Program CC stuck on blue loading screen after installation

Similar Questions

• MacBook Air 2015 is stuck on the loading screen after installing the update.

  I installed the updates on my MacBook Air and when I restarted the loading bar would stay right in the middle. I used the disk utility in recovery 'first aid' my drive mode, it was fine. I tried to start in safe mode, but the loading bar cling just at the end I reset the PRAM, but nothing works. Help, please.

  * Loading Bar *.

  Reinstall El Capitan without erasing the drive

  Please make sure that you back up.

  1. Restart the computer. Immediately after that the chime hold down the command and R until the Utility Menu appears.
  2. Select disk utility, then click on the continue button.
  3. Select the withdrawal (usually Macintosh HD) entry of the volume of the list to one side.
  4. Click first aid icon in the toolbar. Wait until the button is active, then click it.
  5. Quit disk utility and re-enter the Utility Menu.
  6. Select Reinstall OS X and click on the continue button.

  Also, see this tip for user: basic steps for the OS X upgrade.

• iPhone 6 stuck on the loading screen after trying to restore

  I have the most recent iOS installed on my iphone 6. but I didn't just install it recently, it was a week or two he is a. and I woke today to the apple logo on my screen. nothing happened to my phone I can think of that would have caused the phone to stop working like that, except a few drops here and there minor. I looked everywhere online to try to find the problem and tried the recovery for the phone mode. I did what he said and tried the option to update before the restore option. of course the option to update ' t didn't work. the restore option was going well until he got to the part where the apple logo comes up with small loading spinning circle below it, once completed. It runs for a few seconds and freezes and move again. iTunes says that it 4013 and 4005 errors there. I tried to reinstall itunes and restart my computer to see if that helps, but nothing has changed. I have a PC, not an apple computer, if that helps at all. IM really scared that nothing will be saved on my phone, or im going to have to get a new phone. But if someone could help that would be great.

  Are you using non-Apple Chargers?

  In the absence of a bad fall, water damage or other physical damage, this phone could have a defective NAND chip or a chip of U2 failed to the Board of Directors.
  If you clicked on restore and restoration has started and regenerated your encryption keys - so yes you won't be able to recover your data.

  Just to rule everything - try a simple force restart - home for 10 seconds and power keys.

  If still not resolved, try a restore in DFU mode (as opposed to a restore in recovery mode).   Someone will post a link for restore DFU instructions - I have not very practical.

  If this does not resolve, then you need the help of a repairer.  Your option at Apple will be out of warranty replacement for $299.   Your independent repair option would likely be a repair at the level of the Board of directors by mail which means you would be without your phone for a week or two, unless you can find someone local who performs at the level Council quality iPhone repair.  I expect one not does difficulty no fresh solution at about $140 for this problem.  Note - continuation of independent repair could cancel your ability to do the out of warranty Exchange at Apple for $299, although I've never seen this happen.

  I'm sorry about what happened - what a drag

• Stuck on the loading screen after pressing download

  His pipe on a blue wheel after clicking on download on the creative cloud app page. It is just there for hours.

  https://ccmdls.Adobe.com/AdobeProducts/KCCC/1/OSX10/CreativeCloudInstaller.dmg

  Direct download

• After Effects are stuck on the loading screen

  Everytime I open after effects CC (the 2014 version) it starts to load, but then gets stuck on the loading screen that says "initializing MediaCore. I used the free trial version and it works perfectly, and the creative cloud says that the app is updated. Why does not open After Effects?

  Hang | Initialization MediaCore | Splash screen | After Effects, Premiere Pro

• Satellite T130 - stuck on the loading screen - new hard drive required

  After a message on the screen saying back up your hard drive, it will fail quickly and pressing F1 it seems so stuck on the loading screen. I'm not too good with computers. I just have to buy a new hard drive to get the laptop working again, or is much more complicated than that. My guess is this one.

  Thanks in advance for any help provided

  The first question is: did you create recovery media (USB key)?
  If do not do this if for a long time your HARD drive works OK. original recovery image is saved on the HARD drive, but you must have it USB backup that you can use to install if the disk needs to be replaced.
  Do it as soon as possible. More info on what you can read in s operating manuals.

  What to do with the HARD drive? In my opinion if long as it works it has no reason to panic. Use your laptop as usual. If you notice some performance or more error messages problems I think that you should replace it.

  Replacing the HARD drive doesn't have to be so problematic. HARD drive cover must be placed in the lower corner of your laptop. The smallest is RAM and cotyledon should be for the HARD drive. Check it out.

  Before do you that this is remove the battery and unplug your computer laptop AC adapter / CC.

  If you have no experience with such things please don't made some risky step. You can damage something.

