Problems starting after installing memory

Similar Questions

• HP PAVILION HPE h8-1192d: could not start after installing new graphics card

  I recently bought a Gigabyte GTX 750 Ti Black Edition to replace my old. But it will not start after installing on my h8-1192d, and stuck on the screen flash hp. Help, please!

  Hello

  NVIDIA GTX 7xx or 9xx series graphics cards will not work in your PC.  The BIOS in "chicago" mothererboard is not compatible with the video BIOS in the graphics card.  You will need to get an older card chart such as the one of the below listed OEM HP graphics cards. Depending on the graphics card, you may need to replace the power suplly.

  

• iPhone 4S.  Stuck on request to post a link to iTunes.  Has started after installing the recent software update.  Tried to turn but the iTunes link keeps coming.

  iPhone 4S.

  Stuck on request to post a link to iTunes.

  Has started after installing the recent software update.

  Tried to turn but the iTunes link keeps coming.

  You can not connect the phone to iTunes as requested?

• Failed to start after installing the new memory module Equium A60

  I have an Equium A60 laptop with the following specs:
  P4 3.06 GHz
  256 MB Ram (including 64 MB ATI graphics card)
  30 GB HD
  Windows XP Home Edition

  The problem is the following; I bought a bar of memory in order to update my system. I bought a Kingston SO-dimm pc2100 512 MB. After installation of the memory of the laptop wouldn't start, after about 5 seconds after having turned it on, it turns off completely.

  If I remove the memory it starts up fine. I had tested memory and its ok so there seems to be a problem with the laptop itself. I'm confused, so if anyone has an idea of what might cause boot failure, I would be happy to know.

  Thank you very much...

  As far as I know the main reason for the failure of start is the use of non compatible modules.

  According to the specifications of the laptop, you must use PC2700 512 MB (PA3312U - 1 M 51). If you want to buy the module Kingston (products of very good quality) check it please the Kingston MEMORY SEARCH

  Good bye

• Satellite A60-672 does not start after upgrading memory

  Hello

  I bought an additional memory for my laptop, but after installing it the PC will start is no longer, when I turn it on it makes a brief noise then nothing. After taking the memory expansion out again once, the laptop still does not start.

  Peter

  Hello

  I agree with "guy sos." There is no doubt motherboard problem now. I assume you used the incompatible memory module.

  In any case, contact the after-sales Service of Toshiba partner in your country and explain to them the situation. The address that you will find under http://www.csd.toshiba.com/cgi-bin/tais/su/su_gaspLocator.jsp?pf=true

  Good bye

• Problems galore after installing the Vista SP2

  Once I installed SP2 on my Acer 6920 g, my sound card no longer works. I followed the "Fix It" solution and update its drivers, which solved the problem and his return. When I stopped the machine, he started rebotting, begin a strange "xp" mode, before launching Acer Arcade Deluxe, a media programme. This problem for about two hours, stop, reboot in this program can close again in a loop on and on. Through to hold the power button on the laptop, I managed finally to get the machine to stay 'off '. The following day, when I turned on the laptop I found that repairing the system has been launched, but could not solve the problem, telling me that the problem was the following;

  Event problem name: StartupRepairV2
  Problem signature 01: AutoFailover
  Problem signature 02: 6.0.6000.16386.6.6001.18000
  Problem signature 03:6
  Problem signature 04:524296
  Problem signature 05: 0xf4
  Problem signature 06: 0xf4
  Problem signature 07:0
  Problem signature 08:2
  Problem signature 09: WrpRepair
  Problem signature 10:16385
  OS version: 6.0.6000.2.0.0.256.1
  Locale ID: 1033

  Can anyone help? I have an option for 'Complete restoration of Windows', but want to this only as a last resort because I do not have a backup of my files.

  Thank you

  Try this first before reinstalling.

  If it fails, see below, data recovery before reinstalling.

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work, try to make a Bootable ERD to do a Startup Repair:

  As is the case with most computers/laptops these days, they do not come with good Vista disc to repair only the recovery disks.

  As your grave in the category above, download the ISO on the provided link and do a repair of the disc.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  You can make a tool to restart system, System Restore, etc. with it.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista repair disc.

  You can do a system restart tool, system, etc it restore.

  There is not a disk of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1 in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon.

