other Toshiba page where you could ask a support team for assistance if a problem with Win 7 upgrade kit would appear.
  https://www.toshibawin7upgrade.com/Endcustomer/ContactUsForm.aspx

  Welcome them

• CP1025NW firmware upgrade problem

  I'm trying to update the firmware on my CP1025NW printer. The version of the firmware on the printer is 20100510 and the version on the HP site is 20110826. I have downloaded and run the firmware update and it turns a little and then says that he "cannot find the appropriate firmware file". I tried the update through a USB connection to the printer and a Wi - Fi connection running. Both result in the same error.

  Any help would be appreciated.

  Not sure if you have found the solution, but the mine has been change the printer to use a TCP/IP port and the printers IP address.  Once you do this, the firmware should be updated, then you can change it to the WSD port if you wish.

• The phone Firmware upgrade question

  Hi I am upgrading the firmwares a lot of phones.

  Current firmware

  SCCP41.8 - 5-3 216

  SCCP42.8 - 5-3 S 3675

  SCCP42.9 - 2-1 S 13

  P00308010200 25

  Required firmware

  SCCP41.9 - 3-1 SR 1-1 S

  SCCP42.9 - 3-1 SR 1-1 S

  Can I go directly from the existing versions or what I need to do step upgrades?

  Thank you.

  Hello

  You can upgrade directly. The release notes says:

  For all SCCP firmware version firmware updates versions prior to version 8.3 (3) to Version 9.3 1 or

  later, you must upgrade your firmware of the phone to an intermediate version (8.3 (3) 8.5 (2)), then

  9.3 upgrade 1.

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/cuipph/7900_series/firmware/931sr3/P790_BK_R6CE16B3_00_rn-9_3_1sr3-7900-series.PDF

  In your case, you are already using 9.2(1S) and 8.5(3s)

  regds,

  Aman

• For the 32RL938F firmware update problem

  Hello

  Information software update are available appears on my TV. I accept the update and download begins (TV connected to the internet via WiFi) but still hangs on 99%. I tried to wait a few hours ;) but it does not help. Any idea? Has anyone seen this problem?

  ARO
  Pawel

  make reset on television since the installation menu - system,.

• WRT to the 1900AC Firmware update problem

  I have WRT router 1900AC with the Ver.1.1.10.167514 firmware.

  I started to install the hardware version 2.0 by mistake (ver. 2.0.7.167471)

  Now the power button blinks 1 hour ago

  What should do? Restart or wait?

  How can I fix it?

  You can try this?

  http://www.Linksys.com/us/support-article?articleNum=140001

  Otherwise, you will have a number of ARM to dial up Linksys...

• After restart of the firmware upgrade

  Hi, I need to update the firmware on my controllers PS6100 EqualLogic.

  I found the instructions on how to do it and everything seems straight forward to do so via the GUI.

  I noticed there is a necessary restart after the firmware has been applied. Does this mean I have to gracefully shutdown the virtual machines running on my SAN LUNS? My iSCSI connections will be closed/broken during the restart of the post firmware upgrade?

  Thank you, Oliver.

  Hello Oliver,.

  In the same area download notes firmware and release is another PDF, entitled ' iSCSI initiator and optimize your SAN environment for high availability operating system considerations ", which includes some key parameters that will allow your computers virtual and servers through the failover time.  It is important that not only the Firmware update, but in the case of an unexpected failure due to a failure of CM.

  More if you use VMware ESXi, there is a best practices PDF for that as well.  In addition to better manage the failover, these changes have shown to improve performance as well.

  The Tech report TR1091 is available here:

  http://en.community.Dell.com/TechCenter/Extras/m/white_papers/20434601/download

  Changes for Windows and the knots of ESXi virtual machines will require a reboot to take effect.

  What version of firmware you are at, and what version you are migrating towards?

  Other things I always propose updates is to ensure that both controllers are plugged in your switch and in the VLAN correct.  Since assets CM are failed over to the passive, support gets much advertising is unable to access the storage after firmware update.  Or ports of the day before were not in the VLAN correct, or individuals with disabilities, etc...