• Windows 7 Boot stuck in the loading screen

  Hello

  I have an Acer laptop, I don't know really how and when it started there is 3 of us using this computer, but now when I open my laptop it get stuck in the loading screen "starting Windows." It is not frozen, it's just stuck there. And in order to enter the actual Windows operating system, I have to first press a key.

  It could be things possible cause?

  Here are some solutions I've tried based on my research on the Internet:

  1 uninstall Antivirus.

  2 reset the BIOS.

  3 chkdsk all discs in safe mode

  4 scannow command, he had errors but did not say what that

  5 edition msconfig and do a clean boot with no start-up of the thread and MS services only.

  I hope someone can help.

  Thank you

  Hello

  What button do you press; F1 or F2?

  If so, check if the Date and time is correct.

  If she is not and again become incorrect after reset correctly, then turn off machine, then turn again, it's a battery CMOS failed in the motherboard, the origin of the problem.

  See you soon.

• Skype is stuck on the loading screen!

  My Skype is stuck on the loading screen! I used to have this problem but I fixed it by reinstalling. I'm on version 7.25 (.0.106) and it does not stop. I have java to work on IE and updated manually.

  What firewall and Antivirus applications are installed on your computer?

• Get windows error blue screen after installation Service

  I'm getting error " PAGE_FAULT_IN_NONPAGED_AREA_ (nischifk.sys)" blue screen after installing the VISION acquisition software in my OS Windows 10.

  I tried to install GO twice and got the same error.

  Awating for your valuable review

  Hi piZviZ,

  Sorry to hear about installation problems going TO that appeal to you. I guess you use going TO February 2014 or slightly earlier - can you confirm? There was a problem with one of the components, NEITHER FlexRIO going to understand which caused this exact problem on systems with a UEFI BIOS. We have since fixed the problem. If that were the problem, here are a few options:

  (1) install GO without Support IMAQ i/o for all cards of the R series (1473R, 8237R, etc.). This means that the affected FlexRIO component will not be installed.

  (2) update to a newer version of GO - I think that going TO August 2014 f1 shoots in the FlexRIO patched component that could solve the problem. If you choose to upgrade, I would recommend just upgrading to the last GO, if you are capable of: going TO August 2015 f1

  (3) keep the version of going TO you and patch the component FlexRIO: How can I get a blue screen after installation OR FlexRIO 13.1?, NI FlexRIO 13.2.0 Patch détails

  I recommend just update to the latest going TO if possible.

  Kind regards

  Joseph

• First Elements 14 stuck on the loading screen

  He worked for a month until today. I add a title to my book trailer when it crashed. I tried to open it up and it gets stuck on the loading screen. It makes it never happened: loading ExporterQuickTimehost.pm

  I'm working on a Windows 10 HP Envy laptop.

  Any help would be greatly appreciated.

  Deidre

  Hi pascalou,.

  Can you please tell us what is the amount of memory that the application supports, by checking in the task-> process manager. Also, remember the name of the title which had caused the crash?

  Have you tried to reboot the machine and then try?

  -Odette

• HP ENVY m6 n010dx: HP ENVY m6 n010dx stuck on the loading screen

  I have another problem with my computer hp laptop. I'll give some general information, before I started having this problem.

  I was on my laptop, watching my email. I went to open a new tab and typed in "youtube.com" and the page will not load. After trying to have the research charge several times, I realized that I was getting nowhere. Then, I slipped on the computer left (being a touch screen, it would have to open the menu where I can restart the laptop). This screen never popped up (laptop was frozen) so I simply got the power button until the laptop is turned off. I then turned on the laptop back, and he began to start as usual. He showed the black background, with the blue hp logo and was spinning, white, loading icon at the bottom in the Center. However, he never went any further than that. It is not really frozen because the white loading icon turns without stopping. At this point, I tried to find what to do. I tried a reset (I turned off my laptop, took out the battery, unplugged the charger, which is held the power button for at least 15 seconds, put the battery in the back, plugged the charger back in and turned back on the laptop). After that, I'm always met the same loading screen hp, white spinning loading and all. Sometimes, under the white thing of loading are the words "Prepare the automatic repair" However, nothing happens.

  My laptop is a hp ENVY m6 n010dx (touch screen)

  The serial number is: [personal information deleted]

  Hello

  Error code 24 characters for short drive Self Test (DST) would indicate that hard is defective and must be replaced.  It is also compatible with the original questions that you describe.

  If your laptop is still under warranty, contact HP and arrange for the disk replaced - you can check the status of your warranty here.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  If you are out of warranty and would like a guide to replacing the hard drive yourself, let me know.

  Kind regards

  DP - K

• Stuck to blue invent screen

  I have a Windows Vista Home Premium. Whenever I turn it on it remains to the blue 'HP Invent' screen and if I click on the orders, he said nothing happens! It takes about 5 minutes until it finally starts. It's really annoying, since most of the time I need to do reports for school right now or well I lose focus and I have a little wee patience.  I'm the kind of boy who wants things right away. One of you could help me! I would really apreciate it!

