Problems with SLI on Y510P

Similar Questions

• Problems with my Lenovo Y510P.

  Hello Lenovo community!

  I bought my Y510P reconditioned 3 months ago and it had worked very well up until recently my laptop would just turned off and would not yet initialize for a certain period of time followed with my adapter it's a "pulsed" strange noise. I tried to remove my my laptop AC adapter and pressing the power on button, but it did not work. After 1 hour later I plug back my power adapter and the noise disappeared and it may start again, but with a strange event, my computer would be a smell of burning electronic and metal from the AC charger plug.

  I'm worried if it just my adapter is faulty or would it be a problem with my AC charger plug because it's the second time he has done that.

  your welcome, please make sure that the input voltage is the same amount that is stated on the laptop and secondly please keep me updated so that I know if your OEM charger worked

• Y510p problem with jack

  Hello

  A few days ago I bought the new y510p and I have a problem with headphones.

  When I put headphones jack slot after a few minutes, I can see message on the next connection and disconnection. It is to arrive at lasting a few seconds.

  Anyway, system, sometimes with micro when I never used this slot...

  Someone has an idea?

  Thank you

  Yes, I tried. It does not work on these drivers and others. Support of Lenovo in Poland said probably a manufacturing defect.
  It is probably a hardware problem

• Y510P problems with plug headphones

  Hello. Unfortunately, this is my first post on the forums of Lenovo.

  I bought Ideapad Y510P this week and here I first problem with it. This is a new computer, was only transported in the car, laid flat in his box. Today was the first day I tried connect headset.

  When I plug them in at bottom right part just works. The left side is all silent. When I try to hook them up slowly, only left side works until I plug them all way in and only the right side then gives sound.

  When I plug my headphones to halfway in (very difficult to achieve and the plug won't stay in all), both parties give sound properly.

  Tried it with 3 different working pairs of headphones.

  Check all the drivers (Realtek HD Audio) and it works. The work of speakers, wonderfully, only the headphone gives me problems.

  What could be wrong?

  I must say that I was pretty desperate.
  The laptop was taken instead I bought in and replaced by a new because it was within a week of purchase.

  The service said it was a problem "integrated", coming from the product being badly done.
  I wish I have a better solution for the Rangers, but the subject is now ready to be closed that I have a new thing.

• SLI problem with predator x 34

  Made on the top that I have to reset the native a ghost profile profile whenever I restart, but I also have to reset my prreferences SLI.

  On top of that if I choose the SLI in full glass applications, I'm fine. The monitor reports 100 Hz and I can play my games at 100 Hz.  Even though I'm playing games in windowed mode.

  If I turn it on to SLI in Full and Windowed mode, my monitor will show 100 Hz until I start a game in full screen or windowed mode.  At this point, I get only between 15 to 30 Hz, and of course, everything is very agitated.

  Once again this isn't a major problem that prevents me from doing what I want to do, but I wonder if it's just a driver problem that will be fixed after Acer and Nvidia work details or if it is a problem of monitor. My gut tells me that it is a driver issue, as the monitor can be defined and perform at 100 Hz.  The monitor just stays together at this resolution after reset and dislikes one of the options in the Nvidia SLI menu.

  Whatcha think?

  So I broke down and did a reinstall.

  Monitor came perfectly to 100 Hz, unique profile and not problems with the drivers of the monitor who came on their own good.

  So I think the problem is when you have had a previous installed monitor that had the capacity of more than 100 Hz, it can be a conflict or confusion.  Even uninstall this monitor or by reinstalling the drivers Nvidia has not fixed the problem, which means that the old monitor (s) was still present in the registry.  A reinstall of course removes all these potential conflicts, although I think that Acer should come with something different through software or at least documentation potential issues.

  Right now, everything is in place, works perfectly through several reboots.

• enable sli on y510p

  How can I enable SLI mode my dual graphics GT750M on the mobile Y510p. GPU - Z says THAT SLI is disabled. Can't seem to find a place to put on the Nvidia Control Panel either.

  Poster 2 GT750m Device Manager works correctly.

  so I update the drivers from nvidia. Had the same problem you second card shows up with error code 43. Driver problems, that's what I got when I was looking for.

  Apart from that, I have updated the OS to win 8.1 Overview. Don't, don't. NVIDIA does not have SLI drivers for it. If I ever go back to any return to a system restore. driver nVidia 311.41 version is the version that works right now with SLI.

  See if you can return to 311.41. This is the version that works for me. And I intend to keep it like that and not be updated.

• Satellite X 205-Sli3 - display driver would not correctly work with SLI

  I bought a computer to portable Satellite X 205 - Sli3 in the United States less than five months ago and I had a lot of problems with it lately.

  It happens quite often that the computer crashes without apparent reason, for example when I use Skype, Windows Media Player, or DVD player. Moreover, as quite often happens out of nowhere, I get a blue screen error and the computer shuts down. When this happens, Windows asks me to reboot if I want to search an online solution, and he tells me that there is a problem with my NVidia display driver. I tried to reinstall the most recent available on the Toshiba site display driver (which is since last September, however and therefore not very up-to-date), but problems continue to persist.

  Because of the driver problem, I am also unable to use the NVidia SLI technology, because whenever I have try to activate, I get either a blue screen error or computer hangs momentarily followed by the message: "display driver stopped responding and has recovered. Display driver nvlddmkm stopped responding and has successfully recovered. » ??

  Finally, I can't put my computer into sleep or Hibernate. My guess is that it is also linked to the question of pilot.

  Help from anyone in this matter would be greatly appreciated.

  Best regards

  Martin

  Hi mate,

  sounds like a hardware issue. It would be wise to send the machine to the nearest service partner in your country because you won´t be able to fix it yourself.
  I guess it has something to do with the VGA card, or among the memory modules would not work as they should.

  I can give you a link to find the nearest service partner in your country and them just contact them to explain your problem:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_whitepaper.jsp?service=EU&WHITEPAPER_ID=0 000000871

  Welcome them

• Audio problems with Lenovo Y500

  Hello.I bought recently Y500 with SLI and I am very satisfied with this computer. Yesterday, I found strange problem which I believe is hardware problem. I made a short video of the problem because I'm not sure I can describe it so accurate.

  http://www.YouTube.com/watch?v=S6BEiHuJBfI

  I believe that something inside is not in contact with good and this causes the sound stop. The computer is new, and the only thing I improved is the mSATA SSD so I can install the operating system.

  Any ideas what may be causing the problem? IM in the USA now, but I'll come back in Bulgaria soon, so I can not have time to return the laptop to Lenovo, so I will try to solve the problem by myself. Thank you.

  I found the problem. The bolt on the motherboard against the wire was too close and he was able to penetrate the insulation of the cable. And when the wire touches the ground (bolt metal), arrest him speaker.

  http://imagizer.imageshack.us/v2/800x600q90/706/473J.jpg
  http://imagizer.imageshack.us/v2/800x600q90/23/ajbg.jpg

• How to boot from USB DVD Rom on Y500 with SLI?

  I have problems starting a DVD from my laptop Y500 SLI. The DVD - RW rom is connected by USB and I do not see in the BIOS, but boot USB is enabled. Is it possible for a start of it on the y500 with sli? How? When I turn on the laptop that I can hear the cd loading, but it still goes to windows.

  Hi September,.

  Ishaan is correct since only today, I managed to get my hands on a Y500 to test. I have to admit that the Y500 is a great machine to own :-D

  In any case, with regard to get this to work, you will need to go into BIOS.
  To start the BIOS configuration utility:
  1 turn off the computer.
  2 press the Novo button (small button with the curved arrow, located next to the receptacle) and select Configuration of the BIOS.

  > Go to the tab "BOOT".
  > Under"Boot" change into "Legacy support".
  > Press F10 and save the setting.
  > Machine will restart and boot press F12
  > When the boot menu appears, select desired boot.

  Hope this helps and post your results.

  Concerning

• problems with, phone, 6, Bluetooth kit, Nissan, after update, for, Rios, 1.0.2

  After the update to ios 10.0.2 - trying to use bluetooth to call my vehicle, it says: "this article is not in your phone book." How can I solve this problem?

  Greetings, joybelino1!

  Thank you for joining the communities Support from Apple! I can't wait to see that you are having problems with your Bluetooth in your car! The good news is that Apple has a great article that will help you with measures to try to resolve the problem. Read this article to gethelp to connect your iPhone, iPad, or iPod touch with your car radio. Even though he talks about problems with the connection, it also has the steps for other questions you may have once connected.
  
  

  If you use Bluetooth

  1. Consult the user manual of your car stereo to get the procedure to a Bluetooth device.
  2. On your iOS device, drag up to open Control Center, then press ontwice to turn on Bluetooth and turn it back on.
  3. Restart your iOS device.
  4. On your iOS device, Cancel the twinning of your car radio. On the screen of your car désapparier your iOS device and any other device. Restart your car and your iOS device, then pair and connect again.
  5. Update your iOS device.
  6. Install the updates to the firmware of your car radio.
  7. If you still not connect, contact Apple technical support.

  Have a great day!

• Anyone having problems with WiFi connectivity after upgrade to Sierra?

  I was wondering if anyone else knows issues with WiFi connectivity since the upgrade to Sierra 10.12? I have not had any problems with connectivity WiFi previously on El Capitan. Now I have regular randomly loose connectivity. My internet is cable and when it is connected I have a 100% connection. My details of iMac and I have used only 10% of my storage.

  

  No problem with my iphone 6.

  Hello AspDesigns,

  I understand that, since the upgrade to Mac OS Sierra, your Mac seems to have trouble staying connected to Wi - Fi. Fortunately the diagnosis built-in wireless can help identify the source of so much trouble.

  Search for Wi - Fi using your Mac problems

  See you soon!

• Problems with mail after switching to macOS Sierra

  Hey all

  After having recently upgraded to macOS Sierra, I am unable to read my mail.

  I get the following error every time I check on "Get Mail".

  There may be a problem with the mail server or the network. Check the account settings "*" or try again.

  The server returned the error: Mail could not connect to the server 'pop1.tribcsp.com' using SSL on the default ports. Verify that this server supports SSL and that your account settings are correct.

  What does this error message mean and how can I solve this problem.

  Thank you

  Hi Michael,

  I see your message that you get an error in the mail indicating that there is a problem with the mail server or the network.  To help get this problem resolved, I suggest that you follow the steps below:
  

  If mail refers to a problem with the mail server, or the network

  Mail will say that it is impossible to connect due to a problem with the mail server or the network. For example, the message may refer to a connection that has expired, or too many simultaneous connections:

  

  If you are connected to the Internet, but the connection has expired, your email provider might be affected by a discontinuance of service. Contact them or see their status Web page to ensure that their e-mail service is online. Examples of status pages:

  • iCloud mail status
  • Gmail status
  • Status of Yahoo mail
  • Status of the AOL mail
  • Status of Outlook e-mail

  If the message indicates the number of simultaneous connections, too many of your devices is check your e-mail account at the same time. Quit Mail on one or more of your other devices.

  If you are still unable to send or receive e-mails

  1. Make sure that you have installed latest version of the Mac software updates, especially if the problem occurred immediately after the installation of a previous update.
  2. In OS X El Capitan or later version, you can see a status icon and the short error message in the upper right of the Mail window, under the search box. The message may indicate 'Network offline' or 'Connection failed', for example. Click the message to see more details on the issue.
     
  3. Check your connection to the Mail connection doctor. It might be able to say more on the issue.

  If you cannot send or receive e-mail on your Mac.

  Take care.

• iMac 27 "mid-2011 - Intermittent problem with CPU fan running at full speed and sleep mode.

  Hello!

  My iMac 27 "has an intermittent problem with the CPU fan runs at full speed. Sometimes it happens at the time when I start it, sometimes only in my session, and sometimes only after a certain time. So does seem to be a problem of "heating".

  Second issue is with the mode 'sleep'. It may occur also at any time, at the start of the iMac, session, or after a certain time. But once he starts to go in mode 'sleep', when I wake up, it goes right back in mode after a few seconds and that it will continue indefinitely until I restart the computer.

  What could be?

  Please help me!

  4ntoine

  Here is my model of iMac:

  iMac 27 "mid-2011 model 12.2

  Intel Core i7 3.4 GHz

  AMD Radeon HD 6970M 1024 MB

  OS X El Capitan 10.11.6
  SMC 1.72f2

  Boot ROM IM121.0047.B23

  reset the SMC

  Reset the management system (SCM) controller on your Mac - Apple Support

• problem with playing the clash of clans

  I'm having some problems while playing the clash of clans on my 2 mini ipad screen does not seem to meet sometimes as if it was some sort of delay so I have to tap several times in order to use a filter or throw the troops on the battlefield.

  Hi Trinitygr,

  Thanks for posting in the Community Support from Apple! I understand that you are having problems with your iPad screen while playing a game. I like to play games on my iPad and I don't see how this could be a nuisance. I'm happy to offer assistance.

  Are you only had this problem when using the app clash of Clans, or does it happen in all applications? I recommend to start by following the steps described in this article:
  If an application you have installed unexpectedly closes, unresponsive, or does not open

  Take care!

• I'm having problems with an outdated Apple ID

  I have problems with updating Apps etc in my Apple account because he always asked an obsolete in sign.  How can I change this?

  Hello

  Go down to itunes apple ID Delete page homepage all ID and then add it back back.

  See you soon

  Brian