  It is for these reasons that personally I prefer to do the updates via the serial port CLI.   The process is more talkative, and if something should go wrong, you need the serial port of some sort.   Since the installation and tested in advance is a huge time saver.   Here, we use serial mux so that all array controllers are easily accessible.

  Kind regards

  Don

• BEFW11S4 v.4 and Vista - firmware upgrade failure

  Hello

  I've had this router for about 5 years, it runs with XP without any problem. Since I got a new laptop with Vista, the wireless connects for an hour or two, and then falls back and I have to unplug the router for five seconds, then reconnect to reconnect (my other laptop with XP has not this problem).

  I understand that there is compatibility between the BEFW11S4 v. 4 and Vista problems so I tried to update the firmware of dartybox.com and kept getting a message that failed. I hard rebooted the router but button of restart 30 seconds and the upgrade has always failed. I so re-set to factory settings through the online admin to the router, re-uploaded the implementation level and still got the emssage failed (I am sure that the model number & version is correct and I download the appropriate firmware upgrade).

  Is there anything else I can do another one) buy a new router; (b) living with school drop-outs; (c) remove Vista and go back to XP?

  Thank you

  Bigdank

  Genius! I have changed the name of code.bin, went to the admin > tab upgrade firmware and the upgrade file. I had a wireless without interruption ever since, even after the awakening of the laptop to sleep.

  Thanks for your help

• Jump and mix tracks after firmware upgrade?

  I can't explain it. Since the latest firmware upgrade Fuze my wife started jumping titles (for example jump to the next song to halfway through the current), but a funniest part - he mixes parts of files. We can listen to a song, and then all of a sudden he would be interrupted by 1 second of a file from a different album and then come back to play the first song from the point it was interrupted. What gives?

  Me that was too much.  I downloaded all my music back and reset my Fuze and reformatted it.

  Charge of excessive songs and back on went.

• Is the WRE54G compatable with the WAG54GS?

  Hello my client has a WAG54GS router and I just bought a WRE54G range extension to help its wireless network coverage. But I have since views information here and there on the possibility that these two devices are incompatible with each other.

  Could someone please confirm?

  Thank you very much

  v.much thank you for taking the time to answer

  It turns out that I got them to work together easily... updated the WAG54GS firmware to v1.01.03 then connected the WRE54G via ethernet to the WAG54GS and ran the WRE54G installation CD. Then I made the WRE54G has been placed in an appropriate place to receive the signal of the WAG54GS. Job done.

• Error on the UPS Firmware Dell Update utility

  Hello

  I got the error "No UPS connected or not able to make the connection" the inverter is connected by USB.  I have RS232 or USB enabled in the upgrade utility.

  I'm under UPS Local Node Manager, that's how I know that the UPS USB connection is good.

  Manager of local node said in respect of the power supply: Dell Rack/Tower UPS 2700W UPS RT LI LV 2700.  The device status for lack of UPS.

  The following information found here that I'm updating the firmware and then replace the battery followed by replacing the battery if the fault is not resolved.  I have re-sitting and replace the battery with a new battery.  The front panel of the inverter shows again the fault as well as the software after replacing the battery.  It seems that the update of the firmware is the only option for this error at this stage of troubleshooting.  However, the upgrade utility does not work.  Please help.

  Sometimes they have the management software will not allow the firmware update utility to try and work as follows:

  1. If the inverter has the NMC (Network Management Card) installed, then select the NMC in the utility of upgrade of the UPS Firmware and update the firmware of the UPS.
  2. Connect the ups to another system (server, desktop computer, laptop computer) that has neither ULNM nor would save installed. Load the utility to upgrade the Firmware of the UPS and the UPS firmware on the new system files. Launch the UPS Firmware Upgrade utility and update the firmware of the UPS. Reconnect the ups to the original system.
  3. Uninstall the ULNM and/or would save the system. Launch the UPS Firmware Upgrade utility and update the firmware of the UPS. Reinstall ULNM and/or save. Check the configuration settings.