Question 2-one-Site VPN
NetPro dear gurus,.
A router upstream with IOS 15 plays a role by not allowing s2s vpn
a 5520 ASA to pass through traffic. If this is the case, so how to solve this problem.
Concerning
Faiz
Nothing should be done to get through the VPN traffic regarding the licensing of fears on IOS 15.0.
If you actually cancel the IPSec VPN tunnel on the router IOS 15.0, then Yes, you would need security K9 license, but to cross the traffic, there is no additional license required.
Tags: Cisco Security
Similar Questions
-
2 one-Site VPN between HQ, Site A and Site B
Dear brothers,
Really I need your kindly help on Site 2 Site VPN.
We have a HQ and 2 Sites (Site A Site & B), and we think to set up VPN Site-2-Site between them now.
HQ--> 3845 router (will be the hub)--> a given vlan 11 & vlan voice 21
Site A--> router 2901 (will be the Spoke1)--> a given vlan 12 & vlan voice 22
Site B--> router 1941 (will be the Spoke2)--> a given vlan 13 & vlan voice 23
So my questions are:
1 - when the VPN going up, are only the HQ VLAN data & voice will be able to reach the Site & A B data & Voice VLAN and Vice versa?
2 - when the VPN is going up, are that the Site has data & Voice VLAN will be able to reach the Site B Data & Voice VLAN and Vice versa?
Thank you
Hello
I think this example explains what you need:http://www.cisco.com/c/en/us/support/docs/security-vpn/ipsec-negotiation...
Kind regards
Averroès.
-
2 one-Site VPN Cisco 2801 and with crossing NAT
Hi guys,.
I would like to configure two Cisco 2801 using IPSEC/IKE. Both routers are connected to the internet through DSL lines. The DSL line have RFC1918 address side LAN where routers connected to the internet face. I can do NAT on DSL modems.
Cisco IOS 2801 routers allow to configure site-2-site VPN with NAT crossing?
Here is a model of physics/IP configuration:
LAN<->2801 Modem DSL<-Internet->DSL modem<-Priv ip-=""> 2801<-Priv ip-=""><-> LAN
Thank you
Gonçalo
Yes, you're good to go only if one or both of the sites has an IP address which is natted with private IP address statically. The implementation of IPSec on SRI NAT support in most crosses so that shouldn't be a concern
->-Priv>-Priv>-Internet->-> -
question links to site 2 site VPN with authentication cert
Currently we are accumulate tunnel site-2-site VPN with our client. Usually we use pre-shared key as authentication with other customers without any problems, but it must use authentication cert with her this time. But the question is that our CA is different from theirs. I tried a few times, but he failed. Is it someone please let me know that he must have the certificate issued by the same certification authority to create the VPN tunnel?
Thank you very much!
Hello
You can read this document to get a simple example of setting up a VPN S2S using certificates on an ASA:
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080aa5be1.shtml
Basically the sides must have the same certification authority and If there is an intermediate certificate that must be installed also. The ASA 2 will generate a CSR (certificate access code request), now then PKI will create a certificate for both parties, commonly called "certificate of identity".
Please pass a note and mark as he corrected the post helpful!
David Castro,
Kind regards
-
Site to site VPN question: passing a public IP with IPSEC
Hi all
I need to create a VPN tunnel site to site using IPSEC between two offices on the Internet. The offices belong to two different companies.
They gave me a series of 16 public IP addresses. One of these IP addresses is used on the ISP router and this is the next hop for my router. Another IP in the range is used on my router? s external interface (which is a Cisco 851) and he is also my site VPN endpoint. So far so good...
Here's my problem: the IP source of encrypted traffic, is a public address from within the IPs public 16 I (not the one on my router interface). The actual application that needs to send the encrypted data is a server in my local network, and it has a private IP address. The other site, expects to receive data, however, the public IP address. I used NAT between the private IP address of the server and its public IP address, but no data goes through the tunnel. Moreover, the tunnel between the two end points established without problem. The problem is that the source of my encrypted data is the public IP address and I don't know how to get through the tunnel. I enclose my router configuration.
Any help is appreciated.
The access list "natted-traffic" should say:
extended traffic natted IP access list
deny ip host 192.168.0.160 BB. ABM ABM BD
deny ip host 192.168.0.160 BB. ABM BB.BE
output
I hope this helps.
-Kanishka
-
only one statement of site-to-site VPN remote network?
Hello
I wonder on in case of site to site vpn, we can define only a single declaration of network for the Branch Office peer network?
If there is a local network to peer site, then, how to set those for the local subnet peer?
Can anyone answer my question?
Thank you.
If I understand your question, wondering how to add a different subnet to an existing site-to-site VPN tunnel?
If that is correct, you can add this network to the crypto ACL of the tunnel at a site. But you have to demolish and rebuild the tunnel before it takes effect.
Once you have added the required configuration, run the following commands to shoot down the tunnel. Do not forget that this disconnects all users on the VPN, so it is best to let users know when you go to so that they are not connected at this time here.
