Problems with fax after loading software
I had my HP 4500 for awhile. Never had any problems with the fax. A few days ago I finally loaded the software that comes with it, and now my fax machine doesn't seem to be able to receive. The rings of the machine about 5 or 6 times, it seems that this connection is, but whenever I get "failed"...
Any suggestions would be greatly appreciated!
Hi suzduell,
Follow the steps outlined in the document below.
http://support.HP.com/us-en/document/c01956630
Tags: HP Printers
Similar Questions
-
problems with rv042g after the software upgrade
After the software upgrade it reboot the router on every 45 seconds
I tried this tool from Cisco RV0xxV3_FirmwareRescueUtility_v4.0.0.7 Web site without success, the problem is there, is one way that you can get the router up and running again?
Can I run a TFTP server and download new software, or I ther a FirmwareRescueUtility for rv042g?
Mogens Demmark
The first firmware comes with RV042G is 4.2.0.03, so the firmware utility rescue v4.0.0.7 would not work.
Given that your will to power cycle automatically RV042G every 45 seconds, and the problem has not disappeared after that you did a reset to factory default, the unit needs a new firmware downloaded. Please, try the following steps.
1. disconnect the power cable to the unit.
2. hold the reset (using a paperclip) button, while plugging in the power cable.
3 look at the DIAG LEDS.
4. release the reset button when you see the DIAG led are flashing.
5. a flashing DIAG indicates that the unit runs in start mode, and a server tftp on the device is waiting for a picture of fresh firmware to the address 192.168.1.1.
6. set up your PC with an IP address in the subnet 192.168.1.x, e.g. 192.168.1.100 and specify as default gateway 192.168.1.1.
7. try to ping the unit with 192.168.1.1, and you should see a response from the unit.
8. run a program client tftp (with a command line) and push an image good firmware, for example
TFTP-I 192.168.1.1
If the procedure above does not resolve the problem, contact the support center for RMA.
-
Problems with sound after loading Windows 7 Ultimate
I just loaded Windows 7 ultimate on my HP Pavilian m7100y. I have no sound, the monitor is an HP vs19c and trendy top speakers. Can someone please.
Hello:
See if this driver works...
Accept the agreement, download and install the first driver on the list if you have installed W7 32 bit, second driver on the list if you have installed W7 64-bit.
-
seems I'm not the only one having problems with safari after update 9.3 cannot follow the links. Safari blocks. hope it gets fixed quickly. jaa shooting allows to follow the link, but the Web page is not out of good old days. any oher ideas?
The 'list' of relevant articles that I know, they are now
-You can read about the problems in the present statutes and possibly find workaround solutions, particularly in the last
Apple iOS suspension 9.3 updates for older devices, work on activation fix | IVous
Apple launches new version of iOS for iPad users 9.3 2 affected by bricking bug | 9to5Mac
If you are unable to activate your iPad 2 (GSM model) update to iOS 9.3 - Apple Support
Leave a post by: ChitlinsCC
-
Problems with WiFi after put 10.11.2 up-to-date.
Mid 2011 iMac. Problems with WiFi after put 10.11.2 up-to-date. No associated network. Everything was fine before the update. All the pre 10.11.2 device works fine. Anyone else having issues? I have to disconnect and reconnect manually. WiFi drops every 5 to 10 minutes. Nothing has changed on the machine something of the update.
Please do not comment on the age of the system. Achieve a Mid 2011 arrived at a possible replacement point. I have many other new Mac at home. The Mid 2011 is spec'd with 16 GB of RAM, i7 and SSD. It's always very fast.
Thank you in advance for the answer...
Hi Captainsniz
There are a few things to try. Keep doing this until the problem disappears.
First of all, if you have not already, shut down the computer completely, wait about 1 minute, then restart.
Disconnect the wifi network either via system preferences, either by pressing the "Option" key and clicking on the wifi menu bar icon.
Reset the DHCP lease by going to system preferences > network and show Advanced Options, and then click the button to "Renew the DHCP lease" TCP/IP tab.
You can delete the wifi network of system preferences > network > network name... then close system preferences. Then reopen and add the network in.
You can also restart your wifi router, it erases the old connections. Most of the routers you just turn off and wait a few minutes, then restart. You can also reset your ISP modem if you have a.
Finally, you can try to reset the PRAM and SMC on your Mac. I'll get this info here on Apple Support KBs for your particular Mac.
Be sure to back up your computer.
Hope this helps, Greg
-
Problem with the method. load()
Hello
I have a problem with the. jquery load().
In my composition, in compositionReady, I use. load() to load a file external html in a regular element of edge - no problem here.
The loaded HTML code contains a div id = 'spot' - I would like to clik top and pull a comand edge, such as 'play symbol' or 'move this item '...
the problem is: How can I contact this div?
I tried variuos solutions:
$("spot")
sym.getComposition () .getStage (). $("spot")
... and mix a lot...
I originally thought to write something like
{$("spot").click (function ()}
Alert ('clicked spot.');
})
Thank you for helping me!
This will not work because the loaded html file is completely external to the project dashboard animate. Elements in this external file, example #spot, is not 'really' connected to the edge project lead.
Hope this makes some sense.
Darrell
-
Problems with mail after switching to macOS Sierra
Hey all
After having recently upgraded to macOS Sierra, I am unable to read my mail.
I get the following error every time I check on "Get Mail".
There may be a problem with the mail server or the network. Check the account settings "*" or try again.
The server returned the error: Mail could not connect to the server 'pop1.tribcsp.com' using SSL on the default ports. Verify that this server supports SSL and that your account settings are correct.
What does this error message mean and how can I solve this problem.
Thank you
Hi Michael,
I see your message that you get an error in the mail indicating that there is a problem with the mail server or the network. To help get this problem resolved, I suggest that you follow the steps below:
If mail refers to a problem with the mail server, or the network
Mail will say that it is impossible to connect due to a problem with the mail server or the network. For example, the message may refer to a connection that has expired, or too many simultaneous connections:
If you are connected to the Internet, but the connection has expired, your email provider might be affected by a discontinuance of service. Contact them or see their status Web page to ensure that their e-mail service is online. Examples of status pages:
- iCloud mail status
- Gmail status
- Status of Yahoo mail
- Status of the AOL mail
- Status of Outlook e-mail
If the message indicates the number of simultaneous connections, too many of your devices is check your e-mail account at the same time. Quit Mail on one or more of your other devices.
If you are still unable to send or receive e-mails
- Make sure that you have installed latest version of the Mac software updates, especially if the problem occurred immediately after the installation of a previous update.
- In OS X El Capitan or later version, you can see a status icon and the short error message in the upper right of the Mail window, under the search box. The message may indicate 'Network offline' or 'Connection failed', for example. Click the message to see more details on the issue.
- Check your connection to the Mail connection doctor. It might be able to say more on the issue.
If you cannot send or receive e-mail on your Mac.
Take care.
-
Big problems with fonts after upgrade to Yosemite
Hello
I upgraded my macbook pro to Yosemite for more than six months and since then, I have serious problems with application of fonts in browsers and many software I use. I googled the problem over and over again and nothing seems to help.
In general, these are the main symptoms of the problem with screenshots:
1 system ads are gibberished, or better yet, appearing with something like that, instead of letters:
2. bold letters does not at all (when I use gmail, for example) or leads to an illegible font change:
3. hyperlinks symbols on Web sites or webmail applications simply appear as empty squares and there is no way of knowing what you click on.
Bottom line: before turning to the last option and the resettlement of Yosemite, if someone could help, I'd be more than grateful.
< image edited by host to remove the serial number >
You probably have a lot of fonts installed garbage. Follow these steps to recover your Mac for only the fonts installed in OS X.
(1) open the book fonts and choose restore fonts Standard menu. All third-party fonts will be moved out of the system and root of the fonts in the library files in a new folder next to each named (deleted) Fonts.
2) click on the desktop so Finder is the name of the app next to the Apple logo in the upper left corner. Hold down the Option key and choose go > library. This will open your user account's library folder. Create a new empty folder on the desktop. Open the folder fonts in your user account. If there is something in it, move them to the new folder on the desktop.
3) restart in Mode safe mode by rebooting and hold down the SHIFT key. When you reach the office (you need to log in Mode without failure), restart normally. Among other things, this erases all the cache files on the account of the user logged in Mode safe mode and resets the database of book of fonts for this account.
(4) clear all remaining the system font cache files. Close all the running applications. From an administrator account, open the Terminal application and enter the following command. You can also copy and paste from here in the Terminal window:
sudo atsutil databases - remove
Terminal will then ask your admin password. When you type, it will not show anything, so make sure you enter it correctly.
This command removes all the font cache files. To the system and the current connected to the user account. After you run the command, close Terminal and immediately restart your Mac.
Now test. With only fonts available provided OS and all data policies implemented cache and other such parameters cleared and reset, fonts should appear correctly in the system.
-
HP laptop - 15-r150nm: problem with wifi after update realtek adapter
Hello! I've updated some drivers of HP customer service and then restarted computer. When it is on I couldn't use wifi. When I select the problems, it says: 1) "" Realtek 802.11B/G/N WIFI adapter RTL8723BE has some problems to the program control or hardware. "" (it is Croatian, so I tried to translate it for you)
(2) "a network cable is not plugged in correctly or may be broken.
What should I do, I have only this laptop and internet wifi, write this work? Thank you!
Hi @frane53nja,
Welcome to the HP Forums!
This is a wonderful place to find answers and advice!
You have the best experience in the HP forum, I would like to draw your attention to the Guide of the HP Forums.
I understand that your laptop works OK and after updating drivers on reboot HP customer service, you have lost your wireless network. When you run the Windows troubleshooting tool, you received a message that there was a problem with the NIC due to recent hardware or software changes.
Here is a link to HP PC - troubleshooting wireless network and Internet (Windows 8) that should help you.
Before you perform a restore, as shown in the above troubleshooting steps, you can try this option.
Go to the nursery of the device
Click the network tab to expand the list.
Right-click on the wireless network adapter and select roll back driver.
Repeat this process for all types of adapters listed.
While on this screen please check this definition also.
Right click on the wireless adapter and choose Properties.
Click the power management tab. If "allow the computer to turn off this device to save power" is checked, please remove and click OK. Repeat this operation for all types of adapters listed.
Please let me know the results.
Thank you for your participation in the Forums of HP! We want to help you as well as others who may encounter a similar problem as you. Please consider tagging the post in order to solve your problem as "accept as Solution" to help other members of the community!
To show recognition for my efforts please click the Thumbs Up below.
-
problems with sound after installing windows 7
My sound/audio does not work on my HP Pavilion dv2023tu notebook after a clean installation of windows XP.
The convenience store said there is a problem with the driver, but I can't find a new driver through windows update, and HP does not either for my model. The device installed on my laptop is called high definition Audio Device. Can anyone help, if not, where can I download the drivers from. It is better to buy driver update software to help locate the right driver?
Hello
A lot of Vista for Windows 7 drivers, so try the following.
Download the Audio driver from the link below and save it to your desktop.
FTP://ftp.HP.com/pub/SoftPaq/sp34001-34500/sp34387.exe
Once the download is complete, right-click on the Setup program and select "Run as Administrator" to launch the installation. If the driver installs successfully, restart the computer and check your audio files.
Kind regards
DP - K
-
Problems with sidebar after logon
Hello
We use the Windows with Windows Server 2008 Std R2 DC field. We currently have several offices of Vista that belong to the domain. DNS is configured as suggested by Ms. recommended and there is no other group policy in use than the default domain policy.
After logon successful sidebar does'nt load completely (sidebar is displayed, but the clock is not displayed). Also, if you try to start Office MS Word it stuck in the loading screen. If you don't expect anything happens. Strange thing is that all other programs will be load normally (even other Office programs), but Word and Sidebar are stuck.
All this happens completely random. You can open a successful session of 3 times, but then it happens again.
This problem came just after computers, where joined to the domain. The proglem didn't happen while that computers in the workgroup.
No idea what could be wrong?
Please repost your question to the Discussion Windows Server group to: http://www.microsoft.com/communities/newsgroups/en-us/default.aspx?dg=microsoft.public.windows.server.general&cat=en_US_9741c575-ec92-42f8-85ba-00dfe1483cf5&lang=en&cr=US where the Windows Server experts will be happy to help you. The fact that the Vista machines worked are in a working group suggests that the probllem is from the domain which means from the server.
I hope this helps.
Good luck!
Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
Smartphones from blackBerry Curve 9380 - battery drain after loading software updated BlackberryID
I have a Blackberry Curve 9380 with software v7.1 2931 Bundle (v7.1.0.1098) when you open the browser of th, I had "unhandled exception: the bridge has been destroyed." I loaded the latest (software BlackberryiD
net_rim_bbid_daemon v7.3.1.11) and this fixed the problem of browser, but battery now from 100% to 0% in about 4 hours. Previously a full charge lasts about 3 days.
Someone encountered this or can recommend a solution?
Thank you
Chris
CHRISALIS wrote:
Someone encountered this or can recommend a solution?
CHRISALIS, try this first... with your 9380 connected to the wall charger and BlackBerry power, remove the battery and reinsert it to restart. This will often reset the battery meter on the device (which over time can become out of sync with the actual load of the battery). You may need to try this over a few times the next day and the next.
Don't let not your battery to flow all the way to 0-10%, top it off during the day when you can, even for 15 minutes.
-
Problem with the bulk loading IOM account to AD
Hi all
I'm doing a loading block account for AD in IOM. I followed all the steps in the oracle documentation.
I entered the user in the format of CSV file data. Data in the example are given below:
Primary data in the Table:
UD_ADUSER_UID, UD_ADUSER_FNAME, UD_ADUSER_LNAME, UD_ADUSER_ORGNAME, UD_ADUSER_BNUMBER, UD_ADUSER_OBJECTGUID
TWoods, Tiger, Woods, "' 22 ~ CN = Users, DC = gkidmsolutions, DC = com", B000004, 104 "
TCruise, Tom, Cruise, "" 22 ~ CN = Users, DC = gkidmsolutions, DC = com ", B000005, 105"
WSmith, Will, Smith, "' 22 ~ CN = Users, DC = gkidmsolutions, DC = com", B000006, d149e9add00198469b1ebef579911024 "
Data in the Child Table:
UD_ADUSER_UID, UD_ADUSRC_GROUPNAME
TWoods, ' 22 ~ CN = users, CN = Users, DC = gkidmsolutions, DC = com ".
TCruise, ' 22 ~ CN = users, CN = Users, DC = gkidmsolutions, DC = com ".
WSmith, ' 22 ~ CN = users, CN = Users, DC = gkidmsolutions, DC = com ".
All of these users are already available in both IOM and AD. I am trying to establish links between these users through loading bulk. I am able to load bulk account using the IOM bulk load utility. After loading bulk accounts, when I go to the tab the user resources, I see a user resource AD for the respective users with the status 'Configured'.
However, the problem is when I try to update any user information through the process of the object resource AD shape, this not updated for AD. An exception mentioned below can be seen in newspapers. Looks like the loading block creates a map that can be seen from front end, but in fact, he is not pointing the user to the AD. Am I missing something? Help me!
*********************************************************************************************************************************************
"Current execution LOCKUNLOCKADADAMUSER
Target class = com.thortech.xl.integration.ActiveDirectory.tcUtilADTasks
< 5 April 2012 5:18:54 CEST > < error > < OIMCP. A/d converters > < BEA-000000 > <>=
< 5 April 2012 5:18:54 CEST > < error > < OIMCP. A/d converters > < BEA-000000 > < com.thortech.xl.integration.ActiveDirectory.tcUtilADTasks: unlockADUser: the user could not unlocked >
< 5 April 2012 5:18:54 CEST > < error > < OIMCP. A/d converters > < BEA-000000 > < =.
>
< 5 April 2012 5:18:54 CEST > < error > < OIMCP. A/d converters > < BEA-000000 > < = start the Stack Trace = >
< 5 April 2012 5:18:54 CEST > < error > < OIMCP. A/d converters > < BEA-000000 > < com.thortech.xl.integration.ActiveDirectory.tcUtilADTasks: unlockADUser >
< 5 April 2012 5:18:54 CEST > < error > < OIMCP. A/d converters > < BEA-000000 > < String index out of range:-1 >
< 5 April 2012 5:18:54 CEST > < error > < OIMCP. A/d converters > < BEA-000000 > < Description: String index out of range:-1 >
< 5 April 2012 5:18:54 CEST > < error > < OIMCP. A/d converters > < BEA-000000 > < java.lang.StringIndexOutOfBoundsException: String index out of range:-1
at java.lang.String.substring(String.java:1931)
at java.lang.String.substring(String.java:1904)
at com.thortech.xl.integration.ActiveDirectory.tcUtilADTasks.unlockADUser (unknown Source)
at com.thortech.xl.integration.ActiveDirectory.tcUtilADTasks.lockADorADAMUser (unknown Source)
at sun.reflect.NativeMethodAccessorImpl.invoke0 (Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
to com.thortech.xl.adapterGlue.ScheduleItemEvents.adpADCSLOCK_UNLOCKUSER. LOCKUNLOCKADADAMUSER (adpADCSLOCK_UNLOCKUSER. Java:163)
at com.thortech.xl.adapterGlue.ScheduleItemEvents.adpADCSLOCK_UNLOCKUSER.implementation(adpADCSLOCK_UNLOCKUSER.java:61)
at com.thortech.xl.client.events.tcBaseEvent.run(tcBaseEvent.java:196)
at com.thortech.xl.dataobj.tcDataObj.runEvent(tcDataObj.java:2492)
at com.thortech.xl.dataobj.tcScheduleItem.runMilestoneEvent(tcScheduleItem.java:2919)
at com.thortech.xl.dataobj.tcScheduleItem.eventPostInsert(tcScheduleItem.java:553)
at com.thortech.xl.dataobj.tcDataObj.insert(tcDataObj.java:604)
at com.thortech.xl.dataobj.tcDataObj.save(tcDataObj.java:474)
at com.thortech.xl.dataobj.tcOrderItemInfo.eventPostUpdate(tcOrderItemInfo.java:374)
at com.thortech.xl.dataobj.tcDataObj.update(tcDataObj.java:664)
at com.thortech.xl.dataobj.tcDataObj.save(tcDataObj.java:508)
at com.thortech.xl.dataobj.tcTableDataObj.save(tcTableDataObj.java:2906)
at com.thortech.xl.ejb.beansimpl.tcFormInstanceOperationsBean.setProcessFormData(tcFormInstanceOperationsBean.java:710)
at com.thortech.xl.ejb.beansimpl.tcFormInstanceOperationsBean.setProcessFormData(tcFormInstanceOperationsBean.java:426)
at Thor.API.Operations.tcFormInstanceOperationsIntfEJB.setProcessFormDatax (unknown Source)
at sun.reflect.NativeMethodAccessorImpl.invoke0 (Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at com.bea.core.repackaged.springframework.aop.support.AopUtils.invokeJoinpointUsingReflection(AopUtils.java:310)
at com.bea.core.repackaged.springframework.aop.framework.ReflectiveMethodInvocation.invokeJoinpoint(ReflectiveMethodInvocation.java:182)
at com.bea.core.repackaged.springframework.aop.framework.ReflectiveMethodInvocation.proceed(ReflectiveMethodInvocation.java:149)
at com.bea.core.repackaged.springframework.aop.support.DelegatingIntroductionInterceptor.doProceed(DelegatingIntroductionInterceptor.java:131)
at com.bea.core.repackaged.springframework.aop.support.DelegatingIntroductionInterceptor.invoke(DelegatingIntroductionInterceptor.java:119)
at com.bea.core.repackaged.springframework.aop.framework.ReflectiveMethodInvocation.proceed(ReflectiveMethodInvocation.java:171)
at com.bea.core.repackaged.springframework.jee.spi.MethodInvocationVisitorImpl.visit(MethodInvocationVisitorImpl.java:37)
at weblogic.ejb.container.injection.EnvironmentInterceptorCallbackImpl.callback(EnvironmentInterceptorCallbackImpl.java:54)
at com.bea.core.repackaged.springframework.jee.spi.EnvironmentInterceptor.invoke(EnvironmentInterceptor.java:50)
at com.bea.core.repackaged.springframework.aop.framework.ReflectiveMethodInvocation.proceed(ReflectiveMethodInvocation.java:171)
at com.bea.core.repackaged.springframework.aop.interceptor.ExposeInvocationInterceptor.invoke(ExposeInvocationInterceptor.java:89)
at com.bea.core.repackaged.springframework.aop.framework.ReflectiveMethodInvocation.proceed(ReflectiveMethodInvocation.java:171)
at com.bea.core.repackaged.springframework.aop.support.DelegatingIntroductionInterceptor.doProceed(DelegatingIntroductionInterceptor.java:131)
at com.bea.core.repackaged.springframework.aop.support.DelegatingIntroductionInterceptor.invoke(DelegatingIntroductionInterceptor.java:119)
at com.bea.core.repackaged.springframework.aop.framework.ReflectiveMethodInvocation.proceed(ReflectiveMethodInvocation.java:171)
at com.bea.core.repackaged.springframework.aop.framework.JdkDynamicAopProxy.invoke(JdkDynamicAopProxy.java:204)
to $Proxy341.setProcessFormDatax (Unknown Source)
at Thor.API.Operations.tcFormInstanceOperationsIntfEJB_h6wb8n_tcFormInstanceOperationsIntfRemoteImpl.__WL_invoke (unknown Source)
at weblogic.ejb.container.internal.SessionRemoteMethodInvoker.invoke(SessionRemoteMethodInvoker.java:40)
at Thor.API.Operations.tcFormInstanceOperationsIntfEJB_h6wb8n_tcFormInstanceOperationsIntfRemoteImpl.setProcessFormDatax (unknown Source)
at sun.reflect.NativeMethodAccessorImpl.invoke0 (Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at weblogic.ejb.container.internal.RemoteBusinessIntfProxy.invoke(RemoteBusinessIntfProxy.java:85)
to $Proxy178.setProcessFormDatax (Unknown Source)
at sun.reflect.NativeMethodAccessorImpl.invoke0 (Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at org.springframework.aop.support.AopUtils.invokeJoinpointUsingReflection(AopUtils.java:307)
at org.springframework.aop.framework.JdkDynamicAopProxy.invoke(JdkDynamicAopProxy.java:198)
to $Proxy337.setProcessFormDatax (Unknown Source)
at Thor.API.Operations.tcFormInstanceOperationsIntfDelegate.setProcessFormData (unknown Source)
at com.thortech.xl.webclient.actions.UserDefinedFormAction.editForm(UserDefinedFormAction.java:2033)
at sun.reflect.NativeMethodAccessorImpl.invoke0 (Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at org.apache.struts.actions.DispatchAction.dispatchMethod(DispatchAction.java:269)
at com.thortech.xl.webclient.actions.tcLookupDispatchAction.execute(tcLookupDispatchAction.java:133)
at com.thortech.xl.webclient.actions.tcActionBase.execute(tcActionBase.java:894)
at com.thortech.xl.webclient.actions.tcAction.execute(tcAction.java:213)
at org.apache.struts.chain.commands.servlet.ExecuteAction.execute(ExecuteAction.java:58)
at org.apache.struts.chain.commands.AbstractExecuteAction.execute(AbstractExecuteAction.java:67)
at org.apache.struts.chain.commands.ActionCommandBase.execute(ActionCommandBase.java:51)
at org.apache.commons.chain.impl.ChainBase.execute(ChainBase.java:191)
at org.apache.commons.chain.generic.LookupCommand.execute(LookupCommand.java:305)
at org.apache.commons.chain.impl.ChainBase.execute(ChainBase.java:191)
at org.apache.struts.chain.ComposableRequestProcessor.process(ComposableRequestProcessor.java:283)
at org.apache.struts.action.ActionServlet.process(ActionServlet.java:1914)
at org.apache.struts.action.ActionServlet.doPost(ActionServlet.java:463)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:727)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:821)
to weblogic.servlet.internal.StubSecurityHelper$ ServletServiceAction.run (StubSecurityHelper.java:227)
at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:300)
at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:27)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:57)
at com.thortech.xl.webclient.security.CSRFFilter.doFilter(CSRFFilter.java:78)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:57)
at oracle.iam.platform.auth.web.PwdMgmtNavigationFilter.doFilter(PwdMgmtNavigationFilter.java:122)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:57)
at oracle.iam.platform.auth.web.OIMAuthContextFilter.doFilter(OIMAuthContextFilter.java:108)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:57)
to oracle.security.jps.ee.http.JpsAbsFilter$ 1.run(JpsAbsFilter.java:111)
at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:313)
at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:413)
at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:94)
