Qosmio F10 does not accept my recovery cd

Similar Questions

• Qosmio F10 does not start system missing or damaged

  I have a Qosmio F10, and I use all the proper procedures for RECOVERY DVD-ROM PROUDCT.

  "I did all the necessary readers updates as well, but when I turn on the laptop came with an error message:" \WINDOWS\SYSTEM32\CONFIG\SYSTEM
  "Windows was not start because the following file is missing or damaged:

  So, now my computer with startup options start, but what that you choose the system starts again and again...

  What to do? Please, I beg you.

  Hmmm usually after using the CD recovery Toshiba, everything should work ok.
  I read on some computer expert sites that this problem could be linked to the hardware failure. The HARD drive or the module memory is possibly corrupt.

  I would first recommend formatting the entire HARD drive (remove also all partitions).
  Install the operating system again.
  If it does not solve this problem you could check if it is possible to install from the original CD of Microsoft XP.
  Further, you can see the memory modules. Try to remove one and use only one or replace it with a new one.

  But please note that these are just my suggestions and I m not 100% sure if these proposals will allow you to solve problems. In any case it s worth a try

• Computer HP laptop, does not accept the recovery disks and don't accpet Windows Vista upgrade (HomeP to ultimate).

  Apparently the upgrade does not recognize that Windows is on the drive, but cannot restore the original software as HP blocked their recovery disk. The recovery partition is there, but he cannot get starter.  The recovery disks have the original spirit operating system Windows - how can I get the upgrade to recognize?

  Hello

  an upgrade must be done from vista, NOT operating system by booting from the disk to upgrade

  as you have problems using the maunfacturers recovery process, upgrade disc etc., read what you may have hardware problems.

  If you have problems with the process of recovery of manufacturers, contact the manufacturer

  It's their recovery process not microsofts

• Qosmio F10 does not work after the recovery procedure

  Hi, I just bought the toshiba recovery dvd for my qosmio laptop f10, I put the dvd in and it goes through the process of recovery and complete 100% he then told me to remove the dvd, and then press CTRL ALT DELETE to restart the computer.

  In doing so, he gets to the screen were it tells me windows startup and then the screen turns white and flickers a couple of times, and then the computer phone re boots and don't stop doing that, I press the F8 key when it restarts to go save mode, but when it starts in mode it tells me that windows is not completely set and goes no further and tells me that I need to run put in place to new.

  I don't have a windows cd only toshiba dvd that should put my laptop back to factory settings.

  Can aynone help me before I have sound toshiba?

  Thank you.

  Hello

  It's not easy to say why it happens. Usually, the Toshiba Recovery CD should work properly and after any recovery procedure, the laptop should run without any problems.
  You suggested that you ordered this CD from recovery of the ASP.
  Do you have the right recovery CD? Check the description of CD.

  The other possibility is that the device has a hardware failure. In this case, you must contact the service of Toshiba. Sorry, but that's all I can suggest.

  concerning

• Qosmio F10 does not start

  Hello

  my partner has a laptop qosmio who appears to be dead. He used it apparently pink lines appears across the screen, and it was cut. He tested food that looks very good. He gets the lights coming but they do nothing and the computer shows nothing.

  It is said there is a /bios of motherboard failure and will cost £600.00 to fix. This sounds like the MB/Bios, or would be - this something less dramatic and less expensive?

  Thank you

  From your description, I assume that there is problem with graphics card. Unfortunately, graphics card is part of the motherboard and the entire motherboard must be replaced.

  By the way: what model of laptop Qosmio has your partner?

• Windows Vista does not accept my password (unchanged) but I have no recovery disk - Windows is already installed

  Hello

  As the title says after using my laptop without any previous problems, suddenly I can not connect on Windows Vista.

  I'm 100% sure that the password has not been changed, caps lock, shift, caps lock Num etc is not active.

  When I bought the laptop, Vista was already installed, so I don't have a recovery disk.

  Any help would be appreciated.

  Hello

  Microsoft prohibits any help given in these Forums for you help bypass or "crack" passwords lost or forgotten.

  This is the Information from Microsoft on the problems of passwords;

  You will need to borrow a Microsoft DVD from a friend, Recovery DVD a manufacturer without these special work options available.

  • http://support.Microsoft.com/kb/940765

  If you are unable to connect to Windows 7 or Windows Vista, you can use the Windows Vista System Restore feature, or the Windows 7 system restore feature.