ISAKMP crypto claire
clear crypto ipsec his
-
Client Vpn Cisco vpn remote site inaccessible (one site to another)
Hello
I configured two vpn with pix 515 cisco connection. One using a cisco vpn client and another another site to site vpn connectin with other pix.
I have my local network with 192.168.149.0 network, vpn clinet pool with 192.168.17.0 network and a remote site with 192.168.145.0.
Client vpn local network accessible and always remote site, but 192.168.17.0 (vpn client) 192.168.145.0 not accessible (remote site).
Plese help me!
Thank you
This scenario is possible with no v6.x, v7.x
the link below is an example of configuration:
-
Cisco ASA Site to Site VPN IPSEC and NAT question
Hi people,
I have a question about the two Site to Site VPN IPSEC and NAT. basically what I want to achieve is to do the following:
ASA2 is at HQ and ASA1 is a remote site. I have no problem setting a static static is a Site to IPSEC VPN between sites. Guests residing in 10.1.0.0/16 are able to communicate with hosts in 192.168.1.0/24, but what I want is to configure the NAT with IPSEC VPN for this host to 10.1.0.0/16 will communicate with hosts in 192.168.1.0/24 with translated addresses
Just an example:
N2 host (10.1.0.1/16) contacted N1 192.168.1.5 with destination host say 10.23.1.5 No 192.168.1.5 (notice the last byte is the same in the present case,.5)
The translation still for the rest of the communication (host pings ip destination host 10.23.1.6 N3 N2 not 192.168.1.6 new last byte is the same)
It sounds a bit confusing to me, but I've seen this type of configuration before when I worked for the supplier of managed services where we have given our customers (Ipsec Site to Site VPN with NAT, don't know how it was setup)
Basically we contact the customer via site-to-site VPN hosts but their real address were hidden and we used as translated address more high 10.23.1.0/24 instead of (real) 192.168.1.0/24, last byte must be the same.
Grateful if someone can shed some light on this subject.
Hello
OK so went with the old format of NAT configuration
It seems to me that you could do the following:
- Configure the ASA1 with static NAT strategy
- access-list L2LVPN-POLICYNAT allowed ip 192.168.1.0 255.255.255.0 10.1.0.0 255.255.0.0
- public static 10.23.1.0 (inside, outside) access-list L2LVPN-POLICYNAT
- Because the above is a static NAT of the policy, this means that the translation will be made only when the destination network is 10.1.0.0/16
- If you have for example a PAT basic configuration to inside-> external traffic, the above NAT configuration and the custom of the actual configuration of PAT interfere with eachother
- ASA2 side, you can normally configure NAT0 / NAT Exemption for the 10.1.0.0/16 network
- Note of the INTERIOR-SHEEP access-list SHEEP L2LVPN
- the permitted INSIDE SHEEP 10.1.0.0 ip access list 255.255.0.0 10.23.1.0 255.255.255.0
- NAT (inside) 0-list of access to the INTERIOR-SHEEP
- You will need to consider that your access-list defining the VPN encrypted L2L traffic must reflect the new NAT network
- ASA1: allowed to access-list L2LVPN-ENCRYPTIONDOMAIN ip 10.23.1.0 255.255.255.0 10.1.0.0 255.255.0.0
- ASA2: list L2LVPN-ENCRYPTIONDOMAIN allowed ip 10.1.0.0 access 255.255.0.0 10.23.1.0 255.255.255.0
I could test this configuration to work tomorrow but I would like to know if it works.
Please rate if this was helpful
-Jouni
- Configure the ASA1 with static NAT strategy
-
Question about ACL's with the 2621 when using site to site VPN
I set up two site to site vpn. We have an ASA at our headquarters and branches will IOS routers - one is a 1811 and the other 2621. Both are running the latest versions of IOS, respectively. The two VPN site-to-site do not work. I have a list of inbound on the external interfaces of both routers, access that allows only the IP address of the ASA IP traffic. All other traffic is denied. I put NAT overload upward in the typical form, and I use ip outgoing inspection on the same interface, to allow incoming traffic back to surfing the internet. This configuration works very well with the 1811, where all traffic is blocked except traffic IP (IPSEC) coming from the ASA. Guests at our headquarters can reach hosts behind the 1811 and vice versa.
Here's my problem: the 2621 is processing traffic encapsulated on the external interface and block this traffic because it does not match. I know because when I turn on logging / debugging on the 2621, I see inbound traffic blocked by the ACL. Technically, I guess that it does not, but to this interface, the traffic is always encapsulated so I think it fits to this access list and then go to the Cryptography decapsulation card and be sent to the destination host. Just as it does on the 1811. I have not 'wan' t to create another line in the access list for all subnets to Headquarters. Why is not it works the same way as it does on the 1811? Is there something else I need to activate?
------------------------------------------------------------------------
Config of 1811:
!
version 12.4
horodateurs service debug datetime msec
Log service timestamps datetime localtime show-timezone msec
encryption password service
!
hostname BranchVPN1
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 notifications
!
AAA new-model
!
!
AAA authentication login default local
activate the default AAA authentication no
authorization AAA console
AAA authorization exec default local
!
AAA - the id of the joint session
no ip source route
IP cef
!
!
IP inspect the audit trail
inspect the IP dns-timeout 10
inspect the name IP internet udp timeout 30
inspect the name IP internet tcp timeout 30
inspect the name IP internet ftp timeout 30
inspect the name IP internet http timeout 30
inspect the name firewall tcp IP
inspect the name IP firewall udp
inspect the name IP firewall icmp
IP inspect the dns name of the firewall
inspect the name IP firewall ftp
inspect the name IP firewall http
inspect the name IP firewall https
inspect the IP firewall name ftps
property intellectual auth-proxy max-nodata-& 3
property intellectual admission max-nodata-& 3
!
!
IP domain name xxxx
!
!
!
!
username xxxxxxxxxx
!
!
!
class-map correspondence vpn_traffic
police name of group-access game
!
!
VPN policy-map
class vpn_traffic
in line-action police 2000000 37500 pass drop exceeds-action
!
!
!
crypto ISAKMP policy 10
BA aes 256
preshared authentication
Group 2
ISAKMP crypto key address xxxx xxxxxx
ISAKMP crypto keepalive 10
!
life crypto ipsec security association seconds 28800
!
Crypto ipsec transform-set esp - aes 256 esp-sha-hmac xxtransform
!
xxmap 10 ipsec-isakmp crypto map
defined peer xxxx
Set transform-set xxtransform
PFS group2 Set
match the address tunnelnetworks
static inverse-road
!
!
!
interface Loopback0
172.16.99.1 the IP 255.255.255.255
!
interface FastEthernet0/0
Description Connection to Internet (DHCP)
DHCP IP address
IP access-group outside_in in
no ip redirection
no ip unreachable
no ip proxy-arp
inspect the firewall on IP
NAT outside IP
IP virtual-reassembly
automatic duplex
automatic speed
No cdp enable
xxmap card crypto
!
interface FastEthernet0/1
Description of the connection to the local network
address 172.20.1.1 IP 255.255.255.0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
IP virtual-reassembly
automatic duplex
automatic speed
No cdp enable
VPN service-policy input
!
interface Serial0/0/0
no ip address
Shutdown
No cdp enable
!
interface Serial0/1/0
no ip address
Shutdown
!
IP forward-Protocol ND
IP route 0.0.0.0 0.0.0.0 dhcp
!
no ip address of the http server
local IP http authentication
no ip http secure server
IP nat inside source list nat - acl interface FastEthernet0/0 overload
!
IP nat - acl extended access list
refuse any 10.0.0.0 0.255.255.255 ip
allow an ip
outside_in extended IP access list
allow udp any eq bootps host 255.255.255.255 eq bootpc
allow an ip host (ASA IPADDR)
deny ip any any newspaper
IP extended access list police
deny ip host xxxx any
deny ip any host xxxx
IP 172.20.1.0 allow 0.0.0.255 10.0.0.0 0.255.255.255
tunnelnetworks extended IP access list
permit host 172.16.99.1 ip 10.0.0.0 0.255.255.255
IP 172.20.1.0 allow 0.0.0.255 10.0.0.0 0.255.255.255
!
recording of debug trap
logging source-interface Loopback0
exploitation forest xxxx
access-list 160 note t is
not run cdp
!
!
control plan
!
Banner motd ^ CCAuthorized technician!
^ C
!
Line con 0
line to 0
line vty 0 4
exec-timeout 5 0
Synchronous recording
entry ssh transport
line vty 5 15
exec-timeout 5 0
Synchronous recording
entry ssh transport
!
Scheduler allocate 20000 1000
end------------------------------------------------------------------------
2621 Config:
!
version 12.3
horodateurs service debug datetime msec
Log service timestamps datetime localtime show-timezone msec
encryption password service
!
hostname BranchVPN2
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 notifications
no console logging
!
AAA new-model
!
!
AAA authentication login default local
activate the default AAA authentication no
authorization AAA console
AAA authorization exec default local
AAA - the id of the joint session
IP subnet zero
no ip source route
IP cef
!
!
IP domain name xxxx
!
IP inspect the audit trail
inspect the IP dns-timeout 10
inspect the name IP internet udp timeout 30
inspect the name IP internet tcp timeout 30
inspect the name IP internet ftp timeout 30
inspect the name IP internet http timeout 30
inspect the name firewall tcp IP
inspect the name IP firewall udp
inspect the name IP firewall icmp
inspect the name IP firewall ftp
inspect the name IP firewall http
Max-events of po verification IP 100
!
!
!
!
!
!
!
!
!
!
!
!
username xxxxxxxxxxxx
!
!
!
class-map correspondence vpn_traffic
police name of group-access game
!
!
VPN policy-map
class vpn_traffic
in line-action police 2000000 37500 pass drop exceeds-action
!
!
!
crypto ISAKMP policy 10
BA aes 256
preshared authentication
Group 2
ISAKMP crypto key address xxxx xxxxx
ISAKMP crypto keepalive 10
!
life crypto ipsec security association seconds 28800
!
Crypto ipsec transform-set esp - aes 256 esp-sha-hmac xxtransform
!
xxmap 10 ipsec-isakmp crypto map
defined peer xxxx
Set transform-set xxtransform
PFS group2 Set
match the address tunnelnetworks
reverse-road remote-peer
!
!
!
!
interface Loopback0
172.16.99.2 the IP 255.255.255.255
!
interface FastEthernet0/0
Description Connection to Internet (DHCP)
DHCP IP address
IP access-group outside_in in
no ip redirection
no ip unreachable
no ip proxy-arp
NAT outside IP
inspect the firewall on IP
automatic duplex
automatic speed
No cdp enable
xxmap card crypto
!
interface Serial0/0
no ip address
Shutdown
No cdp enable
!
interface FastEthernet0/1
Description of the connection to the local network
IP 172.20.2.1 255.255.255.0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
automatic duplex
automatic speed
No cdp enable
VPN service-policy input
!
interface Serial0/1
no ip address
Shutdown
No cdp enable
!
IP nat inside source list nat - acl interface FastEthernet0/0 overload
no ip address of the http server
local IP http authentication
no ip http secure server
IP classless
IP route 0.0.0.0 0.0.0.0 dhcp
!
!
!
IP nat - acl extended access list
refuse any 10.0.0.0 0.255.255.255 ip
allow an ip
outside_in extended IP access list
allow udp any eq bootps host 255.255.255.255 eq bootpc
allow an ip host (ASA IPADDR)
deny ip any any newspaper
IP extended access list police
deny ip host xxxx any
deny ip any host xxxx
IP 172.20.2.0 allow 0.0.0.255 10.0.0.0 0.255.255.255
tunnelnetworks extended IP access list
permit host 172.16.99.2 ip 10.0.0.0 0.255.255.255
IP 172.20.2.0 allow 0.0.0.255 10.0.0.0 0.255.255.255
recording of debug trap
logging source-interface Loopback0
exploitation forest xxxx
not run cdp
!
!
!
!
!
Banner motd ^ CCCAuthorized technician!
^ C
!
Line con 0
line to 0
line vty 0 4
exec-timeout 5 0
Synchronous recording
entry ssh transport
line vty 5 15
exec-timeout 5 0
Synchronous recording
entry ssh transport
!
!
endPlease check if this helps:
http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t8/feature/guide/gt_crpks.html
Federico.
-
Hello world
The vendor name is implemented server in our environment.
We implement VPN site-to-site.
Subnet it is interesting traffic 192.168.50.x
Server IP 192.168.50.1 - Switch1 - ASA - Site to site VPN - provider ASA.
Gateway server is on switch1 if this server requires access to the internet I need to know what config I need on ASA on my site?
I want the server to access the internet through the provider network
Concerning
Mahesh
Hello
Your crypto ACL would be:
ip access-list VPN-TO-VENDOR permit ip 192.168.50.0 255.255.255.0 any
Cryptography providers ACL would be:ip acces-list VPN-TO-COMPANY permit ip any 192.168.50.0 255.255.255.0
All traffic from 192.168.50.0/24 out of the application interface map encryption for any destination would be sent to the seller through the VPN. It will be useful. -
Question creating a site to site vpn
I am trying to configure a site to site vpn to test and through http://www.ciscosecrets.info/en/US/products/ps6120/products_configuration_example09186a0080950890.shtml still unable to establish a connection. I have attached the config for both the 5520's that I use. What Miss me.
Try this if you are pinging from the ASA
management-access inside
-
Site to site VPN, I need all internet traffic to exit the site.
I have 2 sites connected via a pair of SRX5308
A = 192.168.1.0/24
IP WAN = 1.1.1.1
B = 192.168.2.0/24
IP WAN = 2.2.2.2
Now what I need to do, is to have all traffic from B to go to the site one even traffic destined to the internet. That is, I need internet traffic out of our network with the IP 1.1.1.1, even if it is from the network B.
On my I have set up a route 1.1.1.1 of the ISP, then a value by default 0/0 to 192.168.1.1 it ASA knows how to get to the peer VPN is a more specific route, but sends everything above the tunnel, at the remote end which then hairpin of ASA routes internet outside its own WAN port traffic.
I can understand though not how to so the same thing on the pair of SRX5308 they either don't raise the tunnel or internet route to the local site address B.
Anyone have any ideas?
I need to do this because we are logging and monitoring of internet traffic to A site via tapping from upstream to various IDS solutions and will not (cannot) reproduce this to all our remote sites.