  Mick Murphy - Microsoft partner

• Satellite C670 problems start after upgrade of Windows 10

  Hi all

  I made an upgrade of Windows 10 but after that my notebank satellite C670 has problems starting. It is always after the Windows updates were installed. It displays the logo of Win, followed of a blue screen. After several ignitions and extinctions I can once again the password login screen. Have already reinstalled Windows 10 because I did not come to the login screen more. But the problems are still there with ignition and extinction attempts it works. But this isn't a solution. You have ideas - drivers for Win10 or bios? Thanks for help

  Hello, I have the problem of the grandmother after the installation of Windows 10 I have nothing white screen
  Impossible to do a spanking Granny restore F8 or F12 nothing to do
  If someone gives you the solution I'm interested
  Thank you, CDT

  
  Validation has been translated by Google Translator

• Computer OS used to start after installing windows 10

  Hello im having problem starting my system after installing windows 10. I did the install and it worked fine since the upgrade to 8.1. But then I tried to format the drive and in the menu format, he's stuck at 2%, and then I restarted the computer. Now it will hang at the hp logo and go back to the same logo. Do I have to replace my hard drive?

  What I understand, if you have completed the 10 Windows Installer and everything has happened until the end, then you are supposed to be able to do a clean install with the download of Windows 10 DVD or USB.  With a working computer, GO to THIS PAGEand scroll down to the button "download tool" selection the 64-bit version.  Once clicked, it will ask you if you want a DVD or USB for the iso.

  Once it's done and you have the DVD or the USB version, see if you can install Windows 10.  If this fails, you may need to replace the hard drive.

• Satellite A200 PSAEOE does not start after upgrading memory

  Hi, I am first time here.

  I bought a Toshiba A200 PSAE0E-03J02JDR with 2 GB of RAM. I bought a pair of ram Corsair (2 * 2 GB VS2GSDS667D2). The computer does not start after that I installed the memory. I have intel 945 chipset, which is capable of 4 GB (manual page 1-2). The bios version is 1.8 2007.

  Can anyone help me, please.

  Post edited by: Marian ovidiu

  Hello

  The A200 series supports different chipsets;
  Intel 945 PM
  Intel 945GM
  Intel 943GML

  As far as I know your laptop supports the * 943GML * Intel chipset and the chipset supports 2 GB RAM max.
  Take a look at your laptop s user manual * Page 18.*

  Summer: 4 GB of RAM are not possible, and therefore your laptop does not start.

• Does not start after installing new video card

  Hello, I have a desktop H8-1284, and the video card went a few days ago. So I bought a video card Geforce GTX 650, and after installing the card and the computer starts, it hangs just at the start of the HP logo screen. So I put an old geforce 8800, and she starts without a problem. When I try the new card Geforce GTX 650, the same thing, just hangs at the splash screen.  I checked the bios and it doent seem to be something there that can help wouild. My diet is 460 w, and the new map needs of 400 w, any help will be greatly appreciated

  Hello

  Most of the cards PCI-E 3.0 are retro-compatible with the PCI-E 2.0 slots.  However, in order to get the PCI-E version 3, you must use a processor Ivy Bridge.  Look at these specificationsfor a typical NVIDIA GTX 650.

• Windows 7 takes 15 min to start after installing Labview 2012

  Hello

  I need help on this, is this a bug?

  The problem is that on my laptop after installing Labview 2012, it takes about 15 minutes to start, this happens every time a restart or start my laptop.

  At first I thought something with my laptop, but then my colleague also installed Labview 2012 on his laptop and has exactly the same problem, the difference is that his new laptop and is running windows 7 Professional 64-bit, mine is older and is currently running windows 7 32-bit professional.

  I tried to disable the services NOR, but has not solved the problem, but when I disable all windows services that start at startup, the startup is fast.

  Also note that I had Labview 2011 installed before and I didn't have this problem before.

  Tried also to find something in the registry, but nothing.

  Any who have this problem, or a solution to this?

  Thanks in advance

  This problem seems to be resolved, but then he come back again a few days later

  I did many tests in my laptop and found it to be in the "Service of Network Store Interface" service (INS). Disabling this service, you have your problem solved, but there is another problem, you lose the network.
  This happens because the "DHCP Client" service depends on the national statistical institutes.

  Also, this issue seems to occur only when the PC is in a domain and I'm in a windows server (Windows SBS2008) domain.

  Then I found that if you set manual this services which depend on national institutes of statistics (DHCP Client, DNS Client, IP Helper, network connections, local awareness network) and also put INS manual
  You must also disable the "Workstation" service that also depends on national institutes of statistics (why turn off? Because there are 3 services that depend on the workstation service, they will require to start, and then it will force NSIS to start, then long boot, if you really need of the dependent services on workstation, do the same as for them)
  Not also need uncheck this services in msconfig window if they are checked, and then the PC will boot normally without a network.