  You may be unable to connect to Windows Vista or Windows 7 in the following scenarios:

  • Scenario 1: You recently set a new password for the protected administrator account. However, you don't remember the password.
  • Scenario 2: You type the correct password. However, Windows Vista or Windows 7 does not accept the password because the system is damaged.
  • Scenario 3: You delete a protected administrator account. Now, you cannot connect to another administrator account.
  • Scenario 4: You change an administrator account protected with a standard user account. Now, you cannot connect to another administrator account.

  Malware can also cause problems with passwords:

  Download, install, update and scan your system with the free version of Malwarebytes AntiMalware in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  And here's how to go in Safe Mode options; Select safe mode with networking from the list of options:

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  If the above does not fix it:

  Here are the different methods to reinstall Vista.

  There is no Windows Vista downloads available from Microsoft.

  You can contact your computer manufacturer and ask them to send you a set of recovery disks.

  They should do this for a small fee.

  To reinstall Vista using their recovery disk/s, you start from the 1st recovery disk they provide and follow the manufacturer's instructions to reinstall:

  You need to change the Boot order to make the DVD/CD drive 1st in the boot order:

  How to change the Boot order in BIOS:

  http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm

  "How to replace Microsoft software or hardware, order service packs and replace product manuals.

  http://support.Microsoft.com/kb/326246

  And if you have never received a recovery disk when you bought your computer, there should be a recovery Partition on the hard drive to reinstall Vista on how you purchased your computer.

  The recovery process can be started by pressing a particular combination of the key or keys at startup. (Power on / start)

  Maybe it's F10, F11, Alt + F10, etc., depending on the manufacturer.

  Ask them to the proper key sequence.

  Some manufacturers have more available Vista recovery disks.

  If this happens, you may need to try this instead:

  You can also borrow and use a Microsoft Vista DVD, which contains the files for the different editions of Vista (Home Basic, Home Premium, Business and Ultimate) must be installed. The product key on your computer / Laptop box determines what Edition is installed.

  Other manufacturers recovery DVDs are should not be used for this purpose.

  And you need to know the version of 'bit' for Vista, as 32-bit and 64-bit editions come on different DVDs

  Here's how to do a clean install of Vista using a DVD of Vista from Microsoft:

  "How to do a clean install and configure with a full Version of Vista '

  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  And phone Activation may be necessary when you use the above installation method.

  "How to activate Vista normally and by Activation of the phone '

  http://www.Vistax64.com/tutorials/84488-activate-Vista-phone.html

  See you soon.

• Get blue screen. Reinstalled by the use of the recovery. Install IE6. Tried to re - install IE8. Does not accept. See below.

  Get blue screen.  Reinstalled by the use of the recovery.  Install IE6.  Tried to re - install IE8.  Does not accept.  The installation of SP3.  However, restart blue screen causes.  Able to install IE8.  Installed without windows updates.  I tried windows update on leOutilsmenu.  Cannot display the page.  Error #0x8007043C.  Expect the blue screen on the next reboot.  What should do?

  Hi Steve,.

  First of all, you seem to be under the misconception that a response is a response. On ths forum, an answer is an answer if it solves your problem. In this case I clearly have not solved your problem, and you should review my answers to "uncheck" them.

  IE6 does not work with this forum, and forum owners do not seem to appreciate how much of a problem, it's for people to re-setup of XP. I doubt they'll do something, even if they are aware of this gap.

  Go to your real problem, you can try Microsoft's solution for the HP patch...

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=23751

  Please let us know how you go.

  Tricky

• Microsoft Office S & T edition 2003 trial does not accept the product key

  The installer does not accept my product key. If I download the CD I'm going to lose all the information?

  What?
  Why do you want to use the OEM key from the recovery with Microsoft Office CD?

  To my knowledge Toshiba does not deliver laptops with Microsoft Office, but with only with OneNote.
  This isn't the same thing, and you cannot use OneNote key with MS Office software.

• Re: Failed on nine L510 Vista admin password - does not accept the admin pass

  Hi all

  Completely baffled by this one so would appreciate any advice.

  I just bought a new Satellite L510 with vista hard disk installation.

  I went through the installation process long and eventually got to the point where I could configure my admin account and the name of my computer.

  I chose the name of my admin account and typed in the password and confirm the password and named my computer.

  Now when I get to the initial Vista logon screen, it does not accept the password I am entered (and confirmed).

  This can be a problem with caps lock, as the password was all numbers.

  (the password was all numbers and five numbers)

  It, however, gives the correct indication for the password that I entered. It does not accept the password.

  I would be happy even just redo the installation process, but I have no idea how to do this, because I can't even a quick command-line anywhere.

  Help, please!

  It's strange. You can log on using a different user name?

  In any case to run recovery, you either:

  * Press and hold zero during the power upward
  * Press F8 before Windows starts to enter the Windows Start Menu, then run recovery of the option "repair your computer". http://APS2.toshiba-tro.de/KB0/HTD9102IR0000R01.htm

• Qosmio Player does not not on Qosmio G30

  Hello

  I got my laptop to out of area using the Toshiba recovery cd and now the qosmio player does not work. I can not play music without having to start Windows.
  I looked in the drive of all programs-utilities Toshiba - qosmio and he says that file not found.

  Help, please

  Hello

  There is a CD that comes with your laptop called:

  For the Qosmio player recovery CD

  you have to start the laptop from this CD, in the same way that you used in the installation of the windows recovery

  and follow the instructions

  concerning
  _________________________

  Please don't forget to take a look here:
  http://forums.computers.Toshiba-Europe.com/forums/help.jspa?helpType=reward

• does not accept administrator passwork

  I am the administrator on my computer. He suddenly left accepting my password so that I can no longer log into my account on the computer or make changes. I don't have a password reset disk. Someone can tell me why it would suddenly stop taking my password and how do I access my account?

  Hello

  You may have a malware problem or your system is corrupt.

  Read and follow the steps mentioned here.

  Microsoft prohibits any help given in these Forums for you help bypass or "crack" passwords lost or forgotten.

  Here's information from Microsoft, explaining that the policy:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-security/keeping-passwords-secure-Microsoft-policy-on/39f56ef0-5d68-41AD-9daa-6e6019c25d37

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  And this is the Information from Microsoft on the problems of passwords;

  You will need to borrow a Microsoft DVD from a friend, if you do not, as Recovery DVD a manufacturer does not have these particular options work.

  • http://support.Microsoft.com/kb/940765

  If you are unable to connect to Windows 7 or Windows Vista, you can use the Windows Vista System Restore feature, or the Windows 7 system restore feature.

  You may be unable to connect to Windows Vista or Windows 7 in the following scenarios:

  • Scenario 1: You recently set a new password for the protected administrator account. However, you don't remember the password.
  • Scenario 2: You type the correct password. However, Windows Vista or Windows 7 does not accept the password because the system is damaged.
  • Scenario 3: You delete a protected administrator account. Now, you cannot connect to another administrator account.
  • Scenario 4: You change an administrator account protected with a standard user account. Now, you cannot connect to another administrator account.

  Malware can also cause problems with passwords:

  Download, install, update and scan your system with the free version of Malwarebytes AntiMalware in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  And here's how to go in Safe Mode options; Select safe mode with networking from the list of options:

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  See you soon.

• the new Win7 disc replacement does not accept the case key

  Our dv6 - 2173cl end is more the boot, the "freeze" while showing the wallpaper with the taskbar 'framework' as well as the Start button, the HP logo button and the Date/time.  Defective hard drives the check HP tools with 90772-50e656-xd0021(7? wrote down in a bit of a hurry, sorry)-6ou103 error code.  Since the reader would also not 'take' the restoration attepmts (so the HP tools) we thought that a new disc has been a given.  Fast forward...  Now with the new drive in and a new Win7 install (no recovery disk, yes we know) the facility does not accept the key from the sticker on the bottom of the case and Yes Win7 is Home Premium on old and new.  So now, what do we do to get active Windows?

  I found that if you enter the key during installation and enter the key during activation of this always accepts it. Always works for me when I do a clean install of Windows 7 on client computers.

• Windows does not accept my password

  For the last 3 days, windows does not accept my password.

  Hello

  Microsoft prohibits any help given in these Forums for you help bypass or "crack" passwords lost or forgotten.

  This is the Information from Microsoft on the problems of passwords;

  You will need to borrow a Microsoft DVD from a friend, Recovery DVD a manufacturer without these special work options available.

  • http://support.Microsoft.com/kb/940765

  If you are unable to connect to Windows 7 or Windows Vista, you can use the Windows Vista System Restore feature, or the Windows 7 system restore feature.

  You may be unable to connect to Windows Vista or Windows 7 in the following scenarios:

  • Scenario 1: You recently set a new password for the protected administrator account. However, you don't remember the password.
  • Scenario 2: You type the correct password. However, Windows Vista or Windows 7 does not accept the password because the system is damaged.
  • Scenario 3: You delete a protected administrator account. Now, you cannot connect to another administrator account.
  • Scenario 4: You change an administrator account protected with a standard user account. Now, you cannot connect to another administrator account.

  Malware can also cause problems with passwords:

  Download, update and scan your system with the free version of Malwarebytes AntiMalware in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  And here's how to go in Safe Mode options; Select safe mode with networking from the list of options:

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  See you soon.

• I can't connect to my user account name, and it does not accept my password.

  I can't connect to my user account name, and it does not accept my password.

  Hi Jillgatewood,

  You did a recovery password file? You can use it to reset your password. Unfortunately if you have lost or forgotten your password, you will need to consult this article KB http://support.microsoft.com/kb/189126/en-gb

• Vista does not accept the password (password not changed or forgotten)

  Vista does not accept the password (we have not forgotten password of windows startup) how can we get around this problem .the password has not been changed or forgotten Vista has a little programming problem which stops the right password

  It is most often caused by the computer being infected, so after you go back into the system, it would be wise to make an analysis.

  http://www.elephantboycomputers.com/page2.html#Removing_Malware

  You can change your password to something you remember (or use a white) another administrative user account. If you had only an administrative user account, all is not lost. You can then follow the general recommendations for implementing user accounts in Vista that I will give you at the end of this post.

  All this requires a certain level of computer skills. You know better and that take the machine to a competent local computer tech (not a type of BigComputerStore/GeekSquad place) is the best solution for you.

  If you have an installation of Vista DVD (not a recovery DVDs), you can start the system with it. Select the default language, then select "repair your computer". Then select "Command Prompt". At the command prompt, type:

  NET user administrator / Active: Yes [press Enter]
  NET user [insert here the name of your user account] [insert the new password of user as 1234 here] [press Enter]

  [Note: do not enter the brackets!]

  Remove the installation DVD and restart the computer. Now, you will be able to connect to your user account by using the password that you set; for example, 1234.

  If you do not have a Vista installation DVD (only have a recovery disk), the computer mftr. may have given you the option to repair Vista (not a system recovery!) system in the diagnostic menu. This menu of diagnosis is the same one where you can choose Safe Mode. Get to this menu by repeatedly pressing the F8 key as the computer starts. If you do not have this option, you can make a bootable Vista file repair DVD in this link:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Note: All the Neosmart recovery disk downloads are torrent files. There is a good explanation of the torrent on the site Web of Neosmart files. You will need a torrent as muTorrent client to get the files. Torrent client will download the .iso file with which to create the bootable DVD. You will need to use third-party burning software such as Nero, Roxio or the free ImgBurn (http://www.imgburn.com ) to burn the image .iso image file, not in the form of data.

  Once you have fixed things, log on to the additional administrative account you will be made by the suggestions below and disable the administrator account integrated yet for security reasons:

  Start Orb > Search box > type: cmd
  When cmd appears in the above results, right-click and choose "Run as Administrator" [OK]. Now, you will get the command prompt. At the command prompt, type:

  NET user administrator / active: No. [Enter]

  Exit the command prompt.

  General recommendations for creating users in Vista:

  You absolutely don't want to have only one user account. As XP and all the other modern operating systems, Vista is a multi-user system with integrated system of accounts as default Administrator and comments. These accounts should be left alone because they are part of the structure of the operating system.

  In particular, you do not want one account user with administrative privileges on Vista because the administrator account integrated (normally only used in emergencies) is disabled by default. If you use as an administrator for your daily work, and this account is corrupt, things will be difficult.  It is not impossible to activate the built-in administrator to rescue things, but there may be more that you want to do. Better not to put you in a bad situation at first.

  The user account that is for your daily work must be a Standard user, with the extra administrative user (call it something like 'CompAdmin' or 'Tech' or similar) only it for elevation purposes. As a user Standard is recommended for security reasons and will help protect your computer against infections. After you have created "CompAdmin", connect to it and change your normal user account Standard. Then log on to your regular account.

  If you want to go directly to the desktop and ignore the Welcome screen with the icons of the user accounts, you can do this:

  Start Orb > Search box > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).
  MS - MVP - Elephant Boy computers - don't panic!