Thank you
Dave.
After some more thought and testing I came up with a workable solution to my own problem. I'll share it here in case it can help others.
(1) use the wizard at both ends to implement a normal VPN that connects the two segments of network 192.168.1.0 and 192.168.2.0
(2) go to site VPN - VPN policy remote router192.168.2.1 and click Edit
(a) disable Netbios
(b) select "None" from the drop-down list the remote IP address.
(c) to apply the change
3) go to the VPN-> VPN policy on the head end site (192.168.1.1) and click Edit
(a) disable Netbios
(b) select "None" from the drop-down list the local IP address
(c) to apply the change
Now all the traffic wil go down the VPN tunnel and exit to the internet on the site of head end. Hope this helps others with the same question.
-
SBS 2008 office1 Serv2008 Office 2 need to share assets between them via a site to site VPN tunnel
Hi all.
I really need help on this one.
The office 1 installer running SBS2008 Office 2 running Server 2008.
Each firm has its own FQDN Office 1 CompanyABC 2 A_B_C of the company office.
Each firm has its own internal IP address pool Office 1 192.168.69.xxx and office 192.168.20.xxx 2.
Site to site VPN tunnel between 2 office routers Netgear SRX5308 1 and 2 Netgear FVS318G Office established and working.
Each firm has its own DNS server and acts as a domain controller
How to configure the 2 networks to see each other and be able to use assets on every network (files, printers)?
Is it so simple that the addition of another pool internal IP for each DNS server?
Thanks in advance for your help.
Hello
Your Question is beyond the scope of this community.
I suggest that repost you your question in the Forums of SBS.
https://social.technet.Microsoft.com/forums/en-us/home?Forum=smallbusinessserver
"Windows Small Business Server 2011 Essentials online help"
https://msdn.Microsoft.com/en-us/library/home-client.aspx
TechNet Server forums.
http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer
See you soon.
-
Site to site VPN works only on Cisco 881
I have 2 problems with a cisco 881. The first problem is that Vlan2 (192.168.5.xx) cannot access the internet on the outside. But I know that the router has internet, because I can ping the external ip address. The 2nd problem is that I have a set of site to another upward, but when I test the Site to site I get this error:
destination of traffic of the tunnel must be channelled through the crypto map interface. The destination following (s) doesn't have a routing entry in the routing table
192.168.2.0I copied the config form this router from another cisco 881 work, where everything works. The only difference is that this router needs a site to site vpn connection.
My question is how I can get internet on vlan2 and who can I solve the connection to site to site.
Here's the running configuration:
Building configuration...
Current configuration: 12698 bytes
!
version 15.3
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname Cisco_881
!
boot-start-marker
boot-end-marker
!
AQM-registry-fnf
!
logging buffered 51200 warnings
!
AAA new-model
!
!
AAA authentication login default local
AAA authorization exec default local
AAA authorization network default local
!
!
!
!
!
AAA - the id of the joint session
!
Crypto pki trustpoint TP-self-signed-1151531093
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 1151531093
revocation checking no
rsakeypair TP-self-signed-1151531093
!
Crypto pki trustpoint TP-self-signed-2011286623
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 2011286623
revocation checking no
rsakeypair TP-self-signed-2011286623
!
!
TP-self-signed-1151531093 crypto pki certificate chain
certificate self-signed 01
3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
69666963 31313531 35333130 6174652D 3933301E 170 3135 30343031 31363230
34315A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 31353135 65642D
33313039 3330819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
8100AC6E E7FA8AFD 9D4E206C 2B23DFC1 990AFDB3 98CD84A7 37697253 A7EF2520
0C45190E 298B6E9F E2711580 80DCFBFB 05A6A0BA 347B960B D9DA17FC B1543B9D
FBC048F3 063EBBC5 02391432 F0232A73 EAC7278E 8CB83005 D13A1D47 BEF18198
A 547469, 2 F65ED0E6 249BF517 1E74117D C94BE542 46EE487D A3843F12 364639B 4
0B 090203 010001 HAS 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355
551 2304 18301680 147996F4 3E6D0EE2 2D9065BB D726137C 2DF42ABE 01301D 06
03551D0E 04160414 7996F43E 6D0EE22D 9065BBD7 26137C2D F42ABE01 300 D 0609
2A 864886 F70D0101 8181002A 05050003 677B9BE6 CB60D188 73227C4B 2DC33101
BD448017 EDEF0296 FF7438A3 4C46519B 144C775F 1429CF06 7DB29F2D EB16EE75
22100B 63 0D75511A 98DC57DC EF87BED2 1C1635C8 B5352706 3963037A 4E9B739A
3A1EC9BE 8431BD70 116D3B31 E4A2AC4C 0F934B3F 196AF829 AD537005 6935B 451
EB31DB3F A9BA6D70 65B70D19 D00158
quit smoking
TP-self-signed-2011286623 crypto pki certificate chain
no ip source route
!
!
!
!!
DHCP excluded-address IP 10.10.10.1
DHCP excluded-address IP 192.168.5.1 192.168.5.49
DHCP excluded-address IP 192.168.5.150 192.168.5.254
!
DHCP IP CCP-pool
import all
Network 10.10.10.0 255.255.255.248
default router 10.10.10.1
Rental 2 0
!
IP dhcp Internet pool
network 192.168.5.0 255.255.255.0
router by default - 192.168.5.254
DNS-Server 64.59.135.133 64.59.128.120
lease 6 0
!
!
!
no ip domain search
"yourdomain.com" of the IP domain name
name of the IP-Server 64.59.135.133
name of the IP-Server 64.59.128.120
IP cef
No ipv6 cef
!
!
!
!
!
Authenticated MultiLink bundle-name Panel
!
!
!
!
!
!
!
udi pid C881-K9 sn FTX18438503 standard license
!
!
Archives
The config log
hidekeys
username * privilege 15 secret 5 $1$IBY.$X5/iqYy47a5vAWWuG4/Oa/
username * secret 5 $1$ 17 ST$ QzJMvQnZ9Q.1y7u0rYXFa0
username * secret 5 $1$ L4W9$ zBKpawZ3i5nXxwyS9H6Lf1
!
!
!
!
!
no passive ftp ip
!
!
crypto ISAKMP policy 1
BA aes 256
preshared authentication
Group 2
!
crypto ISAKMP policy 2
BA 3des
preshared authentication
Group 2
isakmp encryption key * address 208.98.212.xx
!
Configuration group crypto isakmp MPE client
key *.
pool VPN_IP_POOL
ACL 100
include-local-lan
10 Max-users
netmask 255.255.255.0
banner ^ practive entered the fieldThis area is reserved for administrators of control systems.
If you are here by mistake, please disconnect immediately.
You have full access to 192.168.125.0 / 0.0.0.255
Support on continue to start your session. ^ C
!
Configuration group customer crypto isakmp PALL
key *.
pool VPN_IP_POOL_PALL
ACL 101
include-local-lan
Max - 1 users
netmask 255.255.255.0
banner ^ practive entered the fieldThis area is limited to the PALL access only.
If you are here by mistake, please disconnect immediately.
You have full access to 192.168.125.0 / 0.0.0.255
Support on continue to start your session. ^ C
ISAKMP crypto profile vpn_isakmp_profile
game of identity EMT group
client authentication list default
Default ISAKMP authorization list
client configuration address respond
virtual-model 1
ISAKMP crypto profile vpn_isakmp_profile_2
match of group identity PALL
client authentication list default
Default ISAKMP authorization list
client configuration address respond
virtual-model 2
!
!
Crypto ipsec transform-set esp - aes 256 esp-sha-hmac VPN_TRANSFORM
tunnel mode
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
tunnel mode
!
Profile of crypto ipsec VPN_PROFILE_MPE
Set the security association idle time 3600
game of transformation-VPN_TRANSFORM
vpn_isakmp_profile Set isakmp-profile
!
Profile of crypto ipsec VPN_PROFILE_PALL
Set the security association idle time 1800
game of transformation-VPN_TRANSFORM
vpn_isakmp_profile_2 Set isakmp-profile
!
!
!
map SDM_CMAP_1 1 ipsec-isakmp crypto
Description Tunnel to208.98.212.xx
the value of 208.98.212.xx peer
game of transformation-ESP-3DES-SHA
match address 102
!
!
!
!
!
!
interface Loopback0
IP 192.168.40.254 255.255.255.0
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
switchport access vlan 2
no ip address
!
interface FastEthernet3
switchport access vlan 2
no ip address
!
interface FastEthernet4
IP address 208.98.213.xx 255.255.255.224
IP access-group 111 to
NAT outside IP
IP virtual-reassembly in
automatic duplex
automatic speed
map SDM_CMAP_1 crypto
!
type of interface virtual-Template1 tunnel
IP unnumbered Loopback0
ipv4 ipsec tunnel mode
Tunnel VPN_PROFILE_MPE ipsec protection profile
!
tunnel type of interface virtual-Template2
IP unnumbered Loopback0
ipv4 ipsec tunnel mode
Tunnel VPN_PROFILE_PALL ipsec protection profile
!
interface Vlan1
Description of control network
IP 192.168.125.254 255.255.255.0
IP access-group CONTROL_IN in
IP access-group out CONTROL_OUT
IP nat inside
IP virtual-reassembly in
IP tcp adjust-mss 1452
!
interface Vlan2
Description Internet network
IP 192.168.5.254 255.255.255.0
IP access-group INTERNET_IN in
IP access-group out INTERNET_OUT
IP nat inside
IP virtual-reassembly in
!
local IP VPN_IP_POOL 192.168.40.100 pool 192.168.40.150
local IP VPN_IP_POOL_PALL 192.168.40.151 pool 192.168.40.152
IP forward-Protocol ND
IP http server
23 class IP http access
local IP http authentication
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
!