  When you start, you should go to services and start the DHCP Client for the network (and the other if you really need)
  This will force also NSIS to start and other services that depend on the national statistical institutes.
  The first time the PC restarts, you may need to reset these services to manual in the services window, I had to do, and then in sebsequent boots, they have been already set to manual
  If you leave right on the dependent services in automatic or automatic (delayed start) it will force NSIS to run and start time will go to + - 15 min

  Because you must manually start "DHCP Client" for the network, here's a solution to do it automatically after have connected you:
  1 - Go to control panel, and then open administrative tools
  Task 2-open Scheduller
  3. on the right click "Creat fundamental task.
  4. in the first window give a name ("DHCP" for example) and press next
  5 - Click on "When I Logon" and press next
  6 - click on "Start a program", and then press next
  7. in the "program/script" insert: net
  8. in the "Arguments" insert: start "DHCP Client".
  9 - Press 'Finish' and you're done

• Computer does not start after installing vista sp2.

  When the computer is turned on it presents two options: start windows normally or start the system restart. If start windows normally is chosen, it just reloads the same screen, if launch startup repair, it tells me that it can't solve my problem and returns me to the same screen as well. F8 or help options advanced.

  Free unlimited installation and compatibility support is available for Windows Vista, but only for Service Pack 2 (SP2). This support, initially planned to end on November 26, 2009, has been extended until February 26, 2010. Availability of support chat or messaging differs depending on your location. Some questions may require that more support for which he is advanced a charge.  Go to http://support.microsoft.com/oas/default.aspx?prid=13014&gprid=582034 & select appropriate category (i.e., download problem;) Installation problem; ( Problems after installing a service pack). ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Windows Vista does not start after installing Linux OS

  original title: Windows Vista does not start after the installation of the Linux OS... Help!

  I installed Fedora 10 Red Hat Linux on my HP laptop and now each time it powers on, I can't do vista windows at startup.  Goes directly into Linux.

  I need to get back to normal.  Any help would be appreciated.

  I installed Fedora 10 Red Hat Linux on my HP laptop and now each time it powers on, I can't do vista windows at startup.  Goes directly into Linux.

  I need to get back to normal.  Any help would be appreciated.

  Hey Oscar Jose

  Download the correct ISO file and make a disk bootable from the link below

  Then use the Startup Repair option when you start from

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  or at startup press F11 to start the process of restoration of hp and see if you can reinstall vista from the recovery partition and place your machine, back to the way you bought

  warning you all data loss and 3 third-party programs that you have installed unless there is a non-destructive option in your hp recovery options

  Thirdly try to ask in a fedora forum to solve the problem, he has caused

  http://fedoraproject.org/

  Walter, the time zone traveller

• Problem starting after the installation of the NTI Echo Satellite P50-B-11V

  Hi guys. I have problems to start mid laptop computer (Toshiba Satellite P50-B-11V, F04236S) after the installation of NTI Echo3 to migrate the data from the drive HARD original to a new SSD (Toshiba 480 GB Q300 series).

  Error: file/echo not found boot/initrd.gz. Pilot pata-platform...
  Kernel panic not syncing VFS: Don't mount rootfson unknown - black (0,0).

  Anyone facing this problem? Please advice if you have the time.
  I tried several times to repair Windows (F12 key) and I have tried different ways to migrate data but the problem even after reboot.

  Thanks fo your time.

  Posted by marianbur
  

  Hi guys. I have problems to start mid laptop computer (Toshiba Satellite P50-B-11V, F04236S) after the installation of NTI Echo3 to migrate the data from the drive HARD original to a new SSD (Toshiba 480 GB Q300 series).

  Error: file/echo not found boot/initrd.gz. Pilot pata-platform...
  Kernel panic not syncing VFS: Don't mount rootfson unknown - black (0,0).

  Anyone facing this problem? Please advice if you have the time.
  I tried several times to repair Windows (F12 key) and I have tried different ways to migrate data but the problem even after reboot.

  Thanks fo your time.

  Dear marianbur,

  New laptop having same problem here, is now stuck... Have you received still no solution?

  Greetz

• Dell Vostro 200 does not start after installing the SP2 for Windows Vista Business

  I have to keep which dates back to the system restore to get my computer on the road.  Whenever the update is installed I don't get past the first Screen Microsoft with the arrows.  Now, my computer is very slow and I have not been able to install SP2. I need very simple instructions I'm no computer expert!

  Free unlimited installation and compatibility support is available for Windows Vista, but only for Service Pack 2 (SP2). This support, initially planned to end on November 26, 2009, has been extended until February 26, 2010. Availability of support chat or messaging differs depending on your location. Some questions may require that more support for which he is advanced a charge.  Go to http://support.microsoft.com/oas/default.aspx?prid=13014&gprid=582034 & select appropriate category (i.e., download problem;) Installation problem; Problems after installing a service pack). ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft