PSC 2210 scan problems in windows 7

Similar Questions

• PSC 2210, scanning, and Mavericks

  Greetings,

  I am baffled by a problem with my HP PSC 2210 all-in-one device and the latest system of Mac OS X 10.9 (Mavericks).  I was able to print since the upgrade, but I am not able to scan. I have checked the software updates, reinstalled my printer through the system preferences/printers & drivers, but no analysis. The 2210 presents itself as a printer, but there is no available scanning function.

  Suggestions?

  Thank you

  Tim!

  I was just PM'ed by a colleague at HP who informed me that scanning from this printer is not supported by the Mavericks.  I'm sorry.

  You can try the VueScan software or a new printer.

• Problems scanning HP psc 2210 with osx 10.9

  When you try to open the digitization of the Mac, the PSC will respond with the message "scanning" interrupted in its control panel.

  First the "Open Scanner" button is activator and the Mac will show 'the scanner warms up' and the 'wait' message reads the PSC 2210. After a minute the Mac will show "Scan reports a fault" and the PSC will show "scanning is interrupted.

  NB. update has been performed and the function of the printer works. Do not work what is the problem.

  Found a solution to the problem under: Troubleshooting > OS X Lion mountain & OS X v 10.9 Mavericks v10.8 > repair permissions write.

• PSC 2210 all-in-one: PSC 2210 all-in-one with Windows 10: ok printer but the scanner does not work

  
  

  Hey @Manu37520,

  Welcome to the Forums of HP Support!

  I understand that you have some problems with the scanning of your PSC 2210 all-in-one printer to your PC for Windows 10. The printer has no drivers for Windows 10. You will need to use a computer with an operating system prior to analyze.

  Please let me know if that solves your problems. If so, please click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• Reinstall HP psc 2210 software in Windows 7, 64-bit error

  I came across a problem last week when trying to scan with my hp psc 2210.  Cannot open the HP Director and ended up uninstalling the software.  Reinstall everything, I received the following error message:

  Error 1904.Module

  c:\windows\sysWOW64\hpgwiamd.dll has no

  Register for HRESULT-2147024770.  Contact your

  support staff

  I deleted all my temporary files and tried to reinstall a couple of times and still the same error message.  Any help would be greatly appreciated.

  It's great! My grandfather worked for NASA too (one of the reasons why I ended up getting a minor in Physics).

  If you want a good all-in-one I would say something like the 6700 premium. Its price moderate, really efficient, easy to maintain and has all the features you would ever want to on a printer. It is very reliable, and I used a.

  And thank you for your patience and your diligence. I wish we could get this problem.

  If you think I've been helpful there is a star below my name on each of my posts that gives "Bravo", which is like a "thank you" on the forum. And if you feel that this problem is resolved, you can mark the post that solved it wants a Solution provided (at the bottom right of each post).

  Have a wonderful day!

• Scan PSC 2210 "warm-up."

  Hello.

  Product: PSC 2210 all-in-one

  Operating system: Windows 7 32 bit

  Error: Message "Warm up" when start scan

  Any changes to the installation program or system.

  It was not the first analysis of the day.

  When to start to do this scan, it just hooked up with this message.

  Looking around, I found an update of the firmware (HpAiOFWUpdate2_2.exe), which was supposed to solve the problem of "heat".

  It running, I get the message: "a connected and powered Hewlett-Packard all-in-one that could benefit from this update of the firmware has not detected."

  Since on Win7 drivers from WindowsUpdate, the original all-in-one software was not used, and it is one of the requirements for the firmware update utility.

  I don't have the original CD, and it is older than Win7, then, it would be probably useless anyway.

  Looking at, I found the installation wizard (hppiw.exe).

  He confirmed that the drivers were installed and asked to test the scanner. He failed.

  He also mentioned another tool, the "HP print and Scan Doctor" (HPPSdr.exe).

  It was able to detect the problem. He told me to unplug the power cord from the all-in-one device, plug it back, turn on and restart the computer.

  After the reboot, the doctor was there waiting for me to continue. He took the test again, and yet once it failed.

  End of the story.

  So, how can I update the firmware?

  Is there another way?

  Is there another solution?

  Thank you in advance.

  Rui Ferreira

  Hi again.

  Thank you for your response.

  Although connect it directly to the wall socket set to solve the problem, I don't have a party immediately, mainly because it would mean that I had a bad electrical problem.

  But the next day, the message "Warm up" come again once, even with the machine directly connected to the wall outlet.

  During this time, I tried to find other ways to work around this problem and found one that works.

  It goes like this:

  Before using the scanner through the computer, I do a direct copy of the scanner to the printer without using the computer. He's never complained and made the copy without need to warm up. After that, he does all the scans, I need because it's already hot.

  I now have to "Accept as Solution" while others may try my workaround.

  Kind regards

  Rui Ferreira

• Printing problems HP PSC 1210 since upgrading to Windows 7

  Hello

  Unfortunately, I have major problems since upgrading my PSC 1210 previously hassle to Windows 7 Professional (32 bit) on a Dell Latitude laptop.

  1. connect the USB cable from the system causes to restart almost 100% of the time. (Start with her already plugged the same result.) If it restarts not who does not necessarily mean that it will print. Although the USB connection is identified, the document does not print and gets stuck in the queue; by selecting either restart or cancel in the print queue does not delete it. Or turn off and unplug the printer. I have to restart my computer for him to clear, but it still doesn't work. Also, it gets stuck when I choose to print directly to the printer. More recently, I've only managed to print after closing of all the HP of the process in the Task Manager. (The same problem with restarting forced to plug in the USB cable happens sometimes when the analysis rather than printing).

  2. on the occasions I manage to do print documents, does not print black cartridge, despite having just replaced the cartridge and the perflecty black print on the test page.

  I hope you can help because it's incredibly frustrating and tedious, and I really prefer is not to have to replace what was until what Windows 7 a perfectly good printer!

  Thank you

  Olivia

  Welcome to the Forums of HP savemysanity,

  I see by your post that when the connection of the USB cable, the computer restarts, the print jobs stuck in the queue since the upgrade to Windows 7, the black is not printing from applications, but prints black on the self-test page. I can help you with this.

  Run all the updates of Windows on the computer. Updates Windows Installer in Windows 7

  I have provided a document through the steps to see if this will solve the problem.

  Print jobs are stuck in the print queue.

  Download and run the Print and Scan doctor. It will diagnose the problem and could solve it automatically.

  Run the System File Checker. This utility allows users to analyze and restore corrupted Windows system files.

  System File Checker: run sfc/scannow & analyze its logs in Windows 7 | 8.

  The chkdsk command or "Check Disk" utility is used in Windows to browse your entire hard drive and find problems.

  Run the Chkdsk utility.

  Try another port on the computer and another USB cable just to exclude.

  If the problem persists, would completely uninstall and reinstall the printer software.

  Uninstalling the printer software.

  Installation of the software of the printer in Windows 7 for a USB cable connection.

  There is no driver to download, drivers are drivers from Windows Update.

  What operating system go you to?

  If you need help, let me know.

  Good day!
  Thank you.

• PSC 2210 adjustable upward as a network to a Windows & XP PC printer?

  HP psc 2210 all-in-one

  C8658A

  1 PC running Windows 7 and 1 PC running XP can be found on the network

  [Personal information]

  Hi QuiltyKathy,

  The printer does support the USB connection to the computer. In order to print from another computer, you can use the sharing of printing to share the printer. See the following link to view you must share a connected USB printer from XP to Win 7.

  http://helpdeskgeek.com/Windows-7/XP-to-Windows-7-printer-sharing/

• Bought a new computer with windows 7. "psc 2210 all-in-one ' will not work with it....

  I have a psc 2210 all-in-one printer that I love. I bought a new computer with Windows 7 and I can't make it work. The HP site said that I don't have to download the drivers because windows 7 has already installed, but the main thing is that I can't make it work. Anyone, please help. My printer works perfectly and I can't afford to buy another. (I have a 64 bit)

  HP should contribute to this situation. I'm a loyal customer of Hp, but it's ridiculous that they do not create a driver to work with their printers.  All computers are coming with Windows 7.  HP please find a solution!

  I could get my HP PSC 2210 all-in-one to print!  I don't know exactly, because I've tried everything I could think of.  My son is a computer on which it has upgraded to windows 7 (64-bit) several months ago - he was able to successfully print on my printer immediately.   I just did an install complete (I bought the full version, not upgrade) to windows 7 (64 bit) - a couple of days and I'm finally to the point where I'm trying to connect printers.  Here is what I tried... again, I tried several things, although I've been in that general area...

  connect the printer to the computer

  go to the CONTROL PANEL--> Device Manager

  Click the arrow to the left of the IMAGING DEVICES (to be developed)

  RT click on printer PSC 2200 (should be listed under imaging devices)

  Select PROPERTIES--> DRIVER, then uninstall

  Select / tick "remove the driver for the device.

  the printer will disappear from the Device Manager (and peripheral Imaging also if it was the only selection)

  Unplug the printer to computer

  re - connect the printer to the computer

  Device Manager automatically updated (takes a few minutes, the screen refresh let until the yolk! disappears).

  Go to the control panel--> devices and printers

  Select printer PSC 2200, select Customize your printer, then the printed test page

  I hope that you will get a valid test page.  If this is not the case, another option I tried was:

  Through the above scenario.  When you get to the step "select PROPERTIES--> DRIVER, then uninstall" Select UNINSTALL directly from this menu (be sure to select/check "remove software pilot")

  Continue with the remaining steps above.

  I also tried 'Update Driver' of one of the previous screens above... I would like to know if you have a bit of luck!   I'm sorry that's not accurate.  Yet once, I tried everything I could think of, and something finally worked!  (I don't think I tried to 'Turn off the pilot')   Good luck! .........

  ).

• in Windows 7 How to check on HP PSC 2210 all-in-one ink levels?

  With Win 7 drivers (and), what is the way to check the ink level in a PSC 2210?

  Thank you!

  [Personal information] HE DIDN'T THERE HAS NO HP PRINT DRIVERS ALLOWED THE WINDOWS PLATFORM 7!  No, natta!

  Installation of the printer software in Windows 7 for wired USB (to READ)

  http://support.HP.com/us-en/document/c01796879

  'Introduction '.

  The drivers for your HP product are already included in the new Windows 7 operating system. You don't need to download the drivers to use the product . Simply connect the printer to your computer with a USB cable, and Windows Update automatically installs the driver for your product. »

• I have a problem with the HP psc 2210 all in one printer.

  My printer is an hp psc 2210 all-in-one

  All main buttons are flashing and the message on my reading of the printer (Remove and check cartridge) t - it means to clean?

  Hello

  Equip your number of printer model to this site of HP drivers and support for this information and follow the troubleshooting steps for it.

  http://WWW8.HP.com/us/en/support-drivers.html

  Or ask in the Forums of HP's Support.

  http://h30434.www3.HP.com/PSG/

  See you soon.

• PSC 2210

  I have a new HP Windows 7 Home Edition premium 32-bit, I connected my PSC 2210 and everything seems fine, which means that it prints and scans OK but I am unable to set the options of printing or print properties, click on these a small window appears and off immediately, can you please help. Thank you

  Hello I found an update, problem solved, thank you.

• M1212nf mfp scanning problem

  Scanning problem

  My printer recently started having problems with scanning.  I start a scan.  He is busy for a long time and then fails informing me that HP LaserJet Scan has stopped working.  When I type the guest Cancel Windows, the printer still displays the message "Scan to PC" forever.

  I tried everything, including the scanning print doctor PC, which fails also in the same way, reloading drivers, firmware etc.  Sometimes I get a message "unable to communicate with the printer.

  I can print and photocopy.  It is connected via USB.  No hardware problem does appear in Windows.

  Help?

  Hello

  A defective cable can affect much more than the impression, as scannign consumes much more energy to make the connection by comparing standard analysis printing.

  However, what happens when you try to scan from Windows Fax and Scan?

  I strongly suggest such a you already reinstalled the software and a bit checked any possibility that the relocation of the software already.

  Please let me know the results,

  Shlomi

• Big problem with Windows XP, IE8

  I have a big problem with windows xp. Many things do not work as they had passed him. For example the personal setting are not recalled from session to session. IE 8 does not funtion properly (icons on the desktop are re-arraged, toolbars cannot be deleted or I'm unable to load pages from the internet). Programs do not work, the files will not open. When I look at my hard C disk folders and files are hidden.

  Recently, IE has been upgraded to IE8 and I installed Norton 360 but I don't mean that they caused the problem. However, whenever the Norton scan executes a "error 8 506 421" stands up and says me that I have to uninstall and re install Norton.» But I lost the ADMIN privileges so I am not able to uninstall or go back to a restore point.

  I can't go in safe mode. Pressing F8 takes me to the quick screen C not the windows safe mode screen. I can't go in safe BOOT mode. INI or the other.

  If I switch to another user, everything seems fine but I don't have ADMIN privileges with this user to be able to make changes.

  Is this a problem with norton? IE8? A virus?

  Any thoughts will be greatly appreciated.

  Thanks in advance,

  Lost without a computer

  It sounds like you have a corrupted for your user to administrator user profile.

  You may be able to recover using System Restore to restore to a point in time before your problem.  Based on the F8 key, you bring in a command prompt window, try to start restoring the system to the command prompt by using the following procedure:

  "How to start the System Restore tool by using the option of safe mode with prompt theCommand in Windows XP"

  <>https://support.Microsoft.com/kb/304449/en-us >

  If this does not work, you can still be able to recover by performing a check disk to your command prompt window operation (after that you press the F8 key).  Enter the following command:

  CHKDSK c: /R

  If you are in the Recovery Console, it can simply begin, or you may need to restart before it will start.  Corrupt profiles are most often caused by the Corruption of system files, so a chkdsk operation should be performed little matter how you end up recovery.  Note that this can take a few hours to run.

  "How to perform disk error in Windows XP check"

  <>http://support.Microsoft.com/kb/315265/en-us >

  HTH,

  JW

• The problem with Windows update - automatic updates service won't start not (error 126)

  original title: the problem with Windows update

  Please help me to get Windows Update operational return.

  XP Media Center Edition, Version 2002, SP3

  Had a problem with "Generic host process for Win32 has encountered a problem and needs to close."  Follow-up of the instructions on this link:
  http://support.Microsoft.com/kb/931852

  Seems to have cleared the error message.  So far so good.

  However, now a Windows Update does not work.  Security Center Windows were told to go to control panel > system and use the Automatic Updates tab.  But, if I go to control panel > system, the Automatic Updates tab does not appear.

  I also went to the control panel > Services.  Tried to start the automatic updates service.  Received this error message: could not start the service automatic updates on Local computer.  Error 126: The specified module could not be found

  I already followed several instructions on this subject:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-windows_update/cannot-access-Windows-automatic-update-after/aeaec175-01f4-47ed-8F97-55b854af4220

  In the thread above, I was following the post on 30 August.  According to Option A, I completed step 5 for the uninstallation of McAfee Security.  At this time, my network card has stopped working.  On the recommendation of the officer, I posted to the Malwarebytes forum.  The officer determined Malwarebytes that I don't have a malicious software.  I ended up posting on forum McAfee to get my network card works again.  Then I reinstalled McAfee and start to run Windows Update.

  I started with Option A, step 8 to reset Internet Explorer using http://support.microsoft.com/kb/923737.  The difficulty it has worked very well.

  Then Option A, step 9 says reset Windows Update using http://support.microsoft.com/kb/971058.  When I ran the difficulty in default or aggressive mode, I got an error message saying: he cannot start wuauserv.  The message asks me to verify that the user has privileges to take this step.  Well, I checked through user accounts who am the only one user set up on this PC and I have administrator privileges.  Help me please run this difficulty or recommend another way to get Windows Update works again.

  [1]... looks like you are saying that my system is so wet that a clean install is the (only?) way to go.

  [2] if I do a clean install, not only what I need to reinstall Windows and all my applications, I also have to reinstall the drivers... Etc. ?

  [3] I think I have the disks supplied with the PC system. Is it better to use than to use the recovery partitiion?

  [4A]... is there a possibility that some of [my data are] infected?

  [4] preventing me from simply infect the whole PC again?

  A1. Yes, and it was my recommendation in August, too.

  A2. Yes.

  A3. Only not really well using the restore Partition hidden to make the "destructive recovery" will include all drivers, etc., that have been installed at the factory.

  A4a. Yes, a real possibility.

  A4b. You run at least three 3 tests on the backup data before restoring one (1) with your installed & updated up-to-date anti-virus application (for example, Microsoft Security Essentials) and two 2 with good reputation, free online scans (e.g., ESET;) Bit Defender; Kaspersky; HouseCall; (F - Secure).

  If you have saved your data on CD/DVD, the disc scanner. If you have backed up your data to a flash drive, SD card, or another external drive AND KB971029 is installed, analyze the drive.

  If you have any questions or need additional help, please start a new thread in this forum: http://answers.microsoft.com/en-us/windows/forum/windows_xp-system

  Once again, good luck!