IP nat inside source static tcp 192.168.125.2 25000 25000 FastEthernet4 interface
IP nat inside source overload map route SDM_RMAP_1 interface FastEthernet4
IP route 0.0.0.0 0.0.0.0 FastEthernet4 permanent 208.98.236.xx
!
CONTROL_IN extended IP access list
Note the access control
Note the category CCP_ACL = 17
allow any host 192.168.125.254 eq non500-isakmp udp
allow any host 192.168.125.254 eq isakmp udp
allow any host 192.168.125.254 esp
allow any host 192.168.125.254 ahp
IP 192.168.125.0 allow 0.0.0.255 192.168.125.0 0.0.0.255
Note the VPN access
IP 192.168.125.0 allow 0.0.0.255 192.168.40.0 0.0.0.255
Note Access VNC
permit tcp host 192.168.125.2 eq 25000 one
Comment by e-mail to WIN911
permit tcp host 192.168.125.2 any eq smtp
Note DNS traffic
permit udp host 192.168.125.2 host 64.59.135.133 eq field
permit udp host 192.168.125.2 host 64.59.128.120 eq field
Note Everything Else block
refuse an entire ip
CONTROL_OUT extended IP access list
Note the access control
IP 192.168.125.0 allow 0.0.0.255 192.168.125.0 0.0.0.255
Note the VPN access
ip permit 192.168.40.0 0.0.0.255 192.168.125.0 0.0.0.255
Note Access VNC
allow any host 192.168.125.2 eq 25000 tcp
Comment by e-mail to WIN911
allow any host 192.168.125.2 eq smtp tcp
Note DNS responses
allowed from any host domain eq 192.168.125.2 udp
Note deny all other traffic
refuse an entire ip
INTERNET_IN extended IP access list
Note Access VNC on VLAN
allow any host 192.168.125.2 eq 25000 tcp
Note block all other controls and VPN
deny ip any 192.168.125.0 0.0.0.255
deny ip any 192.168.40.0 0.0.0.255
Note leave all other traffic
allow an ip
INTERNET_OUT extended IP access list
Note a complete outbound Internet access
allow an ip
WAN_IN extended IP access list
allow an ip host 207.229.14.xx
Note PERMIT ESTABLISHED TCP connections
allow any tcp smtp created everything eq
Note ALLOW of DOMAIN CONNECTIONS
permit udp host 64.59.135.133 eq field all
permit udp host 64.59.128.120 eq field all
Note ALLOW ICMP WARNING RETURNS
allow all all unreachable icmp
permit any any icmp parameter problem
allow icmp all a package-too-big
allow a whole icmp administratively prohibited
permit icmp any any source-quench
allow icmp all once exceed
refuse a whole icmp
allow an ip
!
auto discovering IP sla
not run cdp
!
allowed SDM_RMAP_1 1 route map
corresponds to the IP 103
!
access-list 1 remark out to WAN routing
Note CCP_ACL the access list 1 = 16 category
access-list 1 permit 192.168.125.2
access-list 1 permit 192.168.5.0 0.0.0.255
Note access-list 23 SSH and HTTP access permissions
access-list 23 permit 192.168.125.0 0.0.0.255
access-list 23 permit 192.168.40.0 0.0.0.255
access-list 23 allow one
Note access-list 100 VPN traffic
access-list 100 permit ip 192.168.125.0 0.0.0.255 any
access-list 100 permit ip 192.168.40.0 0.0.0.255 any
Note access-list 101 for PALL VPN traffic
access-list 101 permit ip 192.168.125.0 0.0.0.255 any
Note access-list 102 CCP_ACL category = 4
Note access-list 102 IPSec rule
access-list 102 permit ip 192.168.5.0 0.0.0.255 192.168.2.0 0.0.1.255
Note access-list 103 CCP_ACL category = 2
Note access-list 103 IPSec rule
access-list 103 deny ip 192.168.5.0 0.0.0.255 192.168.2.0 0.0.1.255
access-list 103 allow ip 192.168.5.0 0.0.0.255 any
access-list 103 allow the host ip 192.168.125.2 all
Note access-list 111 CCP_ACL category = 17
access-list 111 permit udp any host 208.98.213.xx eq non500-isakmp
access-list 111 permit udp any host 208.98.213.xx eq isakmp
access-list 111 allow esp any host 208.98.213.xx
access-list 111 allow ahp any host 208.98.213.xx
Note access-list 111 IPSec rule
access-list 111 permit ip 192.168.2.0 0.0.1.255 192.168.5.0 0.0.0.255
Note access-list 111 IPSec rule
access-list 111 permit ip 192.168.2.0 0.0.1.255 192.168.4.0 0.0.1.255
access-list 111 permit udp host 208.98.212.xx host 208.98.213.xx eq non500-isakmp
access-list 111 permit udp host 208.92.12.xx host 208.92.13.xx eq isakmp
access-list 111 allow esp host 208.92.12.xx host 208.92.13.xx
access-list 111 allow ahp host 208.92.12.xx host 208.92.13.xx
access-list 111 permit icmp any host 208.92.13.xx
access-list 111 permit tcp any host 208.92.13.xx eq 25000
access-list 111 permit tcp any host 208.92.13.xx eq 22
access-list 111 permit tcp any host 208.92.13.xx eq telnet
access-list 111 permit tcp any host 208.92.13.xx eq www
!