  Hi PCUserPro,

  Thanks for posting in the Microsoft community!

  Did you make any changes before the show?

  What is the model number of the computer?

  Perform a clean boot and check.

  Put your boot system helps determine if third-party applications or startup items are causing the problem.

  See the following article in the Microsoft KB for more information on how to solve a problem by performing a clean boot in Windows Vista or Windows 7:

  Clean boot

  How to set up Windows 7 to start in a "clean boot" State

  http://support.Microsoft.com/kb/929135

  Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  I would ask to look you at the link below that you might find useful.

  Blocked on the HP invent boot menu computer

  http://h30434.www3.HP.com/T5/desktop-lockups-freezes-hangs/computer-stuck-on-the-HP-invent-boot-up-menu/TD-p/305531

  See also: computer stuck on the first screen

  http://h30434.www3.HP.com/T5/notebook-operating-systems-e-g/computer-stuck-on-the-very-first-screen/TD-p/252897

  Please report if you are still having the problem. I will be happy to provide you with the additional options that you can use to get the problem resolved.

• Stuck on the profile screen after Windows update

  After that a windows update last night, my computer is stuck on the profile screen and I can not connect.  By clicking on the icons for different accounts does not bring to the top of the login screen where I can enter a password. The screen just flashes and the wheel spins for a while and then comes back to the profile screen. I tried to boot into the different security modes but same thing happens and I can not connect. I also tried to fix the computer and restart at the last known good configuration under boot options with the same results. Short to reset the default settings that will erase all my data, (which may or may not work) is there another fix?  It seems that windows is starting up, but just the login screen appear so I can enter my password.  I have windows 7 Home premium version.

  Hello

  Please provide detailed information about your question. I appreciate the step by step troubleshooting, and pain that you have taken to resolve your problem.

  If the Panel username and password is not displayed during logon and the problem persists even in safe mode, then the question could be if there is a corrupted file system or some third party conflicts.

  I suggest that you want to run auto repair with installation media and see if it helps you repair system files. For the execution of the task, I suggest you to try the steps below and see if it helps.

  Method 1

  When you use the recovery environment (Windows RE) to troubleshoot startup issues, first try the Startup Repair option in the System Recovery Options dialog box. If this does not resolve the problem, or if you have additional problems manually, use the Bootrec.exe tool.

  Because you cannot start the computer, you may need to create a bootable Windows installation media, and then do an auto repair, and if this does not help then you try to restore your computer to the previous date.

  Note: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  If you are using Windows 7 and you have the product key and then the link provided below might help you to download and create installation media if you do not.

  Download Windows 7 Disk Images (ISO files)

  Method 2

  If the problem persists, try to rebuild the BCD by using the Bootrec.exe tool. To run the Bootrec.exe tool, you must start Windows recovery environment (Windows RE) . To do this, follow these steps:

  1. Place the Windows 7 installation disc in the disc drive, and then start the computer.
  2. Press a key when you are prompted. Select a language, a time, a currency, a keyboard or an input method, and then click Next.
  3. Click repair your computer.
  4. Click the operating system you want to repair, and then click Next.
  5. In the System Recovery Options dialog box, click command prompt.
  6. Type Bootrec.exe, and then press ENTER.

  See the following link for more information:

  How to use the Bootrec.exe tool in the Windows recovery environment to troubleshoot and repair startup issues in Windows

  http://support.Microsoft.com/kb/927392

  Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Kind regards

• my phone is stuck on the load screen

  I was just on my phone and it glitches so I pressed the home page and lock button to restart and now it is stuck on the load with the apple logo screen, and I can't do anything else that turn it off but when I turn back goes back to the load up screen.

  Put your iPhone into recovery mode as described here.  You may try to go into recovery mode more than once to succeed.

  If you are unable to update or restore your iPhone, iPad or iPod touch - Apple supports

• Satellite L675D: Blue error screen after upgrading to Windows 8

  Hello

  I recently updated my laptop to Windows 8 Toshiba and whenever I use it, after 5-10 minutes, I get a page of the Blue error screen and restart the laptop.

  The problem is really annoying.

  I discovered that if I plug the battery charger, the phone works normally, but I want to solve the problem correctly.

  What should I do?

  I m wondering about your model of laptop. What cell phone do you have exactly?

  Regarding your question:
  I would like to get this right, with the battery it works ok, but when the AC adapter is plugged, it crashes?

  What happens when you connect the front adapter from the laptop would be turned on?

  How have you installed the Windows 8? Move the laptop Win 7 to Win 8 or have you installed Windows 8 clean system?
  Are installed all the drivers Toshiba Windows 8?

  Another idea:
  Go to Windows 8 Device Manager and uninstall the device called compatible ACPI control method battery
  Restart the machine and check how it works.