at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:161)
at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:57)
at oracle.dms.servlet.DMSServletFilter.doFilter(DMSServletFilter.java:136)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:57)
at weblogic.servlet.internal.RequestEventsFilter.doFilter(RequestEventsFilter.java:27)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:57)
to weblogic.servlet.internal.WebAppServletContext$ ServletInvocationAction.wrapRun (WebAppServletContext.java:3715)
to weblogic.servlet.internal.WebAppServletContext$ ServletInvocationAction.run (WebAppServletContext.java:3681)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:120)
at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2277)
at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2183)
at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1454)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:209)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:178)
>
< 5 April 2012 5:18:54 CEST > < error > < OIMCP. A/d converters > < BEA-000000 > < = end of stack memory trace = >
EXECUTEREMOTESCRIPT running
Target class = com.thortech.xl.integration.ActiveDirectory.tcUtilADTasks
"# SessionContainer:valueUnbound: expired Session of the name of the event is: Xellerate.Session.Looks like a problem with the value of the UD_ADUSER_LOCKED field. Change to retry and value non-zero.
-
Problems with scrolling after update
IM currently using the BlueJ ide and after updating to the new system / update (macOS Sierra) there is significant lag / jitter when scrolling. This problem only occurs when you use the scrolling with two fingers with the touch pad. When I use a mouse / or click the scroll bar on the side, it seems to go well. Not sure if there is a problem with BlueJ or the new OS. Would be very interested for some suggestions on how to fix this very annoying problem. (Using a Macbook pro 13, 2015).
Thanks a lot to all the answers
The obvious question would be if you see the problem of scrolling in Mac OS standard applications such as Mail, Notes and Safari.
If this isn't the case, it is likely BlueJ.
-
Serious problem with watch since the software update
Hello
I have a serious problem with my watch since to do the update of the software this morning.
Watch dial keeps flashing between the Apple logo, dial and access code.
Watch does not respond when you try to enter the access code or button does not not so can't turn off to try to restart.
I tried to disable pairing my iPhone 6s but watch be message saying "can't match Apple Watch - Activation lock could not be disabled on your Apple Watch because of a server error.
Nothing seemed abnormal during the update, I just let him do his thing.
Any help would be welcome.
With great thanks
Nicola
Hi Nicola
Try restarting your watch force: press and hold the side button and the digital Crown for about 10 seconds, until you see the Apple logo, then release them and expect the watch again.
Maybe you are looking for
-
What happened to the toolbar at the bottom
I added the add on https://addons.mozilla.org/en-US/firefox/addon/the-addon-bar/bar. However, he disappeared. I added it again, it said it was installed and it does not always show upward. Any thoughts?
-
Sat Pro 4200: needed 3D accelerator. How can I get?
I use the Toshiba Satellite Pro 4200. To play games as DirectX 8.0 must be installed. Games can not be installed because there is no "3D accelerator. What can I do? I have to admit that I am ignorant in this area
-
Many errors currupt files after the installation of Windows Live Essentials 11
I installed Windows Live 2011 and every since I had so many warnings to currupt files... drives me crazy!
-
How to stop sounds of keyboard on an Iconia Tab10 A3 A20FHD?
Prevents keyboard on an A3-A20-FHD sounds?
-
I have a 4025gz gateway with a broadcom wireless card. After I inatall drivers I get does not start code 10. Worked before I reinstalled windows. Windows xp service pack 3.