!
!
control plan
!
!
!
MGCP behavior considered range tgcp only
MGCP comedia-role behavior no
disable the behavior MGCP comedia-check-media-src
disable the behavior of MGCP comedia-sdp-force
!
profile MGCP default
!
!
!
!
exec banner ^ C
% Warning of password expiration.
-----------------------------------------------------------------------Unplug IMMEDIATELY if you are not an authorized user
^ C
!
Line con 0
no activation of the modem
line to 0
line vty 0 4
access-class 23 in
password *.
transport input telnet ssh
transportation out all
line vty 5 15
access-class 160 in
password *.
transport of entry all
transportation out all
!
max-task-time 5000 Planner
Scheduler allocate 20000 1000
!
endThank you.
It seems that DNS has failed, because it is indeed happened to internet, but it does not work when internet DNS resolution.
Go ahead and try to ping this 157.166.226.25, and it's on the browser http://157.166.226.25/, CNN.com. Let's try those. Also just in case where to configure a DNS SERVER on your router.
- http://www.cisco.com/c/en/us/support/docs/ip/domain-name-system-dns/2418...
Disable any ZBF just in case.
David Castro,
Kind regards
-
You try to run a Site to site VPN and remote VPN from the same IP remotely
We currently have a site to site VPN configuration between our offices call center and a 3rd party that allows them to access our training to their employees to use environment while being trained on our systems. This tunnel is running between our ASA and their ASA without problem; However, when we have managers come out to the call center, they are unable to use remote VPN to access our office.
Apparently the same IP peer remote that we use for our site to the other tunnel is the same IP that our managers use to access the internet when they are on-site with the customer. When I look at the logs it shows the VPN attempt and then I get treatment Information Exchange has failed. So from what I can understand when our managers are trying to connect to our firewall from the same IP address as the counterpart of site to site it automatically tries to create a tunnel, according to the information of the site to the other tunnel. If our managers are anywhere else, they can connect through remote VPN with no problems.
My question is if anyone knows of a way to make the firewall allow VPN site to site and remote connections with the same remote IP address.
Hi John,.
Basically, in older versions, when you hit a static encryption card and you does not match this static encryption completely map the connection continues until the dynamic encryption card. For this reason, you can connect your IPSec clients before. A bug has been opened on this vulnerability.
CSCuc75090 Details of bug
The crypto IPSec Security Association are created by dynamic crypto map to static peers
Symptom:
When a static VPN peer adds all traffic to the ACL crypto, a surveillance society is based even if the pair IP is not allowed in the acl to the main façade encryption. Are these SA finally put in correspondence and commissioning the dynamic crypto map instance.
Conditions:
It was a planned design since the first day that allowed customers to fall through in the case of static crypto map did not provide a necessary cryptographic services.
The SA must be made from a peer configured statically and a dynamic crypto map instance must be configured on the receiving end.
Workaround solution:
N/A
Some possible workarounds are:
Configure a static nat device when you try to use the remote VPN if the firewall remotely will be hit with a different public IP address. It would be a good solution, but it will depend on how many ip addresses public you have available, if you really want one of these ip addresses for that access.
Also, I thought you could use AnyConnect instead of the IPSec VPN client. I don't know how many users need to connect from your PC to the remote site, but the ASA has 2 licenses SSL available that you could use. Because Anyconnect uses the SSL protocol, it won't have a problem on your environment.
Below some information:
Hope this helps,
Luis.
Maybe you are looking for
-
After the 19 FF update, whenever I open a new session of FF, it restores all previous session, I had used last. I already checked to make sure that the setting "when Firefox starts: show my home page" is selected. How can I fix it?
-
Side scroll bar to the top does not work
My high side scroll bar does not work with the arrow pointing upwards. I manually enter the box scroll and pull it upwards. I updated Firefox uninstalled and reinstalled and it still does not work. It worked on my laptop but not on my desktop.
-
At startup. I go as far as the login screen (showing the four accounts). But this screen is dead: there is no response to finger taps or gestures. only by pressing the power button gets a response (immediate panic stop) There is a story backward. Yes
-
Unable to download Windows Update (error 800703E7)
original title: what is 800703E7 error and how to fix it? My system does not download microsoft updates, it comes up with error 800703E7
-
Mini 1000 bios access/reset
n/m-HP MINI 1116NR o.s. and NO KNOWN error - ERROR FATAL... SYSTEM ORDER. CNU918088X